Search Documents

By Kevin P. Plucknett, Z. Memarrashidi

"In the current work, factors influencing the corrosion mechanisms of TiC and Ti(C,N) based cermets are reviewed. Cermets were typically prepared with 30 vol.% of metal binder, in the form of various in-situ reaction-formed Ni3Al alloys. Commercial WC-Co hardmetals were also examined as baseline materials. The assessment of corrosion involved a variety of electrochemical measurements, including open circuit potential and potentiodynamic polarisation. The corrosion potential and current density were determined, following Tafel extrapolation, allowing estimation of the corrosion rates. Post-corrosion characterisation involved scanning electron microscopy analysis and associated energy dispersive X-ray spectroscopy of the sample surfaces. It is demonstrated that the primary corrosion mechanism for this type of cermet is dissolution of the metallic phase during oxidation attack, and thus this response can be expected to increase with the amount of binder in the cermet, although degradation can be subtly affected by composition (i.e. alloy composition, C:N ratio, impurities in the ceramic phase, etc.) and test procedure (i.e. aerated vs. de-aerated electrolytes). It was observed that addition of N content into the ceramic phase is beneficial to the corrosion characteristics of TiC based cermets, through significant refinement in the grain size of the hard phase. Similarly, elimination of impurities, such as W in selected TiC powders, also improves the corrosion resistance.INTRODUCTION Cermets are prepared using the combination of a hard, high elastic modulus ceramic phase with a ductile, high toughness metallic binder. This pairing of hard and ductile components ensures wide application of cermets in demanding wear environments. These materials are consequently used industrially in both bulk and coating form. The most common example of such a composite system is based on the use of tungsten carbide with a cobalt-based binder (WC-Co), which has been widely examined over the past 80 years. However, while WC-Co has been shown to exhibit an excellent combination of high strength and wear resistance, the corrosion and high temperature properties of this material are relatively poor. In addition, WC-Co possesses a high density (~13–14 g/cm3), which makes it a less desirable option when the component mass is a design factor (i.e. use in aerospace). In particular, the aqueous corrosion response of WC-Co limits its use in wear environments where combined corrosive degradation may occur (i.e. tribo-corrosion scenarios). Alternate cermet systems are therefore being actively developed due to these performance limitations."

Jan 1, 2017

By G. Robert Guillet

"Ontario enjoys the advantage of its proximity to the large industrial market of northeastern North America. Together with Quebec and fifteen nearby U.S. states, an industrial base of more than half the total for both countries is provided by a population of 100 million.Mineral fillers such as barite, calcium carbonate, kaolin, mica, silica and talc are of major importance in the manufacture of paper, paint, plastics, rubber, vinyl tile, carpet backing, putty, caulks, sealants and adhesives. Ontario has all of these minerals, but domestic production falls short of demand in some cases, and mica and kaolin are not produced at all.This paper reviews the market and outlines the distribution of the major filler-consuming plants of northeastern North America. It also identifies the principal producers of filler minerals in the United States and Canada.IntroductionOf all the uses for industrial minerals, mineral fillers are probably the least understood. Originally used primarily to add low-cost bulk to a variety of commodities without seriously affecting their properties, filler minerals have become essential components that enhance and extend the properties of their hosts. Hence the term ""extender"" which, for all practical purposes, is synonymous with ""filler"". Today, fillers and extenders are not solely low-cost additives, but ingredients that provide essential characteristics to the products they fill.The major markets for mineral fillers are paint, paper, plastics, rubber, adhesives and floor coverings. But there are many others: putty, pesticides, wire and cable coatings, caulking and asphaltic compounds, oilcloth, wall-paper, joint cements, inks, sealants and many others. Barite, calcium carbonate, kaolin, mica, silica and talc are among the more important filler minerals discussed in this paper, but there are at least a dozen others. And the increasing practice of coating the mineral surfaces with certain coupling agents or metal stearates is constantly expanding the range of characteristics and hence the marketing opportunities.Whiteness, particle shape, fineness of grind and cost are the principal considerations in selecting a filler, but other characteristics such as weight, opacity, hardness and chemical inertness may be dominant considerations in specific applications."

Jan 1, 1987

By Carlos Alberto Spier

The Águas Claras and Pico mines are two world-class, iron-ore mines hosted within Lower- Proterozoic banded iron-formations (locally known as itabirites) of the Minas Supergroup located in the Quadrilátero Ferrífero District, Minas Gerais, Brazil. The Águas Claras orebody consists of a 2,500 m long roughly tabular-shaped lens hosted within the dolomitic itabirite of the Cauê Formation. Dolomitic itabirite is the protore of the soft high-grade iron ore, which is the main ore type of the Águas Claras orebody, and represents more than 85% of the 284 Mt mined since 1973. Hematite is the main constituent of the iron ores. It occurs as martite, granular hematite and, locally, as specularite. Magnetite appears subordinately as relicts within martite and hematite crystals. Gangue minerals are very rare. These consist of dolomite, chlorite, talc and apatite and are especially common close to the contact with the protore. This virtual absence of gangue minerals is reflected in the chemistry of ores which are characterized by very high Fe contents (an average of 68.2% Fe). The Pico orebody is a continuous ~3,000 m long body of lenticular shape hosted within quartz itabirite, which is the protore of the soft high- and low-grade ores at the Pico mine. The soft high-grade ores, together with the low-grade ores, called iron-rich itabirite, are the main types of ores at the Pico mine, respectively representing approximately 51 % and 29 % of the reserves within the pit. The iron oxide mineralogy is the same as that of the Águas Claras mine, but in different proportions. Gangue minerals are very rare in the high-grade ores, but are slightly more common in the iron-rich itabirite. Quartz is the dominant gangue mineral, and is found with minor quantities of chlorite. The chemistry of the high-grade ores is characterized by high Fe contents (an average of 67.0 %) and low P, Al2O3, and SiO2 which are concentrated in the fines. Iron rich itabirites average 58.6% Fe and 13.5% SiO2.

May 1, 2003

By Stanislaw Trenczek

Natural hazards such as rock bumps, methane, coal dust explosions, airborne respirable dust, outbursts of gas and rocks, water, radiation caused by natural radioactive materials, spontaneous fires, and climatic hazards, occurring in the Polish hard coal mines, should be controlled. These hazards are characterized by different scale levels numbered from 2?5. To recognize the amount and levels of hazards, research works were carried out in 109 mining districts of mines belonging to Jastrzebska Spólka Weglowa, Katowicki Holding Weglowy and Kompania Weglowa. These are 86 % of all mines and could be regarded as representative of the majority of Polish mining. The hazards have been classified as regards the frequency of their occurrence as: commonly occurring ? with a frequency of 100 % (like airborne respirable dust and fire hazards), high occurrence frequency ? frequency from 60 to below 100 % (methane hazard ? 83.5 %, coal dust explosion hazard ? 92.0 %, and water hazard ? 99.1 %), medium occurrence frequency ? from 30 to below 60 % (rock-bump hazard ? 52.3 % and climatic hazards ? 51.4 %), and episodic occurrence frequency ? below 30 % (outburst of gas and rocks and radioactive hazards). The dynamics of effects of growth in hazard levels to their intolerable values is diverse. Some of them are passive in nature, which allows for longer observation of changes and appropriate early response (as for climatic and spontaneous fire hazards). However the majority of them take on the character of disasters, like methane or coal dust explosions and damage of the excavation structure ? as occurs after a rock-bump or rock outburst; and creation of an atmosphere unfit for breathing ? during open or spontaneous fires, or after gas outbursts containing methane. There are also latent hazards whose effects do not influence indeed a process of production; however they are detrimental to health when a worker is exposed for a long time to airborne respirable dust and radiation. For other types of hazards a level of danger may be only estimated. Since the systems monitoring allows a wider range of control, therefore, aside from rock-bump and methane hazards, there are monitored also fire hazards including measurements of other air parameters (velocity, pressure, humidity, temperature, O2, CO2 concentration). A few types of monitoring systems are used in Polish mines, like the monitoring systems for environmental parameters such as SMP-NT, SMP-NT/A, the telemetric systems CST-40, CST/A, including the computer-aided system for methanometry control officer SWµP, the computer-aided measuring systems KSP-1, KSP-2, KSP-2C, or the production and safety control system VENTURON. The underground part of the systems monitoring of natural hazards contains measuring devices and equipment for automatic control (power-off) of machines and electric devices in case of increased methane hazard. The surface part of the monitoring system allows the measuring data to be visualized and pre-alarm (warning) and alarm states to be displayed. Furthermore it makes it possible to archive and report the data and to control the underground supply and signalling devices. The EMAG Institute developed monitoring methods to extend a measuring range of monitored parameters (such as methane and fire hazards) as well as to monitor so far unmonitored hazards like dust hazards (by continuous monitoring of dust levels in mine air) and climatic hazards (by online monitoring climatic parameters of mine air).

Aug 1, 2013

By David McMullen

Radiation plays a critical role in the thermal behaviour of hydrometallurgical process equipment. This effect is particularly important when designing refractory lined equipment used in pressure leach/oxidation processes. In order to simplify this non-linear mode of heat transfer, the effects of radiation had previously been incorporated in an equivalent convective film coefficient in finite element methods (FEM). This prior method omits the effects of radiosity, a critical aspect of radiation heat transfer, which affects the design of refractory lining systems in autoclave vessels. Given that 60% of the heat loss in actual plant practice of an autoclave is due to radiation, reliability in the FEM is therefore impacted. This study validates the use of radiosity in FEM through thermal loading using a combination of simple geometries to be applied to complex environments such as vessel nozzle clusters. The added benefits of using a radiosity load includes an increase in confidence in thermal distribution results, greater accuracy in determining appropriate refractory lining systems, weld overlay sizing, and increased accuracy in structural analysis.

Jan 1, 2014

By G. Goodall, D. Mercier, M. Brochu, C. Kaplin

A nanostructured CoNiCrAlY coating was obtained by thermally spraying cryomilled feedstock powder using the high-velocity oxy-fuel (HVOF) process. The oxidation behavior of the nanostructured powder and coating were compared to their conventional counterparts by performing static oxidation tests at 1000°C for durations ranging from 1 to 96 hours. It has been found that oxidation of the conventional powder yielded a duplex oxide scale composed of an inner layer of Al2O3 and an outer layer composed of Cr2O3, NiAl2O4 and other spinels. Interestingly, oxidation of the as-sprayed nanostructured coating yielded a similar duplex oxide scale while oxidation of the polished coating resulted in a single Al2O3 layer. These findings indicated that surface oxide seeds act as nucleation sites for the growth of the mixed oxide layer. Also, it was determined that nanostructuring of the coating promotes the nucleation and growth of a single and adherent a-Al2O3 layer by increasing both the number of diffusion channels and the aluminum concentration at grain boundaries.

Jan 1, 2010

By Glenville A. Collins

IN 1932, Horace Onyett at Oroville, California, built a practical floating washing plant along the general lines as now known, using a 24 in. by 12 ft. trammel; it was fed with a ½ yard dragline bucket, rated then at 200 yards per day. Onyett dubbed his plant a 'Doodlebug' which name has clung to this type of operation ever since. In general, the 'Doodlebug' dredge is the outgrowth of the depression of 1929, wherein many dirt contractors had surplus idle equipment and a few of them ventured to use it for placer mining. Many such plants were impractical and poorly designed and adapted often to locations not suited to the purpose. However out of the general idea came refinements until today dragline dredging has a very definite place in the gold production of the world. Many of the early operators, being mainly contractors without mining experience or technical knowledge of gold saving, geology, or mechanical design, naturally went through stages of trial and error until a workable unit became standard practice. Credit should be given Bodenson Iron Works of San Francisco, who did a notable job of pioneering and building of floating washing plants; also, to Lord and Bishop, contractors of Sacramento, who were among the early operators, and to several others who built and rebuilt their plants until the weak spots were strengthened to take the beating required, and yet deliver a high degree of efficiency.

Jan 1, 1945

By D. J. W. Piper, T. Hundert, G. Pe-Piper

"Abstract - Potentially commercial deposits of kaolin are found in the fluvial Lower Cretaceous Chaswood Formation, the sedimentologically proximal equivalent of deltaic sediments of the offshore Scotian basin. The geological setting of the kaolin deposits has been interpreted from high-resolution seismic-reflection profiles and boreholes, and mineralogical studies on one reference borehole. The kaolin is a product of early diagenesis involving meteoric water below the water table. The distribution of kaolin is controlled by the presence of intraformational unconformities that were sites of ground water recharge, and are marked by the development of oxisols above the water table. Such diagenesis was facilitated by interbedded, loosely consolidated, permeable sandstone. The highest-grade kaolin deposits are found in areas close to river belts, where overbank muds were not sufficiently drained to develop paleosols, but where later uplift created intraformational unconformities. In the sandstone, meteoric water flow altered feldspars to kaolin, thus yielding commercial silica sand deposits. It also altered ilmenite to rutile, which is concentrated as secondary placers in modern rivers that have eroded the Chaswood Formation and tills derived therefrom. Sommaire - Des dépôts de kaolin potentiellement économiques ont été notés dans la Formation de Chaswood d'’âge Crétacé Inférieur, laquelle constitue un équivalent latéral en milieu fluviatile aux sédiments deltaïques du bassin de Scotian. Le contexte géologique de ces dépôts de kaolin a été interprété a partir de profils de seismique-réflection à haute résolution, de sondages, et d’études minéralogiques sur un sondage de référence. Ce kaolin est un produit diagénétique précoce formé par de l’eau météorique sous le niveau de la nappe phréatique. La distribution du kaolin est contrôlée par la présence de zones de recharge associées à des discordances intraformationelles marquées par le développement d’oxisols au-dessus du niveau de la nappe phréatique. La présence d’interlits de grès perméables faiblement consolidés a contribué à l’efficacité de ce processus diagénétique. Les dépôts de kaolin les plus riches se trouvent en périphérie des rivières, là ou les boues de la plaine d’inondation n’étaient pas suffisamment bien drainées pour permettre le développement de paléosols, mais où des mouvements verticaux subséquents ont crée des discordances intraformationelles. La circulation d’eau météorique dans les grès a entraîné l’altération des feldspaths en kaolin, générant ainsi des dépôts économiques de sable de silice. Elle a aussi causé l’altération de l’ilménite en rutile, que l’on trouve dans des placers secondaires situés dans des rivières contemporaines qui ont érodé la Formation de Chaswood et les tills qui en sont dérivés."

Jan 1, 2006

By G. Roy, D. R. Lentz, A. O. Wills

"Abstract - Diamond-drill hole DDH-B357, located 1.5 km north of the Brunswick No. 6 Zn-Pb- Cu-Ag volcanic-sediment-hosted massive sulfide (VSHMS) deposit, intersects three exhalative horizons within variably altered felsic volcanic rocks of the Nepisiguit Falls and Flat Landing Brook formations. These three petrographically indistinguishable iron formation intervals (Fe2O3T = 21.4 wt.%) likely represent cogenetic hydrothermal sedimentary units because they display a common geochemical signature: Fe2O3T = 42.9 ± 10.5 wt.%, MnO = 5.4 ± 3.1 wt.%, elevated base metal values (Zn+Pb = 1999 ± 1091 ppm), strong enrichment in additional exhalative components (CaO = 5.3 ± 3.9 wt.%; P2O5 = 1.43 ± 1.00 wt.%), oxidized signature (Fe/Mn = 10 ± 6), as well as a common immobile element signature (Zr/TiO2 = 0.025 ± 0.007) representative of a pelagic source. The calc-alkaline to transitional host volcanic rocks can be discriminated by Zr/TiO2, and to a lesser extent by Th/Nb: Nepisiguit Falls Formation: Zr/TiO2 = 0.053 ± 0.004, Th/Nb = 1.08 ± 0.37; Flat Landing Brook Formation: Zr/TiO2 = 0.107 ± 0.043, Th/Nb = 0.86 ± 0.17. A symmetrical repetition of the footwall-iron formation-hanging wall stratigraphic sequence is observed in DDH-B357, with distinct felsic volcanic rock domains separated by the three iron formations. This is best explained by parasitic F2 folds on the west flank of the south-plunging Brunswick antiform, similar to the fold closures known to host massive sulfide accumulations in the Brunswick No. 6 and No. 12 mines. Iron formation geochemistry and felsic volcanic rock chemostratigraphy from drill core sampling can provide an effective mineral exploration tool for the structurally complex rocks of the Bathurst Mining Camp. Sommaire - Le forage au diamant DDH-B357, situé à 1.5 km au nord du gisement de Sulfures Massifs à Encaissant Volcanique et Sédimentaire (SMEVS) de Zn-Pb-Cu-Ag Brunswick No. 6 recoupe trois horizons exhalatifs au sein des roches volcaniques felsiques diversement altérées des formations de Nepisiguit Falls et de Flat Landing Brook. Ces trois intervalles de formation de fer, impossibles à distinguer pétrographiquement les uns des autres, représentent vraisemblablement des unités sédimentaires hydrothermales cogénétiques sur la base de leur signature géochimique commune: Fe2O3T = 42.9 ± 10.5 % poids, MnO = 5.4 ± 3.1 % poids, des teneurs élevées en métaux usuels (Zn+Pb = 1999 ± 1091 ppm), un fort enrichissement en composantes exhalatives additionnelles (CaO = 5.3 ± 3.9 % poids; P2O5 = 1.43 ± 1.00 % poids), une signature oxydée (Fe/ Mn = 10 ± 6), ainsi qu’une signature d’éléments immobiles communs (Zr/TiO2 = 0.025 ± 0.007) indicative d’une source pélagique. Les roches volcaniques encaissantes calco-alcalines à transitionnelles peuvent êtres reconnues par leur rapport Zr/TiO2, et à un moindre degré par leur rapport Th/Nb: Formation de Nepisiguit Falls: Zr/TiO2 = 0.053 ± 0.004, Th/Nb = 1.08 ± 0.37; Formation de Flat Landing Brook: Zr/TiO2 = 0.107 ± 0.043, Th/Nb = 0.86 ± 0.17. Une répétition symétrique de la séquence stratigraphique Mur-Formation de Fer-Toit a été observée dans le forage DDH-B357, avec des domaines distincts constitués de roches volcaniques felsiques séparés par les trois formations de fer. La meilleure explication est que le flanc ouest de l’anticlinal Brunswick à plongée sud est affecté par des plis parasites F2, similaires aux zones de charnière contenant les sulfures massifs des mines Brunswick No. 6 et No. 12. La géochimie des formations de fer et la chimiostratigraphie des roches volcaniques felsiques en forage peuvent fournir un outil d’exploration minérale efficace dans les roches structuralement complexes du Camp Minier de Bathurst."

Jan 1, 2006

By S. R. McCutcheon, D. R. Lentz, W. S. Downey

"Abstract - The Little Falls member of the Nepisiguit Falls Formation is situated in the northern part of the Brunswick Belt of the Bathurst Mining Camp and has been interpreted as the distal equivalent of proximal tuffaceous rocks that host the stratiform Brunswick No. 12 and No. 6 Pb-Zn massive sulfide deposits. It comprises fine-grained, greenish-gray tuffaceous sandstone in the lower part, and coarse-grained, crystal-rich tuffaceous sandstone in the upper part. Petrographic evidence suggests that these rocks have a turbiditic origin. The Little Falls member is underlain by the Vallée Lourdes member, mainly composed of relatively shallow-water calcareous rocks, and is conformably overlain by Mn-rich sedimentary rocks, mainly red argillites that host the Tetagouche Falls Mn-(Fe) deposit. All these rocks are considered to belong to the Nepisiguit Falls Formation, part of the Ordovician Tetagouche Group. Whole-rock geochemical data from the fine-grained tuffaceous sandstone and coarse-grained tuffaceous sandstone indicate that the two units of the Little Falls member are distinct. Zr and TiO2 contents, and total rare earth element (REE) values are higher in the coarse-grained unit (average Zr/TiO2 = 0.040, average SREE = 247 ppm, n = 6) than in the fine-grained unit (average Zr/TiO2 = 0.048, average SREE = 158 ppm, n = 17), which can be attributed to the variation in crystal content between the two units. Both units are HREE-enriched and have elevated La/Yb relative to the typical Nepisiguit Falls Formation. Overall, the geochemical data combined with evidence from the bounding units suggest that the Little Falls member was deposited in relatively shallow water, possibly in a near-arc environment. The relationship of volcanic facies within the Nepisiguit Falls Formation and the geochemistry of these facies indicate strongly that fine grained, reworked tuffaceous rocks, regardless of whether they are the distal equivalents of proximal tuffaceous rocks, are not associated with the major ore-bearing horizons of the Bathurst Mining Camp. Sommaire - Le Membre de Little Falls de la Formation de Nepisiguit Falls se retrouve dans la partie nord de la Ceinture Brunswick du Camp Minier de Bathurst ou elle a été interprétée comme l’équivalent distal des roches tuffacées proximales hôtes des gisements de sulfures massifs de Pb-Zn stratiformes Brunswick No.12 et No.6. Il consiste en grès tuffacé à grains fins gris verdâtre dans sa partie inférieure et en grès tuffacé à grains grossiers riche en cristaux dans sa partie supérieure. Les données pétrographiques suggèrent que ces roches ont été déposées par des courants de turbidité. Le Membre de Little Falls repose sur le Membre de Vallée Lourdes, lequel consiste principalement en roches calcareuses déposées en eau relativement peu profonde; il est de plus recouvert en concordance par des roches sédimentaires manganifères, lesquelles consistent principalement en argilites rouges hôtes du gisement de Mn-(Fe) de Tetagouche Falls. Toutes ces roches appartiennent à la Formation de Nepisiguit Falls, laquelle fait partie du Groupe de Tetagouche, d’âge Ordovicien. Les données lithogéochimiques des grès tuffacés à grains fins et à grains grossiers indiquent que ces deux unités du Membre de Little Falls sont distinctes. Les teneurs en Zr et en TiO2, ainsi que la teneur totale en Éléments des Terres Rares (ÉTR) sont plus élevées dans l’unité à grains grossiers (Zr/TiO2 moyen = 0.040, SREE moyen = 247 ppm, n = 6) que dans l’unité à grains fins (Zr/TiO2 moyen = 0.048, SREE moyen = 158 ppm, n = 17), ce qui pourrait s’expliquer par la variation de la quantité de cristaux dans chacune de ces deux unités. Chacune de ces deux unités présente un enrichissement en ÉTRL ainsi qu’un rapport La/Yb relativement plus grand que ce qui est typiquement observé dans la Formation de Nepisiguit Falls. Les données géochimiques considérées conjointement à l’information provenant des unités adjacentes suggèrent que le Me"

Jan 1, 2006

By R. P. Kofluk

The nickel-cobalt sulphides produced from limonitic laterite ores by Moa Nickel S.A. in Cuba are refined at the Corefco nickel-cobalt refinery in Canada. Significant economic implications are associated with the refining of precipitated sulphides containing elevated iron contents. The Moa Nickel S.A. operations encompass laterite mining, high pressure acid leaching (H PAL), and ultimately, precipitation of a mixed sulphide product. These processes are reviewed as they pertain to the control of iron and the formation of a mixed sulphide containing nominally 55% Ni, 5% Co and 1% Fe. The contributors to the iron content of the mixed sulphide product are reviewed; the major contributors are the HPAL operation and sulphide precipitation. The precipitation of iron during sulphide precipitation is influenced by the solution acidity, the iron and copper concentrations in the feed solution, and the presence of laterite leach solids. The significance of the copper concentration of the sulphide precipitation solutions is manifested by both physical and chemical modifications of the sulphide precipitates, presumably through the formation of fine copper sulfide seed particles.

Jan 1, 2006

By Raymond D. Potts

"Minntac is a taconite mining, concentrating and pelletizing operation located near the town of Mountain Iron, Minnesota, U.S.A. It is totally owned and operated by USX Corporation and represents its largest source of domestic iron units. Minntac began producing fluxed pellets in 1988 and has produced both acid and fluxed pellets since then. This paper compares the acid and fluxed pellets produced at Minntac. It reviews modifications that have been made to the plant flowsheet and discusses areas recognized for improvement since the beginning of fluxed pellet production. It also comments briefly on the performance of Minntac fluxed pellets in USX blast furnaces and the future of fluxed pellets at Minntac.IntroductionMinntac was built in three steps with each step designed to produce 6 million long tons of acid pellets per year. The actual production has varied though. Figure I shows the production by year at Mirmtac. Step I began production in 1967, Step 2 in 1972 and Step 3 in 1978. Mirmtac produced 16.5 million tons in 1979 but only 3.5 million tons in 1982 when the facility was shut down for six months because of the lack of demand for pellets. Since the initial start up, Mirmtac has produced over 200 million long tons of pellets. Until 1987, all the pellets produced were ""acid"" pellets. In 1987, equipment to produce ""fluxed"" pellets was installed and tested. In 1988, full scale production of fluxed pellets began."

Jan 1, 1991

By L. R. P. de Andrade Lima, D. Hodouin

The paper presents a survey of the possibilities of the simulation techniques for improving the design and operation of gold processing plants. The procedure to construct kinetic models that are used in simulators is first reviewed, and examples are given for cyanide gold dissolution and gold adsorption on carbon. Then, an overview of the structures of the plant simulators is proposed, and the simulation equations formulated for a carbon-in-leach process. Finally, the potential of simulation methods is illustrated by four examples. The first one shows how it is possible to use a simulator to design a cascade of leaching tanks while optimizing an economic performance criterion. The second one illustrates the role of simulators for optimal tuning of the cyanide addition strategy in a leaching circuit. The third example focuses on the power of simulation to design carbon transfer strategies in a carbon-in-pulp process. Finally, the last example shows the role of on-line simulators for optimally supervising the automatic control of cyanide addition into leaching tanks.

Jan 1, 2005

By Haruka Takeura, Tomoaki Murata, Kazunari Yoshida, Masato Adachi

"Pure magnesium is a material with high functionality, however, the cold drawing of this material is very difficult, that is why, until this day there are no optimal cold drawing conditions. Furthermore, cold drawing of pure magnesium wire shows a problem with internal defects that occurs under certain conditions. In this research, the aim is the suppression of internal defects, and final target is to create the optimal cold drawing conditions for pure magnesium wires. The first step is the investigation of the drawing limit by using 250°Cannealed wire. As a result, reduction of 10% per pass was chosen for stable wire drawing. However, in this case, it was found that internal defects occurred at total reduction of over 45% during drawing. Investigation of intermediate annealing conditions that can suppress internal defects, and influence on internal defect that the die half angle and reduction per pass. As a result, it was found that the drawing condition capable of suppressing internal defects most efficiently was 13% reduction drawing by using under 6°half angle die. Consequently, it’s possible to manufacture a cold fine drawn pure magnesium wire of 100µm, without defects in the center of the wire and hindering its mechanical properties.INTRODUCTIONMagnesium is a light and high functionality material that has high vibration absorbency, heat dissipation, electromagnetic wave-shielding and recycling efficiency (Conruy, 1989). However, proper cold wire drawing conditions haven’t been established, that is why warm or hot processing is commonly used (Oishi, Mori, &Kawabe, 2005). As a result, strength improvement of the wires is not possible, that is why the production of medical tools is disregarded. If it was possible to cold draw magnesium wires, the applications for material products would expand. Further, in wire drawing such difficult processing material, if appropriate processing conditions are not selected, defects will be generated inside the drawn wire."

Jan 1, 2017

By J. E. Carter, D. P. Wall

"This paper details the highlights of the open-pit and underground operations of Mclntyre Mines Limited in the Smoky River area of Alberta. Mining methods, operating equipment and manpower are outlined, followed by a discussion of reclamation and environmental control.IntroductionMcintyre Porcupine Mines Limited was incorporated in 1911 and for many decades was known primarily as a gold producer in the Porcupine district of northeastern Ontario. The company, however , has held coal leases in the Smoky River area, near Grande Cache, Alberta, since 1921. Preliminary studies were carried out in the region from 1959 to 1963. In 1964, Mitsubishi, a leading Japanese trading company, (on behalf of Mcintyre), investigated the area as a possible source of coal for the Japanese steel industry. The initial report concluded that Smoky River coal was of high quality, comparable with some of the best metallurgical coals in the world."

Jan 1, 1981

By W A. Bardswich

The numerous factors associated with the prov1s1on of satisfactory air conditions in hot and humid Canadian mines are described. The main heat sources are auto-compression and the actual flow of heat from the rock. Temperatures reach 97°F at a depth of 8,100 feet. Various methods used in coping with high temperatures are described, including the use of ice stopes and heat exchangers. Moisture control, desirable air volumes and velocities, sizes of airways and methods of distribution are important considerations. A comparison of the temperatures, humidities and types of airways of two deep mines should prove useful in the design of future ventilation systems. Introduction OUTDOOR temperatures in northern Ontario vary from a low of around -40°F in winter to a high of about +90°F in summer. The average annual mean temperature over a 12-year period was +35°F, with a summer mean of 54 o and a winter mean of 16°. Because of low outdoor temperatures, a number of northern mines must heat fresh air for underground ventilation in winter; others, with high rock temperatures, are faced with a year-round cooling problem.

Jan 1, 1965

By K. Bachmann, M. Rudolph, U. A. Peuker, H. H. Duong, T. Heinig, T. Leißner, H. Schubert, Helmholtz-Institute Freiberg for Resource Technology, Technische Universität Bergakademie Freiberg

"Minerals can be liberated by random fracture of particles into smaller fragments or by detachment along phase boundaries. These two mechanisms represent borderline cases. When ores get comminuted the liberation of minerals is achieved to some extent by both mechanisms. This article describes a method to determine the extent of transgranular and intergranular fracture on surface exposure of minerals based on 2-dimensional liberation analysis.The approach uses the non-biased surface information like phase specific surface area (PSSA), phase specific free surface (PSFS) and phase specific locked surface (PSLS) of minerals and their change with comminution. The amount of transgranular and intergranular fracture on surface exposure can be calculated using the phase specific surface parameters.A sedimentary rock (apatite ore), an igneous rock (nepheline-syenite) and an artificial material (copper slags) were ground to different fineness. Based on the mineral liberation analysis (MLA) of feed and products, the extent of phase boundary fracture on the surface exposure of the minerals is studied.INTRODUCTIONMinerals can be liberated ether by comminution or by detachment (Gaudin, 1939). Liberation by comminution is a random fracture mechanism, which is not being influenced by ore texture, grain boundaries and mineral features (transgranular fracture). Liberation by detachment represents a fracture along grain boundaries (intergranular fracture). Random fracture often is named as the dominating mechanism for the liberation of ore minerals. This has been the basis to simplify models for liberation modelling (Barbery, 1991; King, 1979; Meloy, 1984) assuming that the probability of cracks moving along grain boundaries is zero. Thus, no interfacial area is lost during comminution."

Jan 1, 2016

Purpose of TSUG Continuous Improvement in Mining Share Best Practises Exchange Ideas Network for Frontline Supervisors and Middle Management Meetings ? Two per Year -Spring and Fall ? Thirty Five to Forty Attendees ? Rotate Between Host Properties ? Host Mine Provides ? Meeting Room for One Day Tour of Mine and Maintenance facilities on Second Day

May 1, 2010

ABSTRACT Based on mineralogical characteristics and processing techniques required, gold ores can be classified into 12 types: gold placers, quartz vein-lode ores, oxidized ores, silver-rich ores, iron oxide copper-gold ores, porphyry copper-gold ores, iron sulphide ores, arsenic sulphide ores, antimony sulphide ores, bismuth sulphide ores, telluride ores, and carbonaceous sulphide ores. The bulk mineralogy and gold deportment of each ore type differs and may have a significant impact on ore processing and metal extraction. This paper summarizes the bulk mineralogy and gold deportment in some major types of gold ore and discusses the potential impact of gold deportment on gold metallurgy.

Jan 1, 2013

By C. Anderson, H. Huang, P. Miranda, E. Dahlgren, I. Chandra, M. Jeffrey

The latter part of the 20th century saw great advances in the treatment of refractory gold ores coupled with increased reliance on the use of cyanide for gold processing. Now, in many parts of the world, there is social pressure to limit or eliminate the use of cyanide. As well, treatment of some refractory ores or concentrates which have excessive cyanide consumption, gold cyanide pregrobbing or significant sulfide content remain difficult. This paper will outline the history of the development of alkaline sulfide leaching as an ancillary process to nitrogen species catalyzed (NSC) pressure leaching. Electrochemical fundamentals and the applicable thermodynamics of the alkaline sulfide hydrometallurgical system will be outlined. As well, examples of refractory gold recovery with alkaline sulfide hydrometallurgy such as an arsenopyrite gold concentrate application, a chalcopyrite gold concentrate application, a pregrobbing gold ore application, and a cyanide consuming gold ore application will be delineated in this paper.

Jan 1, 2005