Search Documents

By Ross Seedaman

The specification of roof support needs to consider rock strength, imposed ground stresses, and more importantly the bedding and joint structure of the immediate roof rocks. A database structure has been developed that allows these considerations to be incorporated into modern mine planning software so that better predictions of mining rates can be made. Rock strength is estimated from core and/or geophysical logs (especially the sonic velocity log) and ground stresses are estimated from depth of cover and knowledge of the regional stress field. The database is unique in the way it addresses bedding structure. Only 10 roof lithologies are allowed and these are allocated a numerical value that reflects an increase in the average spacing of bedding partings. These are referred to as 'Geotechnical Ferm Units' (GFU). The locations of all bedding discontinuities logged in the core are entered into the database and referenced to the GFUs. It has been found that, within each GFU, bedding spacing follows a negative exponential distribution and so it is a simple matter to predict the probability of the occurrence of any roof beam thickness. Output from the database can include plans of roof strength, the onset of overstressing, and the statistics of the distribution of beam thickness in the immediate roof.

Jan 1, 2003

By J. F. T. Agapito

Overcore measurements at the North Fork Valley (NFV) coal mines in western Colorado have shown that horizontal stresses are highly anisotropic. Measurements have been made in four mines at various depths. In many measurements, the maximum horizontal stress is three to four times higher than the minor horizontal stress. At the West Elk Mine, maximum and minimum horizontal stresses of 24 MPa and 6 MPa, respectively, have been measured at depths of 640 meters (m). Under highly anisotropic stress conditions, ground control problems associated with both high and low horizontal stresses can develop. While high horizontal stresses can produce cutter failures and floor heave, low horizontal stresses can allow block fallouts. This paper summarizes the horizontal stress measurements in NFV mines and, in particular, in the West Elk Mine where their role in roof fall and floor heave failures is discussed. This experience has led to an improved use of ground support and safer mining operations at depths of 640 to 700 m.

Jan 1, 2005

By K. Hanna

This manuscript describes an extensive ground control study at the Inland Steel No. 2 Mine near McLeansboro, IL, conducted by the U.S. Department of the Interior's Bureau of Mines (USEM) in cooperation with Inland Steel Coal Co. The mine experiences severe ground control problem primarily due to high horizontal stress, particularly at entry intersections. Mine experience has shown that reorienting mine entries, modifying the bolting pattern, and altering the mining sequence are effective in reducing the severity of roof falls and out-of-seam dilution. However, the frequency of roof falls has not been significantly reduced. This research project was designed to provide a thorough explanation of the intersection failure mechanism through combined analyses of company in-mine experience and Bureau field measurements. Stresses and deformations were monitored in a four-way intersection during all stages of development and were related to site observations and theoretical analyses. The results of the combined analyses indicate that high horizontal stress is the predominant factor contributing to intersection roof falls in the Inland Steel No. 2 Mine. The horizontal stress induces shear zones to form along the outby 1 ribs, causing the immediate roof layer to detach 1 and behave as a cantilever beam oriented diagonally across the intersection and parallel to i the maximum horizontal principal stress. As the shear zone progresses upward, roof layers successively detach and fail, forming a dome-type roof fall.

Jan 1, 1986

By Wilfried Ufer

[1. Einführung in die Problematik 1.1 Die Bedeutung des Schildausbaus Seit fast 30 Jahren ist die Konkurrenzsituation auf dem Primärenergiemarkt der Bundesrepublik Deutschland durch einen von Erdöl and Erdgas geführten and insbesondere gegen die Steinkohle gerichteten Verdrängungswettbewerb gekennzeichnet, der den Steinkohlenbergbau zu tiefgreifenden RationalisierungsmaBnahmen zwang. In diesem Zusammenhang kam es Anfang der 70er Jahre zur Einrührung des Schildausbaus, der eine erhebliche Produktivitätssteigerung in den Strebbetrieben zur Folge hatte and damit die Uberlebenschance des Steinkohlenbergbaus in der Bundesrepublik Deutschland enorm verbesserte. Der Grund hierfdr lag darin, daB der Schildausbau im Vergleich zu dem vor ihm eingesetzten Rahmen- and Einzelstempelausbau eine wesentlich hdöhere Ausbauleistung erbrachte, weil er sich weit weniger empfindlich gegen Hangendausbruche and aus dem Alten Mann hereinbdschende Bruchberge erwies. So erklärt sich auch die stürmische Entwicklung and die schnelle Verbreitung des Schildausbaus. Bereits 1975 stammte rd. 50 % der Fdrderung aus Schildstreben, 1990 waren es fiber 75 % and heute sind es fiber 90 %. 1.2 Die Staubentstehung beim Schildausbau Die Erfolge des Schildausbaus sind unbestritten. Jedoch nahmen :nit seiner Einführung die Probleme der Staubentstehung and Staubbekämpfung im Vergleich zum Ein zelstempel- and Rahmenausbau erheblich zu. MaBgebend dafür sind hauptsächlich folgende Gründe: - Abbau von dozen nit gebrächen, weichen Hangendschichten, die erst durch Schildausbau abbaubar wurden, - Zerkleinerung des auf den breiten Kappen aufliegenden Bergematerials infolge der höheren Ausbaustiltzkrafte des Schildausbaus, Zermahlen der sick in die Spaltabdichtungen hineinarbeitenden Bergestückchen, - Erhöhung der Wettergeschwindigkeit infolge der durch die Baufarm des Schildausbaus bedingter. Verkleinerung des Strebquerschnitts verbunden mit der Aufwirbelung and Aussichtung von Staub, - Aufwirbelung von bereits abgelagertem Staub im Bruchraum beim Hereinbrechen der Dachschichten. Die genannten Gründe treten zumeist nicht in jedem Abbaubetrieb gleichzeitig auf. Sie rind vielmehr u.a. abhängig vom Ausbautyp, von den Gebirgsverhältnissen and von der Abbaugeschwindigkeit. Trotzdem ergeben sich beim Vorrücken des Ausbaus in der Regel hohe Staubkonzentrationen, die deswegen besonders kritisch sind, weil es sich um quarzhaltigen Feinstaub handelt, der besonders gesundheitsschädlich ist. Die Hauptzutrittsstelien]

Jan 1, 1984

By Frank Kendorski

Several startup or longtime underground stone mines have experienced unanticipated roof control difficulties due to the variable geologic character of the roof strata. Careful mapping of roof conditions, and identification of controlling geologic and mine geometric factors using sedimentological descriptors, lead to an understanding of the mechanisms causing roof problems. Types of bedding plane features can be categorized into geometric, internal structures, bedding-plane markings, deformed bedding, solution structures, and accretionary structures. Factors such as encountering open water-filled master joints; roof strata delamination due to internal water pressures; local karst features with mud, sand, and water hazards; and sudden loss of limestone roof due to paleo-channel erosion are some recent problems described.

Jan 1, 2002

By Kikuo Matsui

Standing supports such as steel arches or square work supports along with the necessary struts and lagging have been traditionally employed in the longwall gateroads of the Japanese underground coal mines. Miike Colliery has newly introduced the interpanel-pillar mining system and the strata bolting system in gateroads to raise productivity levels and reduce operating costs. The Department of Mining Engineering, Kyushu University, in cooperation with the Miike Colliery and the Coal Mining Research Center, Japan (CMRCJ), has been conducting research into the optimum design of strata bolting as a primary support system in longwall gateroads. This paper presents a brief overview of the current state of strata bolting technique being applied in longwall gateroads at the Miike Colliery and discusses some problems in employing bolting.

Jan 1, 1993

By Jisheng Han

Interaction effect exists when two or more neighboring seams are mined. The mining activity in one seam causes stress redistribution and strata movement in both the roof and floor. When the thickness of interburden between two neighboring seams is small, some hazardous situations like roof cutters, roof falls, floor heave and rib spalling in one seam may be encountered due to the effect of the mining activity in the other seam. An investigation about roof cutters, roof falls and floor heave was conducted in a West Virginia mine to study the interaction of multi-seam mining. The mine is mining the Sewickley Seam, which is about 90 ft above the Pittsburgh Seam which was mined in the 1960's using room and pillar method. The roof falls and other stability anomalies of entries observed underground in the Sewickley Seam were found closely related to the location of barrier pillars and gas well pillars left in the Pittsburgh Seam. Then numerical modeling was carried out to check the interaction between these two seams of mining. It was found through the modeling results that in the areas where pillaring operation was conducted in the Pittsburgh Seam, the stress concentrated less in the Sewickley Seam while near the edge of the gas well pillars and barrier pillars, high stress concentration was observed. It was concluded that under the geological conditions of the study mine, the entries stability would be affected by the lower seam mining activity, especially above or around the edges of pillars.

Jan 1, 2005

By Kewal K. Kohli

An investigation was performed to determine the sequence of events which caused the 1987 surface subsidence and related damage to several homes in Walker County, Alabama, USA (see Figure 1). Surface affects compared to mine maps indicated the subsidence to be mine related. However, two coal seams had been worked under this area. The upper seam, the American seam ranged from 250 to 280 feet beneath the surface in the area in question. It was mined-out before 1955 by room-and-pillar method leaving in place narrow-long pillars to support the overburden strata, and abandoned in 1955. The lower seam, the Mary Lee seam, ranged from 650 to 700 feet beneath the surface. The Mary Lee seam had been abandoned in 1966 and subsequently became flooded. The dewatering of the Mary Lee seam workings in 1986 caused the submerged pillars to be exposed to the atmosphere. Due to multiple seam mining and the fact that workings had been inundated then dewatered, a subsurface investigation ensued to determine the sequence and ultimate cause of surface subsidence. Core sample tests with fracture analysis in conjunction with "down-the-hole" TV camera inspections provided necessary information to determine that the subsidence started in the lower seam and progressed through the upper coal seam to the surface. Evidence from the investigation program established that dewatering of the lower seam workings caused the marginally stable support pillars and the roof to collapse. This failure triggered additional subsidence in the upper seam which broadened the area of the influence at the surface.

Jan 1, 1992

By Tom Denton

The bolt design criteria, since it was first published by Dr. John Stankus (Stankus, 1997), has been recognized as an important tool in ground control design. This concept is based on the Optimum Beam Building Effect (OBE), which is defined as the roof beam that has no separation above or within the bolted range and having the shortest bolt possible. This paper will present an application of this concept at the American Coal Company. Galatia mine. This mine previously used a 6' and 7' length bolt. However, since seam thickness has gotten smaller in the Southern area of the nine, a two-piece bolt is required. A two-piece bolt increases ground control costs and delays production. Therefore, a one-piece, shorter bolt, if feasible, can reduce costs and expedite development. In this analysis, Computer modeling is first conducted to determine bolt length and installed load. Second, a special bolt is developed, that can achieve the proper installed load as determined by the computer modeling. Third, underground bolt pull and load cell tests were conducted to evaluate bolt performance. Finally, an underground "bench" test was conducted. The test results have shown that entry convergence in the short bolt (5) test area is less than the 6' bolt area. Overall roof condition in the test area was as good as the 6' bolt area. Based on this analysis, the mine has converted to a shorter bolt in the low seam area and it is working well.

Jan 1, 2000

By A. Wilkinson

An investigation into the performance of support systems that are currently used in South African coal mines was conducted. Five most critical components of a support system have been identified. These components are resin, bolt, hole, machinery/equipment and the rock type. All five of these components are equally important as failure in any of these components will result in an inadequate support system. The performance of resin used in South Africa was investigated through in situ short encapsulated pull tests. The results indicated that in the majority of pull tests, failure took place at the rock-resin interface, indicating that the rock failed before the resin shear strength had been reached. It is therefore concluded that the strength of resin currently used in South Africa is adequate. It is found that although the maximum bond strengths achieved form both resin suppliers were similar, there was a considerable difference in the stiffhess of the resins. Roof bolt diameters and rib heights of bolts from three major manufacturers were evaluated (approximately 80 roof bolts from each manufacturer). The results showed there is a significant variation in bolt diameters and rib heights in the same batch in roof bolts supplied by certain manufacturers. The results also showed that on average there are insignificant differences between the parameters that determine the bolt profile (rib angle, spacing between the ribs and rib thickness). The influence of these parameters on bolt performance was very small and could not be established in situ. Roof bolts from four major suppliers were also evaluated through in situ short encapsulated pull tests. The results showed that the reinforcing system using roof bolts from all four manufacturers performed almost identically in sandstone, but somewhat differently in other rock types. The effect of bit types was evaluated. Both the stresses and the maximum loads obtained from the two-prong bits were greater than those obtained from a spade bit. Borehole annulus was found to be another important parameter that determined the support performance, and was investigated. The results from these tests showed that an annulus between 2.8 mm 4.5 mm resulted in the highest bond strengths. The results also showed that as the annulus drops below 2 mm, it appears to have a negative effect on the bond strength. The effect of wet and dry drilling on support performance was investigated. The results showed that wet drilling can-provide relatively greater system stiffnesses and slightly greater bond strengths. Short encapsulated pull test results showed very distinct differences between bolt system performance in different rock types and that sandstone produces significantly better results than shale and coal. From the results it is concluded that rock type is probably the primary factor influencing support system performance. A detailed investigation into the specifications of roofbolters that are currently being used indicated that the quality of installation of a support system is directly related to the performance of the equipment that is used to install the bolts. The important parameters, torque, thrust and speed of bolting equipment were investigated. The results showed that there are significant variations in these parameters in South African roofbolters.

Jan 1, 2005

By M. G. Schuerger

The United States Steel Mining Company, Inc., (USM) Lynch District, operated the No. 37 Mine in the Harlan coal seam, Harlan County, Kentucky, from 19'2 until its sale to Arch of Kentucky in 1984. Overburden depth varied from 400 to 2000 feet and mining height varied from 8 to 12 feet. In 1981, because of deep overburden, high seam height, and previous pillar stability problems, U. S. Steel Research and the Lynch Mining District entered into a joint project to measure longwall pillar stress. Eight gateroad pillars were instrumented with a total of 86 vibrating-wire stressmeters under overburden depths varying from 500 to 1550 feet. Stress-increase measurements were taken during: (1) pillar development, (2) retreat of longwall panel No. 1, and (3) retreat of longwall panel No. 2. Total average pillar stress was approximately three times the pre-mining stress with total stress at an individual meter reading 5.5 times the pre-mining stress. When maximum, measured average pillar stress was compared to pillar strength predicted by several popular pillar design methods, the pillars were found to be stronger than predicted. This paper will summarize the pillar instrumentation program and present the results. Stress distributions, average measured pillar stress, and comparison of measured pillar stress to predicted pillar strength by several design methods will be given.

Jan 1, 1984

Since the initial development and trials of FLEXIBOLT flexible roof bolts, further comparative testing and product development has been completed as part of the changeover to this roof support system at two Australian longwall operations, Ellalong and Angus Place Collieries. Details of the practical implementation of FLEXIBOLTS at both collieries are outlined together with their impact on roadway development rate productivity. At Ellalong where fully encapsulated 2.1 m long bolts are used, the reduction in bolt density is discussed with respect to both support system design and work force acceptance. The impact of shear deformation on bolt loading is described. Bolts longer than the working height have been required at Angus Place to achieve a suitable bolt anchorage horizon. Details of the long hole drilling and the benefits of a two stage grouting procedure are outlined. Improvements in roof conditions which have resulted from the inclusion of FLEXIBOLTS into the overall roof support strategy at Angus Place are described. Their importance to the viability of the Angus Place operation is also highlighted.

Jan 1, 1994

By Erik Westman

Tomographic imaging, commonly known as a CAT-scan or CT-scan, is used in the medical field to generate a picture of the interior of a body. Current research is applying this method to bodies of rock so that rock failure can be better understood and predicted. This paper discusses the basic principles of tomography and describes recent developments in the use of seismic tomography in longwall coal mines, including results from a bump-prone longwall coal mine and continuing research.

Jan 1, 2003

By J. A. Nemcik

Although floor failure at longwall faces has been traditionally associated with a soft floor, in many csses floor buckling has been observed just ahead of the longwall supports, despite the floor being a competent rock The floor failure is associated with the presence of weak bedding planes in the floor and the movement of strata towards the goaf opening. This paper presents the principles of the floor failure based on numerical modelling and field observations and outlines the practical approach to estimate the risks involved with floor failure.

Jan 1, 1995

Excessive roadway closure in the gateroads impedes the passage of equipment, supplies, personnel and ventilation air in longwall panels. This pager describes several factors that influence the gateroad stability and presents some measures to alleviate the problem.

Jan 1, 1994

By Hamid R. Nikraz

This paper reports the finding of a comprehensive investigation carried out to evaluate the compaction characteristics of saturated sandstone aquifers in the Collie Coal Basin under conditions anticipated during dewatering operations. A triaxial technique has been adapted to evaluate the compaction characteristics of the sandstone aquifer in the Collie Basin. This technique, which allows the strata stress regime to be reproduced by triaxial loading with zero lateral strain, also provides a precise evaluation of lateral stresses and consequently Poisson's ratio under in situ conditions. The paper contains a description of the equipment commissioned, test techniques, results, analysis and interpretation of the data obtained. The testing evaluation techniques are general in nature and can be applied to field situations in locations where similar weak sandstones occur.

Jan 1, 1993

By Andrew P. Schissler

Cyprus Shoshone is an underground coal mine in southern Wyoming owned by Cyprus Coal Company, a subsidiary of Cyprus Minerals Company. To date, seven longwall panels have been extracted from the pitching seam under increasing depth of cover from 150 ft to 1200 ft. The purpose of this paper is to describe the geology, rock mechanics needs identification, design, testing and successful application of the current headgate/tailgate cribbing system. The immediate roof of the Shoshone is unique in that the first 50 ft of lithology is interbedded mudstones. The mudstone is slickensided, highly friable and has characteristics of unconsolidated fill relative to self-spanning and beaming abilities. Finite element modelling analysis of the overall geomechanical environment showed the mudstone to yield under applied longwall abutment stress. Roof bolt system design methodology also pinpointed the relative weakness of the mudstone roof. In-mine entry vertical convergence and weight response from the mudstone identified the need to design a crib which had superior weight capacity over a wide range of convergence. Design of a structure ensued to achieve the superior strength properties of wood parallel to the grain and the displacement properties of wood perpendicular to the grain. Testing of the prototype structure along with other alternative wooden cribs was done at the U.S. Bureau of Reclamation facility in the Denver Federal Center, Colorado. The test results verified the design. Crib placement pattern was chosen to maximize support with a confined core crib under the high convergence area. The design has been successfully installed in over 5,000 ft of headgate entry in the 11 left panel.

Jan 1, 1993

By Robert W. Bruhn

A 125 foot high steel lattice frame tower supporting a 500 kV EHV transmission line and located over the gateroads of a longwall mining operation was subjected to ground movements from the mining of adjacent longwall panels. Under an agreement with the owner of the powerline, the mine operator was required to minimize mining impacts on the transmission line. In view of this requirement, the mine operator prepared a forecast of the expected subsidence ground movements prior to the onset of mining. These forecasts, in conjunction with finite element analyses of the tower superstructure under the imposed ground movements and wind loadings. suggested that the structural capacity of the tower would probably be diminished little, if at all, by mining. Ground movements determined by survey during mining of the two longwall panels were found to be in close agreement with predictions. Strains measured in selected tower members during mining generally agreed with values calculated by the finite element analyses. The study confirmed a methodology to predict subsidence and to assess its effects on steel lattice transmission towers.

Jan 1, 1990

By Alan Campoli

The Eclipse System was developed by Minova USA Inc. formerly Fosroc Inc. to improve the performance of 5/8-inch deformed rebar fully grouted into a one inch borehole. An 1/8-inch offset bolt head combined with specially formulated Eclipse Lokset resin cartridge results in reduced gloving and increased mixing efficiency. The benefits of the Eclipse System have been demonstrated, under the supervision of MSHA, in Kentucky, West Virginia and Illinois coal mines in partnership with Excel Mining Systems, a leading roof bolt manufacturer. Over 100,000 units have been installed to date. Eclipse system bolts exposed during overcast construction at the Panther Mine of Cumberland Resources displayed an extremely well mixed, uniform resin anchorage over the entire bolt length.

Jan 1, 2003

By Kenneth L. Johnson

The effects of underground longwall coal mining on flow in perennial streams within the Pittsburgh seam basin were evaluated. Four streams above four different longwall mines were studied. Overburden depths at the study sites ranged from 500 to 600 feet. At all four locations, premining streamfow measurements were made to establish baseline flow conditions. Measurements were then repeated at each location after the longwall face passed beneath the stream. At one location, in which the longwall panel axis was roughly parallel to the stream, the streamflow was monitored as the longwall face advanced. Measurements at this location showed that temporary flow reduction occurred as the face advanced underneath; however, after the tensile portion of the traveling subsidence profile passed, this effect was lessened. At two of the sites in which the stream was roughly perpendicular to the panel axis, postmining streamfow increased across the panel and decreased over the development headings, such that the net lateral change in streamflow across the fully subsided panel and associated development headings was small compared to the measured flow.

Jan 1, 1997