Search Documents

By K. Blaski

his paper reports an investigation aimed at optimizing the compaction of granulated hard-metal powder for the production of cutting tool inserts. The optimal compaction is that which yields optimal shrinkage during sintering, i.e. minimum porosity in the sintered part. Extensive compaction tests on 23 different hard-metal powders have been carried out and have shown that the ideal ?green density? of a hard-metal compact, i.e. the density after compaction, increases linearly with the apparent density of the powder. On the basis of this result, an equation has been derived, which allows one to predict the optimal shrinkage that a hard-metal compact undergoes during sintering once the following data are known: the required sintered density, the volatile content of the powder and the apparent density of the powder. Since these data are available to the tooling designer, this equation allows one to design tooling for the compaction of hard-metal, which leads to optimal shrinkage

Jan 1, 2007

By C. C. Oosthuizen

Paper written on project work carried out in partial fulfilment of Technikon Practical Training Frank shaft is mining both Merensky reef and UG2 reef. The Merensky orebody is almost depleted and this was the reason for starting to mine the UG2 ore reserves. It was decided to mine the UG2 orebody with trackless equipment using a bord and pillar mining method. Frank shaft has been mining the UG2 orebody for nearly 5 years. The T-cut mining method was introduced to see if it could improve the grade of the run of mine (ROM) as well the extraction percentage.

Jan 1, 2005

By P.J. Terbrugge

Open pit slope design has conventionally been effected as a bottom-up function utilizing available geotechnical information. This results in a decision criterion based on probability of failure and factor of Safety with a risk assessment being carried out on the proposed design slopes. The design approach recommended reverses the process using fault event tree decision methodology. The consequences of this approach are that acceptable risk criteria have to be determined by mine owners. Slopes are then designed by the technical staff to achieve these corporate goals. Benefits that arise from the process are that the owners take a proactive decision on the risk-benefit relationship allowing the technical staff to optimize the geotechnical exploration programme and design.

Jan 1, 2006

By H. F. Fuls

The quality of Pregnant Leach Solution (PLS) at Skorpion Zinc is of utmost importance for efficient operation of the Solvent Extraction (SX) Plant. Suspended solids in the PLS forms CRUD in the settlers, resulting in reduced zinc transfer capacity and increased impurity carry over to Electrowinning. The Ishigaki Fibre-Wakishimizu filter (fibre media rapid filtration equipment) has been identified as polishing filter that potentially could remove solids from the PLS of Skorpion Zinc. A pilot unit with 20m³/h capacity was tested on site over a period of 9 months under plant operating conditions in the refinery. The FW filter produces a clear filtrate, acceptable for the Solvent Extraction. Turbidity is improved by 72%. Gravimetric analysis indicates a 47% removal of solids. However, the gravimetric method is biased by a co-precipitation of saturated salts during the analysis. Filter media is blinded by the Skorpion Zinc PLS solution, as result of suspended solids and process chemistry. The media could not be regenerated to acceptable conditions. Further testwork to investigate the impact of process solution chemistry modification on blinding is undertaken. Based on the outcome of this investigation a final decision on the FW filter can be taken.

Jan 1, 2008

A single aggregate mix design was developed based on a slag/Portland binder blend and crusher sand. The primary design criterion, after performance, was the fluidity of the shotcrete and concrete product to ensure compatibility with existing manufacturing and shotcrete equipment as well as the pipeline transport system Cullinan Diamond Mine was investigating. Initial work had determined an optimum slag/Portland to aggregate ratio while retaining a water to slag/Portland binder ratio of approximately 0.4 to maintain the flowability of the product. A super-plasticizer was used to further increase the flowability of the product as opposed to increasing the water content. Finally a polypropylene reinforcement fibre was included in the wet shotcrete product to improve the energy absorption characteristics of the shotcrete. Previous work on the strength development of the slag/Portland based shotcretes and concretes suggests that strength class based on the EN 206 specification is C40/50 while the toughness classification based on the EFNARC plate test is c, or greater than 1000 joules1. Typically, Cullinan Diamond Mine wanted a shotcrete with a uniaxial compressive cube strength of 45 MPa and an energy absorption, based on the EFNARC plate test, in excess of 700 joules. This is an EN 206 strength class of C36/45 requiring a uniaxial compressive core strength of 30.5 MPa and a toughness classification of b1. In addition to the shotcrete development, Cullinan Diamond Mine required concrete products with a compressive strength range of between 25 and 60 Mpa for differing construction operations underground to be manufactured from the same mix design and raw materials as for the shotcrete. Finally, Cullinan Diamond Mine carries out extensive dry shotcrete operations and an investigation into the possibility of using the single aggregate mix design for dry shotcreting was also entered into. This paper presents data that indicates that, under the terms of reference, a wet and dry shotcrete and concrete product appears to be possible from a single aggregate less than 6.7 mm in size, and that a slag/Portland binder is suitable for use as the hydraulic binder in all the products, and that the necessary performance parameters of strength and energy absorption can be achieved.

Jan 1, 2006

By R. Scott

This article describes and evaluates the establishment of Kuyasa Mining including the search for a suitable deposit, the ongoing lack of finance, and market constraints. Despite the dramatic initial growth and success of their Ikhwezi Colliery near Delmas, Mpumalanga, Kuyasa?s experiences offer some sobering arguments for significant changes to mineral rights ownership, the attitude of financial institutions and government policy if South Africa is to have a dynamic and successful junior and small-scale mining sector.

Jan 1, 1998

By R. P. Mohring

Before we look at what the challenges and opportunities for future coal mining will be, it is appropriate to have a look at whether there will be a coal industry in the future. There is much talk about the damage caused by the burning of fossil fuels and the need to replace coal and oil with more environmentally friendly energy sources. Yes, there is evidence that the current practice in burning of fossil fuel has certain negative environmental effects, however, the adverse effects for global economic development from inappropriate measures to control greenhouse gas emissions would be severe.

Jan 1, 2001

By M. D. Lionnet

The Bafokeng Rasimone Platinum Mine (BRPM) is a joint venture between Rustenburg Platinum Mines Limited and Royal Bafokeng Resources (Pty) Ltd (Bafokeng). The mining lease has been granted over Boschkoppie 104JQ and is located approximately 10 km south of the Pilanesberg Alkaline Complex. The Merensky Reef, which constitutes the principal orebody, is geologically complex. A relationship between its geological variability and the associated mineralization has been established by defining a number of facies types. The Merensky Reef has been subdivided into seven distinct facies types: the pegmatoidal facies, contact facies, FW1 potholefacies, FW3 pothole facies, FW6 pothole facies, and FW7 pothole facies. The Merensky Reef, which does not form part of the potholed reef, has a large component of footwall mineralization. The pothole facies, in contrast, has mineralization located in the hangingwall. Statistical analysis of the facies types indicates that they are unique populations and hence need to be evaluated independently. The mining lease has distinct structural domains that have added additional complications to evaluation of the Merensky Reef. The Merensky facies on BRPM exhibit unique geological and statistical characteristics within well-defined structural blocks. Due to the extreme variability of the Merensky Reef on BRPM a unique approach has been developed, within Anglo Platinum, to evaluate the deposit. Mining cuts are defined and composited for the individual facies types, and then modelled individually by applying known geological controls. The resultant grade models are weighted based on statistical and local geological knowledge. The object of weighting the facies is to replicate the variability observed in the orebody. The introduction of stringent geological controls to the evaluation process has resulted in increased confidence in the in situ grades estimated as an input to the mine planning process.

Jan 1, 2007

By J. Golamnejad

This paper attempts to model long-term production scheduling problems by chance constrained binary integer programming in a stochastic environment. This stochastic model is set up to account for ore block grade uncertainty. The probability distribution function of grade in each block is used as a stochastic input to the optimization model. This distribution function in each block should be determined using a Geostatistical Simulation approach. The deterministic equivalents of these chance constraints are then achieved, which are in the form of nonlinear in binary variables. A confidence level at which it is desired that the uncertain constraints holds, is specified in each scheduling period. Rather than the previous risk-based model, this formulation will yield schedules with a high chance of achieving planned production targets while maximizes the expectation of net present value and minimizing the variance function simultaneously. Using this method, the grade uncertainty is integrated explicitly into the optimization process.

Jan 1, 2006

By P. S. Paul

Mine accidents/injuries are complex and generally characterized by several factors, from technical to social characteristics. In this paper, a sociotechnical model for work injury in mines was developed and tested through structural equation modelling with application to case study mines in India. In total 14 variables were considered in this study. Most of the variables are not directly quantifiable. Instruments were developed to quantify them through a questionnaire survey. Underground mineworkers were randomly selected for the survey. Responses of 300 participants were used for the analysis. The analysis was conducted in three parts. Firstly, high-low plots were constructed to explore the variations in responses to the questionnaires by the accident involved (AG) and non-involved (NAG) workers. Secondly, a t-test was conducted to see whether the responses were significantly different for the two groups or not. The chi-square results showed significant differences of responses among the two groups. Finally, how these difference scan cause accidents/injuries in mines was hypothesized and evaluated using structural equation modelling. The measurement model of the Linear Structural Relations (LISREL) program was used to identify the latent constructs of the sociotechnical model. The structural model of LISREL was used to estimate the interrelationships among the constructs. The case study results showed that there is a sequential interaction among the sociotechnical factors leading to accidents/injuries in mines. Work hazards induce more job stress in the workers while social support mitigates the same. Job stress and safety environment predict the workers? job involvement. A worker who is more job-involved exhibits better safety performance, which in turn reduces work injury. The safety environment is shown to have a direct mitigating effect on work-related injury. The findings of this study clearly revealed that job stress and safety environment are the two key factors influencing work-related injuries in mines that need to be addressed properly through effective safety programmes.

Jan 1, 2005

By M. Grodner

Underground excavations exhibit different hangingwall conditions in response to varying geotechnical and mining situations. These differences need to be quantified so as to accurately determine the effectiveness of the mining and/or support strategies. A useful tool for the quantification of these differences is hangingwall profiling. Two methods of hangingwall profile measurement are described?termed irregular and periodic methods. Several data analysis techniques are reviewed for these methods and the suitable ones are discussed in detail. For irregular data the suitable techniques are the determination of the length, the average of the profile and the average absolute deviation from the mean of the profile. All of these techniques as well as determination of the moving average of the height and examination of the spectral image of the profile can be successfully applied to regular data. The effect of preconditioning on the hangingwall is discussed as an example and it is quantitatively shown that it results in improvements of conditions. The techniques described allow the engineer to quantitatively identify the appropriate support type or mining strategy and thus represent a valuable decision-making tool. It is suggested that these techniques should be employed on a routine basis by the rock engineers on the mines as part of their geotechnical classification, as well as support manufacturers to quantify the effectiveness of various support types.

Jan 1, 2000

In surface mining operations, ultra-heavy trucks operate on haul road networks which are typically from 10?40 km in length. These road networks are often not optimally designed and maintained and as a result, identifying and remediating road functional defects is problematic. Most surface mine operators agree good roads are desirable, but find it difficult to translate this into an effective road maintenance system. This paper presents a haul road maintenance management system which utilizes an assessment of rolling resistance based on a functional performance evaluation of a haul road, together with mine haul truck operating cost models to derive the optimal frequency of road maintenance. A typical application is presented which illustrates the potential of the technique to manage maintenance as and where needed with resultant reduction in total road user costs and an improvement in service provided for the road user. Keywords: Haul road, surface mining, road maintenance, transportation, pavement design

Jan 1, 2003

By D. J. Greeff

By making use of genetic programming, empirical models for metallurgical processes can be evolved that are more cost-effective than models determined by means of classical statistical techniques. These methods explore populations of candidate models assembled from sets of variables, parameters and simple mathematical operators, and do not require explicit specification of model structures. The application of the proposed strategies is illustrated by means of a case study pertaining to the leaching of nickeliferous chromite ores. Modelling of the nickel and cobalt extraction from the ores yielded models of similar accuracy compared to those obtained by non-linear regression and artificial neural networks. However, in the case of the iron extraction from the ores, the genetic programming model was significantly more accurate than both the regression and neutral network models.

Jan 1, 1998

By B. McCosker

The choice of the appropriate delivery process for a project is often not adequately thought about. The industry needs to be prepared to break its preconceived mind-sets on delivery procedures. Industry should also be prepared, on a project by project basis, to commit to a critical review as to how the assessment and then selection of the best procurement method can best optimize the project outcome for both client and contractor. Conventional standards and biased reliances and experienced based preferences should be challenged. To achieve this requires a paradigm shift in attitude to both the process of tendering and the evaluation of tenders. Tender and contracting practices are dynamic and have moved away from solely cost based assessments. Tendering contracts arise imposing changed duties upon owners. Traditional contract delivery models have shifted, reflected in part by the trend towards relationship contracting. The categories of contract options are not closed. Many are but hybrids of other time-tested models. This paper considers options available for any brownfield or greenfield project. The principles outlined are translatable to supply, upgrade, operation and maintenance arrangements.

Jan 1, 2002

By G. Hangone

Paper written on project work carried out in partial fulfilment of MSc thesis This paper investigates the effects of thiol collectors: xanthates, dithiophosphates, dithiocarbamates and mixtures of these on the froth flotation performance obtained with a bornite-rich copper sulphide ore from Okiep Copper Mine with a feed grade of 1.8%copper. Batch flotation tests were used to assess the performance in terms of mass-water recovery, sulphur grade-recovery and copper grade-recovery relationships and the Klimpel rate constant for copper recovery. The results showed that the di-ethyl-dithiocar-bamate (di C2-DTC) was the weakest collector of copper sulphide minerals. Highest copper recoveries were obtained with the di-ethyl-dithiophosphate (di C2-DTP), which were accompanied with more watery froths and lower copper grades demonstrating frothing properties in addition to collector action. Superior copper recoveries were obtained with the 90% ethyl xanthate (C2-X):10% di-ethyl-dithiophosphate (di C2-DTP) and 90% ethyl xanthate (C2-X):10%di-ethyl-dithiocarbamate (di C2-DTC) collector mixtures compared to that obtained with ethyl xanthate at an equivalent collector dosage of 0.139 mol/ton ore (a dosage equivalent to 20 g sodium ethyl xanthate per ton ore). A superior copper grade was obtained with the 90% ethyl xanthate: 10% di-ethyl-dithiocarbamate collector mixture at a dosage of 0.0695 mol/ton ore compared to that obtained with ethyl xanthate at the same equivalent dosage. Keywords: flotation, collector mixtures, copper sulphide ore

Jan 1, 2005

By F. Sawyerr

A bubble population balance model is proposed for the prediction of Sauter mean bubble diameters in mechanical flotation cells. In the model, the flotation cell is treated as two separate, statistically homogeneous zones?the impeller zone, and the bulk tank zone. Balance functions for the rates of bubble breakage, coalescence, recirculation and inlet-outlet events are proposed based on classical chemical engineering research in two- and three-phase fluid mixing systems. An initial simulation of the population balance model shows trends in bubble size distributions comparable to measured distributions in industrial mechanical flotation cells.

Jan 1, 1998

By M. Kumral

Raw material fed into a processing or refining plant is required to be uniform in composition for several reasons. When the mined ore is highly variable in quality the only way to ensure consistency is to homogenize the ore prior to the process. The problem is more complicated in the case of multiple ore sources. The idea behind the research is that theoretical blending ratios can serve not only to meet predefined specific criteria but also to reduce grade fluctuations of variables under consideration. In this paper, the problem is formulated as a quadratic programming problem, whose objective function is in quadratic form and constraints are linear. A case study was conducted on a data set from an iron orebody to demonstrate the technique. The objective was to minimize the blend variability in terms of each variable (in this study, iron, silica, alumina and lime) grade of ores extracted in three different production faces. The stockpile capacity, lower and upper limits of each variable satisfying operational requirements and non-negativity were constrained to the model. A modified simplex method developed by Wolfe was used for solving the blending and homogenization problem. The promising results can be used as apart of the stacking and reclaiming design. Keywords: blending and homogenization problem, quadratic programming, Wolfe method.

Jan 1, 2005

By L. P. Lamprecht

Traditionally, South African shaft sinking operations have used electric detonators for the initiation of blastholes. Globally, the trend in shaft sinking is to use the shock tube and detonating cord (STDC) initiation system, with value adding benefits. In pursuing this global trend, Cementation Mining of South Africa in partnership with SMX have ventured the STDC route. This paper explores the work carried out to date, and identifies a number of benefits to be gained by using the system.

Jan 1, 1999

By A. Varadarajan, M. Hashemi, K. G. Sharma

Quartz mica schist collected from Nathpa-Jhakri Hydropower Project, Himachal Pradesh, North India is tested under triaxial loading using a servo-controlled loading system. Complete stress-strain-volume change behaviour including post peak softening behaviour of the samples, are presented. Strength and deformation parameters are given. Quarz mica schist, der von Nathpa Jhakri Hydropower Projekt, Himachal Pradesh gesammelt wird, wird Nördlich Indien unter triaxial geprüft, der von Gebrauch eines servo kontrollierten Ladesystems beladung. Vollständiges Spannung-Spannung-Band Änderung Verhalten Postens Spitze Erweichung Verhaltens der Proben, wird überreicht. Kraft und Verformung Parameter werden gegeben. Mica à quartz schist recueilli du Projet de Hydropower de Nathpa Jhakri, Himachal Pradesh, l'Inde du nord est essayé sous l'utilisation de chargement de triaxial un système chargeant servo réglé. La tension complète-la tension-comportement de changement de volume y compris la poste sommet amollir le comportement des échantillons, sont présenté. Les paramètres de force et déformation sont donnés.

Jan 1, 2003

By R. M. Jara

This work evaluates and characterizes the impact of the support size and mining dilution of a block model in the operation and selection of equipment at an open pit mine. An exploratory analysis and geostatistical modelling of the grades assayed on a set of drill hole samples is performed, which allows constructing a grade model on a dense grid by means of a conditional simulation. The grades are then averaged to greater selective mining unit supports in order to proceed with the study and methodology. First, the metal-tonnage curves are used to analyse the loss of selectivity on the in situ resources caused by a change of support. Concerning the ore reserves and their mining sequence, defined in the pit optimization and analysis process, the same curves prove that the loss of selectivity is more accentuated. Second, the importance of the block boundary dilution produced during mining operations is assessed. Its value depends on the amount of ore in contact with waste, on the loading error of the equipment and on the ore loss/waste dilution criterion assumed by the planner. The dilution percentage and the differences between waste and ore grades become higher when the block size decreases. For these reasons, considering the dilution in the production plans makes mining a small support more constraining. An adequate delimitation of the orebody can improve the mining selectivity, leading to greater income. Finally, a study of the increase in mining cost that provides a zero difference in NPV between the different block size options is carried out, in order to determine the maximum increase in mining costs for which it remains profitable to mine at a smaller block size. Keywords: Mining selectivity, support effect, block boundary dilution, selective mining unit size, block model.

Jan 1, 2006