Search Documents

By A. D. Pienaar

The aqueous chemistry of niobium and tantalum compounds with hydrofluoric acid is a mature field of investigation. In contrast, very little attention has been paid to reactions of these compounds in non-aqueous environments. Similarly, reactions of elemental fluorine with niobium and tantalum compounds have received little more than cursory attention in literature. This work discusses the isothermal reaction kinetics derived from thermogravimetry, using a less redundant approach than is currently the standard. We also discuss the most likely kinetic models for this reaction.

Jan 1, 2012

By Richard Peaker, Jens Lichter, Alexander V. Potapov

The recent combination of Computational Fluid Dynamics (CFD) and Discrete Element Modeling (DEM) can provide considerable insight into the performance of flotation cells. One area of interest from a fundamental equipment design perspective has been the influence of flotation cell size and the inflow rate on the metallurgical performance of the cell. One of the specific design objectives when increasing the size of flotation cells, or increasing the feed flow to the flotation cell, is to ensure that the feed stream flowing into the cell does not have an opportunity to bypass the mechanism. This paper describes the initial modeling efforts to quantify the inter-relationship of cell size, inflow rates, and feed and discharge box placement, on the retention time distribution of solids in the flotation cell, and the fraction of particles that bypass the mechanism on a size by size basis.

Jan 1, 2007

By C. Scheffer

This paper describes a model that can simulate the behaviour of a pneumatic intensifier that is generally referred to as an ?air pump? (AP). The AP is used in many South African underground mines, and utilizes compressed air with pressures between 0.3?0.6 MPa to pump water up to pressures of 12?18 MPa. The high pressure water is used in numerous underground mines to pressurize props and roof bolts that act as safety and roof support devices. The simulation model reproduces the intensifier's operation under various conditions and therefore can be used to investigate the AP's sensitivity towards environmental conditions, design parameters (such as spring stiffness, plunger diameter, nozzle diameter etc.) and operating conditions. Model validation by comparison with laboratory experiments showed good correlation. The model can subsequently be used to investigate design changes aimed at improving the AP's performance and reliability over a wider range of operating conditions.

Jan 1, 2005

By J. Searra, M. Aboagye

"For new mining projects or for medium- to long-term areas of existing mines, drilling data is invariably on a relatively large grid. Direct estimates for selective mining units (SMUs), and also for much larger block units, will then be smoothed due to the information effects and the high error variance.The difficulty is that ultimately, during mining, selection will be done on the basis of SMUs on the final close-spaced data grid (grade control), which will then be available, i.e. the actual selection will be more efficient, with fewer misclassifications. However, this ultimate mining position is unknown at the project feasibility stage and therefore has to be estimated. This estimation is required because any cash flow calculations made on the basis of the smoothed estimates will obviously misrepresent the overall economic value of the project, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the average grade of the orebody. Similarly, unsmoothed estimates will be conditionally biased and will give even worse results, particularly in local areas of short- and medium-term planning or mining.This paper presents a case study of indirect post-processing and proportional modelling of recoverable resources designed for mediumand long-term mine planning at the Gold Fields’ Tarkwa Mine in Ghana. The case study compares long-term indirect recoverable mineral resource estimates based on typical widely spaced feasibility data to the corresponding production grade control model as well as the mine production. The paper also proposes certain critical regression slope and kriging efficiency control limits to avoid inefficient medium- to longterm recoverable estimates, and highlights the danger of accepting block estimates that have a slope of regression less than 0.5."

Jan 1, 2015

By P. A. Lilly, W. Sarunic

In most cases, slope movement monitoring data are collected on a temporal basis and displacement or velocity is plotted against time in order to assist the engineer to make judgements about slope behaviour. Once an unusual behaviour pattern has been established, the data are then analysed to estimate when the key inflection points occur in the data, when the slope movements start to accelerate and, ultimately, when the slope is expected to collapse. The identification of these inflection points is sometimes difficult to achieve with the naked eye. This paper presents the application of a trend analysis technique, known as cusums, to assist in this process. The authors have presented a range of data from various real life examples which highlight the effectiveness of the cusums technique. A key aspect of the cusums technique is the use of a constant (K) against which data trends are assessed. This constant is best derived from slope performance data at each site, as each rock mass will behave in its own unique way. The authors have experienced slopes that have had threshold values ranging from 0.1mm/day through to 10mm/day, and therefore a conservative approach should be adopted when assessing the performance of slopes.

Jan 1, 2006

By N. Sano

The chromium oxide in stainless steel slags usually exists as Cr2O3. However, there is a possibility that it is oxidized to hazardous CrO3 after disposal or during use. Therefore, some technical developments to reduce chromium oxide by using a smelting reduction technique have been reported recently. This paper describes the fundamentals of the technique which have been applied to ferrochromium production and reviews the recent results in literature.

Jan 1, 2004

By Gift Chisakuta, Bravo Mbao, Nils Schwarz, Angus Feather, Anthony Mukutuma

Bwana Mkubwa is a 50 000 tons per annum copper cathode producer, owned by First Quantum Minerals and located in Ndola, on the Zambian Copperbelt. The Bwana Mkubwa solvent-extraction circuit was started up in 1997. In 2002, the plant began treating ore from First Quantum?s Lonshi mine located in the Democratic Republic of Congo. The Lonshi ore is exceptionally fine and the amount of solids in the feed solution reporting to the solvent-extraction feed solution increased dramatically. Initially, crud was filtered in a filter press, but this rapidly blinded and seldom produced anything better than a wet sludge containing large quantities of organic. In December 2003 the decision was made to install a Flottweg Z4E-3/441 Tricanter® centrifuge to recover organic from the crud. The installation was completed in June 2004 and has since led to significant improvements in plant operability and savings in organic consumption.

Jan 1, 2007

By A van Jaarsveld

Environmentally-friendly, safe and cost-effective technology for stope drilling has successfully been introduced at TauTona mine. It has enabled the problem of inadequate compressed air pressure and its downgrading impact on production capability to be overcome. The paper traces the development process which culminated in the conversion of the entire stoping operation at TauTona to electric drilling. Background work which took place at other mines is also described. Statistics of performance improvements are provided. 1. Introduction Holman?s Silver series and the Seco S215 were drills that had a measurable impact on the South African gold mining industry. It is too soon to say whether Hilti will join those great names. However, there is no doubt that the introduction of electric drills into the harsh and unforgiving world of deep level gold mining is a significant development. History has shown that being the first to enter a new technology is no guarantee of long-term success. The pain and suffering which accompany the birth of anything new can deplete the energy of the innovator while at the same time creating opportunities for competitors to leapfrog him. In addition to commitment and enthusiasm, the innovator must therefore also possess, or have access to stamina and resourcefulness to overcome the unexpected difficulties which will inevitably arise. All of these were needed for the Hilti project.

Jan 1, 2008

By C. J. Van Niekerk

The study comprised of the investigation into the sensitization characteristics of AISI 409 titanium stabilized ferritic stainless steel during low heat input welding. AISI 409 is a fully ferritic stainless steel used in catalytic converters and tubing for automotive exhaust systems due to the supposition that sensitization does not occur during low heat input welding. Two plates of 2 and 4 mm were tested for sensitization during low heat input welding. The study confirmed that chromium carbide (M23C6) precipitation occurs on the grain boundaries in the heat-affected zone with consequent depletion of Cr adjacent to the grain boundaries during welding. In the 2 mm plate sensitization occurred in the heat input range of 0.1 kJ/mm to above 0.25 kJ/mm and in the 4 mm plate sensitization occurred in the heat input range of 0.2 to 0.9 kJ/mm. Ti stabilization is ineffective at the heat inputs used in this investigation due to the rapid cooling rate through the temperature region where TiC precipitates. The presence of N was found to be detrimental since it consumes Ti on cooling, forming TiN, effectively lowering the amount of Ti available for TiC formation during rapid cooling after welding. Annealing for 5 minutes at 725°C does not improve the sensitization characteristics of the welded plate. There is a linear increase in grain size as heat input increases. The resistance to pitting corrosion decreases in the sensitized, welded plate in theheat-affected zone adjacent to the fusion line of welding. Keywords AISI 409 ferritic stainless steel, sensitization, grain growth, resistance to pitting corrosion, low heat input welding.

Jan 1, 2011

By M. Stephton, L. A. Cornish, R. Süss, N. B. Maledi, J. H. Potgieter, L. Chown

In today?s gas turbines, the emphasis is on saving energy and reducing the amounts of pollutants emitted. This can be attained only by designing alloys with higher melting points and the capability to retain mechanical integrity at increased temperatures. The development of nickel-based superalloys (NBSAs) has reached its limit, as the alloys are operating at critical temperatures close to their melting points. Further increase in the operating temperatures will result in dissolution of the strengthening phases and even melting. Recent trends are towards developing materials that are adequately strong but have much higher melting points and corrosion resistance than the NBSAs that are currently in use. Studies conducted on Pt alloys with similar structure to the NBSAs have presented mechanical results that are promising. This has led to further development of these alloys as a replacement for NBSAs. The operations of gas turbines are usually limited by hot corrosion, which could lead to catastrophic failures. Increased temperatures have an adverse effect on the corrosion of the alloys by making the environment more aggressive. Hence, during a material selection process, the corrosion behaviour of any selected material for a highly specialized application such as gas turbines needs to be assessed. Generally, coatings are applied to combat degradation by salt deposits, hence coated and uncoated NBSAs were selected as benchmark alloys. Corrosion mechanisms and kinetic studies of the Pt alloys were conducted. High temperature hot corrosion (HTHC) tests were conducted at 950°C for540 hours. Analysis of the corrosion products was conducted using a Raman spectrometer, scanning electron microscope with energy dispersive X-ray spectroscopy (EDS) optical microscopy, and X-ray diffraction study of the phases that formed. Both coated and uncoated NBSAs failed under the test conditions. Samples were covered with a porous non-adherent greenish layer which is characteristic of NiO. Pt alloys displayed superior corrosion properties compared with the benchmark alloys.

Jan 1, 2006

By Martin Banda, Gift C. Chisakuta, Moses Chabinga

KCM made a major modification to the Nchanga Tailings Leach Plant (TLP) changing the circuit from feeding post leach thickeners in parallel with leach discharge for solid ?liquid separation to a Counter Current Decantation (CCD) configuration utilising most of the existing equipment. The new circuit is aimed at improving copper recovery from approximately 70% to 79% through enhanced wash efficiency. The re-introduction of CCD circuit at elevated throughput of 46 000-tpd design was made possible due to the EIMCO E-Duc technology design which is an auto-dilution system that enhances solids settling rate. Commissioning (manual operation) which accommodated on-going operational requirements was phased and completed in January 2004. The circuit stabilised in subsequent months and in March alone an all time record copper recovery of 81.8% was achieved which contributed an extra 779 tonnes copper above the plant?s projected production plans. 100% of the project cost was paid back by end of April 2004 This paper discusses the work involved and the challenges faced during the re-commission

Jan 1, 2005

By W. A. Gericke, B. Olmstead, I. Mc Dougall, C. F. R. Smith

A finite element model was generated of a Søderberg electrode in a ferromanganese smelter. In this model, the casing and fins were modelled explicitly, and temperature-dependent material properties were included. A two-stage analysis procedure was used, the first part being a coupled thermal-electrical analysis using an applied DC current. As the casing material was non-magnetic, the DC current was deemed sufficiently accurate for this initial analysis. The proximity effect was not considered. Thermal boundary conditions based on assumed temperature distributions in the furnace were applied. Calculated temperatures agreed well with measured values. The joule heat calculated in this step was applied as a load to a coupled thermalstress analysis. The model was applied to a comparative study of alternative materials for the casing and fins. A number of different combinations of materials for the casing and fins were evaluated in a comparative study. The position of the baking zone was used as the criterion for evaluating the potential of each material combination. Based on this analysis, some material combinations were discarded as being entirely unsuitable, whilst the two most suitable combinations will be tested experimentally in the furnace. The stress analysis was performed on the most suitable option. The practical advantage of this analysis was that a number of what-if scenarios could be evaluated and discarded prior to embarking on expensive experimental work, thus limiting the amount of experimental effort required. A mathematical model allows for the comparison of options under controlled conditions, where parameters of interest can be varied individually, with all other parameters remaining the same, a condition which is difficult to achieve in an operating furnace.

Jan 1, 2004

By K. Y. Lee, J. M. Park, C. W. Park

Laboratory-scale experiments were carried out to investigate the effect of ladle slag composition on the decreasing behaviour of aluminum content in steel, i.e., reoxidation of molten steel in contact with slag, using a vertical tube furnace. The steel composition and the slag system chosen were for ultra low carbon and CaO-Al2O3-FeO-MnO-MgO based to simulate ULC steel grades. It has been observed that the reoxidation rate shows a good relationship with (T. Fe) content in slag. In case of (T. Fe) content higher than 1.5 weight per cent, the reoxidation rate increases linearly with increasing (T. Fe) content. For a given (T. Fe) content, it decreases with the increasing (CaO)/(Al2O3) ratio of the slag. However, in the case of (T. Fe) content lower than 1.5 weight percent, no particular relationships are observed between the reoxidation rate and (T. Fe) content or the (CaO)/(Al2O3) ratio of the slag. These results were used to propose for an aim a slag composition for the ULC steel grades in a steelmaking plant. Keywords: slag deoxidation, slag killing, slag composition control, IF steel, ULC steel grade

Jan 1, 2004

By P. van der Heever

The genesis of Simrac?s technology transfer practices and future initiatives are discussed in this report. Simrac produces a relatively large volume of research-based health and safety outputs that must be communicated to its tripartite stakeholders and to other interested and affected parties. The wide spectrum and complexity of the transferables, together with the diversity of end-user needs and skills of the recipient population, necessitate customizing of technology transfer practices. In an attempt to optimize this process, a variety of practices are employed. Information is transferred by means of publication and dissemination of a variety of reports (paper, website and CD).Knowledge transfer is directed to health and safety practitioners by means of workshops, seminars, best practice booklets, handbooks and textbooks. Promotion of recently completed projects is directed at targeted recipients by means of project launches. Only isolated cases of piloting and implementation of technologies have been undertaken due to lack of resources and past organizational focus. It is anticipated that Simrac?s new organizational structure and management system, together with end-user involvement by industry champions, from project inception to implementation, will enhance the effectiveness of the technology transfer process.

Jan 1, 2002

By M. W. Hildyard

A blast was engineered close to a tunnel in a deep-level mine with the purpose of studying the wave interaction with the tunnel. Numerical modelling of seismic wave propagation was used in both the forward planning and the back-analysis of this experiment. This paper presents the forward analysis. A likely model for a propagating blast was investigated and developed. This model predicts the influence of the velocity of detonation of the blast and the rise-time of the blast on the radiation pattern, and hence on the expected positions of maximum velocity at the tunnel surface. An attempt was made to quantify the parameters of the blast model, using waveform data from two other blast experiments. The blast model caused particle velocities which were an order of magnitude lower than these measured velocities. Large values for blast pressure were required to match the amplitudes of the recorded velocities. An alternative ?effective? source with a similar mechanism but increased diameter was proposed to account for the higher velocities. It was established that distant velocities scale with the square of the borehole diameter. A calibration blast at the experimental site was also modelled. Agreement in the waveforms was not sufficient for conclusive statements to be made about the validity of the source model. However, the modelled waveforms show an encouraging correspondence with some measured waveforms. This gave confidence that the model could be used to examine wave propagation around the tunnel, and allowed a scaled source to be developed for forward analysis of the main experiment.

Jan 1, 2001

By A. C. Legg, M. T. Malema

Keywords: Pyrometallurgy, flash, smelting, furnace, nickel, copper, Botswana BCL Limited operates the only Flash Smelting Furnace on the African continent, at Selebi-Phikwe, situated in north-eastern Botswana. The furnace was commissioned in 1973 and produces a high-grade sulphide matte containing nickel, copper and cobalt, which is shipped to refineries in Zimbabwe and Norway for further processing. This paper outlines the recent process improvements and plant expansions that have resulted in a capacity increase from 40 000 to 60 000 tons per annum of metal production.

Jan 1, 2006

By S. Kitamura

In recent years, the amount of ferritic stainless steel production has increased. However, the rust formation by the salt spray test was pointed out in the past. At the centre of the circular rust zone, pitting corrosion where water-soluble nonmetallic inclusions were embedded was observed. These inclusions originated from the suspended refining slag and consisted of multi-phase oxides and sulphides. By the experiments and thermodynamic consideration of the water-solubility, not only CaO or CaS, but also lime rich calcium-aluminates or calcium-silicates have shown large water-solubility. The composition of oxide phase in the inclusions was almost the same among the samples from molten steel, slab, or cold rolled sheet. On the contrary, CaS was clearly observed around the oxide in the sample of cold rolled sheet, although it was not found in the molten steel or slab samples. The enrichment of sulphur occurred from the desulphurization reaction of the suspended slag particles in the molten steel and also occurred from the diffusion of sulphur to the oxide inclusions during the heating of the slab. The optimization of refining slag composition has lead to produce the ferritic stainless steel without rust formation. Keywords: stainless steel, rust, calcium aluminates, calcium sulphides, water-solubility, refining slag, composition control of inclusions.

It is estimated that the tailings dam of the Mouteh Gold Mine, in Iran, contains more than 770 kg of gold. Microscopic analysis reveals that sulphide minerals and active carbon are the main sources of the gold in the tailings residue. Flotation and cyanidation tests on the samples of tailings were conducted. Flotation concentrates, containing around 87.79% of the gold, which were associated with sulphide minerals, were recovered. By regrinding, roasting, and cyanidation of the flotation concentrate, the gold dissolution recovery was in the range of 87.8 to 98.4%. The carbon-in-column method was used to recover 98% of the gold from the solution. Keywords: gold ore, pyrite, flotation, roasting, cyanidation

Jan 1, 2009

By M. Kawakami, K. Suzuki, T. Takenaka, S. Yokoyama

Molten NaNO3-NaNO2-KNO3mixture is used as a heat transfer medium at high temperature. One of the most important properties of this mixture is the heat capacity. In the present work, the enthalpy change with temperature was measured by the drop calorimetric method to evaluate the heat capacity. The results are summarized as follows: The enthalpy of the mixture increased linearly with the temperature. From the slope of the line, the heat capacity was evaluated. The heat capacity of pure NaNO3, NaNO2and KNO3was 0.129,0.110 and 0.142 kJ/mol/K, respectively. These values are in fairly good agreement with the published data. In the binary and ternary systems, the molar additivity of heat capacity, which is well known as Neumann-Kopp’s law, was obtained. The heat capacity of HTS1and HTS2, which are well known ternary mixtures of practical use, were in the range of published data.

Jan 1, 2004

By N. Demirel, O. Gölbasi

Draglines are massive machines extensively utilized in opencast mines for overburden stripping. The demanding working environment induces fractures, wear and tear, and fatigue failures in dragline components and eventuates in extended maintenance, lengthy downtimes, and loss of production. The bucket is the main source of external loads on the machinery, since interactions with ground materials take place in this region. This study aims to develop a generic finite element model of the stress on an operating bucket. This entails (i) three-dimensional modelling of a dragline bucket, (ii) analytical estimation of resistive forces in the bucket movement, (iii) three-dimensional simulation of the moving bucket using finite element analysis (FEA), and (iv) sensitivity analysis to examine the effect of formation characteristics on stress variation. Simulation results imply that the drag hitch and digging teeth are the elements of the bucket that are most prone to failure. In addition, sensitivity analysis indicates that internal friction angle of the formation is the dominant parameter leading fluctuations in stress values. Changes in stress level are least influenced by formation density.

Jan 1, 2015