Search Documents

By Nakahiro Y, Wakamatsu T

In the present study, from experimental results, a new concept of possibility of flotation separation of quartz from feldspar is presented. The effect of the nonionic surfactant Brij 58 on the flotation behaviour of quartz and feldspar has been investigated. The effect of the surfactant adsorption at the solid-liquid interface was also studied. The results demonstrate that maximum flotability of quartz occurred at low concentration of surfactant. Feldspar is not collected by this surfactant. Flotation tests with feldspar that had previously been subjected to leaching by hydrochloric acid yielded similar flotation response as that of quartz. The effect of removal of alkali cations from feldspar surface on its flotability was investigated. The effects of inorganic and organic additives on the flotation recovery of quartz are discussed in terms of the slating-out or salting-in properties of these additives. KEYWORDS: Alkyl polyoxyethylene; feldspar; flotation; nonionic surfactant; quartz; salting-in; salting-out; separation; silanol groups.

Jan 1, 1993

By O. Ryosuke Suzuki

A new metallurgical process via sulfide is proposed: a sulfide is produced at a high temperature from its metallic oxide using gaseous CS2, and this sulfide is electrochemically reduced to its metallic state using molten salt. This combined process via sulfide is effective to obtain high purity of metallic powder, even if the metal in its oxide is strongly combined with oxygen. For example, it is not easy to reduce stable oxide TiO2, and only Ca can remove oxygen to form α-Ti. However, a fairly large amount of oxygen remains as Ti–O solid solution. Because the solubility of S in Ti is very small, this proposal was examined experimentally both on the conversion of TiO2 to TiS2 and on the successive reduction of TiS2 to Ti. TiO2 powder was exposed to CS2 gas flow at 1073 K, and the conversion to TiS2 was confirmed. TiS2 could be reduced to Ti powder either by calciothermic reduction or electrolysis in a CaCl2 melt. By Ca reduction at 1133 K in CaCl2 melt, sulfur concentration decreased to 0.03 mass%S when the amount greater than twice the stoichiometric calcium amount is added. By electrochemical reduction at 1173 K in CaCl2–CaS melt, S concentration significantly decreased to 0.01 mass% S when four times larger amount of electric charge was supplied.

By G. C. Branner

The bauxite diagram presented as figure 1 was developed to clarify, by graphic means, the theoretical chemical constituents of gibbsite-kaolinite-type bauxite for all possible proportions of these two minerals from pure gibbsite to pure kaolinite. The tables in the report reflect the same date. The diagram provides (1) a graphic representation of the relations of constituents with respect to a ill possible percentages of alumina and silica, (2) a basis for verifying the accuracy of analyses of gibbsite-kaolinite bauxite, and (3) a basis for estimating the type and proportion of alumina hydrate and/or silicate minerals that may be present in gibbsite-kaolinite-type bauxite. The diagram, with accompanying interpretations and use formulas, will be useful to those connected with the mining and processing of bauxite.

Jan 1, 1955

By S. S. Peng

In this paper, the precise definitions for a number of commonly used subsidence parameters are given. The subsidence parameters have been determined using an integrated approach for 110 subsidence cases collected in the major US coal fields. Attempts have been made to establish empirical formulae for the parameters. The results of this study indicate that some traditionally-held concepts should be changed.

Jan 1, 1995

By H. Staton, XPS Consulting & Testwork Services, T. Deng, M. Kelvin

"Lundin Mining’s Eagle Operation, located in Marquette County, northern Michigan consists of a mine and concentrator that processes a Ni-Cu-(PGE) ore. Mine production began in 2014 and is expected to achieve production of approximately 23,000 tonnes of Ni and 20,000 tonnes of Cu per year. The ore is trucked to the Humboldt Mill, where both a Ni and Cu concentrate is produced.XPS Consulting & Testwork Services (XPS) has assisted the team at Eagle since 2013. Prior to start up, the ore was piloted at the XPS lab in Sudbury, Ontario to demonstrate the concentrator flowsheet and establish flotation operating strategy. XPS consulting metallurgists worked closely with the Eagle team during the commissioning of the plant providing troubleshooting, sampling, metal balancing expertise and support. Finally, a series of monthly composites over a 6 month period was submitted for mineralogical characterization to assess plant performance, identify opportunities for improvement and to provide a baseline for the future operation.Lundin’s investment to test the ores ahead of mining and to team with XPS’s experienced mineral processing engineers to help commission the plant has led to the plant achieving concentrator production targets shortly after startup. The commitment to training and implementation of best practices, and a culture where ongoing testing is the norm, puts the Eagle Operation on sound footing for future operation.INTRODUCTIONLundin’s Eagle Mine is a subsidiary of Lundin Mining located in the upper peninsula of Michigan. The mine itself is an underground operation and the ore is trucked from the Eagle mine site 2 hours to the Humboldt mill.The ore is an ultramafic hosted high grade Cu Ni deposit and exists as either massive or semi massive sulphides. The high resource grade of Cu (2.49%) and Ni (2.93%) make this a valuable ore source. (Owen & Meyer, 2013) A metallurgical team was put together by Lundin to ensure the mill was designed and commissioned to optimize metallurgy in the shortest time from this valuable deposit. The commissioning plan targeted commercial production by Q1 2015."

Jan 1, 2016

By M Dean, M Nehring, P Knights, M S. Kizil

Integrated continuous mining techniques such as fully mobile in-pit crusher and conveyor (FMIPCC) systems offer inherent labour, energy and environmental benefits to deep pit metalliferous mines. However, before such systems become commonplace, a number of barriers must be overcome.This paper outlines a number of commonly perceived barriers to FMIPCC application, together with a number of suggested solutions. The paper advances a design approach for specifying FMIPCC systems for deep pit metalliferous applications. A novel FMIPCC configuration is advanced using a hydraulic excavator in backhoe configuration. Because of the requirement to minimise belt extensions, a mine planning approach is presented based on a series of parallel and radial belt conveyor moves.The FMIPCC system does not fully replace truck-shovel systems. In the proposed mine plan, sinking is undertaken with truck-shovel systems using a series of box cuts, whereas pit ‘widening’ activities are accomplished via the FMIPCC system. Because of inherent differences in mine sequencing, the net present value derived from the FMIPCC mine will differ markedly from that derived from traditional, nested-pit, truck-shovel mining approaches. Therefore, any comparison of the FMIPCC and truck-shovel approaches must take into account radically different mine planning approaches.CITATION:Dean, M, Knights, P, Kizil, M S and Nehring, M, 2015. Selection and planning of fully mobile in-pit crusher and conveyor systems for deep open pit metalliferous applications, in Proceedings Third International Future Mining Conference, pp 219–226 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By R Dunne

"Continuous improvement on metallurgical treatment plants is possible only when good data and analysis of the data are available. Good data implies appropriate and accurate mass measurement coupled with good sampling practices and accurate chemical analysis especially when carrying out monthly metallurgical metal reconciliations. Adequate characterisation of key samples (eg tailings, feed, concentrates and others) at timely intervals is an important part of a good continuous improvement program. The data from this will help identify opportunities to improve operation performance and thus profitability. Examples are provided of projects that have led to improved plant performance based on good metallurgical data collection and analysis.Citation:Dunne, R, 2016. Using Metallurgical Data to Drive Continuous Improvement, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 201–206 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By C. E. Augustine, B. A. Landry, P. Nicholls

"Wien bituminous coal is burned in a hand-fired up-draft boiler used for heating purposes it has a decided tendency to produce smoke. A design of furnace and a method of firing and attendance that are satisfactory for fuels low in volatile matter, as anthracite or coke, are not necessarily Satisfactory for bituminous coals. It is therefore becoming common practice to use a special design of furnace for bituminous coals, in order to facilitate the combustion of the volatile matter and soot. This is done by (1) providing a larger combustion space to give more time for the combustion, (2) construction that will produce a better mixing of the gases and secondary air supplied over the fuel bed, or (3) keeping the gases at a higher temperature by preheating the secondary air, as may be done by surrounding them with refractory surfaces, or causing them to pass through a fuel bed of hot coke. A furnace may be built to use any or all of these methods of smoke prevention.In Bureau of Mines Technical Paper 303, Blizard5 and others give tests on a large heating boiler when burning coke, anthracite, and bituminous coal. Certair alternative furnace arrangements were used, but there was no material change in the furnace design for the various fuels. Since that time the manufacturer has made modifications in design to adapt it for use of bituminous coal, and additional tests have been made to determine how this change affected the production of smoke and the efficiency of the boiler."

Jun 1, 1929

By Rong Fan, Roger Smart, Ning Xu

As part of an Australian Research Council project with Newmont and Newcrest mining companies studying the influence of clay minerals on rheology, hydrodynamics and flotation response, the cryo-SEM technique has been used to capture and image the clay (low crystallinity kaolinite Q38) aggregate structures in the flotation pulp immediately after collector and before frother addition. Samples were also collected from the earliest froth phase and the froth overflow corresponding to early and later concentrates. In this technique, a copper tube is filled with the sample during operation of the cell. The tube is immediately plunged into liquid nitrogen vitrifying the water phase before it can crystallise as ice thereby retaining the structures without volume or other physical change. After sublimation of the vitrified water surface, the aggregate structures are revealed and can be compared between pulp and froth phases from clays in different feeds and flotation conditions. The images from both low-clay ore and ore with clay content reveal various levels of aggregation as predominantly edge-edge connected aggregates similar to those found in our previous studies of high-clay tailings. For the samples from the ore with clay content, more extensive edge-edge clay strings are found in the early froth phase as compared to exiting froth overflow and the pulp phase with short edge-edge connected strings. It is suggested that the strings of clay particles result from edge-edge aggregation in the Plateau borders of the bubbles before breakage during sampling and the more extensive edge-edge aggregation in early froth phase is induced by crowding in the bubble borders. The clay strings collected into the overflow concentrate are almost all broken up compared with the Froth before drop-back. The implications for entrainment and entrapment mechanisms of gangue capture in froth will be discussed.

Jan 1, 2014

By Feng Gao

A general unsteady- state model, based on a cracked substrate, has been developed to account for reaction and diffusion within porous substrate during oxidation of Carbon Fiber Reinforced Carbon matrix (CIC) composites. The effects of several parameters, such as diffusion and reaction rate ratio, oxygen concentration, and composite density, on oxidation process are explored. Also, theoretical results for a set of parameter values of the CIC composites are compared with experimental data. It shows that the model predicted values agreed well with the experimental data in weight loss. Based on this model, quantitative predictions of oxidation of a composite with cracked substrate can be made.

Jan 1, 1993

By C A. Foss, K Blay, K Leslie, D Hillan

Magnetic field studies provide remote sensing of magnetisation distributions and a means to investigate moderately- to strongly-magnetised ore deposits that may be partially or totally buried. However, above-surface magnetic field surveys have limited capability to resolve the detail of magnetisation distributions because of the large separation between the magnetisation and the magnetic sensor. While some of this detail is available from magnetic susceptibility logging within boreholes or from magnetisation studies on recovered core, these measurements are limited to the exact trace of the boreholes. The large disconnect between ground or aeromagnetic surveys and highly-localised borehole sampling can cause problems in developing robust source models from magnetic survey data. The measurement of magnetic field in boreholes has the capacity to at least partially bridge that gap by measuring the magnetic field due to magnetisations proximal to, but not intersected by, the boreholes.CSIRO has developed the world’s first downhole magnetic tensor gradiometer. This instrument measures magnetic field gradients in all directions within a borehole. A prototype instrument has been built and tested as part of phase 1 of the Deep Exploration Technologies Cooperative Research Centre (DET CRC). The prototype performed well with magnetic pyrrhotite at the DET CRC test site in the Adelaide Hills and at Carpentaria’s Hawsons magnetite deposit south of Broken Hill. Further work is required to reduce the diameter of the probe so that it can operate in NQ holes (it is currently limited to HQ or wider) and to transform it to a continuous logging tool. The borehole tensor gradiometer can be used to investigate the continuity of magnetisation over a distance of several metres to tens of metres away from a borehole intersection and the structural dip of the magnetic body. It can be used to either replace or augment downhole magnetic susceptibility logging. This instrument is one component of an integrated CSIRO suite of new magnetic field utilities and methodologies for iron ore exploration and development.CITATION:Leslie, K, Foss, C A, Hillan, D and Blay, K, 2015. A downhole magnetic tensor gradiometer for developing robust magnetisation models from magnetic anomalies, in Proceedings Iron Ore 2015, pp 299–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By E. Szelag

The adsorption and stabilization of mineral dispersed systems by using Pluronic copolymers with different molecular weights and EO content has been studied. The role of sequential adsorption of EO-PO copolymers and cationic surfactant (CTAB) on the carbonate particle properties and in determining the stability of their suspension was studied with particular attention to the conformation of the polymer at the solid-liquid interface. The purpose of this work was to investigate the flocculation phenomena, influence of polymer molecular size on stability of suspensions of magnesite and dolomite and the effect of addition mode of polymer and surfactant. The suspension stability measurements and the determination of sedimentation speed were carried out using an optical analyser (Turbiscan). In most of investigated cases, the biggest floccs and the fastest sedimentation were found for low concentrations of copolymers.

Jan 1, 2014

By Kremena Dedelyanova, Tsvetan Damyanov, Nikolay Hristov, Evgeni Kostadinov, Lubomir Kuzev

"Spherical grinding media (balls) are the most widely used media for comminution of ores by grinding. One way to optimize the grinding process in a tumbling mill is associated with the development and testing of a new media shape. By modelling simulation study of the behaviour of two types of grinding media (balls and tetraballpebs) in the grinding process was conducted to determine the possible advantages of the new media shape. Tetraballpebs are in the shape of tetrahedrons with spherical convex walls. D305 mm and L305 mm Bond ball mill sizes were used in the experiment. They are modelled milling tetraballpebs bodies corresponding by weight to five ball sizes, namely ¾, 7/8, 1, 1¼ and 1½ inches which form the grinding media used in a Bond ball mill. They are cast steel grinding bodies. Studies carried out with both types of grinding media include equal number of milling bodies of the same weight and volume. Having thus ensured a uniform mass of the grinding media and the same number of milling bodies, all other conditions and process parameters being identical, conclusions can be drawn about the influence of the grinding media shape on the grinding process. Compared to steel balls, the tetraballpebs used in laboratory tests carried out in closed cycle by Bond ball mill and the study of the rate of grinding gave five to six per cent higher yield of a control size of minus 0.1 mm. Measurements of the Bond ball mill power consumption demonstrated that tetraballpebs grinding media achieved energy saving of 4.7 per cent for the production of one gram of the control size of minus 0.1 mm."

Jan 1, 2014

By David Leidel, Beth Shimer, James Stuart

Periodically, the Institute of Makers of Explosives Safety Library Publications are reviewed, edited and updated to reflect recent technical developments, new commercial explosive products and new regulatory requirements. The rapid proliferation of electronic devices, particularly portable communication systems, inventory management devices, navigational aids, etc., required the revision of the IME Safety Library Publication 20, “Safety Guide for the Prevention of Radio Frequency Radiation Hazards in the Use of Commercial Electric Detonators”. The new edition of SLP-20 has been updated to correct alterations to U.S. frequency allocations and maximum transmitted power permitted and a discussion of communications and tracking systems required in underground mining by the Miner Act. Also, an entire section was added dedicated to safe distances from RF sources to the special type of resistorized electric detonators used in the upstream oil and gas industry on wellsites and an enlarged section describing the particular types of RF sources that the blaster may encounter, perhaps in construction blasting operations.

Jan 1, 2012

By Guy A. Johnson

Combining contract and in-house research, the Bureau of Mines has developed and inmine-tested a novel device to improve the field-of-view of operators of off-highway mining equipment. This device utilizes a downward-looking, flat fresnel lens. The lens, plus louvers to reduce glare, is housed in a protective steel structure. The complete unit is called a blind area viewer. The viewer, when mounted on the right- front corner of the deck of most large haulage trucks, will increase a driver's direct field-of-view from about 35 pct (of where he/she has to drive) to about 80 pct. The improved visibility allows the driver to see possible collision hazards and roadway obstacles better, thus improving mine safety and increasing productivity. Economic analysis shows that the blind area viewers, which are now commercially available, pay for themselves in about a month on a 170-ton-capacity truck. The viewers are also applicable to other large mining equipment, such as front-end loaders, draglines, and downhole drills, or any place where seeing around a corner would be advantageous, such as along conveyor flights in processing plants during startups.

Jan 1, 1983

By Jackson G. Jenkins

Magma Copper Company's San Manuel SX-EW facility has operated since May, 1986. The original facility had a design capacity of 25,000 tons per year of electrowon copper cathode produced by processing pregnant leach solution from an open pit/heap leach operation. In 1988, the plant was expanded to 50,000 tons per year to incorporate processing in-situ leach solutions. This paper focuses primarily on the heap leaching area with regard to exploration, testing, feasibility, permitting, design and construction, and operating practices. Research utilizing surfactant leaching aids to enhance copper recovery is also discussed.

Jan 1, 1993

By Guohui Zheng

The ever increasing quantities of solid wastes generated by various industries are at the source of the growing need for proper waste disposal methods. Thermal treatment of combustible wastes is a proven technology which permits the reduction of hazardous material having to be landfilled. However, this method is not universally applicable to waste disposal. For example, the transferal of heavy toxic metals into the thermal remediation products is a major issue of public concern. This paper focuses on the analysis of morphology changes from solid sludge to ash which is a product of the sludge combustion. The morphological parameters analyzed were particle size and external surface. They were determined using Jeol 840 Super Probe. The experiments were conducted in a computer-controlled high-temperature combustion system consisting of the thermogravimetric furnace coupled with Fourier transform infrared spectrometer (TGA-FTIR). Sludge particles were made of complex fibers trapped in the aluminosilicate matrix. At low temperatures, up to 680 K, the solid residue looked similar to the initial sludge. Between 680 K and 1180 K the sludge underwent intensive burning and steadily changed into powdered ash. At the temperature of 1050 K the ash was composed of separate, flat flakes with sizes ranging from 5 to 20 um. At 1470 K the flakes aggregated into large particles. The surface observed at 1670 K was a mixture of mullite crystals. Such structure could result from the solidification of the ash material after its melting. Morphological changes influenced the distribution of metals in the solid residue. For example, Cr was concentrated in small aggregates. Such distribution should allow for recovery of valuable metals from the solid waste residue.

Jan 1, 1996

By N. Baloyi, P. Popoola, M. Tlotleng, S. L. Pityana

"The advantages of using Nb and Ti-Nb coatings for improving the hardness and corrosion resistance of Ti6Al4V were investigated. It has been reported that Ti6Al4V used in orthopaedic implants tends to release toxic Al and V ions into the surrounding tissue. Thin layers of Nb and Ti-Nb were deposited on Ti6Al4V substrates using a laser metal deposition technique. The deposited material was analysed using optical microscopy, scanning electron microscopy coupled with energy dispersive spectroscopy, and X-ray diffraction. The corrosion behaviour of the deposited layers was investigated using a Metrohm Autolab PG Stat101 compact potentiostat at 25°C in simulated body fluid. A Vickers hardness system was used to study the mechanical properties. Both Nb and Ti-Nb coatings exhibited good metallurgical bonding with the substrate. The microstructure and the XRD analyses for the Nb system showed that the ??-Nb phase was most dominant, while the Ti-Nb system comprised a mixture of the ?? and ?? phases. The average hardness of the Ti6Al4V substrate was 350 HV0.3, with a slight increase for the Nb coating (363 HV0.3) and a much higher hardness from the Ti-Nb coating at 423 HV0.3. The corrosion results show that the deposited Nb was more corrosion-resistant in the solution than either the Ti6Al4V substrate or the Ti-Nb coating. IntroductionMetals such as CoCrMo, 316L stainless steel, and NiTi alloy are used for manufacturing biomedical implants because of their distinct properties, including low Young’s modulus and resistance to corrosion (Ryan, Pandit, and Apatsidis, 2006). These implants are required to remain in the body of the patient for many years. Due to a favourable combination of mechanical and corrosion properties, titanium (Ti) and its alloys have emerged as the material of choice for biomedical implants. Nevertheless, their use is not entirely without challenges. For example, in total hip replacement, surface degradation and release of metal debris from metal erosion caused by friction limit the service life of the implant (Oldani and Dominguez, 2012; Manivasagam, Dhinasekaran, and Rajamanickam, 2010). Ti6Al4V is generally regarded as the material of choice, but it has been found that over extended periods of time, the combination of surface corrosion and erosion releases toxic aluminium (Al) and vanadium (V) ions into the body (Khan, Williams, and Williams, 1996). This has led to the investigation of titanium alloys containing niobium (Nb), zirconium (Zr), tantalum (Ta), and molybdenum (Mo) as substitutes for the aluminium- and vanadium-containing Ti6Al4V (Okazaki et al., 1997)."

Apr 1, 2019

By Akira Yazawa, Kazuo Koike, Mitsuhisa Hino

"The vapor pressures of MS (PbS, SnS and Sb2S3) in the molten Cu2S-MS, FeS-MS pseudo-binary and Cu2S-FeS-MS ternary systems were measured by means of a transportation method in the temperature range of 1323 and 1423K to calculate MS activities in the sulfide melts. The activities of MS in these systems show negative deviation from ideal behavior except the FeS binary systems which exhibit nearly ideal behavior in the homogeneous melts. The activities of the Cu2S-FeS pseudobinary system, which is fundamentals of the copper matte, were estimated from the activity values in the ternary systems and exhibit negative deviation from ideality.The distribution behavior of tin between the ·matte and silica saturated fayalite slag was investigated under the controlled partial pressures of S02 at l 523K. It was found that, in general, tin is distributed in the both phase, while tin is concentrated to the slag phase with increasing copper content in the matte. The activity coefficient of SnO in the slag was calculated based on the distribution ratio combined with the activity coefficient in the Cu2S-FeS system.IntroductionThe thermodynamic properties related to the Cu2S-FeS system and the Cu2S-FeS-MS systems (where MS can be PbS, SnS, Sb2S3, As2S3, Bi2S3, etc.) is required to be better understanding of the copper smelting process. However, thermodynamic analysis such as the distribution of impurities among the gas, slag and matte phases is difficult due to lack of thermodynamic data. In this study, the vapor pressures of MS (PbS, SnS and Sb2S3) in the Cu2S-MS, FeS-MS. and Cu2S-FeS-MS systems were measured by a transportation method. The distribution behavior of tin between the matte and silica saturated fayalite slag was also investigated. The results in the present experiments are useful to analyze thermodynamically the behavior of component in the copper matte smelting."

Jan 1, 2000

By Güven Önal, Zeki Dogan, Neset Acarkan

In this study, it was aimed to produce glass sand with less than 0.15% Fe2O3 for window glass manufacture and glass ware grade with less than 0.05% Fe2O3 from Yalõköy sand dunes having 0.48% Fe2O3. In order to reduce the iron content of the Yalõköy sand dune, magnetic separation, flotation, scrubbing, H2SO4 leaching and drying were used. The optimum iron removal was achieved by H2SO4 baking at 150oC and 8 kg/t acid consumption. In this way, sand concentrate was obtained with 0.04% Fe2O3 and sand recovery 95%.

Jan 1, 2003