Search Documents

By A. R. Naji Meidani, A. Cameron, A. Richardson, M. Isac, R. I. L. Guthrie

The supersonic core of shrouded jets remain coherent over longer distances vs conventional supersonic jets. This phenomenon should allow for greater penetration of oxygen into slag/steel reactor systems. As such, they hold the promise for faster slag/metal mixing in BOF type metallurgical reactor systems, possibly creating greater surface area/volume ratios of reacting phases, and thereby faster kinetics, as compared to conventional supersonic jet systems. In order to assess the potential of shrouded supersonic jets versus their conventional counterparts, an experimental investigation of impinging shrouded supersonic jets into a water model of a simplified BOF system was carried out in the MMPC's water modelling laboratory. The experimental results for three different designs of a shrouded supersonic jet nozzle have been compared in terms of greater penetration depths and reduced mixing times. Based on a novel dimensional analysis, the depth of penetration of a gas jet into a liquid bath is shown to depend on the nozzle-bath distance, the liquid's Froude, Reynolds and Weber numbers, reflecting the ratios of gravity, viscous and surface tension forces to the jet's inertial, or momentum, forces. Good agreement between the mathematical model and experiment was obtained in terms of predicted and observed depths of penetration. Further efforts have been made to study jet penetration into liquid metals. The effects of mean liquid density of slag/metal mixtures and a wide range of gas flow rates on the penetration depth were investigated theoretically. The results show that the penetration depth can be increased with increasing gas flow rate and decreased bath density.

Jan 1, 2004

By E. Quaquero

This article reports on the current state of an ongoing research project which is aimed at implementing intelligent models for hardly predictable hazard scenarios identification in construction sites. As past evidences showed that no programmatic action can deal with the unpredictable nature of many risk dynamics, we tried to survey on how the current approach for safety management in the construction industry could be improved. In our previous research the use of Bayesian networks elicited from subjective knowledge were preliminarily tested. Those networks might be meant as a reliable knowledge map about accident dynamics and they showed that a relevant ratio of occurrences fall in ?hardly predictable hazards? class, which cannot be warded off by programmatic safety measures. This paper reports the second outcome of our research project, which focused on the development of first elementary fragments, regarding the occurrence of a possible ?hardly predictable scenario?. Instead of experts? contributions (who, over their carrier, seldom incurred in accidents), we used ?legal cases? as an accurate source of information. They suggested which categories of ?hidden hazard scenarios? are more likely to happen. We found that the most frequent hidden hazard scenarios are linked to operator?s negligence and abnormal behavior, e.g. irregular removal of scaffolding?s components, unprotected openings, improper use of PPE, etc. Every pattern determined by legal cases has been formalized by a fragment (i.e. elementary network) of the overall Bayesian network. Finally, all the elementary networks were integrated into a comprehensive intelligent tool for realtime hardly predictable hazards prevention. The final setup, asked for interfacing these intelligent models to a low-level sensor network and used to feed them with inputs about the current state of the context, is discussed too.

Aug 1, 2013

By A. Paulin, J. Roth, S. Spaic

This experiment was carried out to see whether copper-iron ingots from Late Bronze Age hoards could have been produced by smelting ferruginous copper ores. Since ferruginous copper-ores are chalcopyritic, chalcopyritic concentrate from a present day copper mine was dead roasted in our experiment in lieu of a rich chalcopyritic ore. Charcoal was used as a reducing agent in the reduction of calcine (i.e., a product of dead-roasting), and quartz sand was used as a flux. Two separate metallic solutions, a copper-base and an iron-base alloy, were obtained as a result of two factors: the presence of carbon and the miscibility gap in the Cu-Fe-C system. The metallic melts appeared in a form of bigger or smaller droplets, enclosed by a molten slag which, during the cooling, solidified into metallic beads. The presence of both metals was noticed in the majority of the examined beads. It was therefore concluded that calcine consisted of an intimate mixture of oxides of both metals which were simultaneously reduced during the reduction process. Due to the miscibility gap in the Cu-Fe-C system, separate iron and copper regions were formed in the beads. In both regions, sulphide inclusions were found. The formed molten copper and molten iron solution were found to be saturated solutions. The metallographic analysis revealed the precipitation of iron out of copper and that of copper out of iron during the cooling and solidification of melts. The formed slag contained little iron and no copper oxide.

Jan 1, 2001

By R. Khanna, I. Mansuri, S. Devasahayam

"Recycling polymer based end-of-life materials as carbon resources for a partial replacement of coke/coal can make important contributions towards enhancing the environmental sustainability of steelmaking processes. An in-depth high temperature (1550°C) investigation has been carried on waste CDs/DVDs focussed specifically on char generation, characterization and dissolution into molten iron. The simultaneous presence of carbon and oxygen in polymeric chains on polycarbonate substrates resulted in the generation of a significant pore structure and exposed surfaces. Carbon dissolution studies into molten iron were carried out on the raw polymer as well on chars; high levels of carbon pick-up were observed in both cases after 15 minutes of contact at high temperatures. INTRODUCTIONOver the past sixty years, plastics have played an important part of our daily lives and are being increasingly used in all aspects of the global economy. More than 260 million tons of plastics are produced annually worldwide. Their rapid growth and extensive utilization with a short life span (such as packaging) has created a massive waste problem. Although the waste plastic component in municipal solid waste (MSW) amounts to only about 10 %, plastics have a high volume-to-weight ratio and these are generally not biodegradable. In Australia, ~19.20 % of plastics were recycled in 2009-2010 (PACIA, 2010); with the total consumption being estimated at 1,501,258 tonnes, 288,194 tonnes of plastics were recycled. There are serious environmental concerns with the two key waste management options, i.e. land filling and incineration, and there exists an urgent need for developing alternative recycling approaches. In this paper, we focus our attention on recycling waste CDs/DVDs polycarbonate substrates as a carbon resource in steelmaking.CDs/DVDs used for music/data/image are made from aromatic polycarbonate resin (hereafter abbreviated PC). This resin is also widely used as an engineering plastic in applications such as automobiles, mobile phones, notebook type personal computers, cameras & video cameras, electric & electronic appliances, fire equipment, life & living goods, roofing sheets, etc. High consumption and growth (~10% annually) of PC utilization is attributed to its excellent properties such as outstanding impact resistance, transparency, heat resistance, and dimensional stability. The molecular formula and composition of PC resin is given below:"

Jan 1, 2012

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber plant was recently completed at an existing facility, in order to treat the sulphur dioxide off-gas emitted from rotary kilns. Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong operational readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.INTRODUCTIONCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Quebec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary byproductof the process.Fresh hydrated lime and CDS residue is captured by the dust collection system and is re-circulated to the CDS via a fluidised transport system. Clean off-gas passes through the dust-collection system and is then sent to the atmosphere by a single exhaust fan.The CDS residue purged from the system is combined with the dust collected from the kiln offgas system and this mixture is wetted in the already exiting agglomeration system, to minimize dust generation during handling, and then sent to disposal."

Jan 1, 2016

By P. -A. Bosse, J. Robitaille, P. Blatter

The LaRonde ore is a Cu-Zn-Pb ore with gold (3-4 g/t) and silver (60-100 g/t). The precious metals are recovered with copper concentrate, zinc concentrate and cyanidation of zinc tails via Merrill Crowe precipitation. Subsequent to a recent mill expansion, excessive gold was reporting to zinc concentrate with a concurrent decrease in gold to copper concentrate. Owing to the higher return obtained from the metal, the mill endeavors to recover additional gold and silver to the copper concentrate and minimize the placement of precious metals to the zinc concentrate. A gold deportment study showed that the gold occurs mainly as küstelite, with a moderate amount of electrum and a minor amount of native gold. It also showed that various sulfur-based Au-and/or Ag-bearing coatings on liberated küstelite and electrum were the major mineralogical factors that caused gold and silver to report to zinc concentrate. By frequency, such coatings were observed on 70-80% of total liberated gold particles reporting to the zinc concentrate. Based on the gold deportment and the chemistry of the coatings, the collector chemistry was reviewed and a new collector was added into the circuit which resulted in a significant increase in gold and silver recovery to the copper concentrate. The information obtained from the mineralogy confirmed and guided other process optimization. In this paper, the authors will describe the process mineralogy of the LaRonde ores, and in particular, the mineralogical evidence diagnosing the problem. Reference will also be made to the rationale behind how the problem was solved, the results achieved, and future steps in optimization.

Jan 1, 2005

By Yoginder P. Chugh

This paper discusses an ongoing field study in southern Illinois (USA) that focuses on: 1) Identifying mechanisms of instability in the set-up rooms (SR) and their T-junctions with headgate and tailgate entries, 2) Developing alternate 3-entry and 4-entry set-up rooms geometry using 3-D numerical analyses, 3) Implementing developed geometries in cooperation with mining professionals and regulatory agencies, and 4) Demonstrating performance of implemented geometries through field monitoring. Illinois longwall mining operations typically experience ground control problems (roof falls, rib sloughing, floor heave, etc.) within SR layouts and around the T-junctions of SR. These occur around the areas where the SR for adjacent longwall face (to be mined) connect with the SR of the previously mined face, and around the tail-gate entries of the mined-out longwall face and around the T-junctions of SR. The problems manifest as highly fractured immediate roof strata, major shear zones in the roof, horizontal displacements within the excavations that result in shearing off the heads of the bolts, floor heave and severe rib sloughing. Similar observations have also been made in longwall mining in Utah.

Aug 1, 2013

By J. K. Szymanski

"RÉSUMÉPour maintenir de bonnes performances technique et économique dans l’exploitation par chambres vides (open stope) il est primordial d’assurer un contrôle efficace des limites réelles des chantiers d’abattage. C’est pour cette raison que, de plus en plus souvent, les opérateurs miniers utilisent un dispositif de laser (Cavity Monitoring System: CMS) qui permet de mesurer les dimensions réelles de chantiers en vue de calculer principalement la dilution et les pertes du minerai ainsi que d’autres paramètres. Malheureusement, il n’existe présentement aucune méthodologie commune, qui permettrait d’interpréter ces résultats selon les mêmes critères pour faciliter d’évaluations juste et précise de la réalisation par rapport à la planification en vue d’en apporter de corrections, dans les différentes opérations minières, si nécessaire. Dans la première partie du présent article on discute les principales séquences d’exploitation utilisées dans l’extraction par chambres vides. Par la suite, à l’aide des sections transversales et longitudinales on illustre toutes les phases des travaux miniers. Ceci en vue de permettre au lecteur de comprendre mieux c’est qui peut se passer effectivement dans les chantiers d’abattage. Par après on donne les définitions générales de principaux facteurs de performance technique. Finalement, l’exemple numérique, élaboré à partir des résultats de l’arpentage au laser effectué par la mine Bousquet 2 dans un chantier d’abattage, donne les détails concernant les définitions ainsi que les valeurs de nombreux facteurs de performance technique, qui pourraient être utilisés, par après, par les opérateurs miniers dans le suivi de leurs exploitations souterraines."

Jan 1, 1997

By A. Azizi, P. Blatter, A. Bouajila

ABSTRACT In-situ monitoring of gold dissolution by means of a rotating electrochemical quartzcrystal microbalance unveiled dramatic decreases in gold leaching from sulphide-rich ore after 360 minutes in an actual cyanidation circuit. Pre-oxidation was effective in enhancing gold extraction by preventing a passive film from forming on gold surfaces. This work aims to highlight efforts undertaken to determine (1) how gold cyanidation is limited by passivation, (2) what reactions and mechanisms are involved during sulphide-rich ore cyanidation, and (3) how peroxidation efficiency of an industrial sulphide ore is controlled by galvanic associations between its sulphide constituents.

Jan 1, 2013

By Henri-Louis Jacob

Le secteur des substances non-metalliques repose au Quebec sur !'exploitation et la transformation d'une dizaine de mineraux ainsi que sur la production de materiaux de base destines surtout a l'industrie de la construction. L'ensemble de cette production representait en 1982 une valeur estimee a plus de 797 millions $, soit tout pres de 400Jo de la production minerale du Quebec. L'amiante et Jes scories de titane destines a la production de pigments, qui comptent parmi Jes plus importantes substances minerales produites au Quebec, representent respectivement 370Jo et I 70Jo de la valeur totale des non-metalliques tandis que le groupe des materiaux de construction represente pres de 400Jo. Les autres substances, parmi lesquelles ressortent nettement la tourbe, la silice et la magnesite, representent une valeur totale de 61.5 millions $.

Jan 1, 1984

By C. Riveros, H. Henein

Bulk Metallic Glasses have a high potential as advanced engineering materials due to their various properties including strength and corrosion resistance, to name a few. This paper investigates amorphous phase formation and rapid solidification characteristics of impulse atomized Co-based alloys in order to understand and control the application properties of the final products. Amorphous fraction and kinetic crystallization properties of the atomized Co-based alloy powders were quantified by means of Differential Scanning Calorimetry. In addition, different but complementary characterization tools were used to analyze microstructures of the powders. These include optical microscopy, X-ray diffraction and micro-hardness tests. While the amorphous fraction within the powders is promoted by high cooling rate and smaller powder size as expected, hardness is found to decrease with the fraction of amorphous phase.

Jan 1, 2015

By M. Lindgren, M. Latva-Kokko

Process performance can be significantly influenced by proper design of hydrometallurgical reactors. Optimal reactor configuration is case specific and depends on process requirements such as reaction rate limiting factor and particle size distribution. Choice of materials and manufacturing methods also play important roles in highly corrosive and abrasive environment often involved in hydrometallurgical industry. In this paper performance of different reactor designs has been compared in some typical hydrometallurgical applications. Results show that significant improvement in energy consumption, gas utilization efficiency and equipment lifetime can be achieved with process specific reactor design.

Jan 1, 2014

Diverse and considerable energies are associated with mobile equipment operated and maintained on mine sites. Loss of control of these energies is a common cause of injury on mine sites and this is well recognised by the mining industry. In 2006, 4 multi-national mining companies formed the Earth Moving Equipment Safety Round Table (EMERST), with the aim of engaging collectively with the manufacturers of equipment to accelerate improvements in mining equipment design. Originally focused on surface mining equipment, and particularly haul trucks, the focus of EMESRT widened to include underground and exploration equipment. Since 2006, EMESRT has maintained a program of regular visits and other engagements with a steadily increasing number of manufacturers. The membership of EMESRT has also increased, with 15 companies being members in 2012. An initial step undertaken by the EMESRT members was the development of ?Design Philosophies? which drew of the collective experience of mining companies to identify potential unwanted events which cause equipment related injuries and illness. A technique for analysing risks associated with operation and maintenance tasks, the Operability and Maintainability Analysis Technique (OMAT), was subsequently developed and trialled. In 2011, the EMERST members resolved to propose a common form of safe design information to be requested by all members companies during procurement, and the resulting EMERST Design Evaluation for Equipment Procurement (EDEEP) process was launched at MINExpo in Las Vegas in September 2012. The outcomes of OMAT risk assessment and control activities are integrated during this process into a common ?Safe Design Information? template for communication to prospective purchasers. The aims of requesting manufacturers to follow this process are to provide equipment purchasers with a common way of assessing how well the issues in the EMESRT Design Philosophies are addressed in the equipment design; and to provide manufacturers with additional information for use during equipment design. The process involves identifying priority tasks based on frequency and the severity of the consequences of potential unwanted events identified in the EMESRT Design Philosophies; undertaking a task-based risk assessment of priority tasks in conjunction with site-based personnel; evaluating the effectiveness of control measures; and providing information about safe design features in a standardised format.

Aug 1, 2013

By P. Mengé

The covering of a hydraulically filled goethite pond is discussed from a geotechnical point of view. The characteristics of the goethite were defined in order to allow a detailed study of the procedure for the construction of the cover on top of the soft material and a verification of the stability of the cover and side slopes after construction. These characteristics and the main results of the studies are given, as well as the experiences and observations made during the execution of the work. Finally, the monitoring plan, during and after construction, is also discussed and some results are given. The 'Design and Construct' contract form was used to allow the contractor to choose the optimum and most economical method to realize the closing of the pond, based on his experience with similar projects. The works were carried out between mid 2003 and the end of 2004. The paper will, amongst others, discuss the special method of working that had to be developed to allow the covering of the whole pond in a relatively short time period, without soil improvement methods such as vertical drains or stabilization by in situ treatment. Fill material was used to establish a platform on top of the soft material so that the cover liner and finishing layer could be installed on top of the fill layer. The 'floating roof' principle was used; subsidences were allowed to occur during the installation of the impermeable top liner and soil cover.

Jan 1, 2006

By N. J. Duncan

"Coal mining, whether surface or underground, has hazards that make it unique in the field of industrial safety and health. The often soft, faulted and folded sedimentary strata make wall or roof movement a risk to the safe and economic removal of the coal, while the extraction and handling of coal may create an explosion hazard even in surface operations, In Canada, these problems are compounded by the situation of the coal fields which range from deep undersea deposits in Nova Scotia to steeply pitching thick coal seams high in the Rocky Mountains. Climate too can create its own problems, particularly the effect of metals of minus 40°C temperatures, as crumpled dragline booms at prairie strip mines witness. Because of the difficult and sometimes hazardous conditions, Canada's underground colliery managers, in common with those of other Commonwealth coal-producing countries, must have a government ""certificate of competency"" before being appointed as mine managers. Certification of assistant managers (""under-managers"") and foremen (""fire-bosses"") is also a legal requirement for all of Canada's underground collieries, while the province of Alberta requires certification of surface management personnel. Electricians and mechanics who install and maintain the specially designed equipment underground and in hazardous areas of surface mines and processing plants, and mine surveyors who ensure accuracy of the location of underground workings, must also hold government certificates of competency. The requisites for all certification include a minimum work experience and knowledge of coal mining technology and mine safety and health legislation. Despite recognition of the hazards and increasing knowledge of methods of preventing explosions of flammable gas and coal dust in Canada's underground mines, there have been several disastrous explosions such as those at Springhill Colliery in Nova Scotia in 1891 with the loss of 125 lives, at Hillcrest Colliery in Alberta in 1914 with 189 dead, and more recently · explosions and fires in No. 20 and No. 26 Collieries in Cape Breton. Preventing explosions has required developing optimal ventilation techniques, reducing ignition potential, suppressing ignition at source, draining flammable gas before it can enter the air courses, and preventing, or sealing off, autogenous heatings with their associated carbon monoxide or explosion dangers."

Jan 1, 1985

By P. Curry, H. G. Stephenson, B. Van Den Bussche

"Three Sisters Resorts Inc. currently owns a2035 acre (824 ha) parcel of land, which previously belonged to Canmore Mines Ltd. Approximately 50% of these lands, that are slated for residential, resort and recreation development, have been undermined for coal in one or more seams.Norwest Mine Services has been contracted by the developer to assess and advise them on any past mining activity that may be potentially hazardous to their development and offer solutions to how these hazards may be mitigated or avoided.The following paper deals mainly with the procedures put in place and accepted by the approval authorities, and the Staged approach to the Investigative Procedure that Norwest follows in the mining assessment and mitigation work for Three Sisters."

Jan 1, 1996

By T. Hidayat, D. Shishin, V. Prostakova, M. Shevchenko

The chemical compositions of copper feed streams are becoming increasingly complex following the growing demand for metals and corresponding shortages of primary sources. The optimisation of process conditions requires an accurate description of phase equilibria and thermodynamics. Integrated experimental and thermodynamic modelling research program on the characterisation of the complex, multi-component, multi-phase gas-slag-matte-speiss-metal-solids Cu2O-PbO-ZnO-Al2O3- CaO-MgO-FeO-Fe2O3-SiO2-S-(As-Bi-Ni-Sb-Sn-Ag-Au) system is being carried out to support companies undertaking the pyrometallurgical primary production and recycling of copper. The experiments involve high temperature equilibration in controlled gas atmospheres, rapid quenching and direct measurement of equilibrium phase compositions with quantitative microanalytical techniques, including electron probe X- ray microanalysis and Laser Ablation ICP-MS. The thermodynamic modelling is undertaken using FactSage computer package with advanced thermodynamic solution models. The continuing development of research methodologies has resulted in significant advances in research outcomes. Implementation of the results of these fundamental studies involves an ongoing collaboration of researchers and industry technologists. An overview of recent progress in research, implementation and applications in industrial practice are given in the paper. INTRODUCTION Rapidly developing technologies increase the demand for various metals in number and volumes. Modern technological devices such as mobile phones, computers, other electronic devices, have dozens of metals—all those metals have to be a) produced and b) recycled. The fast transition in mobility from fossil energy delivered through combustion to renewable energy first stored in bakeries and delivered through electric engines introduce a significant change in the metal demand in terms of both type and volume of metals. Pyrometallurgy is playing a key role in supporting these changes in our industrialised society.

Jan 1, 2019

By Tadeusz W. Wlodek

THE known phenomenon that a test-piece of ferro-magnetic steel is magnetic after it has been broken in tension indicates that, while it is being loaded, the steel acquires magnetic properties. In the present investigation of the influence of the stress on the magnetic flux, repeated pulsating stresses of increasing amplitude, varying from zero to the maximum tensile value, i.e., pull-pull loading, were employed. The specimens were prepared from two types of carbon steel and two of alloy steel. The magnitude of the magnetic flux was determined indirectly. The voltage and mode of variation of the electromotive force induced in a coil surrounding the stressed steel specimen were measured as an indication of the varying magnetic flux within the specimen. Curves representing the electromotive force induced by the varying magnetic flux show that as the tensile load increased so also the magnetic flux increased, with a corresponding increase in measured e.m.f. At a certain stress there is a sharp bend in the voltage curve (point Win the diagram, Figure 5); this critical stress corresponds very closely with the yield stress (0.2 per cent permanent strain). Beyond this point, slight increases in the stress produce large increases in the voltage. The wave form of the e.m.f. was registered on an oscillograph. Analysis of the curves so obtained demonstrated the necessity of continuing these experiments, in order to determine the type of induced wave form associated with various types and amplitudes of stresses. In these experiments, the shape of the stress wave was sinusoidal, although the shape of the induced e.m.f. was sinusoidal only up to a certain load and became more and more complex above this load.

Jan 1, 1944

By E. L. Warburton

Before entering into a discussion of wet washing, it will be advisable to consider the various phases and conditions sur- rounding the problem of cleaning coal from the Corbin mines. Corbin is located in the south-east part of British Columbia in the Crowsnest Pass district, about 35 miles north of the International boundary and about three miles west of the Flat-head Range of the Rocky Mountains. It is reached by a rail-way, about thirteen miles long, from McGillivray, B.C., a point on the Crowsnest branch of the Canadian Pacific rail-way, owned and operated by the Eastern British Columbia Railway Company, a subsidiary company of Corbin Coals, Limited. The coal is assumed to occur here, as principally elsewhere in the Rockies, in the Kootenai series of the Lower Cretaceous, but owing to the disturbed condition of the surrounding country and, therefore, the magnitude of the geological study involved, this has never been definitely worked out. The coal is of the usual Crowsnest high-grade steam-coal, containing from 9 to 12 per cent. of ash, but appears to have 4 to 5 per cent. less volatile combustible matter than other coals being mined in this district, a representative analysis being about as follows:

Jan 1, 1924

By E. Nolasco, J. Ouellet, T. Tikka

"Shaft bottom structural systems are used in underground mining to support transfer of personnel, equipment and ore to and from underground to the surface. This paper first summarizes the evolution of design philosophy from a concrete tower supported on a concrete plug to the current structural steel design arrangement with unlined shaft walls, clear shaft bottom area with only a concrete housekeeping pad. Then the paper reviews the design parameters, analysis and design, and construction methodology for this rather unique shaft bottom structural system consisting of three sets of hitch beams, with each having specific functional requirements. INTRODUCTION Shaft bottom structural systems are used throughout the world in underground mining operations to provide a means to support the transfer of personnel, equipment, materials, ore and waste entering and exiting a vertical shaft ready for transport to and from the surface via the hoisting system. The shaft bottom structural system, for the Service Shaft (SS) at the Jansen Mine, is designed to accommodate two skips, a personnel/equipment cage, counterweight, services, loading pocket, rope changing, arrestor system, crash (or catch) beams, access platforms, stairs and rope divider system. Stantec and BHP have engineered a unique structural steel shaft bottom system for hoisting system at a Potash Mine. The shaft bottom structural system connects to a fixed guide and cantilever bunton system, used in the vertical shaft (shaft barrel), above the shaft bottom. The geometry for the shaft bottom structural system, shown in Figure 1 a), features three sets of hitch beams, beams which span across the shaft excavation or barrel. At the top of the structural system are two upper hitch beams. These hitch beams support a 64 metre suspended rectangular braced tower (upper tower), complete with steel guides for the conveyances. The upper tower passes through the main station (potash or mining) level and then connects to the top of the arrestor (lower) tower structure via a sliding vertical connection. The potash level is supported by two hitch beams spanning the shaft and loading pocket excavations. The arrestor tower, a braced compression tower structure, is carried by a third set of hitch beams. Below the third set of hitch beams is a short suspended tower complete with access platforms, stairs and the rope divider system."

Jan 1, 2019