Search Documents

By Sathit Tandanand

This report presents a Bureau of Mines study on the time-dependent behavior of coal measure rocks for future implementation in stability analysis and safety evaluation of in-mine rock structures. This initial study focused on moisture adsorption rate and strength degradation of shales in Pennsylvanian coal-bearing strata in the Illinois Basin. A reaction of clay minerals in Illinois shales with atmospheric water vapor was hypothesized as the adsorption and strength degradation mechanism. Part of energy exchange between shales and the environment was attributed to a free energy controlled by pore pressure of the rock and partial pressure in the environment. The relationships between adsorption versus time and strength degradation versus moisture content were derived and correlated with the experimental data. Partial saturation at various levels of relative humidity occurs within approximately 2 weeks at room temperature. The strength of shales tested decreases linearly with increasing moisture content. When the moisture exceeds 7 pct of the dry weight, these Illinois shales become unstable. To this end, the moisture content is a good predictor of rock strength for shales.

Jan 1, 1987

By E. C. T. Chao

Micro-optical and synchrotron radiation-induced X-ray fluorescence (SXRF) techniques have been used to study unoxidized and oxidized samples of Carlintype sedimentar,y rock-hosted disseminated gold ore. In these samples, Where much of the gold is submicroscopic, the SXRF technique, which has a spatial resolution of about 20 ~m and a minimum detection limit (MDL) in the ppm range, is an ideal and necessary tool for precisely locating gold-rich areas in a sample. Gold-rich areas pinpointed by SXRF were later studied in detail by micro-optical methods, principally optical microscopy and scanning electron microscopy with energy-dispersive X-ray analysis (SEM-EDX). In two unoxidized and one oxidized ore samples, SXRF analyses have shown gold to be present predominantly in discrete clay-rich and silicified areas. Gold was not detected by SXRF in association with pyrite or carbonaceous materials. SEM-EDX examination of the gold-bearing areas in the unoxidized samples succeeded in identifying only two free gold particles, 0.2 and 0.5 ~m in size. In the oxidized sample, gold particles appear to be larger (but still submicroscopic) in average size and more evident in micro-optical examination after SXRF location of goldbearing areas. The findings of these studies may help to improve the efficiency of processing and recovery of gold from unoxidized ores.

Jan 1, 1987

By B. F. Naylor, C. H. Shomate, F. S. Boericke

"Ilmenite is the most important titanium-bearing constituent of titaniferous iron ores. Such ores, of which the United States has abundant reserves, are of interest because they constitute an important potential source of both iron and titanium that may be tapped in times of stress, and which eventually may be utilized in the normal course of events.As the iron and titanium constituents of titaniferous iron ores are not completely separable from each other by ore-dressing methods, any process for metal recovery will, of necessity, involve reduction of the iron in ilmenite. Consequently, knowledge of the thermodynamic properties of ilmenite should supplement information already available concerning those ores. With this in view, the Pacific Experiment Station of the Bureau of Mines undertook to evaluate thermodynamic properties; the data obtained are the subject of this report.Three types of experimental work were involved. First, low-temperature specific heats of ilmenite were measured in the temperature range 500 to 29S° K. These data serve to evaluate the entropy, a quantity necessary for a reliable evaluation and correlation of other thermodynamic properties. Second, high-temperature heat-content measurements were made in the temperature range 298° to 1,743° K. The data serve to bridge the gap between room temperature and elevated reduction-process temperatures. Finally, hydrogen-reduction equilibria were measured in the temperature range 1,220° to1,375° K. These data-give a direct measure of the free energy of reduction of ilmonite at these temperatures and, in conjunction with results of the other two types of measurements, serve to obtain the heat of formation of ilmenite, a quantity not readily determinable by direct calorimetric means.The data are correlated to form a composite, self-consistent portrayal of the thermodynamic properties of ilmenite, which may be used in evaluating the efficacy of any reducing agent of known thermodynamic properties. Selective-reduction of iron in ilmenite by hydrogen, carbon monoxide, and carbon are considered in this report."

May 1, 1946

By M. S. Frasad

The State of Minnesota is interested in stimulating the development of clay resources and recently supported a two year project to collect data on geological, mineralogical, processing, economic and environmental aspects of such potential developments. This paper presents the .various process options adopted on the bulk samples collected from the Minnesota River Valley area which is a primary deposit and contains a major silica fraction. A standard test flowsheet involving degritting, dispersion, HGMS, and cycloning was developed and for some samples yielded an acceptable filler grade product. Secondary streams containing relatively high grade kaolin but of coarse size were also obtained. Improvement in particle size distribution and in physical properties related to paper product specifications (brightness, viscosity) were obtained by size reduction processes. Market and economic considerations for kaolin consumption in the upper Midwest are analyzed. Current markets for paper grade kaolin in Minnesota were briefly discussed.

Jan 1, 1990

By D. E. Wolfson

Twenty-two samples of West Virginia coals were carbonized at 9000 C by the Bureau of Mines-American Gas Association (BM-AGA) method, and yields of products and physical properties of cokes were determined. Eighteen samples represented the Coa1burg, No. 2 Gas, No. 2 Gas and Peerless, Powellton, Eagle, Big Eagle, Lower Eagle, Sewell, Fire Creek, and Pocahontas No.6 beds in Fayette County, and four samples represented the Sewell and Fire Creek beds in Greenbrier County. Expansion characteristics of the majority of samples were determined in the Bureau of Mines sole-heated oven. Chemical analyses were determined for all coals. The coals in Fayette County are high-volatile A, medium-volatile, and low-volatile in rank, and the Greenbrier coals are medium-volatile in rank. Most of the coals are chemically suitable for metallurgical coking. All coke strength indices are within acceptable limits for metallurgical coking coals. All the high-volatile A coals contracted and the medium-and low-volatile coals expanded in the sole-heated oven expansion test.

Jan 1, 1966

By G. W. Birge, D. E. Wolfson, J. H. Lynch

This report by the Federal Bureau of Mines describes the carbonizing properties of coals from the principal beds in Boone County , W. Va . Results are given for samples of coals from No. 5 Block , Stockton - Lewiston , Coalburg , Winifrede , Chilton , Hernshaw , Cedar Grove , Alma , and No. 2 Gas beds . Boone County coals rank as high -volatile A bituminous . Eighteen of the 21 samples tested contained from 3.3 to 7.9 percent ash and 16 of the samples contained from 0.6 to 0.9 percent sulfur . Two samples from the Alma and No. 2 Gas beds , the lowest stratigraphically of the seams tested in Boone County , contained from 1.4 to 2.7 percent sulfur . Most Boone County coals yield

Jul 1, 1960

By Morton Corn

The U. S. Federal Coal Mine Health and Safety Act of 1969 placed limits on the permissible concentration of airborne respirable coal mine dust. Evidence exists which suggests that the effects on health of respirable coal mine dust may depend on both host factors and dust properties other than concentration. Dust particle size, shape, density, specific surface area and chemical composition are among the dust parameters of interest in an epidemiological investigation of coal workers' pneumoconiosis and coal miner exposure to mine dust. The purpose of this investigation was to develop and demonstrate the feasibility of techniques to determine selected properties of respirable coal mine dust. An approved underground horizontal elutriator which samples air at 36 cfm was designed, fabricated and utilized in this study to collect respirable coal mine dust in three mines representing the Pittsburgh, Lower Freeport and Lower Kittanning coal seams. Analytical procedures for measurement of respirable dust sample particle size, density, random projected area, total surface area and chemical composition are presented. Results of analyses of three samples collected in each mine are presented. Up to five full work shifts of sampling were required to accumulate approximately five grams of respirable coal mine dust in each sample. Statistical tests were applied to determine the significance of differences between properties of dust samples collected in the same mine and between arithmetic mean values of dust properties representing three samples collected in each mine. A comparison was also made between

Jan 1, 1972

By R. W. Pauls

"Many tens of thousands of hectares of forested land will be disturbed and reclaimed in the surface mineable Athabasca oil sands area during the next few decades. The surface area disturbed by Syncrude’s Mildred Lake development alone exceeds 10 000 ha to date. It is not clear that reforestation of disturbed areas will best accommodate the aspirations of all stakeholders, particularly traditional users of the land. A five-year research program by Syncrude Canada Limited and the Fort McKay First Nations has examined the feasibility of raising bison on land reclaimed after disturbance by oil sands development. Forage productivity and carrying capacity for bison was comparable to that of grasslands elsewhere in Alberta. Concerns regarding compaction of newly rebuilt soil by bison traffic proved unfounded. Bison demonstrated weight gains typical for ranched bison and calving rates averaged 90%, a value typical for ranched bison. The animal husbandry problems encountered were typical of those occurring on bison ranches elsewhere in Alberta. An economic analysis indicates that a 1000 ha bison ranch on reclaimed land has a net present value that compares very favourably with a similar area supporting commercial forest. Subject to approval by Alberta Environmental Protection, the current research project will be expanded as a pilot commercial ranching venture in order to explore its commercial viability as a business venture by the Fort McKay First Nations. At the same time, measures will be implemented to resolve various regulatory issues associated with commercial bison production in the oil sands area.BackgroundSyncrude Canada Ltd. (Syncrude) is proposing, in its land reclamation strategy, a feature that is, depending on one’s background and perspective, regarded as an innovative approach to land reclamation, a threat to the regional forest industry, a creative response to aboriginal stakeholder concerns, a reneging on reclamation commitments, an opportunity to provide an ongoing economic base for postoil sands regional economy, or an environmentally unsound use of the land. These diverse and sometimes strong reactions have been generated by the proposal to introduce bison, either free-ranging or commercial ranched, to the reclaimed landscape."

Jan 1, 1999

By S Azam

Coal is a vital energy source and source of carbon for metallurgical applications, contributing significantly to the world economy. Coal mining and processing involve multiple processes that generate Respirable Coal Mine Dust (RCMD), one of the primary sources of health hazards for coal workers. Since 2000, the rate of Coal Workers’ Pneumoconiosis (CWP) has continually increased in the U.S, with severity of the cases also worsening. Increasing evidence shows that exposure to RCMD in coal workers is a high-risk factor for lung cancer, which causes more deaths than the following three major cancers combined in the US Recent observations show an increased incidenceof CWP or other lung diseases, particularly among young miners in the Appalachian basin. The CWP prevalence in Appalachia is four times higher than the national average. Although various regulations are in place, the resurgence of such disease among coalminers demands additional efforts to better understand all the possible facets of coal dust toxicity, taking insights from current interdisciplinaryresearch efforts. One such important field is the interaction of coal dust with moisture in underground mines. Although moisture is prevalent and dynamic in an underground mining environment, it has never been evaluated for its impact on modifying the toxicity of coal dust and transport or flow behaviour. However, research conducted in atmospheric sciences in the past decade makes it clear that moisture in the atmosphere can significantly alter the behaviour of mineral dust. This paper is a part of research aimed at understanding how moisture interacts and alters the characteristics of coal dust. Such insight is crucial in understanding the potential toxicity of coal dust and developing mitigation technologies.

Oct 12, 2022

By J. P. BONARDI, C. W. Davis, R. B. Moore, J. W. MARDEN, S. C. Lind, J. E. Conley

The rare metals are becoming increasingly important to our industries. Rare-metal alloys have properties which indicate that we are only on the threshold of the possibilities of their utilization, not only in making nonferrous alloys, but also as special steels. Not only are their uses broadening rapidly, but the metals are affecting our industries in other ways. The oxides and some salts are used as pigments; others have medicinal value. The pure metals are made into filaments for incandescent lamps, and targets for X-ray tubes. By their efficient use in alloys, the weight of automobiles is reduced, • and the wear and tear on tires and roads is thus minimized; in machine shops they help to give greater efficiency to tools and reduce production costs. Their development has marked a milestone in the progress of civilization. There has been considerable uncertainty regarding analytical methods for the rare metals. A great deal has been published, but the weak and the strong points of the various methods have not been investigated as carefully as is needed. The Bureau of Mines at its Rare Metals station in Colorado necessarily had to do a great deal of analytical work in connection with the metals covered by this bulletin, which aims to give the results of the experience so acquired. No claim for much originality is made, although some published methods given have been modified, and some new ones have been developed by members of the staff. The principal methods available were studied critically, and it is to be hoped that the work will assist those interested in analytical work in connection with the metals named.

Jan 1, 1923

By I. E. Odom

A study was made of the physical and chemical nature of silica minerals found as natural impurities in bentonites and montmorillonitic Fuller&apos;s earth clay products as well as in <10 micron dust from eight processing plants. The results show that the silica minerals present in these clay materials are totally encapsulated or encased in clay. No "free" silica minerals could be observed in SEM images of either granular or powder products or in dust samples collected for MSHA crystalline silica analysis. Silica minerals, such as quartz, are identifiable by SEM and EDS analysis only after removing the clay coatings by vigorous washing. After washing it can be observed that all crystalline quartz grains also have diagenetic overgrowths of what is probably opaline silica. The clay and opaline silica encapsulation of quartz plus the strongly hydro scopic nature of montmorillonite are believed to be responsible for there not being a single confirmed case of silicosis among workers in the subject plants after more than 65 years of production.

Jan 1, 1996

By Slavoljub D. Maksimovic

At some coal mines, methane gas is released during raise drilling. At the request of the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, the Bureau of Mines conducted ventilation surveys at different raise drill sites to assess various methods of reducing methane concentration. The resulting data indicate that raise drill shaft cavities are ventilated by air compressors, vacuum pumps, auxiliary blower fans, and free intake air from the surface. The compressors, pumps, and fans operate simultaneously or separately. At the bottom of the shaft cavities, ventilation is controlled by regulators and airlocks. Methane is monitored, measured, and periodically sampled on the surface, at the bottom, and at different levels in the shaft cavities. Maximum concentration of 3.5 percent was measured in one shaft in West Virginia. Air velocity down the raise drill shafts is always very low, Maximum recorded air down the drill stem was 3,000 cfm, which can be increased by adding air compressors. The best way to ventilate shaft cavities is through the simultaneous use of air compressors and vacuum pumps. If the methane concentration cannot be reduced with additional compressors, then the inside diameter of the drill rod should be increased, or larger pilot hole drill bits should be used.

Jan 1, 1981

By M. Dupuis

Recently, a new approach to controlling alumina feeding in a H.H. cell has been proposed [1, 2 and 3]. This approach, labeled In Situ aluminium cell control, is based on a correlation between the slope of the cell voltage during a no feed observation period and the dissolved alumina concentration in the bath. Once the dissolved alumina concentration has been estimated, a primary calibration surface uniquely relating the dissolved alumina concentration and the anode-cathode-distance (ACD) to the cell voltage is used to estimate the cell ACD. Once both the alumina concentration and the ACD have been estimated at the end of the observation period, a PID controller can be used to regulate the rate of alumina feeding using only the normalized cell voltage to calculate the error between the estimated dissolved alumina concentration and a target value. The In Situ aluminium cell control algorithm has now been tested with the Dyna/Marc [4, 5 and 6] cell simulator demonstrating that it should be possible to control a H.H. cell in this manner with less variation in the dissolved alumina concentration and other process variables producing a prediction of improved cell current efficiency and power efficiency.

Jan 1, 2011

By R. K. Jonas

"Pressure leaching and pressure oxidation in autoclaves are important alternatives in the extractive processing of gold, copper and nickel ores. The application of advanced control to pressure leach and pressure oxidation autoclaves could achieve significant benefits as has been shown in alumina pressure leaching. This paper compares and contrasts alumina digestion autoclaves to other mining autoclaves with respect to advanced controls. The application of advanced control in alumina with over 30 units controlled worldwide, and its benefits will be reviewed. The design and potential benefits from advanced control for pressure oxidation and leaching will be presented.INTRODUCTIONIt is this author's position and the purpose of this paper to propose that advanced control could be effectively applied to autoclaves in the nickel, gold, and copper mining processes. This is based on the proven effectiveness of advanced control on autoclaves used in the alumina industry for pressure leaching of bauxite ores. Incremental, but significant increases in production could be realized by applying advanced control to autoclaves, as evidenced by the alumina industry, and this not being implemented in other autoclaves in the mining industry.In addition, today the mining industry is being challenged to improve their production methods. In some markets like nickel, there is pressure to improve productivity and reduce the cash cost per ton. While in other markets like copper and gold, demand is vigorous with favourable pricing, and there are advantages to increase production and productivity given limited plant capacity. Advanced control has proven its capability to improve mineral processing operations through increases in throughput, recovery, as well as reducing variability. In today's mines, autoclaves are being used to a much larger scale and with much larger importance, thus it would be beneficial to improve operational performance through the use of advanced control.Accordingly, it is the author supposition that an opportunity exists in the mining industry to use a proven advanced control technology to improve the operations and financial performance of mines using autoclaves."

Jan 1, 2012

By Alla D. Mah

Titanium forms several compounds with oxygen and also is able to dissolve interstitially about 33 atomic percent of oxygen. Starting with titanium dioxide, reduction becomes increasingly difficult as oxygen is removed; and the final step, be reduction of the titanium-oxygen interstitial solutions, is by far the most difficult. The possibility of reducing titanium oxide, or of purifying titanium containing oxygen, by treatment with certain more volatile metals has been a subject of considerable interest. Theoretical appraisal of the limitations of this possibility, however, has been hampered by lack of adequate information on the thermodynamic properties of the titanium-oxygen solutions. The purpose of the present work was to remedy this difficulty by expanding the thermodynamic knowledge regarding these solutions. The experimental work involved three types of calorimetry and furnished the following information: (1) Heats of formation of 11 titanium-oxygen solutions, in the range of 0 to 10 wt.-percent oxygen, were determined at 298.15° K. As a byproduct, an improved value of the heat of formation of rutile was obtained, which, in turn, led to improved values of the heats of formation of the lower titanium-oxygen compounds. (2) Low-temperature heat-capacity data and entropies at 298.15°K in were determined for 2 representative titanium-oxygen interstitial solutions. (3) High-temperature heat-content data were obtained for 2 titanium-oxygen interstitial solutions to about 1,600° K.

Jan 1, 1957

By J. R. Odekirk

The nature of mineral distributions and locking characteristics in mill products are important factors in understanding mill performance. Such data are obtained by microscopic point counting methods. Reduction &apos;of point-count data from volume to weight percentages, and reduction of data for each size fraction back to a head sample requires lengthy hand calculations. The use of computer processing for such data reduction results in obtaining information on a realistic time basis. An example of computer processed point-count data is presented.

Jan 1, 1981

By C. F. Davidson

The Bureau of Mines studied the extraction of lithium from lithium-containing clays by chlorination with hydrogen chloride (HC1). In bench-scale laboratory investigations, HC1-H20 mixtures were used to selectively chlorinate lithium, but not calcium or magnesium, in lithium-containing clays. The addition of calcium carbonate to the clay was found to improve the lithium recovery. Reaction conditions found to affect the lithium recovery were ratio of clay to carbonate, reaction temperature, and HC1 concentration. The best conditions for selective chlorination of the lithium were 2:1 clay-carbonate, 750° C, and 20 wt-pct HC1. The experimental results and trends in lithium extraction are explained using thermodynamic relationships.

Jan 1, 1981

"The mission of the Respirable Dust Center is to enhance the health, safety and productivity of the miners 'through advancing the fundamental .understanding of all aspects of respirable dust associated with mining and milling and the interaction of dus.t and lungs for reducing the incidence and severity of respirable dust disease. All Dust Center activities are focussed to be responsive to this mission which is shared by several federal agencies closely associated with the Generic Mineral Technology Center for Respirable Dust such as USBM, M,SHA, and NIOSH, and the mining industry. While significant progress has been achieved in making mine atmospheres cleaner and healthier, respirable dust disease remains the nations worst industrial hazard. GOALSThe goals of the Respirable Dust Center have been formulated to recognize the diverse scientific, engineering and medical aspects of respirable dust as well as the need to enhance the interaction, education and technology transfer in the respirable dust area.The Center goals are to:1. Enhance the understanding of the scientific, engineering and biological characteristics of fine and respirable mineral particles, fibers, organic aerosols, and complex particles found in the mining and milling atmospheres.2. Advance the understanding of the physical behavior of airborne respirable dust particles in flowing streams under different. stimuli during mining and milling.3. Advance fundamental understanding of the causative mechanisms for the occupationally related lung impairments and the airway diseases of mine and mill workers.4. Establish the relationship between natural and cultural factors (mine geology, mineralogy, mining and milling methods, equipment and control measures) in the generation, exposures, and pathogenic properties of fine particles.5. Contribute to the development of control mechanisms for reducing ambient respirable dust concentrations, worker exposure, the incidence and severity of dust related lung disorders and disease prevention in mining and milling atmospheres.6. Enhance functional integration among the various research personnel in the Center, as well as, with other groups, such as MSHA, NIOSH and USBM involved in respirable dust research and control.7. Develop technically trained personnel for employment in the mineral industry for respirable dust research and control.8. Enhance the availability of respirable dust-related information utilizing several technology transfer avenues."

Jan 1, 1990

By M. Laframboise, M. Buarzaiga

High-pressure acid leaching (HPAL) of nickel laterites has received considerable attention in recent years. High paymetals extraction, good selectivity, and advances in pressure hydrometallurgical technology are some of the reasons for this interest. Falconbridge Limited (Sudbury. Ontario) investigated the HPAL process using both fresh water and seawater for ore processing. The use of seawater resulted in a chloride concentration of 7.8 g/L in the autoclave feed. A test program was developed to study the effect of process water and leach temperature on the leaching behaviour of different ore compositions from the Koniambo deposit in New Caledonia. The work showed that salinity has a major effect on autoclave chemistry. This paper explores the results.

Jan 1, 2004

By A. Vishwakarma, V. Himanshu, K. Dey

Underground mining is the most feasible method after extinction of shallow depth ore deposits. Longhole stoping method is the most technically advanced method for the faster excavation. In this method, the holes are drilled in the form of ring pattern and explosives are used for the rock breakage. During blasting, the explosive energy sometimes also breaks the non-ore material. The non-ore material gets included in the extracted ore and enhances the ore dilution. Few uncontrollable factors which affects the ore dilution are ore body characteristics, rock quality, insitu stress condition etc. Apart from uncontrollable factors, explosive energy and blast design also plays an immense role in ore dilution. In the blasting practice, the purpose is to effectively utilise the explosive energy for rock breakage. The optimum delay is required so that the blast holes attain adequate free face before the blasting. This paper deals with the optimisation of blast design parameters to reduce ore dilution in underground hard rock mining having narrow vein. The study was carried out using numerical simulation. The explicit dynamics based modeller of Ansys was used for this purpose. The parametric variations in the models were done to optimise the parameters. The burden has been optimised first by varying the width of the narrow vein. The blasts of a ring consisting of single hole were conducted in the model by varying the width of the narrow vein. The damage contour under different parametric variations were analysed. The experimental trial has been also carried out at Zawar Group of Mine, Rajasthan, India. The optimum parameter was decided based on the result of experimental trial and numerical simulation model. The output of the model shows that optimum burden for 3.5 m narrow vein width is 1.12 m and for 1.0 m, it is 1.54 m. This shows that the optimised burden is higher in the vein having lesser width as compared to the greater width. The presence of joints/changed media/interface (between the sidewall and narrow vein) is the major reason behind this. The wave gets reflected back very fast on coming in contact with joints in a 1.0 m narrow vein as compared to a 4.0 m narrow vein. This will quickly convert the compressive wave into tensile wave giving rise to tensile slabbing. Hence proper utilisation of explosive energy will take place for the breakage of rock mass when the width of the narrow vein is smaller. The burden obtained from the experimental trial and numerical simulation models is less than 2.0 %. Hence the numerical simulation based approach can be used for the assessment of the optimum burden for ring blasting in narrow vein under different geomining conditions. This helped in reducing ore dilution and maximization of ore recovery. In the future, empirical relationships may be developed by considering different geological discontinuity, the strength of the rock mass and explosive parameters.

Jan 1, 2024