Search Documents

By Michael L. Clar

This volume is an annotated bibliography of published literature pertaining to the occurrence and control of surface and groundwater in underground coal mines. This literature was used to develop Volume 1 of this report, which assesses the feasibility of water diversion and overburden dewatering for underground coal mines in the Appalachian Region. Each abstract is followed by subject descriptors. the abstracts are listed alphabetically by title and are numbered consecutively. These numbers are used in the subject index to help the reader locate the appropriate articles.

Jan 1, 1981

Although the mining industry has achieved record-low fatalities and injuries for each of the last three years, there are still too many miners injured or killed in this nation ís mining operations. Many mining injuries or deaths might have been prevented by using risk assessment to identify and control or eliminate the hazards associated with a task. To focus attention on the importance of conducting risk assessments in keeping mining workplaces safe and healthful, MSHA introduced this initiative on October 12, 2004. This initiative is called SLAM. SLAM is an acronym for Stop, Look, Analyze, and Manage. The steps involved in SLAM are: Stop ñ stop and consider the work involved Look ñ look for and identify the hazards Analyze ñ analyze what needs to be done Manage ñ manage safety by developing and implementing controls Everyone should be aware of the risks of an accident before beginning a task. It may not always be obvious that performing a seemingly routine task could result in an accident. That is why conducting a risk assessment is so important. Itís important to remember that over time a mining workplace seldom remains unchanged. Risks must be assessed whenever procedures or processes change, whenever new tasks are started, or non-routine tasks are performed.

Jan 1, 2005

By Peter Swanson, John Rettkowski

As part of a research program to reduce injuries and fatalities in the U.S. mining workforce, NIOSH is investigating the potential use of noncontact vibration measurements to identify hazardous ground fall conditions. In the present study, the effectiveness of remote vibration sources in exciting resonant responses in damaged structures is examined. Initial experiments were performed on a damaged concrete slab in a controlled environment. Vibration response was measured with a laser Doppler vibrometer using both single-point and two-dimensional array recordings. Excitation sources included direct mechanical impacts to remote portions of the slab and a remotely located industrial demolition hammer. Surficial damage was effectively delineated with both sources through visualization of vibration response in spectral bands selected to discriminate wave propagation from large-scale slab resonance effects.

By G. L. Mowrey, S. D. Maksimovic

An important element of the U.S. Bureau of Mines (USBM) mining research program is the development and evaluation of reliable coal interface detection (CID) systems. Commercially available CID sensors based on natural gamma radiation (NGR) are only applicable if the immediate roof is composed of shaley material. The USBM has made numerous underground and laboratory measurements using several NGR systems approved for installation on mining machines by the Mine Safety and Health Administration. In addition, two small handheld NGR instruments were used to make comparative measurements. Underground NGR measurements in 10 different coal seams, potassium-uranium-thorium radiometric analyses on samples from 16 seams, and chemical analyses of coal and rock for correlation with NGR counts were made. Laboratory test results on the effect of air gap and sample thickness, size, and weight on the NGR measurements, as well as general results of the various NGR systems, are discussed.

Jan 1, 1995

By F. H. Willcox

This publication is the third of a series of reports on hazards and the prevention of accidents at blast-furnace plants that is being published by the Bureau of Mines, Technical Paper 106a being the first and Technical Paper 136b the second of the series. This bulletin, which is arranged in three parts, treats of the causes and prevention of blast-furnace breakouts, explosions, and slips. The first part discusses blast-furnace breakouts, the hazards therefrom, causes, and features of furnace design and methods of operation that tend to prevent breakouts or lessen their number, and points out safety measures to be adopted. The second part takes up the theory and causes of gas explosions at blast-furnace plants and reviews the better methods in use for handling gas. The third part analyzes the causes of hanging and scaffolding in blast furnaces, with the resulting slips that frequently cause injury to the plant and danger to the workmen, describes features of construction and furnace design and methods of operation employed to prevent hanging and slipping, and suggests precautions and safeguards.

Jan 1, 1917

By James M. Baugher, Donald W. Conrad, William J. Wiehagen

This report describes a process for quickly developing information that is useful for skills training. The process is called job training analysis (JTA). Its main use is to structure skills training at the jobsite. JTA supports structured skills training by identifying the job duties, tasks, and steps and the reasons why those job components are important. The outcome of the JTA process is a worksheet—a training outline based on the knowledge and expertise of experienced workers. Time invested in developing a JTA will result in significantly more time saved when it is used appropriately by skilled trainers. Like a roadmap, JTA saves time and energy. Experimental work at several mine sites helped document, refine, and validate the JTA process. JTAs for two mining jobs—roof bolting and lift truck operation—at two different mine sites are used to illustrate some of the concepts and the specific JTA process described in this report. The work at these two sites was influenced by cooperative work between the Mine Safety and Health Administration (MSHA) and the National Institute for Occupational Safety and Health (NIOSH) at several other mine sites and prior collaborative work with the U.S. Navy. The mining JTA process is grounded within the military research on the design of instructional systems. MSHA and NIOSH worked to simplify and apply the military training development model for mining industry use through collaborative work at several mine sites. The JTA process involves three activities: (1) planning, (2) a 1- to 3-day workshop where the JTA is developed using facilitated work with subject-matter experts, and (3) followup. Guidelines and considerations for each of these activities are included. Results indicate that the JTA process has been well received and valued by mining industry participants. It blends aspects of health and safety, production, maintenance, and crew coordination.

Jan 8, 2006

By William J. Campbell

Three types of X-ray analytical instrumentation were compared for applications in the secondary brass and bronze industry. The instruments were a conventional X-ray spectrograph, a portable X-ray spectrograph, and a radioiso-topic X-ray analyzer using balanced filters. The following two general applications were considered: Rapid identification for sorting scrap metals and quantitative analyses to provide guidance in the melting and casting of alloys. Twenty-three analyzed copper-base alloys were used as standards. Although the alloys varied widely in composition, matrix correction procedures were not necessary except for copper. The conventional X-ray spectrograph provides positive identification of the alloys and quantitative values for the six elements investigated--aluminum, copper, iron, lead, tin, and zinc. Equivalent results were obtained with the portable X-ray spectrograph for those elements whose characteristic X-rays are in the wavelength range of the instrument. The radioisotopic X-ray analyzer distinguishes certain groups of alloys and provides quantitative determinations for copper, lead, tin, and zinc. The sensitivity of the analyzer was marginal for the determination of small concentrations of elements of atomic number 26 or lower.

Jan 1, 1972

By Keith A. Heasley, John L. Ellenberger, Paul W. Jeran

In this paper, a state-of-the-art, three-dimensional, full waveform, microseismic system was used to analyze the rock failure around a deep (> 750 m (2500 ft) of cover) bump-prone longwall panel. The microseismic system consisted of both underground and surface geophones coupled through radio telemetry and a fiber-optic network to produce pseudo real-time detection and location of seismic events surrounding the coal seam. This was the first microseismic installation of this scope at a U.S. coal mine, and the system was intended to help determine the exact strata mechanics associated with the redistribution of stress and the associated gob formation at one of the U.S.’s deepest longwall mines. Overall, 5,000 calibrated seismic events were recorded during the mining of one panel, including a Richter magnitude 4.2 event which occurred inside of the array. Analysis of these events provides a number of notable insights into the rock mass behavior. For instance, the longwall panel was widened during the retreat process, and the mining-induced seismicity shows a distinctly different behavior between the start of the panel, the mining of the narrow part of the panel and the mining of the wider part of the panel. Also, in itself, the acquisition of the ML 4.2 event was a major milestone in geomechanical and bump research. This is the first time that such an event has been recorded with this detail and accuracy at a bump-prone coal mine in the U.S. The analysis of this single event has set distinct new limits on the relationship between mining seismicity and coal bumps.

By Walter E. Lewis

The Fort Randall Reservoir project, on the Missouri River at Pickstown, S. Dak., was designed by the Corps of Engineers and is part of the Missouri River Basin Development Program. The location of the project with respect to adjacent features is shown' in figure 1. When the project is finished, it will include a large earthwork dam and 12 circular tunnels, 8 of which will be equipped for power and 4 for flood control. Various phases of the construction have been contracted to independent companies, and at present four companies are working on different phases of the project under a rigid time schedule. Western Contracting Corp. is the contractor on stage II, earthwork; Johnson-Winston Construction Co. is the contractor for construction of the intake towers at the upstream side of the dam; McCarthy Improvement Co. has the contract for the power house and the outlet works on the downstream side; and Silas Mason Co. has the contract for driving the power and flood-control tunnels. The latter two companies use the same roads for ingress and egress to their respective work areas and the same general waste dump area. Under such circumstances, it is necessary that each company stay on a time schedule in regular sequence to avoid interference with the other.

Jan 1, 1951

By V. T. Dow

This report describes construction details and methods used in driving the 5490 tunnel at the Kennecott Copper Corp, property, Bingham, Utah. The tunnel will provide railroad access to the world-famous open-pit copper mine at the projected 5490 level. This publication is one of a series prepared by the Bureau of Mines to depict mining operations and techniques in various mining districts in the United States. Utah Construction and Mining Go. (formerly Utah Construction Co.), contractor on the tunnel project, began work during September 1956 and completed the project in February 1959. The tunnel is 18 feet wide, 24 feet high, and about 18,000 feet long, It will accommodate a railroad locomotive on standard- gage track. With the exception of the last 1,700 feet, the tunnel is supported by steel sets embedded in concrete lining. The 1,700-fact segment of the tunnel is supported by timber sets that will eventually be removed as the pit is deepened.

Jan 1, 1962

By Gustav Wirth

"ABSTRACTIn exothermic and endothermic catalytic reactions, control of the temperature is of utmost importance. Basic calculations are developed for determining catalyst volumes of various types of reactors that give particular temperature distributions, and the individual designs are compared.INTRODUCTIONA narrow range of permissible operating temperatures characterizes many, catalytic reactions, and yields of the desired product are reduced sharply if operating temperatures fall outside of this optimum range. In order to achieve close temperature control, reactors with internal heat exchange have been developed in which thin layers of catalyst are located between cooling surfaces.The temperature distribution for an exothermic reaction in such a thin catalyst layer is shown in figure 1. Reactive gases flow downward through the catalyst section, which is 2so wide. It is assumed that a constant amount of heat is generated per unit of bulk catalyst volume, and that this heat is entirely removed through the walls. Consequently, except for a short section at the entrance of the reactor, the heat of reaction is not available for raising the temperature of the gases. Thus, at all points equidistant from the axis, the temperature is the same throughout the entire reactor. At the middle of the gas stream, the temperature is designated as uo. Traveling radially from this point, the temperature decreases because of the removal of heat through the walls and reaches, in the vicinity of the cooling surface, the value u1. Over a relatively narrow zone of width, b, the temperature falls to the value u2 at the cooling surface. Because inadequate data are available on heat-transfer coefficients for a gas flowing through a porous bed, and also because the narrow zone, b, is probably without effect on the reaction by virtue of its low temperature, the temperature drop in this zone at the cooling wall was disregarded. The following calculations were made on the basis of the temperature drop (u0 - u1) resulting from heat conduction within the main body of the catalyst bed only."

Nov 1, 1950

By John J. Sammarco

Miners depend most heavily on visual cues to recognize underground mining hazards; consequently, illumination plays a critical role in miners? safety. Some hazards are located in the miners? peripheral field-of-view (10 degrees to about 60 degrees off-axis) or on-axis (0 degrees). The objective of this research was to determine if there were visual performance improvements when using solid-state cap lamps with light-emitting diodes (LEDs) as compared to incandescent light bulbs commonly used in miner cap lamps. Recent research has indicated that an increased short-wavelength content of the spectral power distribution of LEDs relative to incandescent lamps improves peripheral visual performance for low-light (mesopic) conditions. The visual performances of nine subjects were quantified by measuring the subjects? speed and accuracy in detecting floor objects located on axis and at ±20 degrees off axis. The objects were located near field (1.83 meters) and far field (3.66 meters). Upon presentation of the objects, subjects would count and point to each object using a red-laser pointer. The object detection response time and number of missed objects were recorded. The results of the visual performance comparison for an LED, a prototype LED, and an incandescent cap lamp are presented. There we no missed objects when subjects used the LED-based cap lamps but, there were three missed object occurrences when subjects used the incandescent cap lamp. The mean detection time when using the incandescent cap lamp was 55.3% greater than the prototype LED cap lamp and 43.5% greater than the LED cap lamp. It can be inferred from this data that the spectral distribution of LED-based cap lamps could enable significant visual performance improvements as compared to incandescent cap lamps1.

Jan 1, 2007

The 1969 Lignite Symposium was held at Grand Forks, N. Dak., on May 1-2, 1969. Cosponsored by the University of North Dakota and the Department of the Interior, Bureau of Mines, the meeting was the fifth in this series. Registrants from many States and Canadian Provinces attended the meeting representing many segments of energy-oriented companies, State and Federal Government, and universities. At 2-year intervals, these symposia provide a common meeting place where recent research and developments in technology and utilization of energy resources with emphasis on solid fuels (lignite) are presented. Proceedings3 of the previous symposia including a Forum held in 1958 have been published.4

Jan 1, 1970

By A. B. Hooker, L. C. IlsLey

Explosives have been fired electrically for several decades. Mountains have been tunneled, deep shafts sunk, extensive coal and metal mine workings excavated and, in times of war, railroads, buildings, bridges, and fortifications have been destroyed by means of electrically fired explosives. Modern engineering depends so much on explosives that their safe and efficient handling and especially their detonation are of prime importance to all those connected with the use of explosive agents. Electric shot-firing is only one method of igniting explosives, but it is rapidly spreading and because of certain inherent safety features should be encouraged. Data collected by the Bureau of Mines indicate that in the United States a large percentage of the blasting in quarries, shafts,· and tunnels, and from 15 to 25 per cent of the blasts in mining operations, are set off electrically. The Bureau of Mines is interested in electric shot-firing because of its use in mining, and especially because electric methods, when properly applied, are undoubtedly safer than other methods commonly used. Electrical problems of many kinds must be solved in dealing with the various phases of electric shot-firing. Success in using an electric detonator is closely linked with the resistance of its bridge, the resistance of its leg wires, and the insulation of its current-carrying parts. The proper layout of a circuit where a number of shots are to be fired simultaneously depends not only on the types of detonators that are used and their arrangement and interconnections, but also on the size and insulation of the wire leading back to the source of power, and even on the source of power itself. Various types of electric shot-firing machines have been developed, and these offer still another field for study. In investigations of electric detonators and electric blasting equipment, the oscillograph is valuable because it can record electrical activity over very short intervals of time. By its use more complete information about electrical performance can be obtained than by any other means.

Jan 1, 1926

By John P. Shubilla1, Nicholas Kyriazi

A joint effort by the Pittsburgh Research Center (PRC) and the Mine Safety and Health Administration (MSHA)3was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), held up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSR's in the fifth phase of testing from mid-1993to early 1996. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS) at PRC. These results indicate that most of the apparatus, if they pass their inspection criteria, perform satisfactorily.

Jan 4, 1996

By L. D. Patts, G. H. Schnakenberg

Achieving substantial reductions in the exposure of underground miners to diesel particulate matter in a number of metal and nonmetal mines in the U.S. depends on the ability of the industry to widely implement advanced diesel emissions control technologies, primarily diesel particulate filter (DPF) systems. Recent field studies showed that diesel particulate filter systems with Cordierite and silicon carbide ceramic filter elements are capable of reducing concentrations of diesel particulate matter and elemental carbon by more than 70 and 90 percent, respectively. But those studies and several other attempts to implement DPF systems in underground mines revealed a number of relatively unique technical and operational challenges that are limiting industry-wide implementation of this technology. This paper provides detailed analysis of some of those challenges and short overviews of several projects launched by NIOSH Pittsburgh Research Laboratory in an attempt to provide the underground mining industry with more adequate DPF systems. These systems employ advanced technologies to overcome the most pronounced challenge, the regeneration of DPF elements installed on mining engines that generate relatively low exhaust temperature. This paper presents essential findings obtained through a long-term evaluation of DPF system with diesel fuel burner technology installed on a heavy-duty load-haul dump vehicle in an underground metal mine. In addition, the essential results of the laboratory evaluation of a popular on-highway DPF system which was adapted and optimized for underground mining applications will be summarized in this paper.

By Todd M. Ruff

Blind areas around construction equipment are a major contributing factor in incidents involving a piece of equipment striking a worker. In highway construction, these types of incidents result in an average of 22 deaths a year in the United States. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these incidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers or other objects. Several camera and sensor systems are available for this application. These systems were evaluated on various trucks used in road construction and maintenance. Tests were conducted on sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted on dump trucks and utility vehicles during the warmer months to study the effectiveness of the systems in highway work zones. Results showed that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in congested work areas.

By H. L. Anthony, A. C. Richardson, G. D. Coe

"INTRODUCTION The Warrior View mine of the Seaboard Coal Corporation is located in Tuscaloosa County on the Warrior River about 14 miles northeast of Tuscaloosa, Ala. The Brookwood bed at this point yields a coal with fair coking qualities, and the product from neighboring mines on this bed has been used for the manufacture of blast furnace coke. The output of the Warrior View mine, however, is used exclusively for domestic and steam-raising purposes.This paper continues the series° of reports on the washability of Alabama coals which are based upon the study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal mining companies. This paper contains screen-sizing and float-and-sink tests of a representative sample of run-of-mine coal, and flakiness and crushing tests on certain sizes.Published information on the Brookwood bed is very meager. Fieldner6 gives the proximate and ultimate analyses for a number of seam samples taken from representative mines working this bed. Gandrud and Britton7 show sections of this bed taken at Searles, Ala. They also give the specific gravities of the coal, the bone, and the shale partings.Table 1 give the proximate and ultimate analyses for the 3/4 to 3/16 inch size of raw coal. Table 2 gives the sulphur content and the ash fusibility temperatures of the float-and-sink fractions for this same size. The character of the coal is very uniform throughout the range of sizes produced and, as it was not convenient to have these analyses on all sizes, this size was chosen as being representative of the coal. From the information available it is evident that the coal preparation problem is restricted to one of ash reduction.SAMPLING AT THE MINEAt the Warrior View mine the run-of-mine coal is dumped from the mine cars upon a 3-inch grizzly. The oversize is crushed in rolls set at 24 inches and joins the undersize before being elevated to the raw-coal bin ahead of the jig. The sample was caught at the point where elevates discharges into the raw-coal bin, by taking a proportional amount of the coal at 10-minute intervals over the period of a day's run, The total sample amounting to 2.7 tons was shipped to the laboratory at Tuscaloosa for the washability studies."

May 1, 1932

By L. A. Stewart

This paper describes all occurrences of barite in Arizona that were known or reported to the authors. The history, ownership, production, and geologic setting are discussed for most of the deposits. The uses and specifications of product grades are briefly discussed. Seventy-five deposits were examined in 9 of the 14 counties of the State. The descriptions are given under county headings. No occurrences were reported in the four northeastern counties of Coconino, Navajo, Apache, and Greenlee, nor in Santa Cruz in the southern part of the State. From about half of the deposits examined, 55 samples were taken; of these, 45 were for chemical analysis, and 8 larger samples, ranging from 100 to 350 pounds, for beneficiation tests. A 30-ton bulk sample was taken for pilot-plant tests. Bench-scale flotation tests of the eight samples employing several different procedures and reagent combinations yielded marketable-grade barite products with barite recoveries ranging from 60 to 97 percent. Five of the samples contained enough fluorspar to warrant its recovery. Acid-grade concentrates, which accounted for fluorspar recoveries of 45 to 70 percent, were obtained from three of these ores. Batch laboratory tests of a representative portion of the 30-ton bulk sample revealed that acid-grade fluorspar and high-grade barite concentrates could be recovered. Results of the laboratory and continuous pilot-plant tests of this ore will be presented in a separate report.

Jan 1, 1960

By E. Chilton

The National Institute for Occupational Safety and Health (NIOSH) has been conducting re-search to determine the influence of mining machine mounted water sprays on airflows and methane concentrations at the face when blowing ventilation systems are used. Tests were conducted in a full-scale ventilation gallery. Airflow speeds and directions were measured at several locations near the face with ultrasonic anemometers. Methane was released from the face and concentrations were measured in the entry at locations above the mining machine using fixed point methanometers. Changes in airflow speed, direction, and methane concentrations were correlated with water spray operations. The test results using different spray arrangements and water pressures showed that operation of the machine-mounted sprayers can improve face ventilation effectiveness by increasing the velocity of airflow moving toward and away from the face. The improved ventilation resulted in reduced methane levels near the face.