Search Documents

By Keith Haddock

"The Sheerness Mine, a new surface coal mine located near Hanna, Alberta, went into full production in mid-1995. The mine, which is operated by Luscar’s subsidiary Forestburg Collieries (1984) Ltd., has the design capacity to supply up to 2.1 million tonnes of sub-bituminous coal per year to the adjacent Sheerness Generating station under a 30-year contract. This paper documents the construction phase of this project and highlights the major equipment purchases as well as the construction of the mine facilities. The paper also focuses on some of the areas where cost savings have been achieved that have allowed the mine to come on stream six months ahead of schedule, and under budget. Project ReviewMine DescriptionThe Sheerness Mine is located 25 km southeast of the town of Hanna in southeastern Alberta (Fig. 1). The mining property occupies the western portion of the Sheerness CoalField and borders the Montgomery Mine, operated by Manalta Coal Ltd. in the east, and Highway 36 in the west. The Montgomery Mine and the Sheerness Mine exclusively supply the total coal requirement of the adjacent Sheerness Generating Station. The station is owned jointly by Alberta Power Limited (APL) and TransAlta Utilities Corporation (TAU). APL is the operator. Manalta’s Montgomery Mine has supplied coal to the Sheerness Station since its opening in 1986. Coal is shipped by truck from the mines over a network of haul roads to the coal receiving hoppers located on the east side of Highway 36."

Jan 1, 1997

By Mark W. Booth

THE Dominion Steel and Coal Corporation, as a coal mining concern and as a steel industry, has much pumping to do, and the conditions are as varied as it is possible to make them. We are faced with handling large quantities of water at low heads, and small quantities of water at high heads. We have fresh water, we have salt water, and we have highly acidulous water (see Table II). Our pumping problems are concerned chiefly with mechanical reliability, continuous, reliable operation, first cost, and operating cost. The Corporation is actually expending more than 15 per cent of its power consumption at the mines in pumping water, and at the steel plant about 17 per cent; that is to say, 16 per cent of the Corporation's entire power consumption goes into pumping water ( see Table I). We are pumping out of the mines 2 ½ tons of water for every tan of coal that is produced. At the Steel Plant, we are pumping 188 tans of water for every ton of steel we produce. (See Tables III and IV). The mine is pumping at high heads, up to as high as 1,400 feet in one lift ; in the Steel Plant it is, fortunately, at lower heads, 250 feet or 110 lb. being the general maximum. It behooves us, therefore, to look into the question of efficiency. In whatever direction we can gain something, it will be worth while. The centrifugal pump is not an adaptable machine. That is, a pump designed for some particular location and purpose will not always work efficiently if installed in some other place and used for some other purpose. It must generally be designed for the particular job it has to do. Reciprocating pumps are not so sensitive. We have Cameron plunger pumps that can be set up almost anywhere in a mine and they will work, but for big jobs they are apt to be clumsy and the driving power becomes a factor- which is, in fact, the controlling factor in deciding the type of pump we use. One disadvantage of the a.c. induction motor, however, is that its speed cannot easily be controlled. At its rated speed and output, it is a highly efficient machine, but, with any change in these, its efficiency goes all to pieces.

Jan 1, 1944

By J. Laganiere

A considerable part of the sulphuric acid requirements of the Aluminum Company of Canada's Arvida smelter comes from the burning of 180-200 tons per day of zinc '"'sulphide concentrates in a 22-ft.-diam-eter fluidized bed roaster. The plant and its operation were fully de-scribed in a publication that appeared about ten year ago (1). A simplified flowsheet of the roasting and gas-cleaning sections of the plant is given in Figure 1. The wet zinc sulphide concentrates are un-loaded into a pug mixer, by means of a Pay loader, and mixed with water in a mixing tank to make a slurry of 80 per cent solids. The slurry is transferred to a .feed tank and then introduced into the roaster at a point four feet above the constriction plate, which is the height of the settled bed of zinc calcines. The roasting temperature is con-

Jan 1, 1963

By James J. Holmes

ACCIDENT prevention as we know and understand it today is of comparatively recent origin. As a matter of fact, the Industrial Accident Prevention Association of Ontario, which is the oldest organization of its kind in the Dominion, celebrated its thirtieth anniversary only this year. On the other hand, one could say that the history of accident prevention is almost the history of mankind itself. In a general sense, every forward step that man has made throughout the centuries has been largely due to two things: (1) a desire for increased comfort, and (2) the need for safety; and, always, the need for safety has taken precedence over the desire for comfort. While it is true that hundreds of volumes have been published, dealing with the many aspects of accident prevention work, you cannot go to a library and pick out a book that has all the answers in it. Such a book has never been published-we are still looking for some of the answers. However, a good deal of real progress has been made.

Jan 1, 1945

By E. S. Malloch

THE Great War forced the peoples of the world to recognize the importance of the wise development and use of the world's natural resources. Not the least, and perhaps the most, important, is the world's fuel supply- solid, liquid, and gaseous. Without fuel our civilization would be impossible, and mankind would of necessity have to congregate in the torrid zones of the earth's surface for at least six months of every year. Of the three classes of fuels the solid ones are the most plentiful, as well as being the most widely distributed, since few countries are entirely devoid of solid fuels of one kind or another. Until a hundred years ago wood was the fuel most generally used in this country, but since then coal has supplanted wood as a fuel in all its uses, except in the outlying districts and among the farming communities. For many years the supply of coal was thought to be unlimited, but as years went by more thought and study were given to the world's coal resources, until today not only are the limits known, but in one instance at least their depletion is predicted to be almost within the age of living men, unless more provident methods are put into practice for their winning and utilization.

Jan 1, 1928

By M. H. Pettibone

Sohio Petroleum Company's new L-Bar uranium mill near Grants, New Mexico. refines 2722 kilograms of yellowcake daily from 1360 metric tons of ore produced at Sohio 's J.J. No. 1 mine and other nearby mines. This paper follows the ore from the mine through the various processing steps - semi-autogenous grinding, acid leaching , countercurrent decantation, solvent extraction , ammonium diuranate precipitation, washing and drying, and tailings disposal.

Jan 1, 1978

By N. Musee, N. Kornelius

This study presents a neural network approach to modelling the liberation of gold bearing ores. A complete mineralogical analysis of unmilled and milled ores, including gold deportment and gangue content are used as inputs to a self-organising neural net which generates order preserving topological maps. The arrangement and shapes of these clusters are coupled to unmilled free gold data to predict gold liberation in milled ores (absolute error: 4.2%). Moreover, the self-organising maps were diagnostic of the quality of data used, indicating that the relationship between particle size and gangue material content requires further investigation.

Jan 1, 2005

By D. R. Boyle

"The basal type uranium deposits in south central British Columbia occur within unconsolidated, late Miocene fluvial paleochannel sediments that overlie major fault zones within the Okanagan Highlands Intrusive Complex. Prior to the formation of mineralization, paleovalleys containing host sediments were flooded by Pliocene valley basalts of the Plateau Basalt Formation. Five uranium deposits have been outlined to date, of which the Blizzard (4020 tonnes U) and TYee (650 tonnes U) are the largest. The basement intrusive complex underlying the deposits varies in age from early Cretaceous to Eocene and is comprised of quartz monzonite, granodiorite, Coryell monzonite, porphyritic granite and pegmatite.The mineralized host sediments comprise a complex sequence of interfingering conglomerates, arkosic sandstones and mudstones. Organic material is abundant in many, but not all, mineralized beds. Uranium mineralization is present in the form of uranous (ningyoite) or uranyl (saleeite, autunite) phosphates coating clastic grains and filling voids. Because of very strong reducing conditions related to large concentrations of marcasite and organic material, ningyoite is the only uranium mineral in the Tyee deposit, whereas the Blizzard deposit contains a more complex assemblage of minerals (saleeite, autunite, ningyoite). The observed paragenetic sequence of mineral precipitation in the Blizzard deposit (autunite-saleeite-ningyoite) indicates that the uranyl minerals, saleeite and autunite, are primary. Small amounts of Zn, Ni, Co and Mo have been introduced into the Blizzard deposit whereas Mo is the only non ore-forming element enriched in the Tyee deposit. Mn is the only depleted element in both deposits."

Jan 1, 1986

By Ian M. F. Arnold

"Occupational health programs and their role in improving the quality of working life in the mining industry are discussed. Attention is directed to some problems peculiar to the Canadian mining industry. Factors affecting program development are reviewed, as well as parameters affecting cost-benefit analyses.IntroductionThe quality of working life in the mining industry is a more important consideration than in many other industrial environments because of the very nature of the undertaking. It was a strange paradox of the 1960s that preventive maintenance programs for machinery and equipment were well accepted, whereas the concept of ""preventive people medicine"" was basically ignored. Fortunately, there seems to be a swing toward the development of occupational health programs in many sectors of the business community; however, there is a noticeable lack of consistency and uniformity for thought among the members of the mining industry. The blame for this lack o f progress in the occupational field cannot be entirely attributed to the industry, but must also rest with (for the most part) apathetic and inadequately trained physicians. This latter problem is slowly improving with the growing recognition that a well-planned and executed occupational health program may improve the quality of working life for mining employees and their families.There are a number of factors which relate to occupational health in mining, and its effect on working life quality. Included among these are:1. Community isolation.2. High accident risks.3. Occupational disease risks.4. Production demands and the state of the economy.5. Government regulatory requirements.6. Travel demands.These, and others, reflect on all levels of the mining industry. To examine how these factors can be moderated by an occupational health program, it is necessary to first review the rationale for such a program and some of the costs related to it."

Jan 1, 1983

By W. E. Roscoe

"Mineral exploration properties are those on which an economically viable mineral deposit has not yet been discovered. Such properties are bought, sold, optioned and joint ventured on the basis of their perceived potential for the existence and discovery of a viable mineral deposit. The intrinsic value of an exploration property is therefore based on the exploration potential. One measure of the exploration potential is the amount that can be justified to spend on exploration for a viable deposit.The appraised value method uses a cost approach to value exploration properties. It is based on the premise that an exploration property is worth the meaningful past exploration expenditures plus warranted future costs to test remaining exploration potential. Results of past exploration work are analyzed in order to retain only those past expenditures that are productive in terms of identifying remaining potential. Warranted future costs comprise a reasonable exploration budget to test that potential."

Jan 1, 2002

By Emilie Williams

Introduction Mouska Mine, Doyon Division site Background and timeline Obstacles to standard paste delivery system Components of Mouska paste system Technical considerations Operational considerations Mouska Mine Underground gold mine 30 km east of Rouyn-Noranda, Quebec Part of Doyon Division, 100% owned by IAMGold Commercial production since 1991 Cumulative production over 850,000 oz Conventional mining until 2009 485 m shaft from surface 560 m internal shaft 500 tpd (ore and waste) Off-site milling Approximately 150 employees

Oct 1, 2010

By N. T. Avard

THE profitable disposal and utilization of much of our slack coal, lignite, and other low-grade fuels is one of the major problems facing the coal mining industry of Canada today. It is my belief that the pulverization process applied to these fuels opens the door to greater efficiency and greater prosperity, and I wish to discuss briefly with you some features of its development and advantages to date. Indeed, the art of burning pulverized coal under stationary boilers is one of the romances of modern engineering. As a Nova Scotian, I feel some pride in the fact that at Chignecto Mines, N.S., was built in 1906 the first pit-mouth power plant on the North American continent. This was built to make effective for the first time Edison's dream of carrying coal for power by wire rather than by rail. This plant, built by the Maritime Coal, Railway and Power Company, Limited, success-fully utilized underfeed stokers for twenty years but in 1927 was replaced by a more modern plant equipped with machinery for burning pulverized coal, which is now operating very successfully. A further source of pride is the fact that the first boilers on this continent to be operated by pulverized coal were installed by the Dominion Coal Company at New Waterford, N.S., in 1912 and were satisfactorily operated during the lifetime of the plant. It is an acknowledged fact that average living conditions on a large part of the North American continent are far superior to those of any other people on earth. The reason is that we use so much more machinery per capita, and cheap power supply has been a large factor in bringing that about. Statistics show that where one horse-power was used one hundred years ago to assist man in his work, five hundred horse-power is used today. Truly a remarkable development and the key to our present high standard of living. Lack of coal in the chief industrial centres of Canada has forced the extra-ordinary development of the water powers which Providence has placed in those centres. How many of us realize that Canada stands second in the world in the per capita development of hydro power, Switzerland being first and the United States sixth? From this condition, we are reminded of the fact that the per capita foreign trade of Canada far exceeds that of our great neighbour to the South-but another illustration of the benefits accruing from our great power development.

Jan 1, 1937

By E. A. Sobering

Hydraulic filling or sand filling is a system used to fill underground excavations with a dense pulp. Milltailings are commonly used. The resultant fill, after being placed and de-watered, is known as hydraulic fill. These fills have been effectively used to (a) provide immediate support of the workings place during stoping; (b) .facilitate the recovery of pillars; (c) limit surface damage by subsidence; (d) permit the mining of parallel hanging-wall orebodies; (e) stabilize the ground in mines, thereby reducing the rock burst hazard; (f) control and prevent mine fires; and (g) solve tailings disposal .problems. The various uses of hydraulic filling have been developed during the last ninety years. In 1864 it was employed only to control surface subsidence. Since then, this system has been successfully applied to meet specific ground support problems. Methods of handling mine-fill derived from a source outside the stope include transportation ?Of the material by hand, mechanical, pneumatic, and hydraulic means, or a combination of these methods. The hydraulic method has many advantages not found in the others; a significant advantage is the low compressibility of the material when compared to other mine-fill material. The hydraulic filling operation includes the .preparation and transportation of the pulp. The underground practices in .placing the fill vary from mine to mine. The chief reason, formerly, for using hydraulic fill was the exceptional support it provided, but recently it has proven an important means of reducing mining costs. This is especially true where labour is a large part of an alternative method, or where timber consumption is greatly reduced. The indirect benefits of hydraulic filling are probably as important as the direct benefits, and few important disadvantages exist.

Jan 1, 1956

By J. R. Goode

ABSTRACT Aurora Energy Ltd. is considering a 10,000 t/d process plant to produce 97 million lb (43,998,460 kg) of U3O8 over a 17-year project from uranium deposits in coastal Labrador. This paper summarizes the test work, mostly done by SGS Mineral Services in Lakefield, Ontario, and the economic studies supporting flowsheet selection. The proposed flowsheet includes semi-autogenous grinding (SAG) and ball milling, acid leaching using air/SO2 as an oxidant, and resin-in-pulp (RIP) extraction of uranium from the leached slurry. Other unit operations examined include ore sorting, heap leaching, liquid- solid separation, solvent extraction, and nanofiltration for eluate upgrading. We also review the extensive environmental test work and studies that were completed.

Jan 1, 2012

By R. Viljoen, K. Manns

"The mining industry instinctively follows rule-of-thumb design velocities often based on very simplistic theoretical “economic velocity” optimization calculations to determine airway sizes. Although these are important building blocks in ventilation planning it should be recognized that mines are far more complex and various, often opposing factors, are at play. Therefore, it is important that each ventilation situation be analyzed on a case-by-case basis to determine the best-fit solution for an operation. The ventilation design process should not necessarily be constrained by theoretical optimal economic velocities that become rules-of-thumb. In some cases, this could lead to unrealistic infrastructure requirements and exorbitant capital expenditure. This type of design often lacks corporate support leading to a scenario where no ventilation upgrades are implemented. Economic velocities typically consider the cost of power, development costs and operational risk. These typical rules-of-thumb work reasonably well as a starting off point when considering feasibility of greenfield projects. For established mines that are looking at expansion these rules may not be appropriate due to capital expenditure constraints or geotechnical ground conditions. The theoretical optimum should be reviewed in the case of an established mine where existing infrastructure could perhaps be maximized. For example, the geotechnical risk of large diameter raises at depth may require multiple small diameter raise to maintain the theoretical economic velocity. If a mine has a life of less than 5 years, then the cost of power is an insignificant proportion of the total owning cost. For these mines, operating the ventilation raises at an increased velocity to avoid a complicated and expensive capital upgrade might be the more appropriate option, even though it opposes the traditional rules-of-thumb. Mines which are capital constrained may be better off accepting a higher operating cost for the interim or settle for minor infrastructure upgrades rather than run the risk of the entire ventilation upgrade not being approved at all. This paper explores a number of examples derived from case studies undertaken by the authors for several deep mechanized mining projects in Australasia. The examples explore conditions under which higher than the economic norm would be applicable."

Jan 1, 2019

By J. Lobel, M. Bourassa, J. A. Kozinski, B. Peng

Non-isothermal kinetics studies of the reduction phenomenon of electric arc furnace (EAF) dust generated in stainless steelmaking have been carried out. The dust was mixed with carbon as a reducing agent and dolomite as a binder to form pellets. A Thermo-Gravimetric Analyzer (TGA) was used to determine the weight loss of pellets heated at an average rate of 40 K/min. up to a temperature of 1500°C. The degree of metal reduction was calculated by considering the pellet weight loss, and evaporation of moisture, dust, zinc and lead at high temperature. The reduction process was divided into three different steps. The first covers the 300°C to 760°C temperature range (from 7 to 18 min.), the second step ranges between 760°C and 980°C (18 to 24 min.), and the third covers temperatures above 980°C. Each step is characterized by different chemical reactions. Non-isothermal reduction kinetics equations were set up to describe each step. The kinetics parameters such as apparent activation energies and frequency factors were established. It was found that the first step was chemically controlled, while the second step was diffusion-controlled. Reduction behaviour in the third step was strongly dependent on the initial carbon content in the pellet. Chromium oxide (CrO) could only be reduced in this last step. High temperatures and higher initial carbon content favoured the reduction of CrO.

Jan 1, 2001

By A. S. Nortjé

At South Deep Gold Mine longhole stopes are backfilled using a cemented Cyclone Classified Tailings in its hydraulic state. The need to contain the hydraulic fill until cured requires a barricade. Due to the massive size of the stopes, the tailings can exert enormous forces on any such barricade. Barricades have long been in use, but recent failures in Australia and the large rate of filling required at South Deep solicited a robust design. A robust design must examine all foreseeable failures and the barricade must be able to resist all expected and, within limits, unexpected loads. The design should also be simple to construct and cost effective, limiting the impact of construction errors and unnecessary delays to production.

May 1, 2007

By S. Mostaghel, V. Hernandez, S. Ge

"The automotive industry is under a constant pressure to reduce the weight of vehicles in order to reduce emissions and improve fuel efficiency. As such, there is an ever-growing demand for high strength and high ductility steel grades to meet the need for lightweight automotive components. Over the past decade, the production and application of 2nd and 3rd generation Advanced High Strength Steels (AHSS) as a lightweight material in automobiles has gained significant popularity due to their exceptional mechanical properties. However, the production cost of these high manganese steel remains high, partially due to the need of large amounts of ferromanganese as alloying material in standard steelmaking processes.The current study introduces a new and cost-effective technology for the production of medium- and high-manganese steels, where self-fluxed micro-pellets of manganese ore will be used as the source of manganese that can be injected into the steel bath. Prior to injection, these pellets are subjected to a pre-reduction process using a mixture of H2 and CO gases, where partial metallization of iron and manganese will occur. Direct injection of the pre-reduced micro-pellets provides less volatilization/emission and higher recovery of manganese, and is capable of producing AHSS with 6–18 wt% Mn.INTRODUCTIONAutomakers are constantly searching for lighter, stronger and cheaper materials in an effort to create safer and more fuel efficient vehicles. The introduction of aluminum alloys and polymer composite materials for automotive applications has been carving into what is traditionally one of the most profitable markets of the iron and steel business. The steel industry responded with Advanced High Strength Steel (AHSS)—a family of manganese containing steels which exhibit exceptional strength and ductility."

Jan 1, 2016

By J B. McConnell

The Thompson smelter has three unique features which form the basis ~f its design: fluid bed roasters which treat nickel concentrate filter cake from the mill, as well as the flux, in order to achieve partial desulphurization; the use of electric furnaces for the smelting of the partially desulphurized, preheated roaster product; and the disposal of slag by water granulation and slag slurry pumping. The installation consists of three fluid bed roasters, each feeding an electric furnace. Nickel concentrate is received at the smelter via pipe line. It is thickened and filtered, and the filter cake, together with siliceous flux, is fed through rotary bin feeders and reciprocating double-gate seals into the fluid bed roasters. Air injected into the roasters through club-head tuyeres oxidizes part of the sulphur and associated iron in the concentrate. The heat of reaction dries and heats the charge. Roaster product is recovered from the gas stream in cyclones and from the roaster bed through automatic valves.

Jan 1, 1963

By Darren Medd

Kumtor Gold Company (KGC) currently operates the 500,000 tonnes per day Kumtor open pit gold mine located in the Issyk-Kul region of the Kyrgyz Republic at an elevation of more than 4,000 m. To supplement the open-pit mill feed with high grade underground ore from outside the current pit limits, KGC started pre-production design and development of the underground mine for the SB ore zone in late 2006. The initial phase of pre-production development consists of exploration and haulage declines which, upon completion, will provide ventilation and access to the underground mine. Design and construction of these declines presented many challenges to the project team considering the mines unique location at high altitude, the limited experience with Western underground mining techniques in the Kyrgyz Republic, and the impact of the nearby Davydov glacier and resultant ground conditions. Completion of the exploration and haulage declines was undertaken jointly by KGC and mine contractor, J.S. Redpath Limited (Redpath). The initial phase of development including several ground falls provided detailed information on geotechnical ground types and conditions that were useful in determining the overall mine design and methodology for production. This paper covers the various aspects of the design and construction process of developing the declines under the glacier, minimizing the likelihood of further ground falls, and the journey of both KGC and Redpath which led to the successful breakthrough between the declines on 01 July 2012.

Aug 1, 2013