Search Documents

By L C. Taylor

Very small scale testing has been shown to be able to predict quite accurately, in many situations, the results of full scale testing. Small scale tests are more cost efficient, easily observed, and easily instrumented than full scale tests. Over the past 10 years small scale testing in the Dynamic Effects Laboratory at the University of Maryland has been used to successfully study the response of structures and soils to explosive detonation. Small scale testing has been successfully used to predict full scale results in underwater cratering and channeling, the loading (both pressures and impulse) on vehicles due to the detonation of buried charges, the positive effects of bottom shaping for military vehicles to reduce this loading, and the movement of obstacles underwater by explosive charges.

Jan 1, 2012

By Deane Boddorff

A 440 Volt AC power line is a typical power source for energizing electric blasting cap circuits in driving hard rock tunnels. A common misconception exists that the caps actually see 440 Volts. This paper describes an analysis of the entire blasting circuit determining the current flowing and the voltage drops through each component. If, from such an analysis, one determines that the current to the caps is too low or too high, the components that require changing are easily recognized.

Jan 1, 1975

By S B. Richardson, R E. Danell, D Mead, N T. Moxon

Explosives provide a very concentrated source of energy which is often well in excess of that required to adequately fragment the surrounding material. Blast design, environmental requirements, production requirements and the lack of detailed insitu geological data generally limits the degree to which the explosive energy distribution within the blasthole can be significantly altered using, for example, different explosive formulations or variable loading techniques. However, increased flexibility can often be exercised over a blast through the use of air-decks.

Jan 1, 1993

By Janos Foldesi, Calvin J. Konya

The determination of the number of primers necessary to efficiently initiate an explosive column charge is essential to good blasting. If the number of primer is insufficient, the total energy stored in the main charge will not be released. On the other hand, the use of too many primers will be counterproductive and raise the blasting cost. Tests were conducted by the authors to determine the correct priming procedure for a basalt quarry. This paper describes the results of those tests.

Jan 1, 1976

By Q Liu, P D. Katsabanis

Dust explosions in underground sulphide and oil shale mines result from the detonation of explosives in the blasting operations. Explosive composition, oxygen balance, priming and ideality of detonation were examined theoretically and experimentally in the presence of reactive sulphide dust. It was found that the temperature as well as the chemical composition of the gaseous products of detonation are the controlling parameters related to the explosive. Non aluminized, oxygen balanced emulsion explosives were proven to be relatively safe, while explosives creating combustible products were proven to be extremely dangerous due to the secondary flame they generate. Since a large number of dusty orebodies are often very friable, low density emulsion explosives are also examined for application in production blasting.

Jan 1, 1991

By Winston Wilches B., Scott Scovira

This paper discusses recent changes to the emulsion blend blasting agent used at the Drummond Pribbenow Mine in Colombia, one of the world’s largest open pit coal mines, and the resulting improvements in rock breakage and excavator productivity. Based on field evaluations, the use of High Density Ammonium Nitrate (HDAN) can be effectively implemented in an emulsion blend blasting agent, yielding excellent results in terms of energy release, shelf life and velocity of detonation (VOD). Field evaluations showed that formulations using HDAN exceed the performance of the actual 50%/50% emulsion/ANFO blend using Porous Prill Ammonium Nitrate (PPAN). PPAN is conventionally used for emulsion blend manufacturing, with physical characteristics to facilitate sensitivity during the detonation process.

Jan 1, 2014

By Jared Redyke

Thursday, October 14, 1999 marked another important milestone for America’s space program. At exactly 10:05 AM EST on a beautiful, sunny Florida morning, Dykon, Inc. of Tulsa, Oklahoma detonated approximately 300 pounds of explosives to fell the seven million pound Umbilical and Mobile Service Towers at Space Launch Complex 41 (SLC-41) at NASA’s Cape Canaveral Space Station. Completed in 1965 at the height of the Space Race to the moon, the Mobile Service Tower/Umbilical Towers (MST/UT) were part of the Titan rocket launch facilities. The MST was 265 feet high and weighed over five million pounds. The UT was 175 feet high and weighed over 2 million pounds.

Jan 1, 2001

By Mo Jadbabaei, Scott Harrison

There is very limited information available regarding the air pressures, flow rate, and velocity profiles in blast hole air drilling applications. Currently, many people are using incompressible flow correlation to calculate the bailing velocity. In this article, air pressure, flow rate, and velocity profiles are calculated using compressible flow theory. The airflow at the bottom of the hole is simulated using the jet flow theory. The concept of choking condition is introduced, and it is concluded that the velocity at the nozzle exit cross section cannot exceed sonic velocity. The minimum pressure required for achieving choked condition at the nozzle cross section is calculated. Choked and overchoked flow conditions at the nozzles are examined, and the maximum achievable cleaning power is correlated to the nozzle size and pressure.

Jan 1, 1999

By Justus Deen, Paul Sterk

Overbreak into the wall rock of a development drift leads to the inevitable need to rehabilitate a drift. Moreover, overbreak in a production heading can lead to external dilution and lower ore grades. Both of these factors are critical to bottom line costs of underground operations today. The geology of the Homestake orebody makes this an even more complex problem. For over fifteen years the Homestake Mine has attempted to implement perimeter blasting techniques that are both safe and cost effective. Many practical perimeter methods and products have been tested including air decking; low density emulsions; various types of stick powder; various decoupling media including rope, low density ANFO, polystyrene ANFO, salt based ANFO, and various grain detonating cords up to 200 grain.

Jan 1, 1997

By Bin Feng, Xiang Fang, Tao Guo, Fandong Lu

Abstract: Rough set theory (RS) can find useful information from a large number of data and generate decision rules without prior knowledge. Support vector machines (SVM) have good classification performances and good capabilities of fault-tolerance and generalization. To effectively control blasting vibration effect, prediction model of blasting vibration parameters based on rough sets and support vector machines are established. Particle swarm algorithm (PS) is used to dynamically discretize attributes. Then, according to the optimal particle calculated by the PS algorithm, the decision table is established. After eliminating less importance attributes and data, then SVM is trained and established for prediction. The model can deal with both quantitative and qualitative factors such as aperture and cast direction, and analyze their importance to peak vibration acceleration value. The improvement of prediction accuracy is verified by testing data.

Jan 1, 2014

By E. Contestabile, B. von Rosen

On August 5th, 1998, a tractor-trailer carrying approximately 18,000 kg of blasting explosives, struck a rock face on the side of the road near the town of Walden, Ontario. Eye-witness accounts of the incident state that there was an intense fire for approximately 30 minutes before the detonation. The detonation caused severe damage to the tractor-trailer, shifted the pavement and caused blast damage to the rock face. A rock fragment was recovered almost 2.5 km from ground zero and a 70 kg piece of an axle assembly was recovered over 1 km from the site. Windows were cracked at distances of almost 3 km.

Jan 1, 2001

By Abdulkadir Karadogan, Zikri Keti, Umit Ozer, Mehmet Aksoy, Ulku Kalayci

This paper presents an investigation about how the motions of blast induced vibration waves were affected by the presence of the fault planes. This study was carried out at Espey Open- Pit Boron (Colemanite) Mine in Turkey. Within the scope of the study, ground vibration components were measured for 8 shots using 9 vibration monitors, considering the direction of the fault. Measurement stations were located around the fault line that intersects the open-pit mine in the north-south direction and on different benches along the fault plane. Then, the data of the vibration components obtained from the 77 recorded events were analyzed and the results were presented.

Jan 1, 2012

By David Kennedy, Noel Hsu, Miguel Araos

The use of bulk explosive for mining applications started in the 50’s. Since then millions of tons of that material have been transported by road. However during that time, there have been several road incidents involving them. This type of incident has forced the explosives manufacturers as well as regulatory organizations to look for a better classification of explosives in order to regulate the industry as well as to mitigate community concerns over the classification of mixtures of substances that are regarded as precursors to explosives.

Jan 1, 2006

By P D. Kasbanis, Lyall Workman

The energy output of an explosive is typically calculated using an equation of state and computer applications. Results are reported as weight and bulk strength, either in absolute terms or relative to ANFO. The effect of the equation of state selected and the assumptions regarding the energy calculation are considered and interpreted for the purpose of blast design. It appears that variations in the heat of detonation which result from the selection of the equation of state and parameters associated with it are not sufficient to significantly affect blast patterns, explosive consumption and costs. However variations stemming from the use of "available energy" associated with a cut-off pressure are significant, suggesting in many cases large pattern expansions. The validity of the various approaches is discussed and blast design results based on the energy calculated by the different approaches are presented and evaluated.

Jan 1, 1996

By Justus Deen, Paul V. Sterk

Through the 119 year history of the Homestake Mine various methods of raise mining have been used, these include conventional, bored, and drop raises. These raises provide passage for men and supplies, provide ventilation, transfer broken rock from level to level, and serve as emergency escapeways. As the 1980s came to a close, many of the larger ore bodies in the mine had been mined out. This has resulted in many crown pillar situations that required a method to mine them. In addition, the Homestake ore body also contains numerous ore reserves that have short vertical height. The ore itself can be from vertical to 50 degrees in dip. Due to the high cost of drift and ramp development many of these ore bodies are sub-economic using conventional mechanized cut and fill mining.

Jan 1, 1996

By Justus Deen, Paul V. Sterk

Through the 119 year history of the Homestake Mine various methods of raise mining have been used, these include conventional, bored, and drop raises. These raises provide passage for men and supplies, provide ventilation, transfer broken rock from level to level, and serve as emergency escapeways. As the 1980’s came to a close, many of the larger ore bodies in the mine had been mined out. This has resulted in many crown pillar situations that required a method to mine them. In addition, the Homestake ore body also contains numerous ore reserves that have short vertical height. The ore itself can be from vertical to 50 degrees in dip. Due to the high cost of drift and ramp development many of these ore bodies are subeconomic using conventional mechanized cut and fill mining.

Jan 1, 1996

By P Wapner, C Lo Edwards, S CO Schmidt, J N. Johnson, R Oliver

Shale oil recovery rates that can be achieved in underground in situ retorts can be strongly influenced by the shale breakage and fragment-size distribution achieved during rubblization. Since the fragmentation pattern in the retort is a direct result of the blast design used for rubblization, the characterizing blast parameters should be carefully selected. Explosives should be matched to the host material and blast geometries properly chosen so that the required fragmentation results are achieved at optimum costs. Special attention must be directed to selecting blast parameters that produce uniform bed permeability, suppression of fines, proper fragment size distribution, and minimal damage to the retort walls and ceiling. The influence of joints and natural fractures should also be known. In instances where the requisite blasting parameters are unknown, they should be determined from test blasts.

Jan 1, 1979

By Robert Hopler

INTRODUCTION NOT so very many years ago the farm was about the last place where one would expect to find up-to-date mechanical appliances. Steam, explosives, electricity—the factors which have made the world in general, and America in particular, what it is today— were indispensable for the railroad and the steamboat, the factory and the mine, but the farmer’s work was generally run on a comparatively small scale, and was mostly done by the muscles of men or draft animals. Today, however, the farmer as well as the manufacturer, the contractor and the miner, fully appreciate the value of labor-saving devices. Every up-to date farm, large or small, has modem machinery that tends to reduce the cost of production or to improve farm products.

Jan 1, 2011

By Bob de Raadt

For a long time industrial underwater blasting has stood in need of a calculation method, for the determination of shockwave-proof as well as shockwave-effective charge distances to objects in water. After a brief discussion of the physical background of the shockwave mechanism in water, the author discusses an empirical theoretical computing method based on the "Bubble boundary" concept. The practical application of this model is finally shown in an account of a few underwater blasting operations in which charge weights of c.1-1000 kg were involved.

Jan 1, 1980

By Travis Davidsavor, Stanley: Dong Vitton

Concrete is a common construction material used throughout the world, and with increasing demand of fast-track construction, blasting and concrete casting are occurring simultaneously at many sites where rock is being excavated for concrete placement. However, there has been significant disagreement in the construction industry as to what intensity of shock vibrations green, or fresh concrete can tolerate. Peak particle velocities are often arbitrarily chosen, or are simply based on materials such as plaster and drywall that have been more thoroughly studied in relation to damage. Previous research on green concrete has used the concrete’s static strength subjected to shockwaves at different ages as the primary damage criteria. In addition, the static strength tests have been based on curing time. However, changes in temperature or humidity can dramatically alter the hydration rate, which affects strength development of different cements. To account for temperature changes and humidity the concept of concrete maturity is commonly used and allows the researcher to see where the concrete was in terms of hydration progress. In general, static testing determines the failure stress that the concrete’s macrostructure can handle, and often failure occurs in the natural materials first or along large defects in casting techniques. Dynamic testing or high strain rate testing, on the other hand, loads materials at such a high rate that larger defects do not have time to react and instead the microstructure is more highly stressed leading to higher strength and stiffness values. This is known as the material’s strain rate sensitivity. Since dynamic testing better tests the microstructural strength, it is believed that it may provide a better way to assess damage to green concrete. Testing includes both static and dynamic compression as well as static and dynamic splitting tensile strength to assess whether damaged has occurred to the concrete. No significant statistical evidence was discovered that damage to the concrete occurred at five different “green” maturities from peak resultant velocities ranging from 10.66 in/s (271mm/s) to 4.40 in/s (112 mm/s) with average intensity of 6.7 in/s (170mm/s).

Jan 1, 2003