Search Documents

By Enrique Fernández

INTRODUCTION The high speed rail link between Madrid and Asturias, in the North of Spain, has encountered in the Cantabrian range the biggest challenge of the whole line, a very deep tunnel, 25 km long through a foreseen difficult geology. This tunnel was divided in the following four lots for construction: ¦Lot 1: Pola de Gordón- Folledo. L=10,7 km ¦Lot 2: Folledo-Viadangos. L=4,166 m ¦Lot 3: Viadangos- Los Pontones. East tube. L=10,4 km ¦Lot 4: Viadangos- Los Pontones. West tube. L=10,4 km. Dragados S.A. leading a JV was contracted to design and built the Lot 2 on the captioned Pajares High Speed Railway Tunnel. The Lot 2, comprising the middle third section of the 25 km long tunnel has an additional challenge: the construction of one access from the surface to allow it own construction. Feasibility reports and preliminary design do not foresee the use of TBM due to the risk of squeezing ground at the deepest area of the tunnel. On the other hand, conventional NATM excavation of the twin tunnels and ancillary works, including access shafts were against the expected construction schedule by the client, due to the poor ground foresee at the early stage.

By Glen Church, Don W. Deere, Christoph M. Goss

The Standley Lake Dam Rehabilitation Project in Colorado included the complete replacement of the outlet works. This required two 1.8m (6 ft) diameter microtunneled wet lake taps, 380m and 186m (1246 ft and 636 ft) long, a permanent valve shaft 12.2m(40 ft) wide and 32m (105 ft) deep, and a 3.5m (11.5 ft) diameter (962 foot long) outlet tunnel driven with a roadheader. The tunnels were driven in low-strength, expansive, and slickensided claystone. The paper addresses the site investigation, shaft construction, roadheader performance, shotcrete placement, tunnel convergence, long distance microtunneling, and wet lake taps.

Jan 1, 2005

By A. Robles-Vega

In recent years, tellurium has been extensively used in the manufacture of semiconductor materials. For this type of application, high-purity tellurium is required. Selenium, lead and silicon are usually the main impurities in tellurium. During the electrolytic refining of copper, tellurium gold and silver are collected in the anode slimes. A pyrometallurgical treatment is used to recover gold and silver from the decopperized anode slimes whereas tellurium is oxidized and skimmed off from the refining furnace as a Na2CO3-based slag. In the slag, tellurium is present as sodium tellurite (Na2TeO3), which is further water-leached from the slag. The first step in the conventional process for tellurium recovery consists of the precipitation of the tellurium contained in the leaching solution as tellurium dioxide (TeO2). The solid TeO2 is then dissolved under acidic conditions for its further reduction with sulfur dioxide gas (SO2). In this paper, an alternative route for tellurium production is presented in which a sodium tellurate [Na2TeO4] intermediate is obtained by oxidation of the sodium tellurite in an alkaline solution following the water leaching step. Sodium tellurate is then dissolved in acid media and high-purity tellurium is obtained by reduction with SO2 gas. Experimental tests under laboratory conditions indicate that the novel process yields higher precipitation selectivity for tellurium than the conventional process. A comparison of its efficiency concerning impurities co-precipitation with respect to the conventional process is discussed.

Jan 1, 2009

By H. K. Lin

The effect of metallic iron fines on froth flotation of a sulfide ore was examined by comparing the flotation results with and without iron fines present in the flotation feed. Mild steel and ceramic laboratory ball mills were used to grind 600 g sulfide ore charges. The mild steel ball mill generated approximately 4.6 g of iron fines (0.8% of the ore charge mass) when grinding to a product size of 80% passing 200 mesh (75 mm). When a low dosage of a weak xanthate collector was used in flotation, the impact of the iron fines on sulfide flotation was marked. Higher dosages of stronger xanthate collectors rendered the impact of the iron fines much less significant. Consumption of the collectors by the powdery iron fines is believed to cause the differences observed in the flotation results. A galvanic effect on flotation was not evident in this study. The impact of the iron fines on silicates depression was also examined.

Jan 1, 2008

By T. Mudder, R. Cellan, R. Waterland, J. Whitlock, B. N. Nelson

The effectiveness of anaerobic in-situ biological treatment for the immobilization of selenium, molybdenum, and uranium in an alluvial aquifer was examined using long-term column tests. A series of organic substrate and nutrient combinations were tested to determine removal effectiveness, optimum supplement concentrations and ratios. Final column testing was conducted to determine the chemical stability of the treatment by-products/treatment compounds by dosing the columns continuously with elevated redox untreated alluvial groundwater.

Jan 1, 2002

By J. McMurray

Introduction Uranium was recovered from mining of collapse breccia pipe deposits in the Arizona Strip district in northwestern Arizona (Figure 1) intermittently between 1956 and 1990, with cumulative production having totaled 23.3 million pounds of U3O8 (8960 tU) at an average grade of 0.6% U3O8. Production was suspended in 1990 because of low uranium prices, but the recent resurgence in market price once again makes the breccia pipe deposits potentially attractive exploration and development targets. This paper describes: (1) formation of the pipe structures and their metallogenesis; (2) mining and milling of breccia ore; and (3) potential roadblocks to development of new breccia pipe mines. Breccia Pipe Formation Formation of the breccia pipes began in cave systems formed during development of karst topography in the Mississippian Redwall Limestone. The karst Redwall surface was eventually covered by up to 900 meters of shallow marine to continental sediments ranging in age from Pennsylvanian to Triassic. The pipes were formed by progressive upward stoping caused by groundwater ascending under hydraulic head along near-vertical faults, joints and fractures. The stoping process involved both chemical disaggregation and mechanical failure of roof and wall rock. Upward stoping of successively younger units allowed for upward propagation of a pipe and resulted in a chimney-like column of breccia between the steep walls of the pipe. Syndepositional thickening of sedimentary units of varying ages indicates that pipe formation began as early as early Pennsylvanian time and continued intermittently through Triassic time.

Jan 1, 2007

By Thomas C. Shapiro

Introduction In recent years - even months - the number of articles on computers has increased rapidly. One can hardly pick up a newspaper or magazine without seeing a computer-related article. The article usually explains how the computer will change our lives. Many of us have some concern about the nature and type of change. For most of us, though, the problem is lack of information and understanding about how computers work. In other words, how do we make cost-effective decisions about computers? This three-part series will explain, simply, what a microcomputer is, how it works, and how to decide if you need one. This first article will define terms and briefly discuss areas where computerization might be economic. The second article will discuss geology and mining applications. The third article will discuss plant, administrative, and geotechnical areas as well as the future of software development in the minerals industry. Terms and Concepts All computers have input and output devices and a central processing unit (CPU). Information - instructions and data - is communicated to the computer by means of input devices. These instructions to the computer are converted into language that the computer understands. This causes the instructions to be carried out in the CPU. The result of these operations is translated back into language that we understand. This information is then sent to output devices such as printers and video display tubes. Traditionally, peripherals were devices separate from the main-frame (the CPU and memory) and were used to input, output, and store information or instructions. Today, peripherals perform the same functions though they may be housed in the same cabinet as the CPU and memory. Historically, peripherals included all input and output devices not part of the mainframe. Input devices include keyboards, magnetic tape, and card readers. Tapes and disks are input as well as output devices. Output devices are printers, CRTs (Cathode Ray Tubes), and any mass storage device capable of storing data when directed to do so by the computer or the program. In fact, any mass storage device that can give the computer data when requested is an input device. Mass storage devices include floppy disks (thin, round sheets of plastic covered by metal particles), and hard disks. The latter are thicker and more densely coated with metal particles. This allows much more information to be stored. Another type of mass storage is magnetic tape. Its type and size varies widely. Processing and Storage Any computer understanding must include how instructions and data are processed and stored. Information is stored as a positive or a negative field known as a "bit." There are eight bits in a byte. The bits can be represented as either a one or a zero. Thus the code for a byte representing the numeral one is 00110001. The byte representing the letter A is 01000001. These codes are from the American Standard Code for Information Interchange (ASCII). ASCII defines the standard set of characters including alpha, numeric, and special characters. The computer's memory has allocated locations where instructions as well as incoming information can be stored. All information and instructions are stored as binary numbers bit by bit - zeros and ones. The amount of data that can be stored is referred to as either thousands or millions of bits or bytes. The letter "K" is used to designate one thousand units. The letter "M" is used to mean one millon units (one meg). Disks Thus, a 113-mm (5 1/4-in.) floppy disk - double sided and double density (DSDD) - contains 320,000 bytes (characters) or 320K. This is about 164 double-spaced, type-

Jan 2, 1984

The occlusion of unliberated gold particles in silicates and sulfides in crushed/milled ore dictates the recovery that can be expected. The grade of this occluded gold in cyanide leach residues shows a consistent, general relationship to the head grade of the ore, irrespective of mineralogy or geographical location. The residue grade almost invariably increases with the head grade, but not in proportion to it. This phenomenon appears to stem from the nature of the geological events originally responsible for creating the ore deposits. A statistically-based technique for determining the true head grade-tail grade relationship from gold plant operating data is described. The effect is illustrated with results from several worldwide gold milling operations analyzed over the last 35 years.

Jan 1, 2008

By D. F. Scott

The purpose of this study was to determine if miners are at risk from exposures to chemicals used in the mining industry, and determine the nature and sources of the illnesses and injuries. The authors reviewed the Mine Safety and Health Administration?s (MSHA) Employment and Accident, Injury, and Illness database and identified 2,705 cases of chemical-related injuries and illnesses that were reported to MSHA from 1999-2006, involving 66 different chemicals. The main source (cause) of chemical-related cases was acids/alkalis (about 39%). The primary nature (effect) of chemical-related cases was chemical burns (about 57%). The job classification where workers incurred the most chemical-related injuries and illnesses was cleaning plant operator/media operator/boney preparation plant operator/crusher worker. The number of nonfatal days lost did not change significantly and overall, the incidence rate of chemical-related cases decreased by 36%. Chemical burns accounted for a large number of injuries; mining companies should carefully examine their personal protective equipment (PPE) requirements, training methods, and safety culture to insure that their workers are protected.

Jan 1, 2009

By William L. Husk

Stockpiles have always been a necessary part of coal mining except, perhaps, when a person was mining only for the needs of his family from a seam on his home place or coal mined for the use of a small hamlet and carried to each man's house as it was mined. Then it may have been stockpiled at each man's place for several days or on the village common. Mining with this limited production required waste stockpiling. Stockpiling of the products of coal mining, both coal and waste material, has always been a necessity. Very little coal has ever been moved directly or immediately from the working face to the point of consumption and burned. It has always been expedient to stockpile the coal some- where and store the waste.

Jan 1, 1981

By Kelvin K. Wu, George H. Gardner

On July 24, 2002, a nonfatal entrapment accident occurred at the Quecreek #1 Mine, Black Wolf Coal Company, when an active mining section inadvertently cut into a flooded abandoned mine. This incident, and the dramatic rescue which ensued, brought national attention to a common problem in the coal mining industry. Since 1995, there have been more than 100 inundations at coal mines in the United States. Unavailable, inaccurate, or incomplete mapping of older abandoned mines is typically responsible. Serious problems associated with accidental discharges of fluid mine waste material (slurry) and water from coal refuse disposal facilities have resulted from similar causes. Recent problems related to the inaccurate location of old abandoned mine works have increased the interest in the use of conventional and emerging drilling and geophysical techniques for detection of air-filled and water-filled cavities. The United States Congress has committed significant funding toward investigating the applicability of these technologies. MSHA actively promotes the use of the best available technology to minimize the significant adverse safety and environmental consequences associated with unplanned breakthroughs and inundations. This paper provides background information and a general summary of the MSHA-sponsored field demonstration projects which are currently in progress. Potential benefits and limitations are discussed. The need for field verification/ground-truthing is emphasized. Under appropriate conditions, geophysical methods can be effectively integrated into a comprehensive field exploration program.

Jan 1, 2005

By R. C. Ford, W. L. Niccoli, J. B. Finley

All mining operations are superimposed on natural hydrologic systems. As a result, mining operations are influenced by natural hydrologic processes and require water management systems to successfully conduct mining activities. Managing water and mining-related solutions is a critical task at all stages of the mine life because of the time-dependent nature of natural and mining-related flows. Effective operation of the mining water management system requires a “systems” approach that integrates the time-dependent effects of all water and mine solution handling components. This paper discusses the concept and application of dynamic systems modeling to address the time dependent nature of mining water management systems.

Jan 1, 2002

By A. Martikainen

Field tests concerning a fog mesh method for fog removal are discussed. The first tests were performed at the Pyhäsalmi Mine, Finland. As this study gave promising results, further studies were completed at the Orivesi Mine. The results of these most recent field tests are presented and the two studies are compared. The Orivesi test set consisted of four materials. These included air filter fabric, fibrous filter fabric, a plastic greenhouse mesh, and an aluminium mosquito net. The variation of the Orivesi results was more noticeable than what was found previously. The best fog removal effect of all tests was achieved with the aluminium mosquito net, while the plastic green-house mesh performed worst. The humidity reduction by aluminium net was more profound than any of its precedents. More mesh materials will be tested in the near future.

Jan 1, 2007

A glance at the accompanying table reveals that for the first time in many years the industrial minerals field did not post significant gains in production. Gypsum, cement, sand and gravel, and crushed stone production-which are very sensitive to construction industry performance-barely managed to stay even, or in fact, declined slightly. Even barite production, in spite of increased oil and gas drilling, was off 5% in 1979 from 1978. Domestic fluorspar production continued to decline while imports, primarily from Mexico, South Africa, and Spain, rose 11%. Worldwide production of iodine (which is used primarily as a catalyst, animal feed additive, and in ink and colorants, stabilizers, pharmaceuticals, photographic film, and disinfectants) grew about 9% on a worldwide basis-from 10.75 Tg to 11.16 Tg. This does not include US production. The two US producers increased demand as apparent domestic production increased about 5%. Increasing energy costs and the transportation situation have had a prohibitive effect on the industrial minerals field. The critical shortage of railroad cars, according to consultant Neil Johnson, is due to several factors: • High capital investment rind interest rates needed to build new equipment, • Accidents, obsolescence, and failure to repair equipment reduced car availability, •Reduction in some train schedules due to fuel economy, and •Increased turnaround time as a result of new safety regulations. Railroad rates have increased an average of 7% per year for the past 10 years. Last year's increases were about 11.1% due to fuel costs and surcharges. Truck shipments have increased their penetration in certain areas of the southeast because of the shortage of box cars and the producers' demand for quick shipment. Some producers report a 15-20% increase in truck use. In the feldspar-mica area, which formerly made most shipments by rail, trucks are now used for about half the shipments. Marketing prices, as expected, increased due to higher costs for energy, power, labor, and supplies used in production. Estimated average price increases were about 10% which, in many cases, did not cover increased production costs. These factors-rising energy costs and the critical transportation situation-resulted in an unsatisfactory year for industrial minerals. Stanley J. Lefond Cnntrihuting Editor

Jan 5, 1980

By William W. Edgerton, Calvin Locke

INTRODUCTION King County, Washington operates a regions wastewater treatment system that provides treatment to 18 cities and 16 sewer districts in the greater Seattle metropolitan area. The system serves 1.4 million people and currently includes two regional treatment plants. In 1999, a long-range planning study identified the need for a third regional treatment plant, now known as Brightwater. Prior to this project, the county has almost exclusively used the traditional design-bid-build delivery process for its capital projects. However, with the adoption of the RWSP, the county began to study the potential application of innovative project delivery methods. This paper looks at the project delivery methods used for the Brightwater project, based on the specific needs of this large, complex, and multi-faceted project. THE KING COUNTY WASTEWATER TREATMENT SYSTEM In 1958, voters approved the formation of a regional agency called the Municipality of Metropolitan Seattle, or Metro, to build and operate a regional wastewater collection and treatment system. Prior to the formation of Metro, there were no regional wastewater treatment facilities and pollution of Lake Washington and Puget Sound from untreated sewage was a concern for many residents. In 1994, King County merged with Metro. The county’s 1,087 square kilometer (420 square miles) wastewater service area covers most of urban King County and extends into portions of two neighboring counties. The system includes two regional treatment plants, a local plant, 61 pump and regulator stations, and 571 kilometers (355 miles) of conveyance pipeline which convey wastewater from local districts to the treatment plants. As with other areas, the greater Seattle/King County region has seen rapid population growth. The RWSP estimates that the current system would soon reach capacity, and called for the construction of a new third regional treatment plant, called Brightwater, to be operational by 2010.

Jan 1, 2005

By S. Suwansawat, D. J. Maconochie, C. C. Chang

This paper describes the overall delivery of the tunneling for the Mass Rapid Transit Authority of Thailand’s Chaloem Ratchamongkhon Line in Bangkok and the constraints provided by the alignment. Eight earth pressure balance tunnel boring machines were employed under two major civil works contracts to drive approximately33 kilometers of tunnel in soft saturated ground beneath the crowded streets of Bangkok. Responsibility within the contract for building damage provided an inherent control for ground movement arising form tunneling when the right of way was narrower than the influence zone. These limits affect the earth pressure balance requirements and permissible ground loss. The methods adopted to limit ground movements and deal with the various obstacles to tunneling influenced the design and operation of the machines. The challenges provided by the need to tunnel through numerous lines of piled foundations of canal bridges and overpasses crossing the alignment are described.

Jan 1, 2001

By L. K. Marshall

The importance of high quality underground mine ventilation is readily apparent. The principles of primary and auxiliary mine ventilation, however, are sometimes less readily apparent. The first article in this two-part series discusses some general aspects of primary and auxiliary ventilation. Next month's article will detail considerations involved with auxiliary mine ventilation.

Jan 1, 1982

By A. E. Koski

Two of the largest industries in northern Michigan, pulp and paper manufacturing and iron mining, formed a mutually beneficial partnership and collaborative research program to utilize paper mill residuals for waste rock stockpile reclamation. Historically, the majority of the paper industry’s residuals have been disposed of in landfills. The beneficial use of paper mill residuals for mine reclamation provides an environmentally sound recycling solution for the solids generated at northern Michigan paper mills and eliminates the need to strip additional overburden (glacial till) for final mine reclamation. Residuals offer a cost-effective source of organics and nutrients necessary for successful reclamation and waste rock stockpiles offer an economical and environmentally sound solution for disposal of residuals. The goal is to successfully pioneer technical development of paper mill residuals to accomplish vegetation of steep waste rock stockpile slopes and benches to establish a self-sustaining plant community that meets final reclamation requirements. Of the various types of iron mining wastes, rock stockpiles pose the greatest reclamation challenge. Success depends on incorporating sufficient organic matter into the rock stockpiles to produce a growth medium that can sustain vegetation without the need of overburden. This is an ongoing research program that is evolutionary in nature with numerous field trials, greenhouse studies, data collection and monitoring over multiple growing seasons. The program is a combination of innovative ideas and accepted reclamation practices that is proving to be a beneficial and economic approach to paper mill residual management and mine reclamation that will eventually lead from research to standardized reclamation procedures.

Jan 1, 2006

By F. B. Henderson

1.0 PROLOG Since the "end" of the Cold War, revolutionary new research and commercial remote sensing capabilities are being developed that will dramatically change the way we map the earth and address its environmental problems. The technology challenge is not the growth of new environmental remote sensing technologies themselves. It is, rather, how these new innovative observing systems can be accepted and used to the benefit of both the regulatory and the mining communities in the light of present concerns about unknown risks of discovery and liability. The basis for this paper is an unpublished technology primer prepared for the industry-government Workshop on Advanced Measurement and Site Characterization for Mining Impacts held at Colorado School of Mines, Golden, Colorado, July 14-17, 1997

Jan 1, 1999

By R. Oler

The need for yieldable ground support, particularly in high stress or deep mining conditions, has grown in recent years. This paper highlights some of the current industry limitations and provides selection criteria for a new yielding ground support system, DSI?s Dynatork Bolt. This bolt distinguishes itself by withstanding 16 ? 30 kJ of energy deflecting loads anywhere from 7 ? 20 tons (depending on the energy). A summary of the laboratory test results and case studies will also be presented as a measure of the performance of this dynamic product.

Jan 1, 2012