Search Documents

The acid plant consists of the following units: 1. Glover tower. 6. Mills-Packard type chambers. 3. Reaction towers. 6. Gay-Lussac towers.The sulphur dioxide bearing gases, used in the manufacture of the acid, are obtained from the roasting of zinc concentrate. Six Herreshoff type furnaces are available, each with an effective hearth area of 520 sq. ft.The concentrate contains approximately 30% sulphur, of which about 72 is ultimately recovered as acid. The oxides of nitrogen are added to the gases in the requisite proportions partly from nitrous vitriol and from nitric acid in the Glover tower, and partly from nitrous vitriol in some of the chambers and connecting flues.The acid leaving the Glover tower is cooled by the ordinary water-cooling coils, while the cooling of the chamber gases is effected by circulating water over the outer surface of the chambers, and by spraying nitrous vitriol and weak acid into them.Flow of gases throughout the plant is regulated and controlled by means of regulus metal fans, fitted with variable speed gears.

Jan 1, 1934

By E Villaescusa, A Kusui

The depth of underground mines has been increasing due to several factors, such as material demand growth and improving technology. It is a challenge to understand severe failure mechanisms such as spalling, which is caused by induced high stress. To investigate this failure mechanism under high stress conditions, intact rock blocks with small size tunnel were tested at the Western Australian School of Mines (WASM). The range of rocks, such as sandstone and granite, were drilled (200 mm hole) and tested using a servo-controlled 450 t capacity INSTRON machine. The acoustic emission sensors were attached to the block mass during the experiment to investigate the seismic response prior to spalling failure. The effect of the ground support system towards the failure was also examined by comparing the seismic response of the various ground support schemes.CITATION:Kusui, A and Villaescusa, E, 2016. Seismic response prior to spalling failure in highly stressed underground tunnels, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 689–694 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J L. Mauk

 Broken Hills is an adularia-sericite epithermal Au-Ag deposit, hosted in flow-banded rhyolites and overlying rhyolitic pyroclastic rocks in the eastern Hauraki Goldfield. The 7.1 Ma deposit was the largest producer of gold in the eastern Hauraki Goldfield, and was one of very few economic deposits hosted in Pliocene rhyolites. This paper presents the results of a recent study in the upper levels of the deposit. Maps and cross-sections constrain structural and lithological relationships, and the lateral and vertical extent of a breccia pipe û the major feature of the upper levels.   Previous studies in the upper levels of Broken Hills have shown that gold and silver values are concentrated around and within a large breccia pipe, mined by a series of æcaveÆ stopes and in veins. Contour diagrams of Au-Ag data from channel samples indicate that the breccia pipe was a major fluid channel-way for mineralising solutions.   The breccia pipe deposits are part of the dynamic geothermal system that formed the Broken Hills ore bodies; they developed as a result of hydrothermal brecciation in areas of structural weakness within a rhyolite pyroclastic unit that overlies a massive rhyolite lava-flow unit. The main breccia pipe begins near the rhyolite/pyroclastic contact, having the shape of an inverted, inclined cone, and consists of silicified breccia, stringers of quartz, and irregular patches of clay-altered country rock. Smaller zones or pockets of hydrothermal eruption breccia are silicified and contain low grade gold in the matrix and in the adjacent silicified wall rocks.   Quartz has been classified according to its physical characteristics as seen in situ and hand specimens indicate that vein definition decreases upwards, perhaps as a result of changing lithological conditions and/or increasing proximity to the paleosurface. Hydrothermal quartz is widespread as veins and as a replacement mineral, or lining fractures and cavities and overgrowing rock fragments. Breccias contain vein quartz, but some quartz veins cross-cut breccias, indicating that vein and breccia formation was relatively synchronous and overlapped in time.   Disseminated gold-silver mineralisation is associated with vein quartz and silicic alteration of the wall rock within the breccia pipe. The auriferous zones are highly irregular and erratic, and sampling results show a wide range of gold-silver ratios, suggesting that highly volatile physiochemical conditions prevailed during mineralisation.

Jan 1, 2005

Tapira Mine (Tapira, MG, Brazil) is the largest phosphate ore and concentrate producer in Brazil. The mine is an open pit, which until recently operated with a large equipment fleet and now uses a smaller fleet operated by contractors. The annual production reaches 17 Mt of ore plus 14 Mt of waste at a stripping ratio of 0.82. Defining the geological boundaries and forecasting the annual production can be a difficult task if not performed on a reliable model. The geological model has been totally reviewed as well as the estimation process. Ordinary Kriging has been used to build the new block model with P2O5 and contaminant grades. After estimation, block model validation and classification criteria definition to assess resources and reserves, the result is given by the life-of-mine plan is defined after pit optimisation and design. The Lerchs-Grossmann algorithm implemented in the NPV Scheduler was used to define the long-term production targets based on the main parameters P2O5 and the contaminants that are just important to the beneficiation process.

May 1, 2010

ABSTRACTMechanised cut and fill stoping in the Racecourse orebodies between II and 9 levels was started in 1964.Five stopes are in progress over the two level interval, extracting the full strike length (600-2,000 ft) of each orebody without transverse pillars.Each stope is served by a central 10 ft by 12 ft service intake ventilation raise and an 8 ft by 8 ft return air raise at each end of the stope. Each stope is divided into two sections for drilling. firing. mucking, and fillingto maintain steady production. All equipment is kept in the stope for one level lift stoping. Gardner-Denver 2 boom jumbos are used for uphole drilling and Wagner ST 5 Scooptrams for loading and transport to ore passes located in the footwall of the orebody. A Wagner PTIO is used for materials handling and scaling of the stope backs.Mill tailings, after one stage of cycloning are used to fill the stope, one section at a time. About 80 per cent of the water is removed by decantation while the remainder percolates through hessian-covered pipes and boxes.The ore is passed to 11 level where it is hauled by the 3 ft 6 in. gauge train to the tipple at the shaft area. The ore is crushed underground before hoisting to the surface.A performance of about 100 ton/manshift is achieved by the drilling, blasting, and mucking crews in the stopes.

Jan 1, 1968

Metana Minerals commenced life in 1970 and graduated to a mining company in 1981 with the opening of a small alluvial tin-tantalite mine at Wodgina (W.A.) The present board of directors assumed control of the company in 1978 and established the exploration and development philosophies that have guided the company's expansion to its present status as an emerging diversified miner. An ability and willingness to raise equity capital when required has been a feature of the company. Company activities include exploration for gold, diamonds, heavy mineral sands, polymetallic (base and precious metals) deposits, strategic minerals, rare earths, oil and gas in a geographical distribution covering the entire Australian mainland Metana owns and/or operates four gold mines (Reedy, Mt Magnet, Youanmi and Howley) and at the time of writing is developing a fifth gold mine - its first underground mine - at Rothsay. In contrast to many similar or larger sized companies, Metana undertakes most activities itself rather than through the use of consultants or contractors. In-house services include: analytical and metallurgical laboratories, plant engineering design and construction, drilling and mining (earthmoving) Metana Minerals has established an enviable reputation for technical excellence and this expertise has placed the company in a sound position to continue its growth pattern into the future. This growth will be achieved through a combination of low cost and successful exploration and acquisition of suitable mines either directly or through corporate activity.

Jan 1, 1989

By Taylor R. G

This paper reports a biogeochemical study of the Siberia lode of the Herberton tin field. Soil near the orebody contained high levels of Fe, Cu, Pb, Sn, As, Mld Mn. Polycarpaea spirostylis and Indigofera dominii were associated with these high levels but several other species apparently could not tolerate them. The potential of these species as indicator plants is discussed.

Jan 1, 1975

By J Guo, K Williams, J Y. Guo, A W. Roberts, M Jones, B Chen

Numerical simulations using the discrete element method (DEM) were carried out to investigate the flow patterns and stress field redistribution at the hopper and feeder interface. The influences of different filling heights, belt speeds and clearances between the hopper bottom and feeder surface on feeder loads were studied. Meanwhile, experiments were conducted by utilising wedged plane-flow hoppers with different configurations and horizontal feeders with various clearances. The simulation results were compared with theoretical values and experimental measurements. In terms of the cases presented in this study, simulation results reveal good agreements with experimental observations regarding the flow pattern. Being similar to the theoretical values, the simulations provide close predictions on vertical feeder loads for steady flow states, but they may show significant overestimations for initial states. Additionally, suggestions are given for relevant simulation parameters based on the comparisons shown in this investigation.CITATION:Guo, J, Roberts, A W, Williams, K, Jones, M, Chen, B and Guo, Y J, 2017. Simulation investigation of flow patterns and feeder loads at hopper/feeder interface, in Proceedings Iron Ore 2017, pp 173–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By D A. McCallum

With depth, many gold ores become sulfidic with minerals such as pyrite, pyrrhotite and arsenopyrite becoming prevalent. In addition, many underground gold mines use tailings backfill to bind and store the waste. In these cases, acid mine drainage (AMD) can become an issue. One approach to the control of AMD is desulfurisation whereby the sulfide minerals are removed prior to disposal. Four sulfide tailings samples, representing different ore types and gold and base metal operations, were selected for assessment and testing using simple physical beneficiation techniques. The aim was to determine the extent to which mineral processing methods were suitable for separating sulfides from non-sulfides and for extracting potentially marketable by-products from the tailings. In order to streamline the testing procedure a simple diagnostic separation technique was developed to enable quick screening of bulk sulfide tailings for suitability for reprocessing. The testing procedure involved detailed characterisation and a sequential set of testing regimes based on simple unit processes including water washing, classification, gravity concentration, magnetic separation and bulk flotation. The preliminary test results indicate each unit process can play an important part in producing effective sulfide/non-sulfide separations and in generating useful by-products from the tailings. Potential valuable products identified include coarse, benign silica sands, bulk iron sulfide products rich in pyrite and/or pyrrhotite, high-grade iron products (magnetite) low in silica, low-volume bulk sulfide concentrates and low-grade molybdenite and talc products. The work presented shows how sulfide tailings can be viewed as a resource rather than a waste stream, and identifies a pathway for developing a more sustainable approach to the environmental management of sulfide tailings for the future.

Jan 1, 2007

Laboratory electrical resistivity measurements of rocks are reviewed. Inductive and galvanic methods are discussed together with the ten important experimental factors which should be considered in an investigation.These experimental factors are electrodes, sample preparation, measurement errors, temporal current variations, current density, frequency, electrolyte composition, electrolyte saturation, pressure, and temperature.

Jan 1, 1969

THE present article makes no claim to be exhaustive, since it cannot contain all the knowledge which scientists and manufacturers of the compounds of the rare earths have gained. The following notes are, therefore, simply an attempt to ascertain andclearly record the occurrence, properties, and uses of the more important of the rare earths, with a special reference to their commercial values and the industries based upon them.HISTORYIt was the mine manager, Gcyer, of Stockholm, who, in 1788, first drew attention to a black mineral which had been found in a quarry near Roslagen, in Sweden. In 1805 Klapproth received some specimens of this mineral, which he declared to be a newmineral. Subsequently Gadolin, professor of chemistry at Abo, analyzed the same mineral, and determined the presence of an unknown earth resembling alumina and lime. He named the mineral ytterbite, and afterwards gadolinite. Klapproth has alsothe merit of having detected (1804) another rare earth, which he named ochroit-earth, found in the Bastnas mine, near Riddarhyttan, in Wcstmannland, Sweden. Curiously enough, Hisinger and Berzelius simultaneously ascertained the existence of the same...

Jan 1, 1909

By P S. Heithersay, M McGeough

The discovery of Olympic Dam in 1975 and, more recently, Prominent Hill in 2001 and Carrapateena in 2005 demonstrates the potential for world-class IOCG deposits in South Australia. Potential for further discovery of large IOCG mineral deposits in the Gawler Craton and the Curnamona Province is high because of continental-scale pervasive iron-rich alteration, crustal-scale structural preparation and unique magmatic-hydrothermal conditions. Recent exploration successes point to the effectiveness of new exploration tools and technologies to locate this style of mineralisation under cover. The gold endowment of these orebodies located in South Australia exceeds 75 Moz, with further discoveries to come. The lead time between discovery and development of the multi-million ounce Prominent Hill copper-gold mine in less than seven years demonstrates how quickly this style of deposit can be brought into production in South Australia. Clearly these long-life, multi- commodity IOCG deposits mines are an immediate exploration and future growth opportunity for the gold mining industry to replace ever depleting gold inventories.

Jan 1, 2007

By W C. Burton, J S. Kuszma, T O. Aspinall

The environmental impact of mining and evolving environmentallegislation has received increased attention worldwide in the last two decades (Bradfield, Shultz and Stone, 1996). The potential impacts associated with unstable spoil dumps from mine operations is the focus of concern both by the mining industry, environmental regulatory agencies and members of the public. Engineered slopes of mine spoils may be stable at the end of construction, but they can deteriorate over time. There is thus the need to increase the base of knowledge on the existing practices of spoil dump design and rehabilitation. Efficient engineering design and systematic economic evaluation of spoil dump reshaping techniques for mine rehabilitation assists in maintaining the expected standards of environmental compliance. As part of the overall approach for effective engineering design ofspoil dumps, a comprehensive, computational and efficient tool isrequired for assessing the economics and productivity of existing spoil dump reshaping practices for efficient mine rehabilitation. Such a design tool is useful in linking current spoil dump environmental management practices with engineering design planning and economic impact evaluation. This paper identifies the processes for the economic impact evaluation for existing spoil dump reshaping practices and proposed final site dump designs. Selection of an efficient spoil dump design at optimum costs will ensure operational efficiency. A case study is presented identifying economic impact evaluation in earthmoving equipment selection and the costs involved for the reshaping of spoil dumps to that of varying final site designs.

Jan 1, 2000

The Waimumu area, 12 km southwest of Gore, is underlain by the Gore Lignite Measures, an early Tertiary fluvial sequence approximately 500 m thick resting on Triassic-Jurassic argillitic basement. The Waimumu Quartz Gravels (Pliocene) have been deposited locally and are in part due to the localised reworking of the Gore Lignite Measures. Structurally the area is dominated by the Dunsdale Fault System, a steeply dipping series of NE trending reverse faults (Isaac and Lindqvist, 1990). The Belle-Brook, Hedgehope and Parker Road sites sampled are adjacent to the downthrown (east) side of the Hedgehope Fault.The authigenic gold-sulphide association at Belle-Brook was discovered in 1987 (Falconer, 1987: Clough and Craw, 1989). Despite a very limited amount of alluvial mining a significant quantity of authigenic marcasite has developed. Authigenic sulphide trace element analysis has shown anomalous amounts of As, Ni, Cr and to a lesser extent Zn, Pb and eu (Table 1). It has been established that the nickel occurs as a colloform banded Ni sulphide, possibly bravoite, within the marcasite (Figures 1 & 2). Arsenic and nickel (re)mobilisation are well documented in the literature. Generally As and heavy metals are mobilised in the groundwater as a result of the oxidation of sulphides (ie as a result of mining). At Belle-Brook it is reasonable to assume the authigenic sulphide trace element composition reflects either localised groundwater contamination or hydrothermal mineralisation. This poster presents some preliminary findings.

Jan 1, 2001

By D Craw

Formation of gold-bearing veins in Otago Schist was intimately linked to the structural evolution of the schist belt. The currently-exploited Macraes gold deposit formed in a regional scale shear zone during latemetamorphic uplift of the schist belt. Further exploration for this type of deposit will be facilitated by an increased understanding of the late-metamorphic structural evolution of the schist belt. To this end, a three-dimensional cross section through the Otago Schist has been drawn using structural data gathered at outcrops in a 20 - 40 km wide transect across central Otago. This is the first continuous detailed structural section to be drawn through the belt. The section spans an area from Textural Zone 1 metagreywacke of the Torlesse terrane in the northeast through TZ 4 schist in the central region and across the Caples-Torlesse boundary to Textural Zone 3 schist of the Caples terrane in the southwest. Two different late-metamorphic structural generations are identified in this section: the long-recognised Manorburn Generation, and a new æPoolburn GenerationÆ. The location of the Caples-Torlesse boundary has been refined on this transect by field mapping combined with whole rock geochemistry.

Jan 1, 2001

The history of soft and hard rock underground mining is blemished with regional instabilities of mine workings. Whilst the potential consequences of regional instability events are recognised to be high, there is a false perception that the probability of them occurring is very low. In fact, Australia has averaged more than one event per year for the past 20 years. At least five fatalities and over $100 million of losses have been associated with the events. As such, they are a core risk to underground mining and have a significant effect on the quadruple bottom line of business û safety, environment, community acceptance and economics. This paper explores the important roles that risk management has in reducing the probability and consequences of regional instabilities. It concludes that education and continuing professional development are essential elements for effectively managing the risk.

Jan 1, 2003

Recent work on decoppering lead is reviewed CUS is formed rapidly even from dilute solutions of copper in lead. The mechanism of decoppering is discussed and an explanation for the retention of metals such as silver in lead is advanced. As decoppering tin appears to be an analogous process, the, Cu-Sn-S system is studied at 300°C.. CuS, which is not an equilibrium product, is found m decoppermg drosses. In the removal of nickel from lead, Ni3Pb2S2 is formed; preliminary measurements show the equilibrium nickel content to be greater than that obtained by stirring in sulphur. Decoppering bIsmuth IS thermodynamically favoured, but is complicated by the occurrence of CuBiS2 The Cu-Pb-S system IS the only one of the four studied where the equilibrium can be calculated simply, as the presence of ternary sulphIde or other phases invalidates calculations based on binary data.

Jan 1, 1971

By T Salles, G Duclaux, E R. Ramanaidou

In a continental environment, sediment mobilisation, dispersion and deposition are mainly controlled by mass gravity and streamflow processes. Alluvial sedimentary systems have an important economic value because of their capacity to host mineral resources. In the Hamersley Province, alluvial iron deposits (including the well-known detrital iron deposits and channel iron deposits) play an increasing role on the commodity market. Alluvial deposits exploration is challenging and generally involves geomorphologic and stratigraphic field studies, as well as expensive exploratory surface sampling and drilling. We applied a new surface processes modelling technique to investigate iron rich material, ie the erosion product of bedded iron formations -dispersion in the Hamersley Province. LECODE is a 3D-parallel surface processes forward modelling code designed to compute surface flow and solve erosion, transport and sedimentation on the geological time scale. The code offers new quantitative ways to better understand how sedimentary deposits develop in intra-continental and channel environments. Here we show that our integrated forward model is capable of opening a window to the construction of sedimentary architectures, including facies distribution, deposit thickness and development of heterogeneities such as mineral traps over the modelled domain. The model results represent 1 Ma of surface evolution and are validated through comparison to published paleovalleys map and known occurrences of iron ore deposits. This numerical modelling approach allows for the first time to track alluvial materials from source to sink through time, test existing geological models and faithfully reproduce the first order distribution of alluvial iron deposits in an area of interest. This work strongly suggests the presence of iron rich alluvial deposits reserves under cover, in unexplored detrital fans in the Fortescue Valley. This method, potentially coupled with sediment geochemistry and basin analyses studies, has the potential to maximise alluvial iron deposits exploration success, while reducing exploration cost and associated environmental impact.CITATION:Duclaux, G, Salles, T and Ramanaidou, E R, 2013. Alluvial iron deposits exploration using surface processes modelling - a case study in the Hamersley Province (Western Australia), in Proceedings Iron Ore 2013 , pp 75-80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Many mining operations are uncertain of what costs they should be achieving. The majority of cost estimates are based on historical costs that have added contingency factors. Historical costs are a valuable source of information but a more precise costing method is necessary. There are several alternative methods for predicting costs. A methodology which provides the best indication of the achievable costs is one using a standard inventory list and a bill of quantities. The model is termed a Basic Principles model and addresses basic design principles and engineering constraints.

Jan 1, 1990

By J Hall, A Gallardo, M Strizek

Mineralogy and coproponents Sino Iron, International Minerals and Austeel are in the process of developing four world class magnetite iron ore mines with multiple open pits along a 25 km strike length of Brockman Iron Formation to the south of Cape Preston on the West Pilbara coast. The close proximity of the proposed pits raises some challenging project approvals and environmental management issues relating to the impacts of dewatering at individual projects and the cumulative impacts of progressive development on local and regional groundwater resources, which includes a large fresh water aquifer system in the Fortescue River alluvium.This paper presents an outline of the hydro-environmental impact assessment process adopted and the key result that the cumulative impacts of dewatering at all four projects on the local brackish groundwater system in the basement rocks is only marginally more than the impact of any one project on its own, and that the impact on the Fortescue River alluvium aquifer is negligible. The paper also presents an outline of the proposed integrated water management approach that will involve coordinated monitoring, ongoing impact assessment and management, and reporting programs for all projects.

Jan 1, 2009