Search Documents

By C. D. Demond

In reverberatory smelting, fuel is the chief item of expense, as it commonly is in processes using large percentages of it. Hence the most suitable supply is eagerly sought; that is, the supply which, in the end, yields the greatest net profit. The better grades are not infrequently bought, even at an advanced price, because they are apt to be decidedly more economical. High price, of itself, however, is no merit, for freight is generally the largest part of the cost of fuel, and the nearby supply may yield as high efficiency as that from a greater distance. If a poorer grade is reasonably good, and if its cost is low enough to more than offset the decreased technical efficiency, it is of course the more suitable. Any smelting operation depends for both efficiency and economy on raising the furnace atmosphere considerably above the "critical" temperature; that is, above the temperature at which smelting is completed. If this temperature is not exceeded, smelting stops, no matter how much coal is burned; and the real value of a fuel depends on the number of degrees that the temperature is continuously kept above this point. For example, if one fuel maintains 2,500" F. and another only 2,100 F., while the "critical" temperature is 2,000" F., the first is worth at least five times as much as the second, although the increase above atmospheric temperature is only one-fifth more in one case than in the other. This "margin of temperature" above the smelting point is much more significant than the total number of heat units developed from the fuel. The case is parallel to that of water flowing from a pipe. The reservoir may contain a billion gallons of water; but, even though the fluid has come to the nozzle, not a drop will run out, where it can be of practical use, unless the level in the reservoir is higher than the nozzle; and the speed and volume of flow depend on how much higher the level is in the reservoir than at this point. If the temperature in a furnace is not above the critical level there will be no slag to flow over the skimming plate, even though there are enough heat units to bring an unlimited quantity of charge up to the point of slag formation; and just as the value of a water supply for the purpose of putting out a fire depends largely on the effective head, so the difficulties of furnace management

Jan 1, 1915

By R. Schuhmann Jr., P. J. Ensio

As a first step in a study of the physical chemistry of copper-smelting slags, experimental measurements were made of the oxygen pressure of simple iron-silicate slags in equilibrium with solid iron. The experiments consisted in bubbling CO2-CO mixtures through the slags in iron crucibles and in finding the equilibrium ratios of CO2 to CO. From the data, activities and partial molal heats of solution FeO and SiO2 in the slags were calculated. THE ternary system FeO-Fe,O,-SiO, is the simplest system which can represent adequately the important chemical properties of the slags formed in matte smelting and converting. Accordingly, the experimental study of slags in this system was started as the first step in a general research program on the thermodynamics of copper smelting. A recent paper by one of the authors' outlines this general research program and shows in some detail how information on thermodynamic properties of iron-silicate slags, especially information on oxygen activities, is essential to a full understanding of the chemistry of copper smelting. The FeO-Fe,O,-SiO, system also is the basis of slags produced in other processes, such as acid steelmak-ing processes, and is important in relation to the behavior of silicious refractories. In addition, data on the physicochemical properties of iron-silicate slags should contribute to a general understanding of the nature of slags, since at present such data for all kinds of slags are relatively meager. The principal quantitative information already available on iron-silicate slags consists in Bowen and Schairer's constitution diagram for slags in equilibrium with metallic iron,' Darken and Gurry's complete and precise thermodynamic study of the Fe-0 system,",' and Darken's study of the phase equilibria in the Fe-Si-o system. From the results of this previous work, it was clear that a complete thermodynamic study of ternary iron-silicate melts was a major undertaking which would have to be broken down into parts, including the working out of the ternary equilibrium diagram as well as extensive activity measurements on slags. The experimental measurement of oxygen activity, using CO-CO, and other gas mixtures as yardsticks of oxygen activity, was the basis of Darken and Gurry's study of the Fe-0 system. From the experimental measurements of oxygen activities over a large range of temperatures and compositions, they were able to calculate the activities of other species such as Fe, FeO, Fe,O,, etc., and also the other important thermodynamic properties in the Fe-0 system. At the start of the present investigation, it appeared that the same approach would be fruitful for the study of iron-silicate melts. Also, the experimental measurement of oxygen activities seemed particularly attractive because oxygen activity itself is a quantitative measure of oxidizing or reducing power, which is an important variable in copper-smelting slags. The slag compositions in equilibrium with yFe appeared most suitable for the first investigation of this kind, for the following reasons: 1—Good constitution data2 were available. 2—An iron crucible could be used, thus affording a simple solution to the refractory problem without introducing contarnination. 3—With Fe activity fixed, at unity with respect to a standard state of solid Fe, measurements of 0 activity could be followed by simple calculations of activities of FeO and other Fe-0 complexes and of SiO,. 4—This starting point afforded several possibilities for cross-checking with previous work,

Jan 1, 1952

Jan 1, 1929

By Robert B. Hoy

If the reader finds that the basic information in a commodity chapter is insufficient, he can consult the appropriate sources in this chapter to find more detailed or more up-to-date information. In these days, technology develops so rapidly that this 5th edition will be somewhat out of date even by the time it is distributed. A comparison of this edition with the 4th edition (1975) of Industrial Minerals and Rocks will clearly demonstate how rapidly the scene changes. One of the best sources of new information, of course, is attendance at technical meetings. For example, the papers presented at the national and sectional meetings of AIME usually discuss new developments in the respective divisions of the society. Frequently this information is available in Preprints. In addition some are printed in Mining Engineering and/or the Transactions of the Society of Mining Engineers of AIME. Furthermore, other professional and trade journals contain articles pertinent to the field. A journal introduced in 1967, Industrial Minerals, published by the Metal Bulletin, Ltd., London, is an excellent source of information. The Mining Journal, Ltd., also in London, publishes a weekly journal, a Mining Magazine (monthly), and a Mining Annual Review. The latter covers the field from three aspects: (1) by commodities, (2) through technical developments, and (3) geographically. The Industrial Minerals Directory 1977, 1st ed., Metal Bulletin Books, Ltd., London, provides addresses of organizations in the field. Other useful magazines and periodicals include Engineering and Mining Journal, Pit and Quarry, Rock Products, and World Mining, all published in the United States. In addition many new books related to industrial minerals have been published since the 4th edition of Industrial Minerals and Rocks. Most of these are included in the bibliography of each chapter in this volume. Another excellent information source is the proceedings of the Forum on Geology of Industrial Minerals. This group, which held its 18th annual meeting in 1982, is sponsored by a state geological survey or another mineral agency on a rotational basis. The proceedings have been published by the various sponsors and are available as indicated in Table 1. Two major sources of basic industrial mineral and rock data in the United States, and also a good source for many foreign countries, are the US Geological Survey and the US Bureau of Mines. The two agencies publish many reports and maps on a variety of geological and mining subjects. In addition, each agency has an indexed list of all their publications with a free service announcing new publications: New Publications of the Geological Survey, US Geological Survey, 329 National Center, Reston, VA 22092 and New Publications-Bureau of Mines, Publications Distribution Branch, US Bureau of Mines, 4800 Forbes Ave., Pittsburgh, PA 15213. The US Bureau of Mines (USBM) publishes annually Minerals Yearbooks which provide statistical data on mineral products including production, consumption, imports and exports, as well as information on new developments. Another very useful USBM series is called Mineral Facts and Problems. Editions were published in 1960, 1965, 1970, and 1975. Four major series of publications by the Bureau are Information Circulars, Reports of Investigations, Mineral Trade Notes, and Minerals and Materials. The last two are particularly good for news of foreign developments. The Bureau of Mines Employee Directory, available at all USBM offices, lists addresses and telephone numbers for all offices as well as same for all commodity and area specialists.

Jan 1, 1983

By H. L. Brunjes, G. B. Gould

The softening temperature of coal ash, as determined in the laboratory, has been used for years as an indication of the tendency of coal to form clinker and slag. It has not, however, provided an index of unfailing and complete reliability for forecasting the relative performance of different coals, even in the same plant and under the same conditions of operation. A large amount of investigation has been done in attempts to account for this, but practically all of this has been in the direction of studying the chemical constitution of coal ash. Much has been learned, but without much progress toward a better practical application of knowledge to the selection of coal. There has always seemed to be an important factor that eluded discovery. It has long been recognized that the ash-softening temperature as determined in the laboratory had one weakness, in that it represented the temperature at which a thorough mixture of the whole ash of the coal would melt, the mixing having taken place before the heal was applied. This does not, of course, simulate what takes place in practice. With certain exceptions, which will be noted later, almost all of the investigations that have been made, especially the chemical studies of coal ash, have likewise dealt with a mixture of the whole ash in the coal. The present investigation differs from these fundamentally in its approach to the problem. It started from the observation that some clinkering and slagging obviously takes place in a boiler furnace at temperatures below the laboratory-determined ash-softening temperature of the coal. Knowing that coal as it is shipped to market is a heterogeneous mixture of diverse mineral substances, each of which may act independently of the others in the initial stages of clinker and slag formation, it seemed logical to investigate separately the softening temperature of the ash in physically separable portions of the coal, and to determine the relative quantities of ash contributed by each portion. While the data are far from complete, covering as they do only a few coals, and while the conclusions to be reached from the data at this stage arc, in some measure, speculative, they are presented at this time because

Jan 1, 1940

By G. B. Gould, H. L. Brunjes

The softening temperature of coal ash, as determined in the laboratory, has been used for years as an indication of the tendency of coal to form clinker and slag. It has not, however, provided an index of unfailing and complete reliability for forecasting the relative performance of different coals, even in the same plant and under the same conditions of operation. A large amount of investigation has been done in attempts to account for this, but practically all of this has been in the direction of studying the chemical constitution of coal ash. Much has been learned, but without much progress toward a better practical application of knowledge to the selection of coal. There has always seemed to be an important factor that eluded discovery. It has long been recognized that the ash-softening temperature as determined in the laboratory had one weakness, in that it represented the temperature at which a thorough mixture of the whole ash of the coal would melt, the mixing having taken place before the heal was applied. This does not, of course, simulate what takes place in practice. With certain exceptions, which will be noted later, almost all of the investigations that have been made, especially the chemical studies of coal ash, have likewise dealt with a mixture of the whole ash in the coal. The present investigation differs from these fundamentally in its approach to the problem. It started from the observation that some clinkering and slagging obviously takes place in a boiler furnace at temperatures below the laboratory-determined ash-softening temperature of the coal. Knowing that coal as it is shipped to market is a heterogeneous mixture of diverse mineral substances, each of which may act independently of the others in the initial stages of clinker and slag formation, it seemed logical to investigate separately the softening temperature of the ash in physically separable portions of the coal, and to determine the relative quantities of ash contributed by each portion. While the data are far from complete, covering as they do only a few coals, and while the conclusions to be reached from the data at this stage arc, in some measure, speculative, they are presented at this time because

Jan 1, 1940

By Sidney Powers

CONTENTS PAGE Distribution of fields 4 History of development 6 Origin of oil 7 Structure,, accumulation and migration 8 Reservoir rocks 9 Methods of drilling and exploration to Oil-field statistics 12 Description by regions: United States: Appalachian region 12 East-central states 17 Kansas 18 Oklahoma 19 Texas 24 Arkansas 32 Louisiana 33 Mississippi -.. 34 Rocky Mountain region 34 California : 37 Canada 41 Mexico 43 Cuba 46 Bibliography 46 THE purpose of this brief account of the occurrence of petroleum in North America is to make available to those who have a knowledge of geology, but who are not engaged in the petroleum industry, a few salient facts about the location of oil and gas fields, their productivity, the important structural types of accumulation and the age of the rocks containing petroleum. A few useful data and statistics are furnished, yet not complete statistics that are available elsewhere. Geology has been treated in simple terms because the reader is presumed to have little interest in the names of formations and of oil sands. Mineral deposits are more or less analogous. Whether oil or metals, minerals are found in rocks, largely in sedimentary rocks which carry water or have at one time carried it. A genetic or accumula-

Jan 1, 1931

By E. G. Schempp, W. A. Morgan

The influence of modifications in the molybdenum, vanadium and, to a limited degree, carbon and boron content to a basic composition of 5 pct Cr, 0.75 pct Mo, 1 pct V hot-work tool steel composition, was studied in respect to hardenability, grpain- coarsening temperature, and tempering charactevistics. Tensile, impact, and fatigue pvoperties were studied for the most promising compositions. An alloy with a typical composition of 0.43 pct C, 4.97 pct CI-, 0.33 pct Si, 2.25 pct Mo, and 1.00 pct V uas found to offer the most favorable combination of properties in respect to high-strength applicntions when tempered at 1100°F. MANY 5 pct Cr high-strength steels are at present being manufactured in North America which fit well into the classification of the AISI-SAE system. Much interest has been shown in these materials as ultra-high-strength steels for use at elevated temperatures. The limiting temperature of use lies at the point where the steels begin to soften rapidly. Although a great deal of information has been made available in the past two years on the properties of selected alloys in this series, little information exists on the effect of systematically varying the ccntent of one or more elements in the 5 pct Cr-base alloy. This paper presents the results of an investigation of the effect of variations of the carbon, molybdenum, vanadium, and, to a limited extent, the silicon, manganese, boron, and niobium content of a 5 pct Cr steel to the AISI H-13 base analysis. EXPERIMENTAL PROCEDURE All experimental heats were melted in a 50-lb. induction furnace. The melting stock consisted of

Jan 1, 1962

By J. R. Kyte, L. A. Rapoport, R. J. Stanclift, S. C. Stephan

Experimental studies covering a wide range of core materials and fluid properties have been conducted to determine the mechanism of oil displacement by water in a partially gas-saturated porous medium. In all instances, the presence of a gas phase was found to have a beneficial effect in reducing residual oil saturations. The practical significance of this benefit is discussed, and a simplified procedure is outlined for evaluating the effects of free gas on water flooding by means of short core tests. INTRODUCTION In addition to oil and water, reservoirs subjected to water flooding frequently contain, also, a gas phase. Common engineering procedures account for the presence of this "free gas" only from the viewpoint of volumetric balance, implying that the only role of the gas consists of providing "fill up" space. It is usually visualized that during the initial stages of the water invasion, the oil, moving ahead of the water, displaces part of the gas and that subsequently the remaining portion of the gas phase is totally compressed and dissolved in the advancing oil bank. Thus, consideration of a two-phase, water-oil flooding mechanism supplies an adequate basis for predictions of oil recovery if the pressure build-up caused by the flood is sufficiently great, so as to reduce the free gas saturation to a negligible value in any portion of the reservoir by the time that portion is reached by the advancing flood water. In many in- stances, however, waterflooding operations are carried out when the reservoir pressure is still relatively high SO that the pressure build-up associated with the water flood may not result in complete dissipation of the gas phase. Under such circumstances it is necessary to ascertain whether or not the presence of free gas has an effect on waterflood behavior and, if so, to account for any such effect in the evaluation of field operations. The difficulties encountered in attempting to arrive at a comprehensive picture of the displacement mechanism of oil by water in the presence of free gas stem from the fact that most of the published data on this subject were obtained under conditions that were either not clearly representative of those existing in a reservoir or not sufficiently controlled to permit evaluation of the effects specifically caused by the gas phase. Some of the most precise data found in the literature were obtained in tests using a "static" gas phase created prior to each water flood by circulating oil through partly gas-saturated cores until a "trapped," residual gas saturation was established throughout the system.' Other investigations were conducted under more representative conditions where the gas phase was free to move during the water flood: but in most cases the results of these tests were obscured by auxiliary phenomena which arise from the compressibility and solubility of the gas and preclude quantitative conclusions.2,3,4 Prior to water flooding, a reservoir usually contains oil and gas, distributed in a manner in which both are free to move. Thus, the principal objective of the present studies was to determine the type of displacement mechanism occurring when water invades a porous medium containing oil and a "mobile" gas phase. Further-

Jan 1, 1957

By V. N. Krivobok

THE study and use of low-carbon manganese steels have been curiously neglected in the general history of developments in alloy steels. Hadfield1 made an extensive study of manganese-iron-carbon alloys about 1886, which culminated in the wide application and use of Hadfield austenitic manganese steel. His alloys were nearly all high in carbon, as compared with the steels discussed in this paper, and he found a marked tendency towards brittleness in the alloys of medium and low manganese content, that is, below 7 per cent. manganese. As a result, there has been a widespread prejudice against the use of manganese steels containing between 1.0 to 3.5 per cent. manganese with comparatively low carbon. Steels of this composition have never been studied adequately in comparison with other alloy steels, and have had little use in practice. In a very recent paper by Sir Robert Hadfield2 the following statement appears: ?. . . manganese-iron alloys with little or no carbon do not seem to offer any practical employment; they only become valuable in the presence of quite high percentages of carbon, 0.90 to 1.50 per cent." The results of the present investigation are so contrary to the findings of Hadfield that the writers feel fully justified in presenting the preliminary report incorporated in this paper.

Jan 1, 1927

By Yap Chu-Phay

IN 1923, when the writer began his studies in metallurgy, he came upon an article by Professor Honda on the, Equilibrium Diagram of the Iron-carbon System, 1 which made a profound impression on him. What interested him most was this sentence: "In the recent diagram of the iron-carbon system, the solidus is usually shown as a curve bending considerably downward. But it can be shown by thermodynamics that if the liquidus is straight or slightly curved, the same must also be true for the solidus. Hence, in my constitutional diagram, the lower portion of the solidus is slightly bent upward." Ever since then the writer has been interested in thermodynamics, especially chemical thermodynamics. The applications of thermo-dynamics to the metallic systems have been, in the writer's opinion, sadly neglected, although we continually use the phase rule in our study of equilibria in the liquid and solid states of metallic alloys. Many investigators, among whom may be mentioned Heycock and Neville, and s Honda and his coworkers, have applied the simple Raoult-van't Hoff law of depression of freezing point, mainly to determine the heat of fusion, but no attempt has been made to investigate the applicability of the thermo-dynamic laws of solution (as opposed to the laws of solution derived from other sources) to metallic systems" showing either limited or complete solid solutions. Perhaps the reason for this neglect is that until recently there have been so few reliable data on the solidus, which is much more difficult to determine than the liquidus. The writer has under way at the present time an investigation of a number of systems, the solidi of which have been more or less reliably determined. Recently, the writer has not only shown the valid applicability of the thermodynamic laws of solution as applied to the system antimony-bismuth but has also suggested a method of attacking problems involving complete and incomplete equilibria.2 In the present paper, the same method of approach is employed. For convenience, we shall divide this paper into two parts:

Jan 1, 1931

By G. Pizzi, G. M. Ciucci, G. L. Chierici

The use of the material balance equation to estimate the volume of hydrocarbons originally present in a reservoir, whose producing mechanism is partly due to water drive, has been discussed in the literature by several authors. There is no general agreement upon the possibility of obtaining reliable results by this method. Gas reservoirs in contact with an active aquifer are considered in this paper. Theoretical considerations based on the cybernetic principle of uncertainty (which states that the internal structure of a system cannot be uniquely determined from its observed external behavior) lead to the conclusion that the volume of gas originally present in a reservoir of this type cannot be uniquely determined from its past history. The range of values which encompasses the actual value of the reserves varies from case to case and must be determined by either numerical or analogical methods. Results obtained for six gas fields are reported. All these fields were produced with small fluctuations in their production rates, as is common practice for gas reservoirs; no gas storage fields were considered. Results obtained show that reserves values in a range of 1 to 2, associated with appropriate aquifers, allow the matching of the reservoir past history with mean-square deviations less than the experimental errors involved in pressure and produclion measurements. Similar results have been found in several other partial water drive gas reservoirs. From these results it is concluded that gas reserves cannot be uniquely determined from the past performance of partial water drive reservoirs, at least in cases where the reservoir has been submitted to small fluctuations in the production rates, and pressure data of normal accuracy are available. INTRODUCTION A number of authors have analyzed the problem of estimating the reserves originally present in a partial water drive reservoir from its past pressure-production performance. Literature which deals with this subject can be grouped, according to their conclusions, as follows. 1. A reliable value for the reserves can be obtained even if reservoir data (pressure and cumulative production) are affected by errors within the normal range.'-' 2. A reliable value for the reserves can be obtained only if reservoir data are very accurate'- or if past production performance has been subjected to abrupt variations in the production rate."' 3. No unique value for the reserves can be obtained from reservoir past production performance. This conclusion has been based upon theoretical considerations" and verified in several field cases. The purpose of this paper, which deals only with partial water drive gas reservoirs, is to test the above conclusions against actual field cases. Some theoretical considerations on this problem are also presented. THEORETICAL CONSIDERATIONS As the behavior of a gas reservoir communicating with an aquifer depends on both the aquifer and the reservoir characteristics, the physical system to be studied is the combined gas reservoir plus aquifer. The information which is available for studying the performance of such a system is the well production rates and bottom-hole pressures, all given as functions of time. The external behavior of the reservoir-aquifer system is therefore described by 2n input variables (Gp, Wp,) and n output variables (p,), n being the number of wells in the reservoir. In reservoir engineering it is common practice to consider the reservoir as a whole, disregarding the internal distribution of pressures and of producing wells. This practice is equivalent to substituting the above multi-variable system with a single-variable system, where the average reservoir pressure is the only output variable and the cumulative production G,(t) and W,(t) are the input variables. The internal structure of such a system, defined by initial gas reserves G, aquifer shape and dimensions, boundary conditions and petrophysical parameters distribution throughout the aquifer, is unknown. Therefore, from a cybernetic point of view the system is a "black-box It has been demonstrated" that for a blackbox the indetermination principle holds. Accordingly, the number of different internal structures (or set of parameters) which can account for the observed external behavior is infinite. As a consequence, the initial reserves cannot be uniquely determined from the reservoir past performance. When W,(t) is known, the determination of G from

By J. J. Forbes

THE Federal Coal Mine Safety Act (Public Law 552, 82nd Congress) was approved on July 16, 1952. It incorporates, as Title I, the Coal Mine Inspection and Investigation Act of May 7, 1941 (Public Law 49, 77th Congress), which gave Federal inspectors only the right to enter coal mines for inspection and investigation purposes but no power to require compliance with their recommendations. Title II contains the enforcement provisions of the act; its purpose is to prevent major disasters in coal mines from explosions, fires, inundations, and man-trip or man-hoist accidents. At this point a brief account of events that pre- ceded the enactment of the Federal Coal Mine Safety Act seems appropriate. The hazardous nature of coal mining was recognized by the Federal Government as long ago as 1865, when a bill to create a Federal Mining Bureau was introduced in Congress. Little was done, however, until a series of appalling coal- mine disasters during the first decade of this century provoked a demand for Federal action. As a result an act of Congress established a Bureau of Mines in the Department of the Interior on July 1, 1910. The act made it clear that one of the foremost activities of the Bureau should be to improve health and safety in the mineral industries. One of the first projects selected by the small force of engineers and technicians then employed was to determine the causes of coal-mine explosions and the means to prevent them. By investigations after mine disasters the fundamental causes and means of prevention were soon discovered, and the coal mining industry was informed accordingly. However, despite this knowledge and the enactment of State laws and the Federal Coal Mine Inspection and Investigation Act of 1941, mine disasters continued to occur with disheartening frequency and staggering loss of life. The devastating explosion at the Orient No. 2 mine on December 21, 1951, resulted in the death of 119 men. The Orient disaster rekindled the memory of the Centralia, I11., disaster of March 25, 1947, which caused the death of 111 coal miners. These two tragedies ultimately brought about enactment of the Federal Coal Mine Safety Act.

Jan 1, 1954

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By H. A. Schwartz, W. Kenneth Bock

In this paper it is shown that when the tensile strength of a given steel in various states of heat-treatment is plotted against its elongation, a straight line results. The equation of this straight line can be computed with considerable accuracy from its chemical composition. The appropriate equations are given. The logarithm of the slope of the tensile-strength locus is shown to be proportional to the cumulative effect of the total alloy addition and the vosition of the line to be directly proportional to the cumulative effect of the alloy content. It is further pointed out that heat-treatment is more effective than composition in determining yield ratio. The latter enters mainly by its effect on hardenability, which is briefly discussed. Reduction of area and Brinell number are given some incidental attention. The data are applicable only to steels that have been normalized and/or quenched. The steels, if normalized, may or may not have been tempered. If quenched they must have been tempered at or above 4oo°C. (75o°F.). Introduction Cast steels vary in composition and frequently are used in various states of heat-treatment. It is obviously important to be able to predict the compositions that might accompany specific engineering properties by suitable selection of heat-treatments. For cast steels, which are of necessity produced heat by heat in accordance with the particular requirements of the castings to be poured, there has been, happily, much less tendency to standardization than for rolled products, whose destination is not necessarily known when particular ingots are made or rolled. It is of distinct advantage to the steel foundry-men to be able to make steel of given properties, using alloys that can be recovered from scrap, or most conveniently or cheaply bought, rather than a particular formula adopted in the interest of standardization. The heat-treatment appropriate to securing a given result in a given steel is well known to be closely related to composition. For example, molybdenum steels are not much softened by tempering except at rather high temperatures. Highly alloyed steels are "air-hardening," and on cooling in air behave like carbon steels that have been quenched. With these matters, we do not concern ourselves in this paper, although we recognize their importance. The entire picture evidently will be very complex and can be brought within accurate understanding only if our knowledge of test results can be coordinated in terms of general principles.

Jan 1, 1944

By H. L. Stone, A. O. Garder

A numerical method of solving the partial differential equations which describe the one-dimensional displacement of oil by gas has been presented. Possible extension of the method to treat multidimensional flow is discussed, and the limitations of this extension are indicated. Using this method, it is possible to allow for the existence of a gas cap, the presence of any number of gas-injection or oil-production wells and the evolution of dissolved gas from the oil. It is also possible to allow for variation in the cross-sectional area, elevation, porosity and permeability of the reservoir. The influence of relative permeability and the force of gravity in the direction of flow upon the displacement is considered. The influence of capillary pressure upon the flow and the effect of gravity in the direction perpendicular to flow are neglected. The physical properties 01 the fluids are considered to be Junctions of pressure only, and equilibrium between contiguous phases is assumed. The numerical calculations can be readily carried out by the use of a digital computer. Several example analyses have been performed using the IBM 704 computer, and about one-third of an hour of computing time was required per case. Reservoir behavior predicted by use of this numerical method was compared to data obtained by other methods for three cases — complete pressure maintenance, dissolved-gas drive and gas-cap drive. The independent solutions to these problems were obtained by analytical solution, laboratory experiment and field data, respectively. Agreement of the numerical solution with data from these sources was good; this agreement establishes the convergence and accuracy of the numerical method. INTRODUCTION Most petroleum reservoirs can be produced by any one of several alternative programs. When a reservoir is produced by primary methods, production economics can be influenced by controlling the number and location of wells and the flow rate of each well. An even greater influence may be achieved by augmenting the recovery of oil obtainable by primary methods. This can be accomplished by injection of fluids such as water, natural or enriched gas or a bank of light liquid hydrocarbons. Selection of the most desirable operation requires a means of predicting the reservoir behavior which will result from each of the several alternative programs. The purpose of this paper is to present a mathematical method for predicting the behavior of reservoirs produced by gas-cap drive, dissolved-gas drive or pressure maintenance by gas injection. The method described herein takes cognizance of phase changes caused by a decline or an increase (due to gas injection) in reservoir pressure, of the presence of a gas cap and of the effect of gravity on the flow of gas and oil. Relative permeability relationships are used to define the flow properties of the rock. Allowance is made for variation in cross-sectional area, elevation, permeability and porosity of the reservoir. Both the influence of capillary pressure upon the flow and pressure gradients in the gas cap are neglected. Whenever a liquid phase and a gas phase are in contact, they are assumed to be in equilibrium. The physical properties of the fluids are considered to be functions of pressure only. Therefore, if the method is to be used to predict the effects of a gas-injection program, mixtures of the injected gas and formation crude should-have the same physical properties as mixtures of formation gas and crude. The equations to be presented in this paper apply only to a one-dimensional case; therefore, they neglect the influence of gravity in the direction transverse to the flow. As is well known, this gravitational influence may lead to overriding of oil by gas. Consequently, this procedure as presented is most applicable to long, thin reservoirs for which gravity overriding is not important. On the other hand, the equations presented can be generalized to treat multidimensional flow and, hence, to consider gravity overriding, if desired. A word of caution on two points is advisable here, however. First, the authors have not demonstrated the accuracy of the numerical technique for multidimensional flow. Second, and more important, capillary pressure will often be of importance in multidimensional problems. Obviously, in such cases a generalization of the

Map

Jan 1, 1938

By R. J. Wygal

A method is presented by which homogeneous, isotropic, and reproducible aggregates of particles such as glass beads, sand, ground glass, etc., may be prepared simply and quickly by using a "particle distributor". Several applications of the packing method to the construction of model reservoirs are described. The flow characteristics of these packings me given. Some factors which limit the usefulness of unconsolidated packs for simulating reservoir rock are overcome through artificial cementation of the aggregates. INTRODUCTION Many laboratory studies of porous media are based on experiments using test packs of sand, glass beads and other granular materials. More confidence can be had in the results of such studies if the test packs are known to have uniform properties throughout, to be mechanically stable and to be accurately reproducible. This paper presents a method by which such packs of a variety of shapes and sizes may be constructed using a particle distributor. Some factors which limit the usefulness of unconsolidated packs as a means for simulating reservoir rock are described. A method of overcoming these limitations, which involves artificial cementation of the packs, is presented. DEVELOPMENT Particles packed by the tamping or vibrating techniques are usually either non-uniform or mechanically unstable. An invention by Currie and Gregoryl overcomes these difficulties to some extent. The invention is based on the use of a stream of falling particles impinging on and passing through a distributor matrix of several layers of closely spaced spheres. The particles are well dispersed by numerous collisions with the spheres. They become homogeneously distributed at some distance below the distributor matrix and at that position are collected in the sample container. This apparatus, however, was found to be ineffective when small particles were used since small particles accumulate on the top surfaces of the spheres. An improved distributor matrix was made, first in the form of a stack of five sieves, and then in the more adaptable form of spaced layers of wire screen. Fig. 1 shows a longitudinal view through a five-layered distributor of eight-mesh wire screen. This device gives excellent results.* Fine particles pass through the distributor with very little hold up. The fine structure of the wire matrix with its many deflecting surfaces ensures good particle distribution. There are no dead areas immediately below the screen as were sometimes observed to occur below a matrix of spheres. Using such a device, 20-30 mesh sands were packed to a porosity of 32.1 per cent at rates varying from 0.17 to 6 lb/rnin. The lowest porosity achieved by tamping small increments of similar sands into a container was 33 per cent. Motion pictures at 3,000 frarnes/sec of the surface of a growing pack of 2-3/4 mm glass beads have helped to show the mechanism by which packs of low porosity are obtained. The beads, although packed at the rate of 5 lb/min, were observed to hit the pack surface singly, for the most part, and at well spaced points of impact. Part of their energy is transferred to surface beads which are thereby

By L. D. Jaffe, R. K. Pitler

IT would clearly be advantageous to produce molten titanium, suitable for alloying and casting, directly from the relatively inexpensive tetra-chloride, without using a metallic reducing agent. Accordingly, a preliminary investigation has been made of the production of titanium by hydrogen reduction of the tetrachloride in an electric arc furnace. For the reaction: TiCl4(g) + 2H2(g) ? Ti(s) + 4HCl(g), Lockhart and his colleagues' have calculated equilibrium constants at 800" to 1500°K, based on tables of Brewer.' Extrapolating these data on the assumption that the heat of reaction varies linearly with temperature, and using Brewer's value for the heat of fusion, there is obtained for the reaction: TiCl4(g) + 2H2(g) ? Ti(l) + 4HCl(g) an equilibrium constant at 2100°K (100" above the melting point) Kp = (PHCl)4/pTlcl4 (Ph2)2 = 0.167 atm. If this is correct, starting with hydrogen saturated with TiC14 at 25°C, where the vapor pressure of the latter3 is 12.6 mm, and maintaining the overall pressure at 1 atm, 99 1/4 pct of the TiC14 would be reduced to Ti at equilibrium. An arc furnace designed for the melting of titanium and lined with water-cooled copper was used for the preliminary experimental check. Its inside diameter was 2 7/16 in. and height 6 in. The water-cooled electrode was tipped with 3/4 in. diam tung-sten. In the one run carried out, the furnace was charged with a starting batch of 293.35 g of scrap titanium,' analyzing 99.24 pct Ti. After the system was twice pumped out and flushed with argon to remove air, the arc was struck in argon and kept at 400 amp dc, electrode negative, for 1 min to melt the starting batch. Commercial tank hydrogen, dried by passing over silica gel and bubbled through technical grade TiC14 at room temperature, was then admitted to the furnace. The inlet tube directed this gas downward toward the arc and melt; the gas outlet was at the top of the furnace. The quantity of gas passed through was not measured accurately but is estimated to be about 50 liters per min at a few mm of mercury above atmospheric pressure. The arc was held in the H2-TiC14 mixture at 400 amp with little difficulty. After 10 min the arc burned through the copper lining above the melt, admitting water and ending the run. (This had happened frequently in straight melting runs under argon, and is not thought due to the atmosphere used.) In the furnace were found an ingot, several small pieces, and a little metallic powder, evidently formed when water entered the hot furnace. Some titanium also clung to the electrode. The portions were weighed and separately analyzed for titanium. Their total weight was 321.76 g of 94.82 pct overall purity. Much of the impurity consisted of tungsten broken off when the titanium was removed from the electrode. No detailed impurity analysis was made because the starting materials were impure and flooding the furnace introduced further contamination. Thus, the metal recovered contained 305.08 g Ti, as compared to 291.12 g in the starting batch. Titanium could not have been carried over from previous melting runs in the furnace, as the interior was sandblasted and the electrode ground clean before the run. Evidently at least 13.96 g of Ti were produced from TiCl4. Since this would require complete reduction of 430 liters of TiCl, gas at 12.6 mm of Hg, the efficiency of the process must have been rather high. Experimental work is continuing. No reason is seen why the process could not be scaled up to the size of a 30-ton steel-melting arc furnace. In a large unit there would be a large molten pool from which liquid metal could be withdrawn for alloying and casting. The problems of electrodes and power supply are similar to those arising in arc furnaces for melting titanium. Unreacted TiC14 and the HC1 in the exhaust gases could be recovered; unreacted H2 could be dried and re-used. The melt would be saturated with hydrogen, whose solubility in liquid titanium is unknown. Small amounts of hydrogen seem to have little effect on the properties of titanium.5 If the amount introduced was so large as to impair properties or cause casting difficulties, it could be reduced by holding the melt under an inert gas or by pumping on it, prior to casting. Acknowledgment The authors would like to thank I. Preble and M. Goldman for their valuable aid in the experimental work and the thermodynamic calculations, respectively. References 1R. J. Lockhart, J. J. Ward, M. J. Hussey, and J. W. Clegg: In unpublished report, "U. S. Air Force Project Rand. Titanium and Titanium Base Alloys." Battelle Memorial Institute (1949) 37-44. 2 L. Brewer et al: Chemistry and Metallurgy of Miscellaneous Materials—Thermodynamics. Ed. by L. L. Quill. pp 13-39, 60-192. (1950). McGraw-Hill Book Co. 3 K. Arii: Scientific Reports. Tohoku Imp. Univ. (1933) 22, 182. 4 R. S. Dean, J. R. Long, F. S. Wartman, and E. L. Anderson: Transactions AIME (1946) 166, 369-381; Metals Technology (Feb. 1946) TP 1961E. * R. I. Jaffee and I. E. Campbell: Transactions AIME (1949) 185, 646-654; Journal of Metals (Sept. 1949) TP 26813.

Jan 1, 1951

By W. L. Fink, H. C. Stumpf, L. A. Willey

VERY few studies of the aluminum-sodium system have been reported. Heycock and Neville1 were unable to detect any solubility of sodium in liquid aluminum. Mathewson2 prepared an equilibrium diagram consisting of two horizontal lines at the melting points of the two metals. He was unable to detect solubility at either end of the system. Scheuer3 first developed a method for the chemical determination of sodium in aluminum and then studied the solubility of sodium in liquid aluminum. His method involved heating aluminum with excess sodium under hydrogen until the two liquids were at equilibrium, chilling the melt, and analyzing the aluminum-rich layer. He reported the solubility to be 0.l0 pct sodium at 700°C, 0.115 pct at 750°C, and 0.128 pct at 800°C. This paper on the aluminum-sodium system is the twenty-first in a series from the Aluminum Research Laboratories describing equilibrium relations in aluminum alloy systems. MATERIALS The alloys for this investigation were prepared from electrolytically refined aluminum (99.99 pct) and sodium of reagent quality conforming to specifications of the American Chemical Society.4 Chemical analysis of the aluminum showed the following impurities: 0.002 pct Si, 0.002 pct Fe, 0.002 pct Cu, <0.001 pct Mn, 0.002 pct Mg and 0.001 pct Na. The sodium content of all alloys was determined by either chemical or spectrographic standard procedures5 No. IIA and No. SII respectively. DETERMINATION OF LIQUIDUS The boundary of the miscibility gap was determined by a modification of the method of Scheuer3 and of that used by Henry and Cordiano.6 As finally developed the method was as follows: A fused alumina crucible 25 mm id with 75 mm depth and 1.5 mm wall thickness was placed on the bottom of a container made from a 4-in. length of 1 ½ -in. iron pipe and pipe caps. The space around the sides of the crucible was filled with 40 mesh crystalline alundum. A charge of 60 g of aluminum and 10 to 15 g of sodium was placed in the crucible, the sodium first being trimmed and rinsed with iso-pentane to remove kerosene. The container was tightly capped, filled with argon (99.6 pct pure), and heated to the desired temperature (between 670 and 800°C). A positive pressure of argon (about 8 mm of mercury) was maintained through a small pipe to the upper cap. After soaking for from 2 to 5 hr, the container was quenched by directing a stream of water onto the base, so that solidification of the aluminum-rich layer was rapid and essentially unidirectional. Analyses were made on drillings taken from the bottom of the ingots after machining off the surface layers. Pre-

Jan 1, 1948