Search Documents

By R. Simon

The sources of energy dissipation for concentrated loadings on rock are considered in an attempt to account for the experimentally measured magnitude of the work required to break out a unit volume of rock from the free surface of an essentially semi-infinite medium. It is concluded that most of this work probably represents the elastic strain energy developed by the loading in a much larger volume of rock beneath the loaded region than the volume of the rock fragment broken out to the side of the loaded region. This strain energy is largely dissipated in the form of stress waves generated by the high rate of unloading produced by the propagating cracks. The energies associated with the formation of the new surfaces of the cracks and with the stress waves generated directly by the loading process are computed to be negligibly small. Possibilities for improving the utilization of energy to drill rod. subject to the geometrical limitations imposed by down-hole operation, are discussed. It is pointed out that any such possible improvements would probably have to be differential ones, since each rock configuration of more favorabIe loading geometry that can be created down the hole is accompanied by a complementary configuration of less favorable loading geometry. INTRODUCTION Dislodging each cubic inch of rock from the bottom of the hole by the action of a bit requires the expenditure of an amount of energy that varies from approximately 5,000 in.-lb to approximately 100,000 in.-lb, depending on the hardness of the rock, or, more technically, upon its fragmentation strength.1 In this paper we will discuss (I) why the energy expended in drilling is so large, (2) what happens to this energy upon completion of the drilling process, and (3) what are the possibilities for reducing the magnitude of the energy required to drill rock. DETERMINATION OF ROCK DRILLING ENERGY The volume of rock removed per unit time from the bottom of a hole of diameter D is evidently (7/4)D2R, where R is the rate of penetration of the bit. If P is the rate at which work is done by the bit on the rock at the bottom of the hole, the energy required to break out a unit volume of rock is given by: Ev =(4/p) P/D2R............(i) For rotary drilling, of either the rolling-cone or drag-bit varicty, P = 2pLN, where L is the torque resistance to rotation at the bottom of the hole and N is the rate of rotation of the bit. L is essentially the same as the torque measured at the rotary table only when drilling in shallow holes. The energies expended in rotating the drill string against the frictional resistance of the walls of the hole and and against the viscous drag of the drilling fluid are extraneous to the subject under consideration, although these may be much greater in magnitude than E, when drilling in a deep hole. For percussion drilling, P = fE where f is the percussion frequency and E is the work done on the rock per impact. The latter quantity can be both computed and measured for a percussion drilling machine. 2 (Under satisfactory drilling conditions, defined in terms of ranges of numerical values of certain dimensionless parameters, E is only 30 to 50 per cent less than the impact energy of the striker.2) Alternatively, E, may be measured directly by dropping chisels shaped like bit edges, backed by rigid weights, onto the surfaces of laboratory rock samples of effectively semi-infinite extent. Under these circumstances, essentially all of the impact energy is converted to work done on the rock, and the relationships among volume of rock broken out, chisel shape, impact energy and indexing distances can be obtained.3 The values of the energy required to break out a unit volume of rock under favorable circumstances are substantially in agreement for rotary drilling, percussion drilling and drop testing at atmospheric pressure. The energy per unit volume is a quantity of the order of magnitude of roughly twice the com-pressive strength of the rock as measured by a uniaxial loading test. The phrase "order of magnitude" in this paper means from about 1/3 as much to 3 times as much; i.e., the energy per unit volume may range from roughly the same up to several times

By W. L. Zeigler

During the middle 1880's, shortly after the discovery of silver-lead ores in the Coeur d'Alene district of northern Idaho, it became apparent that concentration of the ores would be necessary to obtain a profitable product. Too much siliceous material was present for direct smelting, and the majority of the ores found at depth were too low in metallic content for economic smelting processes at the time. As the ores occurred in quartzite shear zones with siderite and quartz gangue, a large quantity of waste material was present in all the mines. As the galena was not finely disseminated, this made possible relatively good extraction of the argentiferous galena by coarse concentration. The first concentrators consisted mainly of coarse crushing, screening and jigging, principally by Harz jigs, the slimes being treated on buddles. Later Wilfley tables took the place of sand jigs and vanners superseded the buddles. Because of the marketing conditions, no attempt was made until 1900 to effect a recovery on the zinc minerals present, which were found associated in varying amounts with the galena. All through this period, the greater part of the production was obtained from mines containing ore assaying high in lead and low in zinc. Parts of some ore bodies would be reversed in this respect, so that ores high in zinc were left intact. During the decade after 1910, several important mines, The Success and The Interstate Callahan, containing ores high in zinc, were put into operation and were a material aid in the needed zinc production during World War I. Gravity concentration by jigs and tables was used during this period, with bulk flotation increasing in popularity for the treatment of the fine material that had already been treated by ordinary slime concentrating machinery. No extra fine grinding for flotation concentration was thought profitable at the time. Tailings Discharged into Streams From the start of mining and milling operations in this district until 1904, no attempt was made by the various mills in the upper district to impound or stack their tailings. They discharged them directly into the adjacent creeks or streams, to be carried away by high water. The Bunker Hill and Sullivan and the Last Chance mines, both in the relatively flat valley of the district, stacked huge piles of the coarse jig tailings on the near-by river bottom. Rain and snowfall are heavy in the Coeur d'Alene district, as it is on the heavily timbered Pacific slope of the Bitter Root Mountains. A heavy runoff occurs every spring and there is an occasional flood of disastrous proportions when warm "Chinook" winds accompanied by rain

Jan 1, 1949

By Research Staff ? Verde Copper Mines

FLOTATION is now commonly practiced in alkaline ore pulps, yet little is known regarding the action of the alkaline solutions on the ore particles beyond the fact that films of oxidized material form. We wish to chronicle our discovery of the presence of soluble reducing agents in alkaline ore pulps of the United Verde, and present some data on lime consumption. During the grinding and flotation of a pyritic ore containing small amounts of ferrous sulfate and other soluble salts, an excess of lime was added to precipitate the salts, and filtered samples of the solution were titrated with standard permanganate solution. Even in pulps of high causticity an appreciable permanganate titration was always obtained, in spite of the fact that the solutions were shown to contain little iron. Investigation of the cause brought about the discovery of several previously unsuspected compounds in flotation pulps made from pyritic ore. Not only the reducing agents present had to be identified, but also the amount of dissolved oxygen, and a survey was finally made of the free oxygen content and reducing agents of the mill pulp in the concentrating mill at Clarkdale. A great many. compounds might form, caused by oxidation of pyrite or other metal sulfides or by reaction between a lime solution and pyrite. The most probable compounds considered were calcium sulfides, polysulfides, thiosulfates, and polythionates. Later it was discovered in the literature that in alkaline pulp polythionates do not exist and if introduced are decomposed into sulfites and thiosulfates.1 Any precipitated sulfur is changed by alkali into thiosulfate and polysulfide. Sulfites and sulfides react to form thiosulfate, so that in the end it is possible to have in an alkaline solution only thiosulfate and an excess either of sulfide or sulfite. Confirmatory tests were made and it was finally established that the alkaline mill pulps made from the United Verde ore contained

Jan 1, 1929

THE RELATION OF THE ENGINEER TO RECONSTRUCTION FIFTY-THIRD MEETING OF BOSTON SECTION The fifty-third meeting of the. Boston Section was held April 28. The speaker of the evening was the new president of the Institute, Mr. Howard V. Winchell, who spoke on "The Relation of the Engineer to Reconstruction." He told of the part engineers had played in the war and paid tribute to Herbert E. Hoover as an example of what engineers can do. He said that engineers are not taking enough interest in politics, although it is badly needed as shown by the evidences of Bolshevism even in America. Conditions have suddenly changed; whereas we formerly borrowed money we are now loaning widely to foreign countries and our investments, abroad have to be protected. A committee is badly needed to investigate and determine the actual conditions. The Government has already been invited to cooperate with the Institute along professional lines and this should lead to closer contact between our Society and the Government. Mr. Winchell then went on to describe some of the mining conditions in Russia. He brought out the point that the rich platinum deposits are exhausted and only the poorer sands remain. The largest copper properties average less than 2 per cent. copper and there are some 4,000,000 tons available in .the Caucasus region near Batum. There are approximately 100,000,000 tons of high-grade manganese ore scattered in small deposits in the eastern Ukraine. There are some copper mines in the East, butt they are almost exhausted. The Baku oil field is the second largest in the world and there is probably oil in Persia. There are also manganese in Siberia and coal veins of enormous thickness.

Jan 7, 1919

By C. V. Millikan, C. V. Sidwell

There is nothing more important in petroleum engineering than a definite knowledge of the pressure at the bottom of an oil well at any existing operating condition, and the relation of this pressure to the pressure within the producing formation. A knowledge of bottom-hole pressures is fundamental in determining the most efficient methods of recovery and the most efficient lifting procedure, yet there is less information about these pressures than about any other part of the general problem of producing oil. Determination of Bottom-hole Pressures Bottom-hole pressure may be calculated or determined by several methods. On an inactive well it may be calculated from the fluid head or, if the well is shut in, by adding the casinghead pressure, the static head of the gas and the fluid head. In wells flowing naturally through tubing the pressure at the bottom of the tubing may be calculated by adding the pressure at the casinghead between the tubing and the casing and the pressure due to the weight of the column of gas, but there is always possibility of error caused by fluid being in the annular space above the bottom of the tubing. If a well with tubing is flowing through either the annular space or the tubing, sufficient gas may be injected through the static space to insure that it is free of fluid but not sufficient to establish an appreciable friction loss. The pressure at the bottom of the tubing can then be calculated by adding to the pressure at the tubing head the pressure due to the weight of the column of gas. This is probably the most accurate method of calculating bottom-hole pressures. In wells flowing by gas-lift, the pressure at the point the gas enters the flow may be calculated by a gas-flow formula. Several types of pressure bombs have been used to measure the pressure at the bottom of wells. One is a piece of steel tubing with a check valve in the bottom and a connection for a pressure gage at the top. It is lowered into the well to the point at which the pressure is

Jan 1, 1931

By Arthur C. Spencer

IN extension of a suggestion already made to account for certain features observed in the Juneau gold-belt in southeastern Alaska,' it is the object of the present paper to indicate in detail certain conditions in which deformation of rocks under their own weight might lead to the production of fractures in which veins could be deposited. A direct, uniformly-distributed pressure of sufficient intensity applied to an elastic brittle mass offering strong resistance to deformation produces rupture. In a material of ideal properties the surfaces of rupture under such pressure would be shearing planes inclined at 45° to the line of force, unless there be preliminary deformation, in which case this angle would be greater than 45°. This general conclusion, resting upon ana¬lytical mechanics, is completely supported by the results obtained by Daubrée in experiments upon the deformation of wax and resin prisms under compression. Let us then first con¬sider one of Daubrée's diagrams. In the case illustrated in Fig. 1, four sets of fractures in two appproximately right-angled pairs (that is to say, in conjugate sets) were produced by end-wise compression of the square cross-sectioned prisms. These fractures cut the axis of compression at approximately equal angles, not varying greatly from 45°. The location of the four sets of fractures is obviously determined by the shape of the prism, since the material in each corner acts in a way as a buttress, permitting the bulging to take place most readily on the sides. By limiting the directions in which bulging may take place, results of a more simple nature could be obtained. Take, for instance, a square prism and place it between two fixed and

Nov 1, 1905

By M. J. Pool, with Appendix by Larry Kaufman, R. W. Krenzer

Thermodynmic properties of the Cu-Mn system have been deterrrzined in the temperature range 973" to 1273°K by measuring the vapor pressure of manganese in equilibrium with alloys of compositions varying from 0.13 to 0.91 rnole fraction manganese using the Knudsen effusion technique. Activities of manganese calculated from the measured vapor pressures show large positive deviations. Calculated heats and entropies of mixing are positive with a maximum occurring at approximately 0. 7 mole fraction manganese. ThE investigation of thermodynamic properties of binary systems involving transition metals is of considerable interest at the present time. The incomplete subvalency electron levels of transition metals lead to unusual behavior in some alloys, and considerable information can be obtained by determining the thermodynamic characteristics of these systems and relating the thermodynamic behavior to observed physical properties. The Cu-Mn system, shown in Fig. 1,' provides an example of an alloy system in which the determination of the equilibrium phase diagram and various physical properties has received considerable attention, but very little work has been done on measurement of the thermodynamic properties. Elemental copper and manganese have comparable electronegatives, atomic sizes, and cohesive energies, but differ in crystal structure. They form a continuous series of solid solutions only at high temperatures and the structure varies in a continuous manner from fcc at the copper-rich end to fct at the manganese-rich end.' The purpose of this investigation was to measure the vapor pressure of manganese over a series of Cu-Mn alloys and from these values determine the thermodynamic properties of the binary system. Vapor pressure measurements were made in the temperature range 973" to 1273"K, remaining within the solid-solution region for each alloy studied. EXPERIMENTAL PROCEDURE The relative thermodynamic properties of solid Cu-Mn alloys were determined from vapor pressure measurements by means of the Knudsen effusion tech- nique. Several discussions of the theory can be found in the literature. In the case of copper and manganese, it is assumed that manganese is the only component subliming, so the vapor pressure of manganese over the various alloys can be determined directly by measuring the weight loss of the effusion cell. This is a valid assumption since the vapor pressure of manganese is about four orders of magnitude higher than the vapor pressure of copper in the temperature region of interest. The vapor pressure of manganese over the alloys at any given temperature is then related to the weight loss of the effusion cell per unit area per unit time. An upper limit of 1.5 x 10"s has been measured for the ratio of polyatomic to monoatomic molecules for manganese vapor in equilibrium with solid manganese at 1180°K, so it was assumed that manganese vapor is monoatomic. The effusion cells, fabricated from high-purity alumina, are 26 mm high, 18 mm OD, and have a wall thickness of 1 mm. Three different sized holes of 2.03, 2.54, and 3.18 mm diam were drilled in the lids from the inside face to minimize chipping, and the lids were then slip-cast onto the cells to provide a gas-tight seal. Alumina was selected for this particular application both because of its resistance to thermal shock and reaction with manganese vapor. In the ideal case, the orifice of the effusion cell should have a knife edge so that effusion through the orifice

Jan 1, 1970

By B. Yarar, J. Kaoma

[Introduction The critical surface tension of wetting of hydrophobic materials has been investigated extensively by Zisman et al. (1973) and relates the spreading of a liquid on a solid to the surface tension of this liquid. Thus, the Zisman ap¬proach shows that a plot of Cos 0 versus ?LV where, 0 is the contact angle and ?LV is the surface tension of that liquid in contact with its own vapor at equilibrium, produces a straight line which can be extrapolated to Cos 0 = 1. The intercept corresponds to a given ?LV, termed the critical surface tension of wetting. In instances, however, Cos 0 - ?LV plots show deviations from linearity. Alternative approaches have also included the plotting of adhesion tension (YLV COs 0) versus ?LV that can be interpreted in terms of critical surface tension data (Lucassen-Reynders, 1963). It has, on the other hand, been customary to correlate contact angle (0) with flotation data, although it is recognized that surface inhomogeneities and related contact angle hysteresis limit the interpretations pertaining to solid surface structures purely based on contact angle measurements. It is nonetheless true that 0 = 0, when the liquid is water, corresponds to a hydrophilic solid. Determination of ?c by contact angle measurements in conformity with the Zisman approach can encounter experimental difficulties, especially when solids are in a powder form. Following the reasoning that 0 = 0 corresponds to the hydrophilic state of a solid, froth flotation experiments can be expected to produce critical surface tension of wetting values for powders. The technique that consists of plotting recovery (% R) versus YLV data and extrapolating the linear part of the curve to % R = 0, has been described elsewhere (Yarar and Kaoma, 1984). This paper describes some of the results obtained by the extrapolation technique mentioned above, using various sulfide minerals. Experimental Materials Molybdenite (MoS2), sphalerite (ZnS), chalcopyrite (CuFeS2), chalcocite (Cu2S), and galena (PbS) were handsorted from massive samples and ground by mortar and pestle, and the -147 Fan fraction used in experiments; sulfur (S) was a C.P. Fisher Scientific Co. product. Method One gram powder samples were conditioned for three minutes in methanol-water solutions of predetermined surface tension values and the percents recovered by flotation using a Partridge-Smith Cell (Partridge and Smith, 1972), were plotted against each ?LV value. Results and Discussion The percent recovery versus ?LV for two naturally hydrophobic solids, i.e., natural molybdenite, MoS2 and sulfur are given in Fig. 1 where it is seen that ?c for sulfur is obtained as 31.5 mNm-1 whereas for MoS2, it is 26 mNm-1. Figure 1 also shows that the new flotation technique described, for estimating ?c is in good agreement with the Zisman method. Curves obtained by the same method for the minerals Cu2S, PbS, and ZnS are given in Fig. 2, where it is seen that for Cu2S, ZnS, and PbS, the extrapolation to % R = 0 produces ?c values of 36, 39, and 49 mNm-1, respectively. CuFeS2, on the other hand, gives a curve that does not permit such an extrapolation to obtain a ?c value with certainty. Nonetheless, treatment of the powder with 8.95 X 10-5 molar Na2S solution followed by washing with distilled water prior to flotation effects the curves as shown in the insert of Fig. 2. The type of curves given in Fig. 1 appear to be typical of hydrophobic solids as can also be observed in Fig. 3. The composition of solid and minute quantities of inclusions seem to play an important role as regards the surface properties of solids as reflected by the slope of the linear part of the % R - ?LV plot and thus the value of ?c obtained by this technique. For example, MoS2 of three different stoichiometric compositions produced the data given below. [MoS2MoS2.14Mo1.002S2 ?c mNm-126.029.031.0 dR/d?8.95.23.0]]

Jan 1, 1985

By Richard W. Smith

Kyanite, long known to occur in Georgia, did not excite coimmercial interest until about 1930. Investigation1 revealed two main types of deposits: (1) separate kyanite crystals embedded in mica schist; and (2) crystal aggregates of kyanite associated with quartz in small and very irregular veins. The second kind at first sight appeared to be the best source of supply. Large boulders or dornicks of kyanite with more or less quartz were found on the surface at many places throughout the Piedmont and Highland sections of the state, but prospecting failed to disclose a sizable vein. These dornicks seem to be a surface accumulation from small veins or lens-shaped masses not more than one or two feet thick, and with a horizontal extent of not more than a few feet. 'rile larger surface accumulation of kyanite dornicks, where not too badly stained by iron oxide, may prove to be marketable, but it is extremely doubtful whether a vein large enough to mine will ever be found. In 1932 deposits of the kyanite-mica schist were known to occur in two places northwest of Clarkesville, in Habersharn County. In 1934, at the request of and in cooperation with the Georgia Geological Survey, the United States Geological Survey made a thorough investigation2 of the deposits and found that the two known areas of kyanite-mica schist in Habershain County were but a part of an unsymmetrical, U-shaped belt (Fig. 1) with a western limb extending into Rabun County and somewhat longer than the eastern limb. The total length of the belt is about 30 miles. The width of outcrop ranges from 100 ft. to 1/4 mile or more. Deposits of kyanite-mica schist of very doubtful commercial importance were found in several other counties. Only the deposits of this kyanitc-mica schist belt in Habersham and Rabun counties will bc discussed in this paper. Geology The kyanite-mica schist of Habersham and Rabun counties occurs near the northern cdge of the Piedmont Upland in metamorphic rocks of pre-Cambrian age3. These rocks probably were deposited as sedimentary

Jan 1, 1938

By Richard W. Smith

Kyanite, long known to occur in Georgia, did not excite coimmercial interest until about 1930. Investigation1 revealed two main types of deposits: (1) separate kyanite crystals embedded in mica schist; and (2) crystal aggregates of kyanite associated with quartz in small and very irregular veins. The second kind at first sight appeared to be the best source of supply. Large boulders or dornicks of kyanite with more or less quartz were found on the surface at many places throughout the Piedmont and Highland sections of the state, but prospecting failed to disclose a sizable vein. These dornicks seem to be a surface accumulation from small veins or lens-shaped masses not more than one or two feet thick, and with a horizontal extent of not more than a few feet. 'rile larger surface accumulation of kyanite dornicks, where not too badly stained by iron oxide, may prove to be marketable, but it is extremely doubtful whether a vein large enough to mine will ever be found. In 1932 deposits of the kyanite-mica schist were known to occur in two places northwest of Clarkesville, in Habersharn County. In 1934, at the request of and in cooperation with the Georgia Geological Survey, the United States Geological Survey made a thorough investigation2 of the deposits and found that the two known areas of kyanite-mica schist in Habershain County were but a part of an unsymmetrical, U-shaped belt (Fig. 1) with a western limb extending into Rabun County and somewhat longer than the eastern limb. The total length of the belt is about 30 miles. The width of outcrop ranges from 100 ft. to 1/4 mile or more. Deposits of kyanite-mica schist of very doubtful commercial importance were found in several other counties. Only the deposits of this kyanitc-mica schist belt in Habersham and Rabun counties will bc discussed in this paper. Geology The kyanite-mica schist of Habersham and Rabun counties occurs near the northern cdge of the Piedmont Upland in metamorphic rocks of pre-Cambrian age3. These rocks probably were deposited as sedimentary

Jan 1, 1938

LATEST estimates of Russian steel production for 1951 give rise to the belief that on at least one vital front, the Western bloc of nations has maintained a definite advantage. On the surface, we are outproducing the Eastern bloc by more than twice. The United Nations Economic Commission for Europe estimates Russian output at 31.30 million tons, a 15 pct increase over the previous year. Production for the entire Iron Curtain is figured at 40.93 million tons. Western Europe alone produced 17 pct. more steel during the same period. The figures are misleading in one sense. We have no precise idea of how much steel is being used for arms. The Western nations are still expending much of their production for consumer goods, and you cant throw washing machines in a shooting war. It is significant to note that Russian production is well, beyond estimates made by world authorities prior to the current international situation. INTERIOR Secretary Oscar L. Chapman warns that the United States must make use of the resources of other nations or face mineral impoverishment once the time of struggle is over. He pointed out that the present struggle between two ideologies can leave the United States in such a state as to preclude anything but political' victory-with an accomp anying economic loss that will be irreparable. Chapman scored the attitude whereby conservation programs are looked upon as a luxury, pointing out that the nation faces an ever increasing need for action on that front. He also announced that the Bureau of Mines doubled its facilities for producing pure zirconium during 1950-51 at the request of the Atomic Energy Commission. Zirconium may be an important structural metal for atomic power devices. The Interior Secretary also said that the AEC has provided the Bureau with funds for the study of radioactive minerals and to help test and evaluate about 9000 ore samples believed to contain uranium.

Jan 1, 1952

By D. C. Jackling

I BESPEAK your indulgence for a brief expression of the views of a patriarch in the field of mineral industry technology relative to young men's problems in that sphere of education and endeavor. Wherever hereafter I employ the terms "technical education," "engineer," "technologist," or similar expressions, these are intended to be understood as relating to the broad field of the sciences and arts applicable to the mineral industries. First, the usefulness of technical education to either the possessor of it or those to whom its services may be made available industrially depends primarily upon the quality of the education and the capabilities of the educated to put his talents to effective and constructive employment in his chosen field of applied science.

Jan 1, 1940

By E. H. Sellards

ON Oct. 9, 1929, a sink formed in the Sour Lake salt dome oil field in Texas, and on Oct. 12 a second smaller sink formed at the north margin of the first. The purpose of this paper is to give such observations as it has been possible to make on the earth movement incident to this subsidence. Sour Lake salt dome is typical of the salt domes of the Gulf Coastal Plain of Texas. Structurally the dome is a plug of salt which rises to within 900 ft. or less of the surface. Above the salt is a cap rock consisting of anhydrite with more or less calcium carbonate. The salt plug, as contoured on the cap rock, is circular in outline with, however, some appreciable irregularities. Overlying the cap rock are relatively uncompacted sediments consisting of sand, clay and gumbo.. At the crest of the dome these deposits are no more than 700 or 800 ft. thick. However, the sides of the dome are steep, and the sediments thicken rapidly away from the crest. The sink formed about 1500 ft. northeast of the crest of the dome where the sediments overlying the cap rock are from 1000 to 1200 ft. thick. The cavity permitting the subsidence was quite certainly either in the cap rock or in the salt below the cap rock, so that the sink was formed by the caving of as much as 1000 or 1200 ft. of earth.

Jan 1, 1930

OIL FLOTATION DISCUSSED BY SOUTHERN CALIFORNIA SECTION . A meeting of the Section was held in the home of R. H. Norton, 335 W. 27th Street, on Mar. 10, thirty-two members and five guests being present. Vice-chairman Staunton opened the meeting with a description of an experiment he made with oil flotation, and then introduced the guest and speaker of the evening, L. C. Penhoel, of the South-western Engineering Co., who gave a very interesting and informal talk on the subject of Flotation. During the talk, as points were raised, there was a general discussion, in which valuable information was brought out. A number of examples of successful competitive, results by cyanidation and flotation in large milling plants in this country and Mexico were cited and discussed. The latter part of the meeting was devoted to a discussion of the bill introduced in the California State Senate, to license and register engineers. Mr. Ernest Strout gave a most favorable opinion of the principal of licensing mining engineers from his extensive experience in the working out of such a law on the Rand. All members who spoke were opposed to this bill as drafted but felt that the subject was of too great importance to the profession to attempt to amend the present bill in the week or two that remains, and that the passage of a bill that was so crude and inefficient for the achievement of the results desired, would harm the engineering profession. After the meeting adjourned a short time was spent in social intercourse, during which light refreshments were served. The appreciation and thanks of the Section is extended to Mr. and Mrs. R. H. Norton for their hospitality. ALVIN B. CARPENTER, Secretary-Treasurer.

Jan 5, 1919

BOSTON LOCAL SECTION Executive Committee HENRY L. SMYTH, Chairman ALFRED C. LANE, Vice-Chairman AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. ROBERT H. RICHARDS ALBERT SAUVEUR Meets on the first Monday evening of each winter month Twenty-fourth Meeting The Twenty-fourth meeting of the Boston Local Section was held at the Exeter Street Theater, Boston, Monday, Jan. 4, 1915. The Chairman, Henry L. Smyth, introduced Mr. S. Le Fevre, of Mineville, N. Y., who presented an exhibit of moving pictures, illustrating the various operations of mining and milling iron ore as carried out at Mineville. Mr. Le Fevre pointed out, as the pictures were run off, the dangers of the various operations, and the precautions that should be taken to avoid or minimize these dangers. . After the exhibition of pictures, the members adjourned to the University Club, where dinner was served. At the close of the dinner and an impromptu recital by Mr. Weeks, the meeting was adjourned. AUGUSTUS H. EUSTIS, Secretary.

Jan 2, 1915

SOUTHERN CALIFORNIA LOCAL SECTION Executive Committee THEODORE B. COMSTOCK, Chairman SEELEY W. MUDD, Vice-Chairman FREDERICK J. H. MERRILL, Secretary-Treasurer, 300 Germain Building, Los Angeles, Cal. C. COLCOCK JONES FRANK ROBBINS The February meeting of the Southern California Local Section-was held at the headquarters in the Chamber of Mines and Oil of. Los Angeles on Feb. 17, C. Colcock Jones presiding. Fourteen members were present. The subject announced was Ore Sampling. W. M. Watts opened the discussion by a general outline of the important points to be covered, in sampling a mine and the methods to be used in the various stages of the work. All the members present successively contributed details from their personal experience. The March meeting of the Section was held at its headquarters on Mar. 15. Twelve members were present, with Dr. Theodore B. Comstock in the Chair. The subject announced was Secondary Enrichment and all present took part in the discussion, Frank Robbins contributing a short paper on some observations in Central America. The next meeting will be held on Apr. 14, at which time the subject of Mine Accounting will be discussed. F. J., H. MERRILL, Secretary.

Jan 5, 1914

SAN FRANCISCO SECTION W. H. SHOCKLEY, Chairman, PRANK H. PROBERT, Vice-Chairman, T. A. RICHARD, Sec.-Treas., 420 Market St., San Francisco, Cal. C. C. BRAYTON, J. F. NEWSOM. The San Francisco Section met on September 11 to discuss the problem of Labor in its Relation to the Mining Engineer. Mr. W. H. Shockley was in the chair. T. A. Rickard opened the discussion under four heads: The recognition of the union, the rustling-card, the sliding scale of wages, and the' contract system. He expressed his belief that collective bargaining cannot be ignored, and insisted that the mining company represented a collective bargaining of its shareholders with the men. employed in its mine. He held that the contract system was often used unfairly, but that used fairly it was the best check on labor tyranny. The rustling-card he held to be right in principle, in so far as it gave the employer the choice of employees, but he believed that it was often used in an irritating way to black-list refractory laborers. The sliding scale of wages was easy to establish in prosperous times, but it would inevitably lead to trouble when conditions went against the miner. His conclusion was that the quarrels of labor and capital were due mainly to a lack of the sense of fair play and of social justice. Albert Burch agreed with most of the foregoing, and insisted that 90 per cent. of the men were inclined to be just, but that the 10 per cent: made all the trouble. He stated that he had introduced the rustling-card in the Coeur d'Alene in 1899, as a means for getting rid of agitators. E. L. Foucar considered that labor was irresponsible. He described his experience in Peru, where the authorities promptly stopped a strike of Italian miners by threatening prompt punishment for any display of violence. Morton Webber also gave a bit of his own experience, to show that the chief trouble is that the men do not think for themselves, and are therefore easily led by fomenters of trouble. F. H. Probert described his experiences in Germany and. also in Arizona, and insisted that too often the men were not given a fair hearing. E. T. Blake argued that a manager must get the workmen's point of view, in order to control them effectively. He believed that young men who started life doing manual labor were in a better position to understand their fellow workers. George J. Young suggested that the mine owners should encourage the good men to lead the unions, and not leave the direction of the unions to the noisy element.

Jan 12, 1917

BOSTON. SECTION W. E. C. EUSTIS, Chairman, H. L. AGASSIZ, Vice-Chairman., E. E. BUGBEE, Secretary-Treasurer, Mass. Inst. of Technology, Boston, Mass. ALBERT SAUVEUR, H. L. SMYTH. The 37th meeting of the Boston Section was held at the Engineers' Club, on Monday evening, Oct. 2, 1916. Fourteen members and guests attended the dinner. The Society was fortunate in having present not only the announced speaker, J. G. Carleton of Marblehead, Mass., but also a brother member from afar, Thomas Warner of California. Mr. Carleton, who has spent the' past few years in South America, gave an informal talk on the mining of the precious metals on the South American continent. He drew a comparison of the geographical distribution of the precious metals in North and South America and pointed, out the similarity in the geological occurrence of the eastern mining, regions, mentioning particularly Venezuela and Brazil. He also directed attention to the fact that the great placers of the northwestern part of North America had their counterpart in the gold-bearing region of Columbia. The marked contrast between the southern end of North America, so rich in metals, and the southern part of South America, so poor in mineral deposits, was clearly brought out. It is difficult to avoid the conclusion that the South American Cordillera is less intensely mineralized, than the corresponding mountain.

Jan 1, 1917

By G. Sachs

THE iron-rich iron-nickel alloys have at-tracted considerable academic interest in recent years. The carbon-free alloys are of minor practical importance, but they are Atomic per cent nickel FIG. I. FIG. 2. FIG, I.-HONDA'S AND MERICA's IRON-NICKEL DIAGRAM, FIG. 2.-MARSH'S IRON-NICKEL CONSTITU-TIONAL DIAGRAM. the base of many alloys with various out-standing properties. The iron-nickel alloys, therefore, have been investigated exten-sively regarding both their structures and their properties. The researches on these alloys up to 1938 have been collected and critically reviewed by J. S. Marsh,1 and will be discussed in some detail in the sec-tions of this paper dealing with specific subjects. These numerous investigations have not succeeded in establishing the equilibrium conditions in this system. Alloys containing more than a certain amount of nickel (8 to10 per cent Ni) undergo the allotropic transformation extremely sluggishly, both on heating and cooling, showing a large hysteresis,2 which is not dependent upon

Jan 1, 1940

NEW YORK SECTION J. E. Johnson, Jr., Chairman Edgar Rickard, Vice Chairman. D. M. Liddell, Secretary, 7 Wall St., New York, N.Y. C. A. Bohn, Treasurer John V. N. Dorr Lewis W. Francis. The annual meeting of the New York Section was held on Wednesday, June 6, with about 40 members in attendance. The treasurer re a brief summary of-the financial statement for the year, and the secretary's report was read. These reports were ordered placed on file together with the report of the auditors for the two previous years.

Jan 8, 1917