Search Documents

By P J. Howard

Atlas Iron Limited’s McCamey’s North project lies at the eastern end of the Hamersley Basin, approximately 50 km east of Newman, Western Australia, and 3 km northeast of BHP Billiton’s Jimblebar Mine. The presence of significant surface iron mineralisation identified during field reconnaissance, has subsequently been further defined by detailed mapping and RC drilling.The project area is dominated by outcrops of moderate to steeply north and south dipping banded iron formation, cherts and shales of the Boolgeeda Iron Formation overlying rhyolites and rhyodacites of the Woongarra Volcanics. In lower lying areas recent colluvium and alluvium mask the Archaean geology. Drilling and downhole geophysics has allowed a composite stratigraphic section to be compiled through almost the entire Boolgeeda Iron Formation.Surface orientations and subsurface stratigraphic correlations using natural gamma logs indicate large scale open folding about east-west trending fold axes across the project area; while small scale tight to isoclinal folding with similar fold axis orientations are visible at the outcrop scale. These folds are cut by a number of moderate to steeply south-dipping normal faults defining a series of north-dipping fault blocks which repeat the stratigraphy across the project area.Bedded iron mineralisation consists mainly of haematite-martite and goethite ores with best results of 78 m @ 60.5 per cent Fe. Vitreous goethite is observed at the surface of the mineralised horizons. The mineralisation exhibits a strong stratigraphic control and extend down-dip up to 120 m below surface. The strike extent of the mineralisation is still to be determined. An inferred resource of 39 Mt at 58 per cent Fe has been defi ned to date (ASX: AGO 3 February 2011).The fi ndings at McCamey’s North indicate that there is potential for economic iron mineralisation to exist in other areas of Boolgeeda Iron Formation within the Hamersley Basin.

Jul 11, 2011

The basic make-up of the majority of currently produced bulk explosives has changed little in the last 20 years. These explosives would be described as mature in a life cycle analysis. Therefore these explosive products and the practical rules for their use are well understood and well established. In recent years there has been interest in low density explosives, predominantly due to ammonium nitrate shortages and the associated increase in the cost of explosives. In the use of low density explosives some of the practical rules for the more commonly used bulk explosives do not apply. Therefore a shift in the thinking among users is required. At a number of mines low density explosives have been trialled or are being used, utilising the practical rules that apply to bulk explosive products. This has led to poor blast results in many situations. These poor blast results have often then led to a reduction in the use of low density explosives at the mine. This reduction does not acknowledge the advantages that can be gained from this product in the area of reduced cost of mining. This paper looks at low density explosives and discusses how and why these products work. Included in the paper are some practical ideas and examples of how low density explosives can be effectively used at the mine site.

Jan 1, 2007

By A Gustafson, G Shekhar, P Boeg-Jensen

The amount of material extracted from each blasted ring in sublevel caving mines is vital when deciding the overall mine production target. The orientation of the production drifts is normally perpendicular to the strike of the orebody, and rings are blasted from the hanging wall side to the footwall side in a retreating manner. For an inclined orebody, a given ring will contain different amounts of material based on its relative position along the production drift. This layout creates a distinctive problem with respect to the extraction ratio optimisation along the axis of the production drift. This paper describes the current drawpoint control strategy practiced at LKAB and presents the variation of drawpoint performance parameters along the production drifts. It uses automatically generated data from a bucket weighing system that measures tonnage drawn per bucket, and it classifies the blasted rings into four zones based on their relative position along the production drift. It considers the loading procedure for blasted rings at Kiirunavaara mine and analyses the variations in drawpoint performance along the production drift. The paper finds that although the current draw control strategy is sensitive to ring position along the drift, it could be modified to optimise the final extraction ratio.CITATION:Shekhar, G, Gustafson, A, Boeg-Jensen, P and Schunnesson, H, 2016. Draw control optimisation along the production drift in sublevel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 241–250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Education for the Mineral Industry in Australia developed in an uncoordinated but effective fashion till the mid 1960's, with recognised quality in graduates, with output matching demand, and with industry needs being fulfilled. Then in the space of a further 20 years, as company structures expanded, as the number, complexity, and costs of mineral projects escalated, as educational facilities, costs and politics increased, as community perceptions and aspirations changed, as government control of minerals and education increased, and as mineral sales cycles and markets fluctuated widely, the very fabric of Australian Mineral Education fell in tatters. Extractive Metallurgy Education suffered most in this collapse, and no compre- hensive remedies have been initiated. We are all the losers. In the 1990's, the extraction of Australian minerals and metals will increase in international significance, and the education of Extractive Metallurgists must meet this need. After examining the current situation, a series of management strategies are proposed to enable Extractive Metallurgical Education to survive and prosper in the next two decades and beyond. These strategic proposals involve industry, the government, the educational bodies, and individuals, in a range of short and long term objectives, policies, and actions.

Jan 1, 1984

By D S. Perera, P Wal, D C. Southam, J L. Lowe

The Cooperative Research Centre for Sustainable Resource Processing (CSRP) is undertaking a large research project involving partners from industry, universities and government, which aims to develop the necessary chemical and structural understanding of geopolymer materials made from waste products for them to be used to capture a significant market share of the concrete business for a given industrial region. We are investigating the suitability of a range of soluble silica-bearing waste streams for use as geopolymer concrete feedstocks. In order to utilise a variety of waste streams, either singly or blended, an understanding of the role of secondary metal ions (Fe, Ca, Mg, Ti, etc) in the geopolymerisation process is essential. A range of experimental and analytical techniques is therefore being used to better understand the structure-chemistry-property relationships of geopolymers. Currently, we are investigating geopolymers made from a variety of waste streams (fly ash, kaolinite, red mud, etc) available in the Kwinana Industrial Region, Western Australia. This paper will detail how the basic scientific research underpinning the project is vital if waste streams of varying composition are to be successfully used in a commercial concrete product and the regional synergies required to develop geopolymers from waste streams.

Jan 1, 2006

By S L. Barbour

Measurement of the net percolation from the base of a cover system into the underlying waste material is a key component of a cover system monitoring program. The units of measure (ie a percentage of precipitation or rainfall) are simple to understand for all stakeholders, which increases the importance of obtaining representative net percolation values. In general, lysimeters are used to measure net percolation across the cover material-waste material interface; however, the design of lysimeters for cover system monitoring programs in the mining industry have typically not considered fundamental aspects of lysimeter design. Lysimeter design is typically thought of as being conceptually simple, when in reality the design, installation, and operation of lysimeters is often counter-intuitive, due to the complexities of flow through unsaturated soil systems. This paper puts forward a methodology for lysimeter design while also presenting the fundamental design variables that should be considered. Lysimeter design for differing climates, cover materials, and waste materials is discussed. Finally, the performance of lysimeter designs previously installed in the field at sites in Australia, Canada, and the United States are subjected to numerical modelling to determine whether net percolation is being measured properly.

Jan 1, 2003

By I Canbulat, G Si, Y Duan, X Luo

The presence of unfavourable geological structures such as faults and dykes often can contribute to coal burst risk. Seismic events associated with rock fractures tend to cluster around these structures and it is important to understand the characteristics of seismicity for coal burst risk management. In an Australian underground longwall coalmine, two clusters of seismic activities close to the longwall face and within a section of the maingate roadway which was intersected by a major dyke were respectively identified. The induced seismicity in the dyke-roadway area was closely related to the longwall mining. These seismic events were located and the distribution of seismic events shows that more fractures were distributed on the inbye side of the dyke. The spatial-temporal changes of the seismic event locations delineate the fracture propagation as the longwall mined through the dyke. The frequency-magnitude relationship of seismicity was analysed and it was found that it changed significantly when the longwall was mining towards, through and past the dyke. The monitoring results demonstrate that because of the stiff dyke, the seismicity was intensified in the roadway section. It proves that the dyke promoted stress re-distribution and seismicity in its vicinity. More fractures were induced in the hanging wall of the dyke, whereas less strain energy was accumulated and released in the footwall of the dyke.

Nov 29, 2022

By D Nieuwkerk, V J. Absolon

"Screw press technology is an innovative approach to tackling the growing pressure to conserve water and minimise the environmental impact of mineral tailings disposal. The principles of the technology have been known for a considerable period of time in non-mining applications such as water treatment, wastewater (municipal sludge), as well as in the paper and chemical industries for dewatering solids, particularly those containing clays.The screw press represents a viable niche technology for filtering fine and high-clay tailings, without the prior thickening stage, and is capable of producing a filtered product that is sufficiently consolidated and dry enough to provide a product suitable for conveying and dry stacking.The Ishigaki screw press was introduced in 1990 and key features are: continuous operation and excellent availability low wear to plant acceptable flocculant consumption low carbon footprint and low noise levels fully automatic.These features lead to simpler plant layouts, easier maintenance, smaller spares inventories, reduced wear, smaller footprint and overall lower capital and operating costs.The amenability of a particular tailing stream to treatment by screw press technology may be determined by test work. Two pilot plant studies are described where this technology has been applied in the mineral industry being flotation tailings from a rare earth (RE) mineral concentrator and coal tailings. In addition, preliminary details are given of an ACARP sponsored research program titled ‘The application of screw press filtration in tailings dewatering’.CITATION:Absolon, V J and Nieuwkerk, D, 2014. Innovative use of screw press filtration in tailings dewatering plant design, in Proceedings 12th AusIMM Mill Operators’ Conference 2014, pp 449–456 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 1, 2014

By Medhurst TP, Trueman R, Hutchinson IN

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.] Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production. Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required.

Jan 1, 1992

By Dawson CF

About 17% of the world's present day oil supplies comes from wells drilled in the continental shelf of some 28 countries. The demand for oil is increasing each year and is expected to quintuple in the next decade. In the same period, the demand for gas will climb to at least 20 times its present rate. In the next decade, the percentage of oil and gas obtained from offshore is expected to rise to nearly half the world's consumption. The offshore oil industry is currently striving to achieve new technological advances in the field of deep ocean operations, especially in face of adverse seas. While the emphasis was put on drilling vessels for exploration, the industry was slow in developing effective offshore construction vessels. Until a year ago, construction vessels were but large barges with construction equipment mounted on their decks. These vessels all shared the same severe limitation: When the sea exceeds a five-foot wave height (and in some cases as little as three feet) the conventional construction barge is forced to suspend operations. In face of an oncoming storm they must run for shelter. Their utilization, therefore, is limited and in rough weather areas, such as the North Sea or the Bass Strait is lower than 50%.

Jan 1, 1970

A new engine family has been developed by Caterpillar Tractor Co. for application in off-highway trucks. This family, the 3500 Series is available in three configurations, covering a 600-1200 kilowatt range. This engine series incorporates the latest in design technology, stringent functional specifications for servicing ease, fuel economy, reliability, optimum performance and parts interchangeability. TECHNICAL INTRODUCTION The 3500 Series Engine has been under development by Caterpillar for over eight years and has undergone extensive testing in the laboratory and in field prototype units. - The engine configuration is a 600 Vee in 8, 12, and 16 cylinder versions. - The intermittent power output per cylinder is 75 kilowatt (100 HP). Net power for off-highway trucks is 600-1200 kilowatt (800-1600 Hp) depending on engine configurations. The 3512 (3500 Series Engine 12 cylinder Vee configuration) was the first model of the 3500 Series released. These engines offer optimum user value in terms of product durability, reliability, fuel consumption, performance and installation flexibility. Additional features of 3500

Jan 1, 1982

Jan 1, 2004

Cannington Mine is an underground, hard rock, metalliferous mine located in North-Western Queensland, Australia. Weld mesh is installed to prevent the failure of rock from between the installed reinforcement elements. Corrosion reduces the capacity and life expectancy of mesh and presents a real hazard to underground personnel and equipment as it reduces the effectiveness of the support system. Corrosion influences the economics of the mining operation through the need to conduct rehabilitation of the ground support which involves re-installing new mesh or shotcreting over the affected mesh to protect it from further corrosion. The requirement for rehabilitation is determined by the geotechnical engineer based on an individual visual assessment with little or no engineering input. It was identified that a more quantitative method was required that considered the safety and economic risks involved. A project was undertaken to develop a simple method to evaluate corroded mesh and to provide selection criteria for rehabilitation. A weld mesh corrosion classification has been developed that relates the average wire diameter of corroded mesh to the remaining capacity of the mesh. Accompanying selection criteria provides recommendations as to when rehabilitation may be required based on the estimated residual mesh capacity, the remaining development life, and the level of personnel exposure.

Nov 25, 2010

By S Jahn, M Noel, E M. Rykaart, M Pau

Three soil cover test areas were constructed on waste rock backfilled into the Lichtenberg Pit, near Ronneburg Germany. A fourth, uncovered area was included as a control. Each test area measures 50 m by 65 m, and was constructed using full-scale equipment and construction practices. Extensive material sampling and testing was included as part of the construction. Devices were installed in each plot to monitor meteorology, infiltration, run-off, interflow, soil moisture, soil temperature, and soil pore gases. Boreholes were completed in each area and instrumented for temperature, pressure and pore gas sampling to a depth of approximately 60 m. Data from the monitoring instruments have been collected since July 2000, and have been comprehensively analysed and modelled on two occasions. The paper presents an overview of the test area design and instrumentation and the results of the two comprehensive data reviews. The reliability of the various monitoring methods is discussed and experience with several innovative methods is reviewed. The difficulties encountered in modelling the data set using common soil physical models are discussed.

Jan 1, 2003

By Koppe J. C, Costa J. F C L

This paper compares different results for overburden volume estimation assisted by geoestatistics, particularly using kriging methods. The main goal is to obtain the most reliable digital terrain model for the calculation of the overburden volume. The data was collected on an irregularly spaced grid and interpolated values were calculated to provide a denser, more regular data set before volume estimation. The field work was developed at the Butia-Leste Coal Mine, southern most Brazil, where an accurate survey was done using a total station theodolite with electronic data collector. The study was developed in five main steps: data acquisition, exploratory data analysis, spatial continuity measurements, point and block kriging estimation and verification of the results. Data acquisition was carried out on a 5 x 5 in grid. This dense grid provides an exhaustive data set of the real terrain against which data subsets can be compared for the various interpolation procedures and volume calculation. This provides an interesting insight into the influence of the number of data on the estimation error. Univariate statistics were used to compare each data subset and the exhaustive dataset. Ordinary kriging on the data subsets followed by contouring was carried out using Geoeas and Surfer software respectively. A subroutine written in C provided the link between the files generated in Geoeas and subsequent contouring routines embedded into the Surfer package. Omnidirectional and directional variograms were modelled defining the parameters for kriging estimation using Geoeas. Different variogram models were checked through cross validation prior to kriging. A comparison between the magnitude of the differences in volumes calculated with the different DTMs was attained. These final result indicates the sensitivity of the volume obtained to the number of data points. As the number of data points increases the estimation error decreases, but at some point there is no significant decrease in the final volume with the collection of additional data.

Jan 1, 1995

By MacDonald AJ, Raffield MP

The South Deep massive orebody consists of 20 to 30 in of payable conglomerates ranging in dip from 11¦ to 20¦ and at depths of between 2400 in and 34(10 in. The mine design process selected a mining method with a proven record of application that could be adapted to overcome the inherent difficulties associated with the depth, thickness and structural influences of the South Deep orebody. A modified cut and fill mining method provides a concentrated and highly flexible method of extraction. An integrated destressing cut will enable the modification of the stress environment such that it is suitable for massive mining operations. The choice of backfill type and stoping width in the destressing cut ultimately determines the characteristics of the stress modification and, as such, is critical to the success of the cut and fill operation. This paper discusses the decision process undertaken to determine the optimum backfill type and stoping width combination in terms of, conditions in the destressing cut faces and in the massive mining environment. Numerical modelling has been extensively used to analyse arious scenarios to aid in the decision process.

Jan 1, 1998

By K Jupp, T J. Howard

Cliffs Natural Resources Pty Ltd (CNR) operates iron ore mines in the Koolyanobbing region of Western Australia. Ore is mined from three locations, separated by many kilometres. The ore is stockpiled at these locations, according to an in-house ore classification system (based on grade and source) and then trucked to the crushing and screening plant at Koolyanobbing. Lump and fines products are railed to Esperance for ship loading and export to Asian customers. CNR prides itself on the relatively low inter-shipment grade variability of the products. The Koolyanobbing crusher is fed using a daily blend plan, generated to maintain lump and fines product grades within acceptable tolerance ranges around targets. Achieving low variability requires predicting lump and fines grades as accurately as practical from the estimated head grades of the ROM ores potentially going into the blend. The grade prediction model may be either a direct prediction of crushed lump and fines grades and lump percentage, or be split into two stages: the bias between blasthole estimated head grade and crusher head grade and then the lump-fines algorithm for splitting the head grade between lump and fines products. The lump-fines algorithm comprises the percentage of lump and the difference between the lump and fines grades. We describe a weighted least squares (WLS) regression model for predicting crusher grades and lump proportion from the estimated head grade for Fe, P, SiO2, Al2O3, Mn and S. The method is applied to CNR production data, where the regression model explains approximately 60 per cent of the variance in the crushed ore grade, for both lump and fines. A further small but significant improvement in prediction can be achieved by including the ore classification data in the model. The regression errors exhibit strong positive serial correlation, indicating trends in grade error across multiple blend records. To compensate for the longer-term error, an exponentially smoothed model was developed and applied to the daily grade blend errors. This gave an increase in the longer-term variance explained and therefore an improvement in grade prediction.

Jan 1, 2009

By K L. Olzard

At the WMC Resources Phosphate Hill operation, monitoring the quality of the ore delivered by the mine to the beneficiation plant is of prime importance to ensure the fertilizer is produced cost-effectively through the various stages of production and meets customer quality requirements. P2O5 and Fe2O3 are among the critical-to-quality elements. Fe2O3 is a key performance driver as it is an impurity that adversely impacts some of the chemical processes. The ore is supplied to the plant on a conveyor belt that is equipped with an automatic sampler. Increments are taken off the flowing ore stream at regular time intervals. A variographic experiment was conducted to investigate sampling strategies capable of estimating ore properties over a 12-hour shift to a nominated level of precision. The combination of individual increments into a shift composite was included among the strategies that were assessed. The experiment involved collecting data at regular time intervals and preparing variograms to characterise the feed-grade variability on the conveyor belt. Duplicates were also collected to assist in quantifying the precision of the subsampling stages of the sampling protocol and assay accuracy was monitored with matrix-matched standards. Various sampling schemes were evaluated by combining geostatistical techniques and the sampling theory of Pierre Gy. The following parameters were varied: the number of increments, the increment-size reduction leading to the composite, the masses of the subsequent sampling stages and the number of analytical determinations. This paper describes the planning of the variogram experiment, the various phases of data collection and the methodology used to process the data. It discusses the development of some of the sampling schemes that were considered.

Jan 1, 2005

By J Miedecke

A metalliferous mine has operated at Storys Creek from the 1890s to 1979. Storys Creek drains from a pristine catchment and National Park and remains as the most degraded stream from historic mining in north-eastern Tasmania. It has been the subject of public concern since the closure, particularly at times of high rainfall such as existed in 1985 and 1986. The mine is located on the banks of the creek, which flows into a major river, the South Esk River, which is one of TasmaniaÆs largest rivers and important for recreational fishing and water supplies. For much of the life of the of the operations tailings were directly discharged into the creek, and in latter years stockpiled or very close to it. Little rehabilitation was carried out at mine closure. The result was erosion and subsequent deposition on the banks of the creek downstream. Direct emissions of adit water and the consequential emission of contaminated ground water to the creek continue to affect water quality. Contaminant loads discharging from the mine and tailings comprise 70% of the metal load in the catchment and are by far the largest single source. Acidity data suggested that the introduction of systems to introduce alkalinity could be effective in ameliorating the residual acid drainage impacts in the Storys Creek catchment. After a period of investigations and trials which proved their effectiveness, treatments adopted have included the following: relocation of tailings to a constructed and clay capped disposal area and rehabilitation of tailings area; crushed limestone addition to stream flows; crushed limestone addition to creek banks and exposed tailings; sealing of a drainage Adit; and construction of an anoxic drain to generate alkalinity to surface waters draining to old mine workings. These innovative treatments have resulted in a marked improvement in water quality draining from the area. The anoxic drain is believed to be one of the few, if any, which has been constructed to have generated high levels of alkalinity from clean waters and offers a solution to the clogging problems experienced in such drains in the past. Similarly, the use of crushed limestone in an active stream has proved effective in buffering acid drainage and removing metals from solution.

Jan 1, 2003

By Z-Y Pi, B Zhang, S Wen

"The paper introduces the structure and work processes of outside auger hollow claw tipped mechanical sampler for coal. Twenty sets of claw tipped sampler performance tests show that: The design of inner hollow cylinder-type (?180 mm) can ensure to take a coal sample with nominal top size of 60 mm. Built-in self-cleaning piston pusher ensures no adherence and blocking of the sample. The operation practices show that the mechanical sampler can operate in order for taking coal sample with up to 16 per cent of total moisture. Claw closing design can avoid sample leaking or spilling during the claw lifting and ensure the integrity of primary increment. Ultrasonic positioning device makes the sampler capture the materials no less than 10 cm from the bottom of the wagons, basically meeting the requirement taking full depth of the sample. The precision and bias test indicates that the moisture and ash have no relative bias under the sampling process; the sampling precision is in accordance with the requirement in IS013909.At present, the spiral mechanical sampler is widely used for coal sampling but there are many limitations during application, for example: It is difficult to capture a large size sample, so the size range of a coal sample taken is limited. There is easy adhering or blocking for high moisture coal, which will result in the mixture of different increments, wear of sampler and the difficulties for cleaning and maintenance of sampler. It is difficult to capture the coal sample at lower than 30 cm from the bottom of the wagons, in order to avoid damage of the vehicle. It is possible for coal sample loss and spilling during the sampler lifting, due to the unsealed sampler.For the outside auger hollow claw tipped mechanical sampler designed for solving the above problems, the opening distance of the claw is the opening size of the sampler and makes the size range of the coal sample to be taken wide. During sampling, the two pieces of claws open and the sampler rotates vertically downward to capture an adequate coal sample after reaching the specific point. Then the two pieces of claws close tight automatically to ensure there is no coal leaking or spilling. The inner pusher of the sampler will prevent from the adherence and blocking of the coal sample effectively.CITATION:Zhang, B, Pi, Z-Y and Wen, S, 2012. Outside auger hollow claw tipped mechanical sampler for coal, in Proceedings Sampling 2012, pp 41-44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012