Search Documents

By Linghu Changjin

Based on the characteristics of typical marine sedimentary phosphate rock in Guizhou, Southwest China, together with the research findings made on the surface electric properties of pure collophanites taken from different areas in pure water and under the action of collectors, a pure minerals flotation test of collophanite was conducted in this research. The differences of collophanite flotation behavior and the effects of the different pH values, varieties, and dosage of collector on flotation separation of collophanite were studied. It is suggested that that in pure water, collophanite had a negative charge within a wide pH range. The electro negativity values of collophanite increased with the addition of collectors GJBW and WF-01. When GJBW and WF-01 were used as collectors, the collophanite was depressed in acid medium, but had a good flotability in basic medium.

Sep 1, 2012

By Kamalendu Bhunia

With the progressive depletion of known resources of good quality coal and minerals as well as the increasing demand of these minerals by different user industries, the emphasis has been shifted all over the world from selective mining to bulk mining followed by up- gradation to obtain the required quality of concentrate. The column flotation cell is one of the alternatives to reduce the gangue content of fines because of its inherent characteristics viz. easier to operate, low space required, no moving parts etc. A laboratory flotation column is used to conduct experiment. Present work has been undertaken to observe the effect of process variables (gas flow rate, feed/slurry flow rate, and frother concentration) on gas dispersion parameters (gas holdup, bubble surface area flux) in collection zone and to explore the effect of feed (slurry) inlet orientations and gas flow rate on column?s metallurgical performance. The effects of solid particle concentration, size and type (hydrophobic and hydrophilic) of solid on gas dispersion parameters have also been investigated. Test work has been performed in a continuously operating Perspex column (10 cm in diameter and 168 cm in height) using coal, sphalerite and dolomite as solid. Gas hold-up has been measured by phase separation method and mean bubble sizes are estimated from a drift flux analysis. The influence of operating parameters on bubble surface area flux has been discussed. It is observed that gas holdup in collection zone is affected by air as well as feed flow rates and also solid?s type. It is also found that addition of solid decreases the gas holdup and rate of decrease in gas holdup increases when solid concentration increases and particle size increases. Increase in gas flow rate increases recovery in collection zone due to increase in number of bubbles per unit volume of the column. From the experimental results it is evident that cross-current orientation of feed inlet shows slightly better metallurgical performance compared to other orientations. Keywords: column flotation, gas holdup, drifts flux, bubble size, bubble surface area flux, hydrophobicity, and recovery

Sep 1, 2012

By I. Yochev, A. A. Metelev, A. I. Stepanenko, A. P. Purgin, M. G. Viduetsky, A. M. Panshin, I. F. Garifulin

"Pneumatic flotation cells of the KFM series are intended for the concentration of various ores and technogenic materials. The key operating principle of the flotation cells of the KFM series is the preparation of pulp for flotation in blowers, offering the advantage of an accelerated flotation process. This report summarizes the results of the implementation and operation of the KFM cells at Russian and foreign projects in 2015-2017. Their implementation and operation experience confirms the high efficiency of the KFM cells, especially in the head of lead and zinc, copper and zinc, copper flotation processes:head KFM-600 flotation cell recovers from lead-zinc ore (Rudmetal AD modular concentrator) up to 52% of lead in a single stage (without cleaner flotation) in a salable lead head concentrate (grade of up to 76% lead, 2.3% zinc). The flotation cell proved to be much more efficient than originally expected in the process description in the design phase,flotation of the copper-zinc ore from Novo-Shemur deposit (PJSC Svyatogor concentrator) in two KFM- 1400M cells recovers up to 65% of copper and 70% of zinc in a high-grade bulk copper-zinc concentrate containing 12-13% of copper and 25-28% of zinc. The installation of the two cells with a combined capacity of 26 m3 allowed to decommission 4 chambers of FPM-16 pneumomechanical flotation cells with a combined capacity of 64 m3 with a simultaneous increase in the overall ore concentration performancea single KFM-1400M cell (13 m3) recovers from the copper ore from Volkov deposit (PJSC Svyatogor concentrator) 53% of copper into a high-grade copper head concentrate (33.0% of copper). For comparison, the pneumomechanical cell FPM-16 (capacity 16 m3) has almost half as low copper recovery (29.6%) into the head concentrate at a lower grade (30.5% copper)."

Jan 1, 2018

By D. Endara, E. De la Torre, S. Echeverria

"The study was conducted with the sulfide mineral from the province of Zamora Chinchipe. It was characterized physical, chemical and mineralogical, obtaining between its main results a copper concentration of head ore of 0,58 %. The mineral was homogenized and taken to direct closed circuit: rollers mill - vibratory sieve (mesh # 16). Flotation was carried out in two stages: the collective and selective where in each one were performed 6 water recirculation as suggested by the technique used to relate information of a batch flotation to a continuous circuit called cyclic flotation tests (LCT). In the collective flotation (bulk) 2 Kg of mineral were grinded with 10 Kg of balls for 30 minutes and 62.5% of solids, the pulp was taken to the flotation process with solids percentages of 33.3% and pH 7, it was conditioned with 45 g / t of KAX 1%, 50 g/t of Aerofloat 208 and 20 g /t of Pine oil. The concentrate and tailings bulk obtained were filtered separately for the recovery of water and it was recirculated to the next grinding of 2kg mineral. In the selective flotation 1Kg of bulk concentrate was carried to regrind for 40 min, 62.5% percent of solids, 10 g of lime and 5 g of tannin FLOATAN T5, the pulp was taken to the roughing-collection-refining flotation circuit controlling the pH between 10.5 and 11 where conditioning (60 g/t of Aerofloat 208 and 30 g/t of Pine oil) and adding lime to the circuit and FLOATAN according to the procedure. The four fractions obtained from the circuit were filtered; the water was recirculated to the regrind process of the bulk concentrate. In the collective flotation process tends to stability in the fourth recirculating water to obtain a copper content of 4.5% and a recovery of 87%, recirculated water represents 69.8% of all water used in the 6 recycles. In the selective flotation circuit the fifth recirculating of water is the optimal where obtaining a copper content of 13% and a recovery of 72%, recirculated water in the selective flotation circuit represents 95% of the total water used in the 6 recycles."

Jan 1, 2018

By M. Ito

Cobalt-rich ferromanganese crust and nodule ores from seamount areas contain volcanic and sedimentary rocks as substrate or nuclei and these ores require mineral processing to remove the substrate/nuclei rock before smelting. This paper reviews the results of jig separation and air table treatment for the coarse fraction and flotation and hybrid jigging for the fine fraction. Using these techniques substrate/nuclei rock was removed from the cobalt-rich ferromanganese oxide components. The mineralogical properties and metallurgical treatment methods including hydrometallurgical treatment of low grade ore is also reviewed.

Sep 1, 2012

By N. Nehoroshev, P. Solozhenkin, N. Voyloshnikova, A. Pshennikov

"Molecular modeling of clusters of major bismuth minerals, Bi2S3, was carried out whereby molecular models of minerals and reagents clusters were created. Their HOMO and LUMO energy levels were calculated and using known modelling equations, the absolute hardness ?, eV and electronegativity were calculated. The charges of separate atoms of clusters and the change of properties of the minerals were determined which allowed predictions of the flotation properties of raw ores containing rare bismuth minerals. Modeled complexes containing the clusters of minerals and various collectors were constructed, consisting of atoms and bonds within clusters of minerals. Major physical and chemical parameters were determined for the complexes created, including the total and electronic energy. Based on the energy calculations, predictions of the collector efficiency were proposed. The efficiency of collector was established for various thiolic reagents, the compounds of phosphorus (III) and mixtures of reagents. Theoretical results were checked and confirmed against laboratory ore flotation tests. A gold-bismuth-magnetite ore type was studied where gold, bismuth and iron (magnetite) are of industrial interest. The ore contains 2.8 g/t Au, 1.0 g/t Ag, 0.26% Bi, 45% Fe and 1.25% As. Sulphide mineralization can be mainly found in the form of pyrrhotite, pyrite and arsenopyrite. Bismuth can be mainly found in the form of bismuthite and native bismuth. Gold is fine. A flow sheet for Zhelezny Kryazh ore treatment was proposed. This flow sheet consists of grinding to 95-98% -74 µm, sulfide flotation with two cleaner with xanthate addition, cyanidation of flotation concentrate and flotation tailings included treatment with with CaO (6 kg, 6 hours), cyanidation (8 hours) and CIL (8+24 hours). Saleable products are gold doré, bismuth and iron concentrate."

Jan 1, 2014

By B. Courtaud

Uranium plants are generally located quite far from conversion plants, resulting in high transport costs. One way of reducing such costs involves putting more uranium in each drum by increasing the final product?s bulk density, which can be achieved via mechanical compaction of the powder and/or improved precipitation. For most of its plants, AREVA has adopted the latter approach, involving a new precipitation process applicable to all kinds of yellowcake produced (via uranates, uranium peroxide, etc.) that achieves bulk density of 3 for soda uranate, for example, instead of the 1.5-2 density available via conventional processes. At present, this process is being undertaken on an industrial scale and will become the norm for precipitation processes at all AREVA U plants. In addition to producing dense yellowcake, the process also delivers a product with no fines, a spherical particle shape (which allows for high-quality powder flow) and superior post-precipitation filterability

Sep 1, 2012

By Sergey S. Gudkov

In the current climate of changing the approach to mining and treatment of mineral resources, processing technologies are being developed that require little maintenance and are economically as well as ecologically sustainable. This may also involve the development of entirely new ways of ore processing. One promising approach is to use bioleaching for the pretreatment of gold refractory ores to cyanidation. Capital costs for vat bioleaching of concentrates and ores are very high and cannot be applied for small or medium-size deposits. IRGIREDMET JSC carried out bio heap leaching test work on refractory ore samples from three Russian deposits. Following this biological treatment a combination of flotation, vat bioleaching, and cyanidation are used to recover gold. After heap bioleaching, gold recovery was 75-80 per cent. It was found that efficiency of heap bioleaching process depends on ore feed size. High duration of this process is another feature and it lasts for about a year. This process can be also used for carbonates in the combination with other process during which acid generation occurs. The results of our studies have shown that this technology is amenable for refractory gold ores. Its introduction allows an increase gold recovery and to solve a number of environmental problems. Keywords: heap biooxidaton, the refractory of the ores, the degree of oxidation, arsenopyrite, pyrite, CIL

Sep 1, 2012

By Z. D. Tan

The continuous digestion technological conditions of phosphate tailings with high magnesium content in sulfuric and phosphoric mixed acid is studied in this paper. The influences of excess coefficient of sulfuric acid, weight liquid to solid, reaction temperature and time on conversion of P2O5 and MgO are discussed. The influence of infiltration capacity of phosphogypsum by the concentration of liquid-phase SO3 is discussed too. Under the optimal technological conditions, the conversion of P2O5 is 95.56% and MgO 98.63%, the filtration rate of phosphogypsum increases with the increasing of liquid-phase concentration of SO3, the optimal apparent concentration of SO3 is 0.135~0.14g? mL-1 in liquid-phase. The filtration rate of phosphogypsum is 1473kg? m-2? h-1. N-P-Mg compound fertilizer was produced by adding magnesia powder and inflating ammonia in filtering medium.

Jan 1, 2014

By Chenyang Zhang, Zhigang Yin, Jianyong He, Yuehua Hu

"A lot of floatation reagents (collectors, inhibitors and regulators) for the beneficiation of copper ores have been well developed in the past century. However, it is still unclear about the micro interaction mechanism of these flotation reagents with copper ores. In this paper, the interaction mechanism of these flotation reagents with the copper atom on chalcopyrite has been systematically investigated by first principle DFT (density functional theory) calculations. Thirty-four specific common functional groups linked with the same hydrocarbon chain (ethyl) are optimized at a B3LYP/def2-TZVP level, the solvation effect was included with the SMD solvation model. The analysis of the highest occupied molecular orbital (HOMO), the lowest unoccupied molecular orbital (LUMO) and nature bond orbital (NBO) charge of these reagents reveals their potential applications to other types of copper-bearing mineral. Further investigation of the thermodynamics calculations gives more reliable data to screen collectors or inhibitors for copper-bearing mineral. The flotation results from carefully reviewed literatures are in good agreement with the calculation results. This work might also shed new light on the development and discovery of highly efficient and selective flotation reagents with low cost based on the computational methods.INTRODUCTION Froth flotation,(Shean & Cilliers, 2011) a mineral processing approach, is applied to efficiently enrich valuable minerals from the mixture, which is achieved according to the dictinctive surface properties of minerals. In the past century, researchers have develped an aboundant of flotation reagents by extraction or synthetize, and many carefully selected reagents might die in the bench tests or the pilot tests before the pratice.(Bulatovic & SrdjanM, 2007) Generally, it involves a lot of cost and tedious works by conducting flotation tests to screen flotation reagents. Flotation reagents have been boomed robustly with the developing of the organic synthesis.(Liu, Yang, & Zhong, 2017) Reseachers found the specific properties of a reagent are determined by its functional groups and the length of the hydrocarbon, where the functional group is assigned as the adsorption site to adsorb onto mineral surfaces and the hydrocarbon chain is called as a hydrophobic group."

Jan 1, 2018

By P. S. Rao

In 1951, Tata Steel became the pioneer in Asia by setting up its first ever washery in West Bokaro Colliery. The first beneficiation plant used to produce clean coal of 19% ash with chance cone. Feed size of chance washers were -75 mm to +6 mm. The fine coal (-6 mm) were used directly. With change in technology,in 1986,chance cones were replaced by DM cyclones and coal was washed in two circuits. In the coarse circuit -13 mm to +0.5 mm coal was washed in two stages while the fine coal of -0.5 mm was treated in froth floatation cell. With further improvement in the process the higher ash raw coal was feed to produce clean coal of 13% ash. In 1998, DSM cyclones were replaced by scrolled Evolute design cyclone which has Ep of 0.020 to 0.025 ranges resulting in increase efficiency of separation. With the increase in demand of clean coal, lower seam proportion has increased in raw coal production. The washability studies of individual seams indicated large difference in the seam characteristics in terms of washability and specific gravity cut points of the individual seams. So washing all seams together had resulted in frequent change in the character of coal and warrants frequent changes in the operating parameters of the plant in which the separating efficiency comes down and ultimately resulted in yield loss initially. With increase in knowledge and experience in coal washing the solution to this problem was achieved by adopting, seam-wise washing which is enabling process engineers by keeping set point for longer periods there by to enhance the separation efficiency. Keywords: coal processing, froth floatation, steam washing

Sep 1, 2012

The ore studied occurred in the Three Rivers area in China and was a silver-lead-zinc complex ore containing 400.52 g/t silver, 4.77 % lead and 3.47 % zinc. Silver, lead and zinc were the major valuable elements in the ore and copper, cadmium and tin were the associated elements to be comprehensively recovered, whereas arsenic was the harmful element. The element silver occurred mainly in freibergite with small proportion in dyscrasite and other silver minerals. The carrier minerals for silver were mainly galena and oxidized lead minerals and then sphalerite, arsenopyrite and pyrite. The ore contained numerous minerals with complex mosaic texture and the lead and zinc minerals enclosed each other multiply, which made the separation of the minerals in the ore very difficult. Experimental investigation on the beneficiation of the ore indicated that with flotation separation process it was very hard to obtain single lead concentrate or single zinc concentrate that would meet the requirement of market. In the meantime, during the separation process of lead and zinc, silver tended to be dispersed, resulting in a low recovery of silver. Therefore, a rational utilization technique for the ore should be a combined process of bulk flotation to reduce arsenic? sulphating roasting of silver-lead-zinc bulk concentrate-leaching with diluted sulphuric acid to separate silver, lead and zinc. With this process quality lead concentrate containing silver and high grade zinc product and silver product could be obtained. The recovery of silver, lead and zinc in flotation was 85.10%, 84.48% and 82.48%, respectively. The total recovery of silver, lead and zinc in chemical processing was 97.07%(sum of recovery of silver ingot and lead concentrate), 99.61% and 90.93%, respectively.

Jan 1, 2014

By B. Friedrich, A. Weyhe, H. Heegn

"Nickel-metal hydride batteries (Ni-MH) are storers of electrochemical energy, which have a higher specific storage capacity than lead or nickel-cadmium batteries. The demand for Nickel-metal hydride batteries is increasing rapidly since their market launch in the early 1990’s. Today there is no suitable and sustainable recycling process to recover nickel, cobalt and rare-earth metals. The discarded batteries are used today in the steel industry as alloy material because they contain nickel. Cobalt and rare-earth metals (RE) are lost; they are non-recycleable.In a German governmental funded research project, IME Aachen, ACCUREC Mühlheim and UVR-FIA Freiberg are cooperating in processing as well as in creating a feasibility study. The target of this project is the development of a new recycling process for metal recovery from Ni-MH-batteries. The proposed process described in this paper consists of a combination of mechanical, pyrometallurgical and hydrometallurgical processing steps. This process is capable of treating all types of Ni-MH-batteries. After comminution steel and organics are separated. The separated Ni-MH is smelted in an electric arc furnace. The products are a nickel-cobalt alloy and a slag phase enriched with rare-earth oxides for further treatment to ‘mischmetal’. Both the Nickel-Cobalt alloy and the ‘mischmetal’ will be directly used in battery production."

Jan 1, 2003

By G. Mucsi

This paper deals with the laboratory investigation of cathode ray tube (CRT) glass based glass foam, a relatively new product so called ?Geofil bubbles?. The main process engineering material properties of raw materials, such as particle size distribution, moisture content, density and specific surface area are shown. Then the preparation of raw cathode ray tube glass waste is presented including the following steps: crushing in impact crusher, grinding in laboratory scale ball mill, mixing, pelleting and sintering. We found that it was possible to produce foam glass (with proper mechanical stability and particle density) from the investigated waste CRT glass. The material characteristics of the final product strongly depend on the sintering conditions. Optimum conditions were determined particle size fraction was found to be 4-6 mm, temperature 800 0C, residence time 7.5 min. Keywords: waste CRT glass, grinding, pelleting, sintering, glass foam

Sep 1, 2012

By Jan J. Cilliers, Nicolas Barbian, Esther Ventura-Medina

"Froth structure and stability are known to play an important role in determining flotation recovery and selectivity. An industrial sampling campaign was performed to develop a clearer understanding of the effect of flotation variables on froth stability and the role played by the resulting stability on flotation performance.Froth stability was estimated as the fraction of bubbles bursting on the surface of the froth through image analysis and the solids loading on the bubbles at the top surface. It was generally found that high air flowrates resulted in a drop of froth stability showed by a drop in the fraction of air overflowing and a decrease in the solids loading and simultaneously produced low copper recoveries and low concentrate grades. Deep froths only allowed a small fraction of air to overflow and consequently produced low recoveries. An increase from a standard to high frother dosage did not result in a larger fraction of air overflowing, hence producing low recoveries. Likewise, low frother addition only allows low recoveries because the resulting unstable froth cannot support itself. Low aeration was found to be preferential as it allowed high particle loading, therefore high bubble stabilisation, and low gangue entrainment, resulting in the highest flotation performance.Additional laboratory tests were performed to introduce a new stability parameter and to give a clearer understanding of the effect of flotation variables on froth stability. The results confirmed some of the observations made on the plant."

Jan 1, 2003

By Z. Q. He

This paper introduces the structure and working principle of SLon magnetic separator that has excellent performance in iron removal, and summarizes a part of the examples of applications, which applies this machine to remove iron from non-metallic ores, and shows widespread prospect of application of this machine in the purification of non-metallic ores.

Jan 1, 2014

The challenges of nature for the recovery of metals for a sustainable future continue to present in diverse ways. Base metal deposits are becoming lower grade and more complex. Rare earth metal demand is soaring and must certainly be met from new sources outside of China. Precious metals have soared in value due to increased industrial usage and the importance of these metals as financial instruments. Many of the future sources of precious metals are complex and difficult to process. The field of hydrometallurgy plays an important role in providing technology for extraction of these metals for a sustainable future. Selected examples from the base, rare and precious metals fields will be used to illustrate how current developments are providing metals for our future. The recovery of rare earths by beneficiation, leaching, purification, precipitation will be described from a multi-mineral deposit in Canada. The recovery of metals from complex base and precious metal ores may be accomplished using chloride ? assisted high temperature pressure leaching. Finally, by way of example, the enhanced Galvanox? process for treatment of chalcopyrite concentrates using silver-activated pyrite as a catalyst will be illustrated. This process offers a viable alternative to the conventional smelting of chalcopyrite copper concentrates.

Sep 1, 2012

By M. S. Prithvi

Over the decades, mine and mineral processing plant operations for the most part, have been found to have had adverse impacts on the environment. At the same time, mineral processing and mining operations produce mineral products that are indispensable to modern society. Thus, the sector has desirable and undesirable attributes simultaneously. The situation presents itself as a contradiction (i.e.) the mineral processing and mining operations are wanted by society, and at the same time unwanted by society. The existing methods of addressing the issues raised above have evidently not been very successful in reducing the opposition to new projects and to the related activities such as land acquisition. This paper attempts to show the relevance and applicability of TRIZ for addressing the issue. TRIZ, or Teoriya Rezheniya Isobretatelski Zadach, is a Russian acronym meaning Theory of Inventive Problem Solving. TRIZ is a powerful tool that can be usefully applied to resolve such contradictions, using resources usually available within the system of interest. Accordingly, this paper introduces the issue background, followed by an introduction to some key concepts of TRIZ such as the 40 principles, separation principles and directed evolution. The paper goes on to apply the 40 principles to two case studies. The results show that TRIZ could be a useful tool to generate potentially innovative and sustainable approaches. Its most appropriate position would be as a supplement to current decision-making procedures, and as a validation tool to review existing solutions for possible improvements. Keywords: minerals, environment, TRIZ, contradiction, resources

Sep 1, 2012

By Robin J. Batterham

Alumina demand is steadily climbing around the world and is likely to continue to do so for many years. In such a commodity industry, the question arises as to what effort should be expended on innovation, given that for an individual company, the drivers of change are cost and quality as the market demand is essentially assured. This is of course a long-term view. The current conditions are less attractive. In this presentation, we review the broad issues that are considered targets for collaborative development by the industry as recently updated in the alumina industry roadmap published by the International Aluminium Institute in 2010. While they cover areas such as ?mine rehabilitation, residue management and use, alumina production from high sulfur bauxite, bauxite beneficiation, energy efficiency and alternative technologies for alkali and alumina recovery from bauxite residues,? it must be remembered that each refinery is different in terms of the feed material and the circumstances of waste disposal. Of particular interest is the more competitive area of breakthrough technologies. In the presentation, we will consider a range of opportunities that could transform the industry, from relatively near term possibilities such as bauxite activation through possibilities to eliminate crystallization as currently practiced to complete alternatives, such as the use of hyperaccumulating plants. Against this optimism, some of the realities that hold back breakthrough innovation will be presented for discussion.

Sep 1, 2012

By M. C. Harris

"In the flotation process the contact angle is an important indicator of the hydrophobicity of a mineral particle. There is considerable literature showing that the contact angle increases when the chain length of the alkyl group associated with the collector molecule used to render the valuable mineral particle hydrophobic increases. The extent to which an alkyl group interacts with surrounding water molecules is quantified thermodynamically by the excess Gibbs energy. In the present paper it is shown that there exists generally a strong linear relationship between the excess Gibbs energy of the alkyl group associated with the collector and the contact angle. The structure-activity of such alkyl groups is in turn related to the total surface area, molecular volume, the molar volume, molecular weight of the functional groups in the molecule and interaction energies. It is proposed that the demonstrated relationship is indicative of the role which the alkyl group component of the collector, which is attached to the mineral particle, plays in increasing the extent to which water molecules at the surface of the mineral are rejected from the surface thus increasing the contact angle. The relationship between excess Gibbs energy and surface tension is further explored with a view to relating the observations quantitatively to the parameters in the Young equation.INTRODUCTIONThe issue of wettability of materials is of great importance to many industrial applications. Wettability studies usually involve the measurement of contact angles which indicate the degree of wetting when a solid and liquid interact. As is well known the contact angle (O) is the angle between planes tangent to the surfaces of the solid and the liquid at the wetting perimeter which is the zone where the air, water and solid phase merge. When the air bubble attaches to the solid surface there is an increase in the air/solid interface area and a decrease in the solid/water interface area. For attachment to occur the cosine of the contact angle should be less than 1 and this will be promoted if the interfacial surface tension between the air and the solid (? SV) is low. Classically the relationship between these parameters has been expressed through the Young equation (1) for a perfectly flat surface:"

Jan 1, 2018