Search Documents

By Rod Hocking, Nenad Djordjevic, Randolph A. Pax

"Semi Autogenous (SAG) mills exhibit complex interactions between the competing processes occurring inside them. Traditional practice is to measure the operation of the SAG mill at an operating point in terms of its load, power draw, steel load, ore throughput rate, water addition rate and more recently the feed size distribution. However significant departures from standard operating conditions can occur due to changes, for example, in ore hardness, the quest for higher throughputs and mill internal geometry.Fundamental to SAG mill operation are the internal processes that ensure that a given ore throughput and discharge grind size are obtained and maintained. These processes can be measured using non-contact acoustic emissions from the SAG mills which utilise the information rich noise that is generated by the grinding, flow and charge movement inside a mill. Non-contact acoustic in-mill measurements can be used for the validation of discrete element modelling (DEM). The approach being reported in this paper is to model the individual physical processes and then to simulate the assemblage of a physical mill.By modelling the assemblage of steel balls in a 1 m pilot mill and duplicating the experimental arrangement exactly with the PFC3D model, it was possible to replicate the pattern of falling balls in the experimental mill. Furthermore, the key features of the acoustic emission spectrum that was calculated compared favourably to the measured spectrum at low frequencies. The experimental spectrum is shown in Figure 1."

Jan 1, 2003

By Takashi Furuyama, Sukeyuki Mori, Tetsuo Ikejiri, Abel Bissombolo, Yoshitsugu Koga, Masamichi Hata

In Japan, the increasing number of automobiles newly put into circulation is followed by a larger amount of end-of-life vehicles from which valuable metals are being recovered in shredder and related plants. Nevertheless, the processing of these scrapped automobiles which has reach a recycling rate of about 75%, generates a huge volume of waste, locally known as .shredder dust., which is commonly dumped on landfills. The saturation and depletion of valuable disposal sites in the near future, as well as the social and environmental problems related to the accumulation of these residues disposals are a major challenge for the automobile shredding industry. To promote an alternative way for the management of these disposals, the authors have initiated and developed a system for their processing, on the basis that more than 90% of these residues are combustible materials that could be used as refuses derived fuel. The developed processing system points out the mechanical/physical separation of shredded automobiles residues into two streams by means of an ascending airflow passing through a vertical zigzag separator and, the compaction of the light-density fraction of materials (that is about 60% of auto shredder residue recovered as float products and mainly composed of cotton, sponges and light plastics) to form a refuse derived fuel (RDF), the density, calorific value and ignition loss of which are 1.19 g/cm3, 4470 kcal/kg and 60.7%, respectively.

Jan 1, 2003

By Kalle Härkki

Sustainability principles in the minerals industry are now becoming more and more important from the perspective of securing a license to operate and enhancing environmental, economic and social performance. This trend is also setting new challenges for the design and operation of future concentrator plants. It is evident that ore grades are declining and ores are becoming more complex requiring new technology innovations and holistic approach for process optimization. There is a demand for more energy-efficient process technologies especially in comminution that is the major energy consuming unit operation in the process chain. Energy is not only a major source of cost but also contributes significantly to the carbon and environmental footprint. There is also an increasing awareness that more intelligent water management is required for reduction of fresh water consumption and mastering the impacts of process water recycling will cause for process performance. In association with water recycling, tailings disposal is an integral part of concentrator plant representing significant environmental and economic issues to the operation. This presentation will discuss general trends and challenges of future minerals processing plants and how innovative technology solutions and better integration of unit processes in conjunction with intelligent process control would contribute to meeting the sustainability challenges.

Jan 1, 2014

By Osvaldo Bascur

"The Metals and Mining industries continue to be challenged by deflated commodity prices, increased energy costs, decreased quantity / quality of raw materials, and expanded regulatory requirements. In an effort to offset these headwinds, leaders in these industries are now starting to adopt comprehensive information strategies to improve operational efficiency and business performance. These strategies are resulting in competitive advantage and helping to move operating locations down the commodity cost curve. Current information trends are enabling collaboration, analysis, and action across competence centers to ensure corporate sustainability and ongoing profitability. The digital revolution has created a new focus for continuous process improvement and innovations (SIX SIGMA in practice) -one that spans operations, service organization and also customer interaction. With this expanded focus comes the need to improve processes more openly, more iteratively and more collaboratively. This presentation will share examples of how mineral processors have adopted new strategies such as self-serve business intelligence, data mining, cloud computing and internal/external collaboration. Mine to mill integration for grade recovery optimization, mine and mill asset availability and reductions in operating costs examples will be presented."

Jan 1, 2014

By A. Collings, A. Farmer

"Power ultrasound may be used in the processing of mineral suspensions to clean the particle surfaces of oxidation products and fine coatings, mainly through the large, but very localised forces, produced by cavitation, which is the formation and sudden collapse of bubbles in a fluid. Cavitation occurs preferentially at solid surfaces in a liquid: at container walls, inserted objects or suspended particles. When the cavitational bubbles collapse near a solid they do so by forming a very high energy jet directed from the point on the bubble furthest from, and directed towards, the surface of the solid, in effect micro jet blasting.This paper highlights some of the major mineral processes where ultrasonics is beneficial namely: Surface cleaning of detrital mineral particles, where container quality glass sand was upgraded to tableware quality and up to 20% improvements in the sharpness of high tension separation of mineral sands was achieved"

Jan 1, 2003

By A. Saramak

"The paper focuses on problems of atmospheric pollution by the dusts, produced during the course of crushing and grinding processes, and the main objective of investigative programme is an assessment of emission of particulate pollutants for following crushing devices operated in plant scale: impactors, cone and jaw crushers. All crushers operate in aggregate production plants in Poland. In the first stage of investigations there were determined dust emission levels and supporting characteristics for all crushers under investigation. Then there were introduced indices that allow for comparative analysis in terms of dust emission, for devices with different energy consumptions and comminution ratio. It appeared that crushers with high the overall dust emission do not always achieved unfavorable dust emission per comminution ratio or energy consumption. The introduced indices proved their usefulness, because they helped to carry out a comparative analysis among crushers, operating under different technological conditions. It is also easier to assess environmental impact of individual crushing devices, under analysis. Results of investigations also show that environmental impact of different types of crushers is diverse and it is difficult to compare dust emissions of various types of crushers without taking into account technological aspects (like throughput, comminution ratio, energy consumption, and others) of their operations.INTRODUCTION Mineral processing of raw material is a complex process, involving in general operations of size reductions and separation. Depending on the type of specific raw material, the technological circuit may include operations of comminution and size classification. This is a typical circuit for aggregate production. In ore treatment industry the process in much more complicated and include also a metallurgical treatment of ore concentrate – the final product from processing plant stage.In general, regardless the type of raw material, operations of size reduction are present in each technological circuit of mineral processing. Operations of crushing and grinding are an integral part of processing technology, because they play a crucial role in effective treatment of mineral raw materials (Gawenda 2013). Their duty is to liberate the useful minerals from the gangue in ore treatment industry, or to produce the material with the required particle size in case of aggregate processing. Crushing and grinding operations are of a high negative impact on environment and humans. They consume great amounts of energy, what indirectly contributes to higher emission of carbon dioxide CO2. Apart from energy, crushing and grinding device consume significant amount of steel and other metals and alloys due to high wear of working parts and grinding media. This is also of negative environmental impact due to emissions of additional amounts of CO2 in production of steel and other metals required as spare parts for comminution devices."

Jan 1, 2018

By Stephen Gay, Dewetia Latti

"When improving a plant a mineral processing engineer would like to know the mineral composition distribution. In order to assess this distribution in particles, as compared to the corresponding distribution in particle sections, a procedure needs to be applied to the observed particle sections. Such a procedure is called a stereological correction. There exists many stereological correction procedures, but one group of such procedures is based on using those stereological equations that do not require making assumptions regarding particle shape or texture.In particular Davy derived an equation to estimate the covariance of mineral composition distributions for particles from both particle sections and linear intercepts. Furthermore, this covariance can also be used to measure the variance of the composition distribution of each mineral.This paper shall present results verifying this equation. The experimental method was based on obtaining particle information from serially-sectioned particles. Particle samples selected for serial sectioning displayed a range of natural textures including liberated, binary and composite particles. The exposed surface of the polished sections were analysed using QEM*SEM. This procedure was repeated until all of the grains have been polished away. The covariance of mineral distributions were calculated from the serial sections and compared with that calculated using Davy’s equation."

Jan 1, 2003

By Vladko Panayotov, Marinela Panayotova

"Recently, in order to extract metals, the industry is trying to process old metallurgical slag. The material requires very fine grinding that results in enhanced slime-formation. This in turn leads to problems in the course of the flotation process and to a loss of metal. In addition, it causes difficulties in the wastewater treatment aimed at water reuse. The aggregation and separation of the fine particles and their further subjecting to mineral processing would result in more efficient use of raw materials. Closing the water cycle also would be facilitated. The paper presents results from studying sixteen flocculation reagents, commercially available for treating municipal wastewater, including products based on nanotechnology, for their ability to rend the production wastewater in suitable for reuse in the flotation. It turned out that, from all studied reagents, the cationic C-587 is suitable for the purpose. Some of reagents were studied for their ability to flocculate selectively, in presence of coke fines, rich in copper fines which are produced at grinding of a slag from lead-zinc metallurgy. Most promising reagents are chosen, based on the chemical analysis of the flocculated materials. Open-cycle rough copper flotation experiments with the flocculated fines and recycled wastewater gave encouraging results."

Jan 1, 2014

By Rainer M. Lotzien, Michael J. G. Battersby, Jan Kleefeld, Julian V. Brown, Rainer M. Imhof

A new flotation system has been developed to improve the generally slow separating differentials of fine bubbles and fine particle suspensions. The new technology is based on established pneumatic flotation designs called Imhoflot which use intensive in-line pre-aeration to aerate the flotation pulp prior to its introduction to the separating cell. In the new system (see figure 1) this separation is speeded up dramatically by the introduction of centrifugal motivation in the separating vessel, without the use of internal moving parts. The design focuses on providing increased differential forces on buoyant mineralised bubbles and hydrophilic fines. The commercial benefit to industry is much reduced residence time, less than 30 seconds, which offers considerable cost savings in equipment and infrastructure.

Jan 1, 2003

By Aldo Cipriano, Fernando Estrada

The mining industry is in search of control strategies that allow considering a global optimization of their processes, ensuring their stability. This has led to the application of recently developed control techniques on large-scale systems in the mining processes. One of the most important process of the mining industry is the mineral grinding, as the product particle size impacts, in a significant manner, the recovery rate of the valuable mineral in the separation stages. As a solution, a centralized hybrid model predictive control (HMPC) is presented; this control approach maintains the product particle size on a defined range and minimizes energy consumption, maintaining the grinding plant in a stable operation. As a comparison, a conventional model predictive control with an expert system to handle discrete events was developed, showing HMPC is a suitable solution that can used in the grinding process, with the benefit that it handles in the same controller both discrete and continuous dynamics and events.

Jan 1, 2014

By Erico Tabosa, Meng. Jun, Kym Runge, Matthew Brennan, Weiguo Xie, Dee Bradshaw

Turbulence and its distribution are of great importance in flotation cell design as they affect suspension of particles, air dispersion and particle-bubble collision rates, which in turn determine flotation performance. However, there is no mature technique to measure turbulence in three phase (liquid-solid-gas) systems such as in flotation cells. In this article, the authors present two new approaches that are suitable for measuring turbulence distribution in three phase systems and validate their applicability. The first technique uses a piezoelectric vibration sensor (PVS) to measure fluid kinetic energy standard deviation and the second technique applies electrical resistance tomography (ERT) to measure conductivity variation at a measurement position in a flotation cell. For the PVS technique, calibration of the sensor was performed to determine the values of parameters that were needed to calculate the force applied to the sensor. Then measurement was conducted in a 60L batch flotation cell and the results were compared with LDA measurement. This demonstrated that the piezoelectric sensor signal provides a good representation of fluid kinetic energy standard deviation at the position of measurement. For the ERT technique, conductivity distribution data was processed to give conductivity variations, which were then used to calculate fluid kinetic energy standard deviation at the measurement position. The spatial distribution of turbulence obtained by performing multiple measurements at different positions in the 60 litre batch flotation cell was found to agree with the PVS measurement results. These two techniques are potentially powerful tools for turbulence measurement in flotation environments, enabling a clearer understanding of turbulence’s influence on flotation performance to be determined.

Jan 1, 2014

By M. Schneider, J. Regler, Th. Neesse, AKW A. + V GmbH & Co., J. Dueck, F. Donhauser

"In practice the advantages of high-quality hydrocyclone separation are often reduced due to varying feed suspension properties, solids concentrations and particle size distributions. Therefore, a new control system for a battery of hydrocyclones with a nominal diameter of 150 mm was developed for bentonite slurry regeneration associated with tunnel excavation using bentonite slurry as a transport aid and lubricant.As can be seen from Fig. 1, the hydrocyclone battery has been modified for regulation purpose. The battery was manufactured with an overflow collector as a closed pressure chamber (1) with a discharge pipe (2) where the throttling valve (3) was installed.With increased stepwise throttling of the overflow, the volume split is changed with the effect that the solids discharge in the underflow is increased. To stabilize the total throughput, the feed pump speed is simultaneously increased so that the pressure drop ?p across the hydrocyclones (9) remains approximately constant. However, this causes the increasing pressure inside the hydrocyclones, which results in a further intensification of the underflow discharge. After the detection of the break through of the air core (transition state) by the capacitive sensor (4), the throttle valve is shortly opened, and a new regulation interval can start again. The control concept is focused on maintaining the optimum operating state, characterized by the underflow discharge shape at the transition state between rope and umbrella discharge."

Jan 1, 2003

By Lev Malytin, Alexander Dyachenko, Roman Kraydenko

"A new method of processing beryllium raw materials based on interaction of beryllium mineral with ammonium fluoride was developed. Possibility of extracting ammonium tetrafluoroberyllate from bertrandite and phenakite minerals is proved. The developed technology allows replacing the outdated sulfate technology developed by Materion Corporation. INTRODUCTION Beryllium is a strategic metal, which is produced only in three countries: the USA, China and Kazakhstan. The world production of beryllium amounts to only 300 tons per year. More than 75% of the world beryllium production is manufactured from oxide beryllium ores in the USA by Materion Corporation. In Russia there is a large-scale beryllium ore deposit «Ermakovskoye» containig over 1 million ton of ore. Concentration of beryllium in ore amounts to 1,2%. Since the mineral base of ore is calcium fluoride, the sulfate technology of Materion Corporation cannot be used. After alloying and sulphuric acid leaching the fluorine-ion found in fluorite and beryllium together evolve into the aqueous phase. At the stage of Be(OH) precipitation fluoride-ion prevents complete isolation of beryllium into the phase of hydroxide, which increases the loss of beryllium. A new ammonium-fluoride method for processing high-fluoride beryllium ores has been developed at Tomsk Polytechnic University. The ammonium-fluoride method involves fusion of ammonium fluoride (NH4HF2) with a beryllium concentrate. The concentrate containing 10% of beryllium oxide and 25% of calcium fluoride is produced by flotation from the ore of Ermakovskoe deposit. The main component of the ore concentrate is fluorite CaF2, which does not react with NH4HF2. Beryllium in this concentrate is represented by two minerals: phenakite Be2(SiO4)2 and bertrandite Be4[Si2O7](OH)2. Ammonium fluoride, unlike sulfuric acid, does not react with calcium fluoride and is not consumed for decomposing the mineral base of the concentrate. Ammonium fluoride is an accessible and environmentally safe reagent, worth up to $ 1,200 per ton. The total amount of ammonium fluoride is recycled and is used for decomposing a new batch of beryllium concentrate."

Jan 1, 2018

By Lev Malytin, Alexander Dyachenko, Roman Kraydenko

"A new method of processing beryllium raw materials based on interaction of beryllium mineral with ammonium fluoride was developed. Possibility of extracting ammonium tetrafluoroberyllate from bertrandite and phenakite minerals is proved. The developed technology allows replacing the outdated sulfate technology developed by Materion Corporation. INTRODUCTION Beryllium is a strategic metal, which is produced only in three countries: the USA, China and Kazakhstan. The world production of beryllium amounts to only 300 tons per year. More than 75% of the world beryllium production is manufactured from oxide beryllium ores in the USA by Materion Corporation. In Russia there is a large-scale beryllium ore deposit «Ermakovskoye» containig over 1 million ton of ore. Concentration of beryllium in ore amounts to 1,2%. Since the mineral base of ore is calcium fluoride, the sulfate technology of Materion Corporation cannot be used. After alloying and sulphuric acid leaching the fluorine-ion found in fluorite and beryllium together evolve into the aqueous phase. At the stage of Be(OH) precipitation fluoride-ion prevents complete isolation of beryllium into the phase of hydroxide, which increases the loss of beryllium. A new ammonium-fluoride method for processing high-fluoride beryllium ores has been developed at Tomsk Polytechnic University. The ammonium-fluoride method involves fusion of ammonium fluoride (NH4HF2) with a beryllium concentrate. The concentrate containing 10% of beryllium oxide and 25% of calcium fluoride is produced by flotation from the ore of Ermakovskoe deposit. The main component of the ore concentrate is fluorite CaF2, which does not react with NH4HF2. Beryllium in this concentrate is represented by two minerals: phenakite Be2(SiO4)2 and bertrandite Be4[Si2O7](OH)2. Ammonium fluoride, unlike sulfuric acid, does not react with calcium fluoride and is not consumed for decomposing the mineral base of the concentrate. Ammonium fluoride is an accessible and environmentally safe reagent, worth up to $ 1,200 per ton. The total amount of ammonium fluoride is recycled and is used for decomposing a new batch of beryllium concentrate."

Jan 1, 2018

By V. M. Bystritsky, M. G. Sapozhnikov, G. M. Nikitin, A. B. Sadovsky, Yu. N. Rogov

"At present kimberlite ore is processed in crushers or grinding rolls with subsequent grinding in wet mills down to a size of 0.2 mm. The basic disadvantage of the standard diamond processing technology is that crushing kimberlite ore can damage the most valuable large diamonds of few carats. Tagged neutron method offers a possible solution to this problem. It allows detecting diamond inside kimberlite ore without its disruption. The results of the tests of the neutron separator prototype carried out at the Lomonosov processing factory of PJSC Severalmaz are discussed. The possibility to detect the diamond in the rock whose size is 10 times larger than the size of the diamond is demonstrated.INTRODUCTION At present standard diamond processing technology implies disintegration of kimberlite ore in crushers or grinding rolls down to a size of 0.2 mm. It inevitably leads to high probability that large and most valuable diamonds could be damaged. The fraction of diamonds which lost integrity in the process of ore enrichment could be as large as 35-65% [1]. Tagged neutron method (TNM) [2] offers a possible solution to this problem. It allows detecting diamond inside kimberlite ore without its disruption. The main idea of the TNM is irradiation of an object by fast 14.1 MeV neutrons from binary nuclear reaction d + 3H ?4He + n (1) and detecting (tagging) the 4He (a-particle) that accompanies neutron. That gives possibility to determine direction of the neutron momentum. Those tagged neutrons irradiate kimberlite ore under investigation and produce gamma rays via inelastic scattering reactions with nuclei"

Jan 1, 2018

By Brochot. Stephane, Manuel Gonzalez Fernandez

"HPGR (High-Pressure Grinding Rolls) is widely used today for grinding of various kinds of ores such as iron ore or base and precious metal ores. It can be used as first stage of grinding replacing tertiary crusher and SAG mill, but also as regrinding stage to enhance mineral liberation. In addition to better energy efficiency, the advantage of HPGR is to produce much more internal particle fractures allowing faster leaching as it has been demonstrated for some gold ores. This grinding mode of compression and fracture generation also promotes mineral liberation without overgrinding. Mineral processing modelling and simulation associated to detailed ore characterization constitute a powerful tool for plant design and optimization. The mathematical models of the units of operations (grinding and separation) have to reproduce the mineral deportment for which the mineral liberation plays a central role. The present paper is focused on the HPGR modelling with the objective of plant optimization or advanced design from pilot plant tests. The traditional approach of the population balance linked to the energy dissipation and the residence time distribution is generalized in association with a mineral liberation model. The effect of the specific HPGR breakage matrix and grinding function on the mineral liberation rate is discussed and compared to the tumbling mill. The implementation of this mathematical model into a plant simulation tool is illustrated by the example of the optimization of an iron ore concentrator."

Jan 1, 2014

By W. G. Wu

More and more researches and applications of organic chelating agents as depressors or activators are carried out in the course of research and application of modern flotation. The paper puts forward the necessary condition of organic chelating agents as depressors or activators by analyzing the chelating chemical performance of organic chelating agents with metal ions and the stability of chelates formed by them; at the same time, puts forward four sufficient conditions of organic chelating agents as depressors or activators according to different hydrophilic capability of the chelates and different performance of depression and activation of organic chelating agents for minerals. Namely, the ?1+1/4? necessary and sufficient conditions of organic chelating agents as depressors or activators are put forward.

Jan 1, 2014

By P. Radziszewski

In comminution research, ore breakage and wear are usually studied independently of one another. Much of this is due to the fact that wear is usually a slow process compared to ore kage. However, the abrasion wheel test used to determine the abrasive wear contribution to total steel media wear provides the opportunity to study not only abrasive wear and friction but also ore breakage. In this paper, we will explore the use of the abrasion wheel wear test device to study abrasive wear, friction and ore breakage using standard Ottawa foundry sand. We will look into the feasibility of applying the work index as well as t10methodologies to this test set-up. We will also look at how the work index results evolve with abrasive wear and friction. We will then discuss the merits of pursuing the use of this abrasion wheel test for not only wear characterization but also breakage characterization.

Jan 1, 2014

By D. Saramak

"High-pressure grinding technology is considered as one of the most efficient techniques of ore comminution, especially in terms of energy consumption. HPGR devices has been utilized in many mining-related industrial sectors, including iron and non-ferrous metal ores processing (copper, platinum, gold), as well as cement and limestone flour production. Even though the technology well known (introduced into mineral processing circuits in 80’s), there are still examples of ineffective operation of HPGR devices. This is a result of improper application of HPGR into individual crushing circuit. The purpose of the paper was to analyze selected effects achieved in HPGR on the course and effectiveness of beneficiation operations. Investigations were carried out for copper ore, and investigative programme was run for different values of HPGR pressing force, as well as changeable ore characteristics (content of fine size fractions, material moisture). All crushing products were then treated in flotation process, in order to determine useful mineral recovery. Results of investigations show that HPGR operating pressure influences the metal recovery in proportional way, however too extensive pressure values have relatively lower impact on increasing of the metal recovery. Particle size distribution of HPGR feed and its moisture have lower influence on recovery level than HPGR pressure, but too extensive moisture content influences the higher energy consumption of the roller press, together with less effective comminution. The second aspect raised in the paper was a possibility to control and optimize the HPGR-based circuit. There were presented the proposed approach to adjustment of HPGR operating parameters that enables the higher metal recovery.INTRODUCTION The high-pressure grinding technology, invented and developed by Professor Schoenert in 70’s (Schoenert, 1979), is currently regarded as one of the most efficient methods of hard ore comminution. Since then the technology was introduced into raw materials treatment circuits in many mining and mining-related industrial sectors, including iron and non-ferrous metal ores processing (copper, platinum, gold), as well as cement and limestone flour production. Considerable number of works concerning modeling and optimization of HPGR operation were also presented (Daniel & Morell, 2004, Tavares, 2005, Saramak, 2012, Saramak & Kleiv, 2013). Nowadays high-pressure grinding rolls devices are considered as well know technology with over 500 sold machines, according to various sources."

Jan 1, 2018

By M. E. Ramírez

In this research bioleaching or extraction of iron present in a kaolin from La Virgen mine, Anti-oquia/Colombia, was carried out. Organic acids produced in SF with Aspergillus niger were used in the process. The fermentation process was carried out in 3 L aerobic stirred bioreactors, at a temperature of 30 °C, a stirrerd speed of 700 rpm, an initial pH of 4 and a fermentation time variable between one to 8 days, obtaining broth fermentation samples daily per bioreactor. For iron extraction, fermented broth from second to sixth day of fermentation was evaluated and it was found that the fermentation broth of the third day showed a larger potential for iron removal, 786 ppm, by using kaolin with an initial iron content of 1401 ppm. A set of tests using commercial organics acids such as citric acid and oxalic were carried out because those were found in the fermentation broth and it was found that oxalic acid presented three times more iron removal than citric acid.

Jan 1, 2014