Search Documents

By G Veillette, B Parker, S Hart

This paper provides a history of the challenges that were experienced while treating both the clayey oxide gold ores and the supergene copper-gold ores at the Boddington Gold Mine during the period 1989 to 2001. However the bigger challenge was to find a process flow sheet that would allow the economic treatment of the large low-grade competent gold-copper resource that underlies the oxide and supergene gold resource. Metallurgical test work and engineering studies on this resource started in the mid 1990s and culminated in the approval in 2006 of the 35 Mtpa Boddington Expansion Project to treat this material. The process flow sheet provides the basis of an energy efficient comminution circuit that includes high pressure grinding rolls and a treatment circuit with gravity separation, flash and conventional flotation to produce a precious metal low-grade copper concentrate followed by cyanide leaching of the rougher-scavenger and cleaner tailings streams. The treatment circuit allows maximum removal of copper minerals prior to cyanide leaching and so provides an environmentally responsible tailings disposal circuit.

Jan 1, 2007

By Hirst H, McAfee J

In December, 1934, Mr. R. Sussex extruded some silver lead alloy wires in order to determine their electrical resistance. After the determinations had been made each wire was threaded through a sheet of paper on which the composition was noted. The wires were placed in a more or less tangled mass in a cupboard in March, 1935. It was not until September, 1936, that they were re-examined, and it was found that during the eighteen months some of the wires had corroded very badly. It was not until March, 1938, that the wires and the corrosion product could be examined, and the results are given in the following pages. It is of interest to note that none of the numerous silver-lead alloys which have been used for creep testing in the rolled condition have shown a similarphenomenon. The silver content of the rolled alloys was, however, never greater than 0·1%.GENERAL APPEARANCE OF THE CORRODED WIRESThe wires contained 0·1% up to 28% of silver, and a general examination showed that the corrosion had progressed farther the higher the silver content. This can be seen in Fig. 1, which is a photograph taken in March, 1938, of typical wires at a 'magnification of five diameters. In the early stages the corrosive action seems to be localized and an area of grey, yellow or reddish brown powder appears. The grey corrosion product is by far the one, most frequently seen, and in the later stages the only one visible from the outside. The reddish coloured product is sometimes seen on the residual metallic centre when the grey product has been broken away.The irregular extent of the corrosion can be seen in Fig. 2, which shows (natural size) the 5% silver wire after standing two years. The corroded parts are seen to be much thicker than the slightly corroded ones. The corrosion product, being non-metallic, is quite brittle and falls away from the wire on bending. In the extreme case the' whole wire has corroded and presents a cracked appearance as seen in Fig. 1 (281% silver).An approximate idea of the extent of corrosion can be obtained by measuring the diameter of the corroded part. The original diameter in each case was ·050/ ·051 inches and in Table I are given the diameters of the corroded parts after Hand 3 years respectively. When the diameter...

Jan 1, 1941

The consideration of environmental constraints and issues is a fundamental component of all stages of planning, development, operation and decommissioning mining and quarrying projects. Provision needs to be made at all stages for the cost of environmental components since it is of fundamental importance that they be recognised as an integral component of any project. This paper presents an approach to environmental costing, suggested levels for budgeting, and the cost benefits.

Jan 1, 1990

By H Sofatzis, J Kinal, J Siliezar, B Kirkwood

Ernest Henry Mining (EHM) is a copper, gold and magnetite mining and processing operation located 38 kilometres north east of Cloncurry in the Mount Isa - Cloncurry mineral district of north west Queensland, Australia. The EHM ore body is an iron oxide copper gold deposit with an average grade of 1.1 percent copper, 0.5 g/tonne gold and 22 percent magnetite.At the end of 2009, after a series of promising laboratory test work, EHM converted the ball mill media charge from forged steel to high chrome media. Laboratory test work also indicated that with the use of high chrome media, the pH was able to be reduced with no negative impact on plant performance. At high pH values (above 10.5), the forged media is passivated, so as the pH of the system drops the media corrosion rate increases and floods the system with corrosion products, affecting flotation. As the high chrome media is much more inert, pH has less of an effect on copper flotation response.This paper provides an overview of the effects of reducing the pH in the EHM copper rougher flotation circuit. The pH in the roughers was dropped from 10.6 to 9.6 to determine the impact on the rougher performance and the subsequent performance of the whole copper flotation circuit. It was found that there was a slightly increased improvement in copper recovery and no statistical change in either the rougher or final copper concentrate grades for copper and gold.With the reduction in pH, there was a noticeable reduction in lime usage from 0.85 kg of lime per tonne of ore processed to 0.55 kg/t. This reduction in lime is equivalent to approximately $700,000 per annum at current production rates.CITATION:Kirkwood, B, Kinal, J, Siliezar, J and Sofatzis, H, 2013. Low pH trial in the Ernest Henry Mining copper rougher flotation circuit, in Proceedings MetPlant 2013 , pp 371-377 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

IF a straight line should be drawn on the map (See 1, page 96) through the northern half of the South Island of New Zealand, from Mt. Domett in the north to Arthur's Pass in the south, and another line drawn parallel to it and at a distance of ten miles to the west, according to the topographic scale, it will be found that within the belt thus drawn across the country all the most important mines, past and present, of the South Island are situated, with the exception of a few in Otago.The most important product of this tract being gold, and Reefton, the most important southern mining field, being situated at about its central portion, the zone may aptly be termed "The Great Reefton Gold Belt." The occurrence of so many gold mines along this particular strip of country is not at all a matter of chance, but is the outcome of cause and effect. Running along the eastern side of the gold belt are the Brunner and Victoria Ranges, which are chiefly composed of crystalline schists and metamorphic granite of probably Cambrian or Silurian age; between these and the gold-bearing series there are interposed at one or two places some beds of slates, limestones, and...

Jan 1, 1910

An Innovative Process for Comprehensive Utilisation of Clay-Vanadium Ores By adopting conventional processing technologies such as flotation, gravity concentration, and magnetic separation, it is difficult to enrich vanadium mineral effectively. At present, vanadium extraction process usually has not the mineral processing enrichment procedure, but rather uses direct hydrometallurgical process: roasting - leaching - precipitating vanadium for obtaining high quality V2O5 product. But it results in problems, for instance, high consume of auxiliary materials like acid and alkali, serious pollution and high cost of vanadium extraction. In the project study on the ore of a certain clay vanadium mineral, by adopting the test process: scrubbing raw ore with reagents added in - dispersing and segregating with reagents - grading enrichment, vanadium concentrate product with higher grade was made by virtue of reagent's selective inhibiting, and the purpose of upgrading the raw material used for vanadium extraction with hydrometallurgical process is achieved. The process technology obtained from project study features simple process structure, low equipment investment, low cost of mineral processing and pollution-free to environment. It provides high efficient and practical technology for the comprehensive utilisation of clay vanadium mineral, and has a prominent prospect for its popularisation and application.

Sep 13, 2010

Detailed investigation was carried out on the dephosphorization of a number of phosphorus-rich manganese or samples of India by leaching with dilute sulphuric acid. Various process parameters like concentration of acid, liquid-solid ratio, temperature of leaching, time of leaching, and particle size of the ore were studied in detail for the three samples of manganese ore from central India, and optimum values were worked out on a laboratory scale. Preliminary studies show that certain ores which are not easily amemlible to appreciable dephosphorization by leaching with dilute sulphuric acid can be made amenable by :roasting to 700-900°C before leaching.

Jan 1, 1974

Mr Kapp's paper helps considerably to clarify the subsidence/mine geometry relationships in New South Wales. It is in the best tradition of the presentation of field investigations such as has built up internationalknowledge over the years.The Author has plotted in Fig. 10, the maximum subsidence developed over each of a number of panels of different width/depth ratios and concludes that the maximum possible subsidence over a super critical extractionarea is around 0.65 of the mining height and that this is reached with the critical width/depth ratio of extraction of around 1.5.Although, as Mr. Kapp says, the maximum possible subsidence in the UK can reach 90% of the seam thickness extracted the more usual figure for the first seam is up to 80%. It has also been found in the UK that with shallow workings such as those at Kemiro Coliery the critical width of extraction is 2.0 or more times the depth.

Jan 1, 1981

A new test coke oven of 7 cu. ft. capacity is described. The oven was designed to simulate conditions in a central section of a battery oven and a special feature is the achievement of unidirectional heating from theflues on either side of the charge.The method of charging permits close control of charge conditions such as bulk density and moisture content.These conditions, as well as coking conditions (e.g. flue temperatures and coking time) must be varied to simulate conditions in different batteries. The effects of several variables on coke quality are discussed.Using test oven conditions corresponding to those of Newcastle steelworks batteries, good agreement was obtained between strength indices of test oven and battery cokes. For 17 tests, the average ASTM stability and hardness indices for the test oven coke were 38· 5 per cent and 69·7 per cent, while those for the battery coke were 37· 4 per cent and 67·6 per cent.Observed relationships between coke yield and productivity, and volatile matter and charge moisture are given.The use of a test oven to classify test coals into prime-, medium-, poor-, and non-coking coals is discussed.This may be achieved by observing the effects of the test coal in blends with other coals. The results of a series of blending tests are presented.The dangers of attempting to predict coke quality from a single coal property are pointed out, since this can be done only for very restricted ranges of coals.A diagram is given showing the established trends in the effects of blending various types of Australian coals on coke strength.

Jan 1, 1970

By Baker G

The detailed mineral composition of the lead-zinc ores at Captain's Flat was first studied in 1942 (Edwards, 1943).At that time the workings did not extend far below the 750ft. level. Since then development has been extended to the 1,390ft. level, and -at the request of the management of Lake George Mines Ltd., an examination of the ore from the deeper levels has been made as part of the research programme of the Mineragraphic Section of the Commonwealth Scientific and Industrial Research Organization.This account is. based on that examination (Mineragraphic Rept. No. ,537, C.S.I.R.O.)GENERAL GEOLOGYThe geology of the Lake George Mines has been described briefly in The Geology of Australian Ore Deposits (1953), and in much greater detail in an unpublished report by K. Glasson (1952). The area consists of fossiliferous Upper Ordovician sediments overlain by volcanics (Kohinoor VoJcanics), and by fossiliferous Silurian sediments. The volcanies comprise a series of· flows ranging in' composition from dacite to rhyolite, with interbedded tuft's and shale lenses.The region has been strongly folded. The regional strike is from 340° to 355°, and dips are from 75°W. to 75°E, A major syncline, pitching 200 N., occupies the centre of the area. The Kohinoor Volcanic'l outcrop as two bands which represent the east and west limbs of this syncline.The Volcanks in the western limb, with whIch the orebodies are associated, are more strongly sheared than those in the eastern limb.

Jan 1, 1953

By F Gervilla, J Laukkanen

The Kevitsa Ni-Cu-PGE deposit in northern Finland contains disseminated Ni-Cu-Fe sulfides, and platinum-group minerals (PGM). The 2.05 Ga-old ultramafic-mafic, funnel-shaped intrusion is intruded into a volcanosedimentary sequence. The major ore minerals are pentlandite, hexagonal pyrrhotite and troilite, chalcopyrite, cubanite and magnetite. Pyrrhotite and pentlandite are replaced by pyrite, millerite and heazelwoodite near the surface. Nickeline, maucherite and gersdorffite are locally abundant. A pilot feed sample of 575 t of the main orebody at Kevitsa had average grades 0.45 per cent Cu, 0.36 per cent Ni, 1.85 per cent S, 0.33 g/t Pt, 0.34 g/t Pd and 0.19 g/t Au, with 0.06 per cent Ni contained in silicates. Higher PGE contents (2 - 27 ppm) occur in a vertical N-S bearing fault zone. The PGM (n = 6022) mapped in specimens of four drill holes, consist of sperrylite 34.7 vol per cent, braggite and cooperite 18.5 vol per cent, geversite 17.2 vol per cent, moncheite 14.7 vol per cent, merenskyite 6.7 vol per cent, stibiopalladinite 4.3 vol per cent, sobolevskite 1.9 vol per cent, kotulskite 0.7 vol per cent, michenerite 0.6 vol per cent, keithconnite 0.3 vol per cent, rustenburgite 0.1 vol per cent, melonite, froodite, laurite together 0.1 vol per cent and only a few grains of sudburyite, irarsite, vysotskite, erlichmanite, hongishiite, Pt-Cu-alloys, three undefined Pd and Pt bismuthinides and antimonides and a Pd-Cu-bearing Pt-Ni-Fe sulfide. Most of the PGM, 62 per cent, are enclosed in silicates, 29 per cent are intergrown with sulfides, nine per cent are within sulfides. A portion of the PGE occurs in solid solution in sulfides and arsenides. Ni flotation yielded smelter-grade concentrates averaging 12.2 per cent nickel. The average sulfide Ni recovery is 78.8 per cent and total Ni recovery is 65.3 per cent. The average Pt is 10 g/t at 55 per cent recovery, Pd 7.7 g/t at 38 per cent recovery and Au 1.6 g/t at ten per cent recovery. Cu concentrates averaged 28.6 per cent Cu with an average recovery of 78 per cent and further 11 per cent in the nickel concentrate. The copper concentrate contains 4 g/t Au at 24 per cent recovery. The average Fe to MgO ratio 17.9 is well above the targeted minimum of 4.5. The pilot results show that the previously used TETA (triethylene tetramine) can be avoided and good quality, smelter-grade concentrates can be produced from the Kevitsa ore at economical levels of recovery by conventional flotation methods.

Jan 1, 2008

A poured slag bottom is universally considered to be the best type bottom for copper reverberatory furnaces. It is impervious to molten matte and ready for immediate use.When molten slag is not available a monolithic silica bottom is the second best; such a bottom has been adopted at Mount Morgan. The laying of such a bottom is a phase of smelter construction on which so little real information is obtainable that a day to day record of such a recent example as Mt. Morgan's 19 ft. x 40 ft. reverberatory may be of interest. The work was done under the direction of E. Pesout, of McGill Smelter, Nevada. PREPARATION OF THE BOTTOMA 26-inch bed of closely packed firebrick with sand-filled joints was first laid on the clean, dry concrete foundation and the whole dried out by small fires maintained on the brickwork for several days. Ninety tons of silica sand was meantime thoroughly dried and stored in clean drums. This sand must be low in FeO and CaO and contain about 95% Si02 , the majority of which should be present as tridymite. This form of silica shows little expansion at high temperatures, for it is the form stable between 870° and 1470° C.Its presence thus minimises disturbance to the bottom by the expansion which, during the burning in, would mark the transformation of quartz to tridymite.

Jan 1, 1939

The maximum current density at which conventional copper electrowinning plants will result in satisfactory, adherent, and dendrite·free cathodes is determined by the thickness of the diffusion boundary layer. A decrease in the value of that thickness will permit an increase in the current density. This fact is utilized to develop a high current density cell in which the reduction of the boundary layer thickness is accomplished by means of a specially designed electrolyte circulation system. The high current density cell is used to determine the effect of current density on such process parameters as current efficiency, cell voltage, power consumption, and cathode purity. A number of empirical equations are developed for the purpose of estimating the magnitude of these effects.

Jan 1, 1972

Hatches Creek has been inactive since 1961, but with better metal prices, interest in the field is reviving.The mixed gravity concentrates which were unsalable in 1951 have been experimentally separated into salable wolfram, scheelite, and bismuth-gold concentrates, and a flow sheet incorporating magneticseparation and flotation has been developed.

Jan 1, 1965

By P Steinier

Most operations, when considering their comminution circuit, are primarily concerned with achieving the desired particle size distribution to obtain adequate liberation for the separation process, at minimum cost. Invariably, the effect the grinding media has on the subsequent separation process (ie flotation, leaching) is not taken into account when selecting the media. This choice is driven by cost rather than metallurgical outcomes. Maximising valuable mineral recovery, with optimum selectivity against gangue minerals, is about good particle preparation. And, particle preparation is strongly related to achieving adequate mineral liberation with the correct pulp chemical conditions. However, the pulp chemistry of a system is largely ignored and relies heavily on pH control and the addition of appropriate reagents (collectors, frothers, activators, depressants). The changes effected by the addition of the various reagents are obtained through conditioning the ground pulp prior to or during the concentration stage, subsequent to grinding. Frequently, reagents are added during grinding with good effect, but the impact of the grinding media on down stream processing is usually overlooked. A number of case studies examining the effect of grinding media on pulp chemistry and subsequent flotation performance were completed on several different sulfide mineral systems (for example, lead/zinc, copper, refractory gold). The evidence suggests that a change in grinding media type from forged to high chrome (ie conditioning the pulp during grinding) resulted in a shift in pulp Eh to less reducing conditions, an increase in the dissolved oxygen content of the pulp and a reduction in the iron species present. The changes have a positive impact on flotation behaviour. The results of the case studies are discussed.

Jan 1, 2004

Application of the Anaconda Simplified Work Index for Multiple Test Sizes Vale uses Bond Work Index measurements extensively in a number of applications. The Bond Work Index is usually a good parameter for checking scale up procedures when sizing ball mills, as well as the basis for variability analysis whenever drill core data is available. It is typical to measure between 100 and 150 Bond Work Indexes, depending on the deposit characteristics. The Bond procedure is relatively complex and time costly. It also requires relatively large amounts of sample, which are very expensive to be obtained. The benefits of the Anaconda simplified procedure are: considerably smaller sample requirements and laboratory time. This makes it very much attractive at Vale's development centre, including geometallurgical mapping, operation efficiency control, mine to mill, etc. The Anaconda simplified procedure was implemented and evaluated at Vale's Development Centre using a number of ores and several samples of each ore totalling more than 190 measurements. The Anaconda simplified method was calibrated for several test sieves and a correlation for any test size was determined for Vale's test mill. The calibration was also extended for two sample top sizes. The relative error of the simplified procedure was found to be in the range of nine per cent which is within the expected error Bond standard procedure. The implementation of the Anaconda method at Vale's development center has been used with great success over the past years in several green field, brown field projects and operating plants.

Sep 13, 2010

The Calypso geothermal field, mapped by the R V Sonne (cruise SO-135) in 1998, includes four main sites, the Northern Vent Area (centred on 37¦ 36.7'S, 177¦ 06.2'E, area 1.5 km2), Central Vent Area (37¦ 39.4'S, 177¦ 05.2'E, 1 km2), Southern Vent Area (37¦ 41.7'S, 177¦ 06.0'E, 1 km2) and Mercury Vent Area (37¦ 41.3'S, 177¦ 07.3 'E, 0.5 km2). Hydrothermal activity at the vent sites is controlled by minor, sub-parallel NE-trending normal faults. Gas bubble trails (C02) and shimmering hot water vent from fractures and joints between large blocks of silicified volcaniclastics and in depressions in the sediments at the base of these outcrops. Measured maximum vent temperatures are between 180¦C and 201¦C. Venting fluids are at, or just below, boiling for water depths of 200 m. Rock samples recovered by dredge from the sites include massive anhydrite, clay-altered pumiceous ash, silicified volcaniclastic sediments and volcaniclastic breccias cemented by sulphur. Clay-altered samples, dominated by randomly interstratified illite-smectite and accessory chlorite, indicate formation environments of 70¦C to 90 ¦C. Native sulphur is abundant throughout the samples. Fine-grained (<1 mm) disseminated pyrite and vein pyrite occurs in the clay-altered pumiceous volcaniclastics and argillites. In the Southern and Mercury Vent Areas, fine-grained orpiment, realgar and cinnabar have deposited in the sandy matrix of volcaniclastic breccias. Amongst the cinnabar, small (<2 mm) beads of native Hg formed on the surface of several rocks following their recovery. These samples also contained abundant light hydrocarbons, which coat the rocks with an oily sheen.

Jan 1, 1999

For small particles of niekel flotation eoncentrate (av. size 50 pm) the predominant heat transfer mechanism under suspension smelting conditions, prior to ignition, is conduction from the gas and not radiation from nearby hot bodies. Results of laboratory tests using gas temperatures 380-700°C and furnace wall temperatures 380-1100°C were in accord with heat transfer theory. In practieal flash smelters earlier ignition, and hence better utilization of the space in the shaft, would result from introduetion at the top of the shaft of gases hotter than the ignition temperature of 500-600°C.

Jan 1, 1979

Recently published extensions to the mill-dump cutoff grade theory for joint open pit-concentrator operations lead to equations that must be simultaneously satisfied as a necessary condition for an optimal operating policy. These equations are parametrically dependent upon ore quality parameters, other than grade, relating to the ease of recovery of the disseminated mineral in the concentrator. Since it is not possible to treat quantities of ore corresponding to the size of selective mining units separately in the concentrator some mixing is inevitable and often deemed desirable in the interest of homogeneity of mill feed. This renders the calculation of cutoff grades for individual mining units futile; mining units must be grouped to form larger parcels that can be dealt with separately. In doing so an opportunity cost may be incurred; the loss of potential benefit that would result from such separate treatment. This matter is considered from a theoretical, qualitative, point of view. A numerical example then shows that a significant variability in the quality parameters can be tolerated without incurring such opportunity cost, provided sufficient knowledge is available concerning the distribution and effect of these variables to enable the use of effective mean values of these parameters in the cutoff grade calculation. Lack of such knowledge can have major consequences for the economics of the operation.

Jan 1, 1981

After a snap-shot survey of water quality of streams draining various coal measures carried out in 2000 - 2001, West Coast Regional Council expanded its monitoring programme to better establish the condition of streams draining coal mining areas and to characterise the variability of water quality with respect to stream flow. Samples were collected for water quality indicators such as pH, sulphate, turbidity, conductivity, temperature and dissolved oxygen as well as macro-invertebrates, fish and assessments of stream habitat. Water quality sampling was carried out at 27 sites on 21 streams located from Page Stream near Seddonville in the north, to Seven Mile Creek near Dunollie in the South, and to Garvey Creek east of Reefton. There was relatively low variability of pH, conductivity and sulphate concentrations at most of the sites sampled. Conductivity and sulphate concentrations reduced with increasing flow and pH generally increased. Significant effects on macro-invertebrate and fish populations were identified at several of the sites where water quality sampling was undertaken. Of the water quality parameters tested, macro-invertebrates were mostly affected by pH. Although not sampled directly (conductivity was used as a surrogate) heavy metal concentration may explain some of the variation in macro-invertebrate communities. Three creeks affected by mine drainage were sampled for fish and no fish were present. Fish appear to be more sensitive to acid rock drainage that invertebrates. Using data from this survey and other studies conducted in the region, the total length of stream that is actually or highly likely to be adversely affected by acid rock drainage was estimated at 125 km. This figure is useful as a gauge as to the magnitude of the issue in this region and for setting of priorities for remediation. However, as it is only an estimate based on limited sampling sites, it should be used with caution.

Jan 1, 2003