Search Documents

By Alberto Lainati

The Bar Reducing and Sizing Technology has a core function in the value-chain for the production of rolled SBQ (Special Bar Quality) products. The EVO 2+4-roll is based on the compact combination of a 2-roll high-reduction module followed by a 4- roll low-reduction module for precise sizing. The EVO 2+4-roll mill, allows to gain significant technical and economical advantages in the hot- and post-rolling process routes: dimensional and surface accuracy, quick adaptability to processing variances and to small lots requirements, superior technological features of as-rolled product, competitive capex and opex. The EVO 2+4 unit has a very compact design, which makes it suitable both for new mills and upgrade applications.

Aug 17, 2017

By Douglas Glenn Stalheim

Production of structural hot strip coils in yield strengths up to 700 MPa and higher is increasing worldwide. In addition to requiring higher strengths, structural designs require good formability, toughness and weldability. Toughness and formability come from optimization of ductility properties while weldability comes from lower carbon equivalent alloy designs. The key to the production of optimized cost effective hot strip produced structural coils is to create the correct balance of a proper alloy/processing design to create as fine and uniformly distributed cross sectional grain size as possible. In addition to the creation of the fine/uniformly distributed cross sectional grain size, the correct microstructure needs to be created. In the higher yield strength grades, not only does the grain size/distribution play a role but a proper understanding and control of microalloying precipitation kinetics is required. This paper will present various examples of hot strip alloy designs to produce cost effective hot strip structural coil in yield strengths up to 700 MPa with good ductility and weldability. In addition, steelmaking/casting parameters will be discussed to assure successful production. Optimized reheating, rolling and cooling parameters of these alloy designs will be introduced in an accompanying paper.

Aug 17, 2017

By Stefano Scubla

DANIELI Q-MELT is the latest evolution of EAF concept to automatically control each stage of the melting process, from the electric power planning to the combustion optimization as well as the slag and steel metallurgy management for every operation required in the EAF cycle. The core of the automation system is the Melt-Model that automatically identifies deviations of the process control variables and corrects them to avoid losses or wasting of available energy sources. The real-time online off-gas analysis, via the in-situ laser system, promotes the process tracking and permits further optimization by a viable closed-loop control acting on fuel and oxygen postcombustion. A suite of supplementary stand-alone Technological Packages integrates the Q-MELT to further maximize the productive time and the utilization factor, supporting the operators to limit downtimes, avoiding misoperations and/or mistakes.

Aug 16, 2017

By Thomas Schanz

Current steel market conditions require small investments only to lower operational cost. SMS Concast has developed new products which optimize continuous casting process cost for long product steel production. This paper describes a selection of three products. All three systems are patented (patent pending for CONDRIVE). CONSAFE, a non-radioactive mould level measurement system for reliable mould level measuring on open stream casting CCM’s; CONSTIR-MWS, an improved control software for electromagnetic stirrers which lowers energy cost by 35%; CONDRIVE, a brand new oscillation drive system which provides the features of a hydraulic oscillator, however with a cost efficient electric drive.

Aug 17, 2017

By Oliver Schulz

This paper presents the latest references of the Siemens VAI slab casting technology. Following the connect & cast philosophy Siemens VAI has developed technological packages suitable for installation in existing casters of any original supplier, as well as for complete new machines. A major demand on new machines is to adapt quickly to different market demands. This requirement for flexibility can be divided into two actual trends. Firstly into casting a broad range of steel grades, thicknesses and width on the same machine and secondly having installed slab, bloom and billet caster in one steel plant to deliver all different types of needs on the market. Depending on the condition of the existing machine the focus of modernization ranges from the substitution of single components featuring state-ofthe-art technology to complete caster revamping projects. In this paper concepts and references for short machine outages and fast caster ramp-ups at moderate investment costs are presented.

Jul 30, 2018

By Hugo Leandro Rosa

A CBMM aplicou aços micro ligados ao nióbio em dois tipos de caçambas de carregadeiras de rodas que operam na usina de Araxá, Brasil. O objetivo foi avaliar os benefícios destes aços relacionados com redução dos custos, aumento da produtividade e vida útil dos componentes. Uma das máquinas analisadas coleta peças quentes de ferro nióbio para carregamento dos silos do britador. O uso de um aço ferramenta de alta resistência e resistente ao desgaste solucionou os problemas de deformação, desgaste e rachaduras durante o serviço, aumentando a vida útil da caçamba em cerca de 190%. A outra máquina avaliada foi uma carregadeira de rodas que opera na mina de minério de nióbio. O novo desenho com aços de alta resistência mecânica e resistente ao desgaste reduziu o peso em 14%, correspondendo ao incremento na capacidade de carga. A carga extra possibilitou um aumento na produtividade dos caminhões de 42 toneladas. Com os novos materiais, as trincas anteriormente encontradas na caçamba da pá carregadeira foram eliminadas, enquanto foi mantida a resistência ao desgaste antes oferecida pelo aço revestido com carbeto de cromo reduzindo também os custos de investimento em 7%.

Aug 17, 2017

By Mário César Mantovani

The steel for gas turbine compressor discs (26NiCrMoV14.5) requires some mechanical properties like strength, impact, toughness, fatigue, and creep resistance in order to be used in such application. To achieve the properties required for the gas turbine compressor discs, the material should have very low contents of sulfur, phosphorus, antimony, tin and arsenic. The level of cleanliness should also be very high and this is possible by achieving low oxygen content keeping the deoxidation elements like silicon, manganese and even the aluminum in very low percentages. The main problem in refining such steel is to adjust a sufficiently low oxygen content to have a good desulfurization and at same time a good cleanliness without using silicon, manganese or aluminum as deoxidizers. Combination of initial selection material, steelmaking process control, forging sequence and heat treatment cycles can provide uniform mechanical properties throughout the gas turbine compressor discs. Villares Metals SA as a big player on special steels with complex process has been developing this kind of material for several years. The objective of this work is to show the process technology evolution involved in the production of this kind of steel under the discussed preconditions.

Aug 17, 2017

By Christoph Sedivy

Industrie 4.0 is slowly but surely arriving in the melt shops. Furnaces are being equipped with more and more sensors, digital models are increasing the degree of automation, and information is being shared between different aggregates within the plant. Because the electrode control system plays a key role in electric steelmaking, it naturally assumes an important position in the melt shop’s Industrie 4.0 strategy. In addition to reliable, state-of-the-art core regulation functionality, monitoring and reporting tools and the ability to communicate with other equipment are also required. Therefore, the latest generation of our electrode control system, the Melt Expert, was developed based on Industrie 4.0 design principles. Intelligent plant condition diagnostics, performance monitoring, and user-defined reporting are essential modules in this new system. With these functionalities, electrode control systems are developing into the information and control center of the furnace. A newly developed software app brings most relevant process information to mobile devices. This feature allows steelmakers to keep an eye on the performance of their equipment anytime and anywhere. This paper describes the new features of the electrode control system and shares our customers’ operational experience. Our focus is on the practical aspects of plant status monitoring, KPI reporting, and diagnostic functionality as well as the improvements achieved.

Oct 30, 2017

By Ivo Filipovic

The steel melting process in an Electric Arc Furnace is a complex set of tasks, coping with highly dangerous hazards as fire, explosions, uncontrolled reactions, hot metal projections and gas or dust emissions. Melt shops are dangerous working areas for operators, recording statistics with a high frequency of injuries. In the past years, without dedicated safety equipment, there wasn't a real attitude to the risk prevention. The paper describes the available technological packages to eliminate the manned activities on the melting floor, with the aim to prevent accidents and keep furnace operators safe. The technological packages suite extends the automatic control of the EAF melting process to all the operations from charging phase to tapping. Plus, the integration of the most frequent operations by automated specialized tools effectively minimizes power-off times, enhancing reliability and improving the transformation costs.

Aug 17, 2017

By Léo Daiki Shinomiya

O planejamento de cenários é uma ferramenta empregada como um mecanismo competitivo que entrega uma visão para um futuro passível de acontecer, baseado em fatos atuais e históricos. Adaptado para ser aplicado a resíduos industriais, este método de planejamento de cenários pode ser descrito em oito etapas. Neste trabalho é apresentada a 1ª etapa, que mostra o uso de pesos e critérios para definir as aplicações mais adequadas para a Lama Vermelha a partir de uma infraestrutura disponível localmente. A Lama Vermelha é gerada em larga escala pela indústria do Alumínio, somente no estado do Pará são gerados 5,4 milhões de toneladas anualmente, que impacta diretamente nos custos desta indústria em função de seu tratamento e estocagem. Os resultados guiam definições para as aplicações mais adequadas para a Lama vermelha, sendo destacado o emprego na fabricação de cerâmica vermelha e na produção do cimento.

Aug 17, 2017

By Constantino Capurro

For certain applications, coarse titanium nitride (TiN) precipitates can be deleterious for the final properties of the material. Hence, in order to better understand the mechanisms involved in the generation of these precipitates, a thorough characterization of the particles observed in steels with different titanium and nitrogen content was carried out. Samples from liquid steel (tundish), continuous casting billets and final product were evaluated using an Automatic Particle Analyzer (APA) coupled to a Scanning Electronic Microscope (SEM). The location, frequency, size distribution and composition of the different particles observed were assessed. While only few TiN precipitates were observed in liquid steel samples, the density of this type of particle significantly increased in the continuous casting billets samples. Particles ranging from 1 to 10 µm were mainly found in the interdendritic zones of the as-cast structure. The density of TiN particles observed in these samples did not change after re-heating and rolling operations. A model to predict TiN precipitation during solidification was developed. A reasonable agreement was found between model results and measured data. Results of this analysis confirmed that the precipitated fraction of TiN increases as the product of steel Ti and N contents rises.

Oct 30, 2017

By Pedro Augusto David Machado

The hot metal produced in small blast furnaces runs with a highly heterogeneous charcoal. The result is a significantly higher hot metal chemical composition variation, especially for the silicon content, which varies from 0.4 to 1.5% in Mini Blast Furnaces - MBFs, designed to feed an EAF and/or a BOF. These MBFs operate with frequent variation in their productivities to feed preferably only one of the steelmaking reactors, that is, EAF or BOF. The hot metal suitable amount, chemical composition and temperature, to be delivered at the steelmaking vessel, become the major concerns in the integrated operation MBF to EAF or BOF. In order to cope with those undesirable frequent variations, a solution has been proposed based on the existing technologies of oxygen jets and ladle refining techniques adapted to a hot metal ladle or to a Torpedo Car. The proposed technique is not only able to adjust hot metal temperature and chemical composition, but it also generates the adequate conditions for refinement from P and S, as well as “cleaning” hot metal ladles and Torpedo Cars by melting pig iron skulls. Therefore, this new technique development results in high hot metal yield, an adequate chemical composition and bigger campaign of hot metal ladle.

Aug 17, 2017

By Bernardo Martins Braga

O desgaseificador RH é um reator de refino secundário bem estabelecido. Nesse equipamento, gás inerte é usado para promover a circulação de aço entre a panela de aciaria e uma câmara de vácuo. A predição correta da dispersão de gás na perna de subida do RH é importante para a modelagem confiável do processo. O presente trabalho estudou a penetração de gás na perna de subida do RH por meio de modelos físico e matemático. No estudo, foram considerados apenas um ou dois bicos injetores e vazões de gás, por bico, entre 5l/min e 50l/min. Para as condições com um bico injetor, os resultados das duas abordagens mostraram boa concordância qualitativa. Já para as condições com dois bicos injetores, a concordância só foi satisfatória para vazões de até 30l/min por bico. Adicionalmente, os resultados obtidos indicaram que o problema de penetração de gás em modelos matemáticos de desgaseificador RH identificado na literatura está relacionado com erros numéricos e não com falhas na modelagem da física do problema.

Aug 17, 2017

By Douglas Valentim Fernandes Neves

O aço inoxidável austenítico 316 (316 SS) é um dos materiais metálicos mais utilizados em aplicações médicas devido à combinação de propriedades mecânicas e do baixo custo. No entanto, desgaste e corrosão estimulam mudanças permanentes no tecido humano que podem levar à perda do implante. O desenvolvimento de recobrimentos biocompatíveis e estáveis, que apresentem propriedades mecânicas adequadas, e que não sofram ruptura ou delaminação durante o uso, é uma solução muito promissora para melhorar o desempenho do 316 SS como biomaterial para implantes. Neste trabalho, uma liga intermetálica FeAlCr, que tem apresentado propriedades adequadas para a aplicação como biomaterial, foi utilizada como recobrimento sobre um aço inoxidável 316 de grau médico. O revestimento foi obtido utilizando-se a técnica magnetron sputtering por corrente contínua. Os parâmetros de deposição, como distância substrato - alvo e pressão de gás argônio foram mantidos fixos em 50 mm e 5 mTorr, respectivamente. As amostras foram preparadas com os seguintes valores de potência de sputtering: 50 W, 75W, 100 W e 150 W. A adesão dos filmes foi analisada por teste de scratch, enquanto a espessura e a taxa de deposição foram analisadas por perfilometria ótica. As características estruturais foram analisadas por microscopia eletrônica de varredura com EDS.

Aug 8, 2018

By Marco Antonio Meggiolaro

Most cyclic plasticity models used in multiaxial fatigue life predictions are based on a concept of a yield surface, which divides the elastic and plastic domains. Plastic straining occurs when the stress state reaches the surface and tries to move outward. Subsequent plastic straining causes the stress state to remain on the yield surface, which will translate to prevent the stress point from moving outside it according to a kinematic hardening rule that models the Bauschinger effect. The accurate modeling of the yield surface shape is fundamental to predict stress-strain relations. In this work, the main yield surface equations for isotropic materials are compared. Even though most materials can be modeled using Mises and Tresca surfaces, other need to consider the effect on the yield strength of the hydrostatic stress or the normal stress acting on a critical plane. It is shown that pressure-sensitive models originally devised for concrete can be applied to predict yielding in some materials, and even fatigue life for metallic structures with short cracks.

Aug 8, 2018

By Alexandre Dolabella Resende

O estudo do padrão de fluxo do aço no molde de lingotamento contínuo é de grande importância para a siderurgia, uma vez que permite compreender como as variáveis de processo afetam a qualidade do aço produzido. Existem diversas técnicas, numéricas ou experimentais, utilizadas para realizar esses estudos. Este trabalho apresenta um estudo de simulação numérica, que tem como objetivo avaliar a influência da fração de argônio injetada no sistema no padrão de fluxo do aço no molde de lingotamento de placas. As condições de processo simuladas foram obtidas de diversas máquinas de lingotamento, com diferentes vazões de aço e argônio injetado. Os resultados numéricos foram validados através de um método experimental denominado “Nail Board”. Após a realização do estudo, foram constatadas consideráveis alterações do padrão de fluxo devido à variação da fração volumétrica do argônio injetado no sistema.

Aug 17, 2017

By Karl K. Bagger, Felipe Bertelli

The competitive scenario of steel industry requires studies and developments to improve manufacturing processes focusing on increasing productivity and reducing costs. The practice of coating rolls for cold rolling with the chrome aims to increase the rolling campaign, reducing their wear by increasing the surface hardness, which guarantees a greater homogeneity in the surface of the rolled products. The present paper presents a study on the effect of the chromium coat on a forged steel rolls on the wettability of a SkinPass solution. The hardness of the coated layer and the contact angle were measured for two concentrations of solution on two types of surfaces, comparing the coated and uncoated surfaces. The results show that there is an influence of the coating on the wettability of the fluid when comparison are made with chrome coated and uncoated materials, being verified through tests in Goniometer. The productivity of the coated rolls showed higher productivity than the uncoated ones.

Oct 1, 2019

By Nicolás Ariel Zabala

During the make-up and break-out of the connections, threaded joints are exposed to intense mechanical and tribological solicitations. The connection performance is influenced by its geometry, material properties, surface treatments and thread compound. The aim of this work is to evaluate and characterize the tribological behavior of different thread compounds applied on manganese phosphated carbon steel under low speed and high pressure sliding contact. Four thread compounds were evaluated: one containing lead, zinc and graphite; other lead-free, containing copper and finally, the last two lead-free and containing non-metallic solids. The tribological behavior was analyzed by a block-on-ring tribotest. During the test, load varied linearly between 250 N and 7000 N; loading and unloading lasted 14 sec and were performed in opposite directions of rotation to simulate the make-up and break-out operations. Friction force and load as a function of time were registered. Upon completion of the test, wear surfaces were analyzed by SEM, optical microscopy and energy dispersive spectroscopy. The obtained results show that the lead and zinc containing thread compound displayed the best behavior, showing a wear reduction of approximately 20%. These results are in line with previously known oilfield experience. Average COF values around 0.15 were measured and no significant differences between dopes were observed; indicating that the wear behavior was influenced by the additive package.

Jul 31, 2018

By Leandro de Almeida

Tiras e chapas de cobre e suas ligas possuem excelentes propriedades térmicas, elétricas e mecânicas simultaneamente e por isso podem ser utilizadas na fabricação de inúmeros produtos através de processos de conformação. Determinadas características devem ser analisadas na chapa antes mesmo do processo de manufatura, visando eliminar possíveis falhas durante as etapas de produção. Especificamente para o processo de repuxo profundo, faz-se necessário avaliar a possível formação de orelha e o possível afinamento da espessura da chapa durante a conformação. Sendo assim, o levantamento dos coeficientes de anisotropia planar ?r e o de anisotropia normal r são essenciais para se obter bons resultados nos processos de conformação. O presente estudo tem como objetivo avaliar a influência da deformação (e) na obtenção dos coeficientes ?r e r na liga UNS C22000, utilizada especificamente para a produção de projéteis A norma ASTM E 517 que apresenta a metodologia para se determinar esses coeficientes não especifica claramente qual e a ser utilizada. Os resultados alcançados não demonstram diferenças significativas com relação a e utilizada nos ensaios, ou seja, os coeficientes obtidos utilizando 0,10, 0,15 e 0,20 de deformação são os mesmos.

Aug 17, 2017

By Érico França Oliveira e Silva

O conceito de utilização de aços microligados de elevada resistência mecânica nas estruturas automotivas como forma de reduzir peso, aumentar desempenho, reduzir o consumo de combustível e proporcionar maior segurança, já está bem difundido na indústria mundial. A CBMM vem desenvolvendo um projeto com a equipe da Unicamp que compete na Fórmula SAE como um meio de difundir o conceito da aplicação dos aços microligados para aqueles que serão a próxima geração da tecnologia automotiva. O projeto foi iniciado em 2011 e praticamente todas as peças do protótipo foram trocadas de aço AISI A36 para vários tipos de aços microligados com limite de escoamento superiores a 700MPa. Esse trabalho apresenta exemplos de componentes onde as reduções em massa atingiram até 32%.

Aug 7, 2018