Search Documents

By Donald Wagstaff, D. Scott Scovire

The Coeur Rochester Mine is the largest primary silver surface mine in North America. Throughout its 17-year life, gold and silver grades leaving the tertiary crusher have typically been, on average, slightly below the mined bench grades as determined by blast hole assays. On a project-to-date basis, this grade variance is well within industry standards. While these variances are acceptable, mine personnel continue to study ways to further minimize the grade differences. One suspected cause for lower than expected head grades are ore loss and dilution resulting from blast-induced shot movement. In regard to grade control, the underlying design principle for non-electric blasts is the generation of uniform movement of the blasted rock material. Using one or two uniform directions of initiation, ore control methods at Rochester currently include adjusting flag lines on the muckpile in an attempt to account for displacement from original, pre-blast locations. To improve upon standard non-electric blasting practices, a series of evaluation blasts using an electronic initiation system (Orica i-konTM) was conducted in the summer of 2002. The primary objective of the evaluation blasts was to design shots that would segregate the ore and waste blocks into distinct muckpiles. Due to surface delay burning front limitations, truly effective ore and waste segregation blasting is difficult to accomplish with non-electric initiation systems for all but the most basic of ore geometries. The electronic detonator evaluation blasts produced visible boundaries in post blast muckpiles, identified by troughs or low areas, that closely matched the actual locations of pre-blast ore control flag lines based on blast hole assays. By blasting the ore and waste into distinguishable piles that were flagged and excavated accordingly, it is believed that blast-induced ore loss and dilution was reduced.

Jan 1, 2004

By J. Jakumelt

The coupled simulation of mold filling and solidification for an investment casting process presents difficult. This is due to the complexity of the carious physical process and the geometry, To achieve this task in a precise way, the CFD program FLUENT and the casting simulation tool CASTS were closely coupled. Any physical quantity, such as velocities or temperatures, can be exchanged via files after each time step of the simulation. The communication and operating sequence of the programs is controlled by PERL-scripts. This enables the expertise of FLU ENT for flow simulation and the strength of CASTS, for casting simulation to be combined. The coupled simulation was successful applied to an aerospace investment casting. Several physical models were tested for correct treatment of the casting filters, the porosity of the mold and the viscosity of the liquid metal. The results demonstrate that even complex investment casting geometries can be investigated using CASTS-FLUENT.

Jan 1, 2003

By F. P. Haver

The purpose of this investigation was to determine the effect of common impurities, that is, oxygen, nitrogen, carbon, and iron, on the Brinell hardness of electrolytic titanium. On a weight basis, nitrogen had the greatest hardening effect, followed by oxygen, carbon, and iron in order. The hardening effects of oxygen and carbon were almost identical up to a concentration of approximately 0.1 percent by weight. Above this concentration, the relative hardening effect of carbon decreased rapidly, possibly because of its limited solid solubility in a-titanium. Hardness vs. composition curves for both oxygen and nitrogen were essentially straight lines over the range of Brinell hardness numbers (B.h.n.) covered in the investigation. The hardness of titanium was also determined as a function of the percentage of impurity atoms. On this basis, iron in concentrations up to 0.17 atomic percent had a greater hardening effect than either oxygen or carbon. INTRODUCTION Determination of the as-cast hardness of arc-melted titanium is a method of quality control widely used in industry. Numerous studies4/ have been made of the effect of impurities on the hardness obtained by this method. However, most of them have been based on the use of either iodide titanium or commercially pure Kroll sponge (B.h.n. >90), as a starting material.

Jan 1, 1959

By J. R. Donald

Surface and interfacial phenomena play a significant role in refractory performance. For example, the wettability of the refractory material with slag, matte, and metal influences infiltration and interfacial reactions. Yet, very little fundamental information regarding the surface properties of refractory materials and slag is available. Thus, in the present work, the sessile drop technique incorporating a high temperature furnace equipped with X-ray fluorescope was employed to investigate the surface and interfacial phenomena of fayalite-type slags on solid alumina at 1200?C. The iron to silica (Fe/SiO,) ratios employed were 1.4 and 2.0, and the oxygen potentials used were log p02 =-11 and log p02=-9 atmospheres. The contact angle between the fayalite-type slags and the alumina were determined to be relatively low, at about 16.9 to 19.6 degrees under the experimental conditions. The surface tension of fayalite slag (Fe/SiO2=1.4) at an oxygen potential of log -11 was 0.298, which agreed with the work of previous researchers. The surface tension of the fayalite was observed to increase with time. The spinel FeAl2O4. was determined to be the product of the interfacial reaction, and 8.8 to 15.8 mass percent alumina was dissolved into the slag after 40 minutes.

Jan 1, 1996

By Kathleen Lagnese, Srikanth Muddasani, Kashi Banerjee, Carla Robinson

"Mine water generated from underground coal mining operations contains both dissolved and particulate solids. Dissolved solids primarily consist of sodium, calcium, magnesium, potassium, chlorides and sulfates. When discharged to a receiving stream without treatment, these constituents create a potentially toxic environment for aquatic life.A case study is presented to discuss how a centralized treatment plant treats mine water from six locations to meet discharge limitations for chlorides. Located in West Virginia, this facility consistently achieves less than the National Pollutant Discharge Elemenation System (NPDES) permit limitation of 218 mg/L chlorides in the discharge while generating almost zero liquid waste. The dissolved solids concentration in the influent ranges between 5,000 and 10,000 mg/L, with chloride concentrations of 1,000 to 2,000 mg/L and sulfate concentrations of 2,000 to 6,000 mg/L.The mine water is treated using advanced treatment technology to produce clean water for discharge or reuse. The treatment process comprises aeration, softening, filtration, reverse osmosis (RO) reject softening, evaporation, crystallization, final effluent remineralization and sludge dewatering. The solid waste generated in the treatment process is landfilled on site. The leachate is sent back to the facility’s thermal treatment process. Because no liquid waste leaves the property, this plant is termed a zero liquid waste (ZLW) facility.The advanced water treatment system was built to meet a new 218 mg/L regulatory limitation imposed by the West Virginia Department of Environmental Protection for chlorides discharged to surface waters. The system is designed to treat a maximum flow of approximately 795 m3/h (5 million gpd) of mine water. The treatment process utilizes RO membrane treatment to achieve the effluent criteria, and evaporation and crystallization technology to manage the RO concentrate from the water treatment process. As a result, the system produces clean water for discharge while generating zero liquid waste. The effluent water can be used for industrial purposes or discharged to a receiving stream. A water impact index (WIIx) study indicated that discharge of this high-quality water into the Monongahela River watershed may improve the water quality for downstream water users. The waste produced in the treatment process, including softening sludge and salt, is disposed of in an onsite landfill. Currently, the plant is treating at an average flow of 490 m3/h (3.1 million gpd) of mine water with an average influent chloride concentration of 1,530 mg/L and an average effluent chloride concentration of 11 mg/L."

Jan 1, 2014

By T. Resende, J. Sismour

"Signs in underground mines are subject to variable airflow, which carries dust and moisture. Dust buildup reduces their visibility, hampering production efficiency and safety. Underground workers commonly must stop to clean signs in order to gauge their location, or find critical supplies or services. There are currently a variety of coating products, including dust and water repellants, available on the market that have the potential to reduce dust accumulation on sign surfaces. This paper describes a preliminary study to determine their effectiveness. The study involved a practical testing protocol using a trickle rock duster and samples cut from a clean, used road sign. Product effectiveness, under both dry and wet conditions, was evaluated based on photographic evidence by comparing changes in sign luminosity after a period of rock dust application. By analyzing the frequency of different pixel luminosities on the dust-covered samples, both uniformity of dust coverage and the total amount of accumulation was assessed. Results indicate that at least one product may reduce the amount of dust buildup on sign surfaces and increase visibility. INTRODUCTION In all underground mines, visibility of signage is critical. Signs inform miners of their location, direction toward escape routes, and location of supplies. Over time, sign surfaces can collect dust and can eventually become unreadable. The rate of dust accumulation on surfaces is often particularly high in coal mines, where both mining (e.g., cutting and drilling) and rock dusting activities can contribute significant amounts of dust to the airways. Several factors may contribute to dust buildup on sign surfaces. First, basic principles of fluid and particle flow are at play. When a fluid travels past a stationary surface, the velocity of the fluid at the surface boundary is zero. If a very small dust particle moving with air collides with a surface, it does not immediately fall off since the air velocity is zero at the sign surface. (This is the same reason that dust can collect on a rotating ceiling fan.) Further, once the collision occurs, other mechanisms may help keep the particle there – including friction that resists particle falling due to gravity, and adhesive forces due to humidity and/or static charges the particle and others already on the surface. Currently, the most common way to deal with reduced sign visibility due to dust buildup is for mine personnel (e.g., a compliance foreman, supply worker) to periodically clean sign surfaces – usually just by wiping them with a cloth. As a regular activity, this solution is inefficient; in cases of emergencies, it can also pose unnecessary risks. Application of an off-the-shelf coating to sign surfaces may represent a simple yet effective way to reduce the rate of dust accumulation. There are currently a variety of products on the market that may be suitable for this purpose, including dust and water repellants."

Jan 1, 2017

By S. Makni

Flotation is a complex process in which many mechanisms come into interaction. In this paper, an approach to model these mechanisms in order to predict size-by-size flotation performances is presented. The estimation of the collection efficiency of particles takes into account the serial sub-processes of particle-bubble collision, attachment and detachment. The model was applied to an industrial plant and yielded satisfactory results whereby the actual flotation performances could be correctly predicted. Furthermore, the flotation model allowed investigating the possibility of improving flotation performances by a split flotation feed in comparison to the actual single-stage process.

Sep 1, 2012

By G. Morin, F. Chiesa, B. Tougas, B. Duchesne, Jocelyn Baril, N. Giguère

"An aluminum A356 compressor impeller was sand cast using the Low Pressure technique. The casting was limited in size (170 mm in diameter, 1.2 kg in weight) and very intricate in shape thus making 3D mold printing particularly favorable; indeed, producing this part by the traditional pattern-core box route would involve mounting 12 cores inside the mold while stringent dimensional tolerances are required as the impeller blades are only 2 mm thick. Consequently the molds were produce on the X-One MFlex printer of Quebec Metallurgy Center - CMQ. A dozen castings were produced with different casting temperatures and filling times so that it was possible to assess under which conditions complete filling of the mold cavity would be achieved. Filling and solidification modeling allowed predicting misruns and metallurgical properties inside the A356 (AlSi7Mg04) casting.INTRODUCTION Recent advancements in additive manufacturing enable foundries to produce molds without the tooling (pattern and core boxes) necessary when conventional technology is used (Eyad, 2016). This is particularly advantageous when dealing with intricate shapes and/or when a limited number of parts must be produced within a few days rather than in 5 weeks. An additional advantage is gained when producing prototypes (Johnson, 2016) as changes are much less costly and time consuming when made on a numerical 3D drawing rather than on patterns and core boxes. 3D printing is normally economical for a small number of parts; however, if the part is not too big and very intricate in shape such as the part that will be studied in the present work, 3D printing can be economical even for an important number of castings to be produced. On the other hand, low pressure casting is a high integrity casting process in which the mold cavity is filled from the bottom via a transfer tube in which the liquid aluminum rises under the pressure applied at the surface of the melt as illustrated in Figure 1. The filling can thus be precisely controlled, eliminating the turbulence created when the mold is filled from the top (gravity casting). Also, the pressure applied on the melt during solidification results in excellent feeding of the casting when conditions of directional solidification are met. In the present work, the compressor impeller shown in Figure 2 will be sand cast by low pressure."

Jan 1, 2018

By L. Fernandes

A two level factorial study was undertaken to investigate the relative impacts of factors affecting the kinetics of polytetrafluoroethylene, PTFE, assisted pressure oxidation of chalcopyrite. A copper flotation concentrate, principally composed of chalcopyrite, was leached in 850 mL of leach solution under conditions similar to those of the CESL process. The factors manipulated were: the amount of 1/8" PTFE beads added (100 g or 650 g), oxygen pressure (690 kPa or 1030 kPa), and concentrate addition (10 grams or 65 grams). Copper extraction data, which indicated complete leaching under certain conditions, were fit using a shrinking core model from which rate constants were estimated and further used to generate a statistical model containing only the factors of significance and their interactions. Results indicated a strong positive effect of PTFE addition and a strong negative effect of increasing pulp density. A weak negative interaction between increasing PTFE addition and pulp density was attributed to PTFE/concentrate agglomeration.

Jan 1, 2014

By M. Kreuh

Crystalline Mg(OH)Cl and amorphous Mg2(OH)3C1 were successfully isolated from a hydrolyzed molten salt electrolyte sample in this work, It was found that the chemical form and crystallinity of the hydroxylchloride were controlled by the cooling rate of the molten sample when it was taken. Crystalline Mg(OH)Cl could only be obtained by cooling the molten electrolyte sample at a rate not faster than 0.6 °C/min, Upon more rapid cooling, the hydroxylchloride species precipitated as Mg2(OH)3Cl, The behavior of these solid hydroxylchlorides when contacted with fresh and non-hydrolyzed molten electrolyte at 550°C was also examined, It was found that the Mg(OH)Cl rapidly dissolved in the hot electrolyte and did not decompose into MgO at that temperature as would be expected from the literature, The dissolution rate of solid Mg2(OH)3Cl was found to be so slow by comparison that it resulted in the complete decomposition into MgO which thereafter was incorporated into the electrolyte as a suspended solid phase rather than dissolution.

Jan 1, 2004

By Yuri L. Nikolaev

The treatment of placer gold with fine gold, associated with gold-bearing sulfide minerals, heavy minerals and oxidized minerals such as manganowolframite (gubnerite) is not an easy task. In this case, this complex material cannot be treated using physical separation methods such as deep concentration and finishing, magnetic separation and solvent extraction. This technology is usually employed in gold washings finishing plant. The easiest way to recover precious metals in the form of an easy-to-sample saleable product is metallurgical treatment. This paper describes the application of pyrometallurgical processes with oxidative roasting, re-cleaning of cinders (if required) and ore-thermal smelting for producing gold bullion. Hydrometallurgical treatment of slags as an additional operation is recommended in order to maximize recovery of valuable metals. After this treatment, a barren leaching cake rich in PGM can be sold in the market. PGM can be collected as gold-silver alloy during smelting which allows the phase formation of polymetallic matte due to specific composition of fluxes. The PGM are then in the form of saleable gold bullions in the refinery.

Sep 1, 2012

By Yuemin Zhao

Pre-combustion cleaning of coal plays a key role in the process of efficient and clean utilization of coal resources. Recently, wet beneficiation of coal is predominant around the world. Nevertheless, wet beneficiation processes are limited by the increasingly serious problem of worldwide shortage of water, especially in China. Thus, it is imperative to develop efficient dry coal beneficiation techniques. Currently, several technologies such as air dense medium fluidized bed, compound dry cleaning and air jigging have successfully achieved high-efficiency separation of 50~6 mm coal. However, in recent years, a large amount of fine coal is generated as the mechanized mining technology has been progressively deployed in coal sector. Thus, it is necessary to develop efficient dry beneficiation techniques for fine coal. In recent years, many countries including China, India, Canada, Germen, and Australia have carried out many research works on fine coal dry beneficiation techniques. China University of Mining and Technology has carried out systematic researches on the introduction the vibrated energy to traditional air dense medium fluidized bed for fine coal beneficiation. This paper studied air dense medium vibrated fluidized beds (ADMVFB) for fine coal dry beneficiation. The experimental results show that the coal of <6 mm size can be beneficiated in an ADMVFB efficiently with the E value of 0.065~0.085, the separating density can be adjusted in the range of 1.45~2.2 g/cm3, and the lower limit of beneficiation can reach to 0.5 mm. Keywords: fine coal, air dense medium vibrated fluidized bed, coal separation, dry separation

Sep 1, 2012

By W. F. Baker

Location and History God&apos;s lake is in the northeastern part of Manitoba, about 400 miles northeast of Winnipeg, or about 250 miles due north of Red lake, Ontario. The lake is quite large, having an overall length of 54 miles and a maximum width of 18 miles. There are numerous islands in the lake, the largest of these, known as Elk island, being about 15 miles long and 3 miles wide in the widest part. The accompanying map (Figure 1) shows the location of God&apos;s lake and of the mine. The God&apos;s Lake area has long been regarded as promising country for the prospector, but, due to its inaccessibility, practically no prospecting was done prior to 1927. In the years 1927-1931, inclusive, a few prospectors visited the area, but no discoveries were made. In 1932, Bob Jowsey and Archie McDonald entered the area from Island lake. They first prospected in the vicinity of Knife lake, which is immediately south of the main part of God&apos;s lake, and then moved on to the latter lake, heading for the north shore of Elk island. The first afternoon on God&apos;s Lake, when looking for a place to camp on the north shore of what is now known as Jowsey island, Jowsey discovered a quartz porphyry dyke which was cut by a number of gold-bearing bluish quartz stringers. On the strength of this discovery, he and McDonald began at once to stake the Reno group of claims. Rumours of the discovery brought in other prospectors, and other groups of claims were staked to the east, along the north shore of Elk island. A second discovery was soon made by Dan McCrea on his Gold Standard claims, three and a half miles to the east of the original discovery. Staking still continued to the east, along the north shore of Elk island, and Bob Brown and Harvey McKenzie staked the Akers group on a discovery approximately two miles east of McCrea&apos;s discovery. Through the efforts of Jowsey, the Reno, Rand, Elk, and Cona groups, belonging to the original syndicate for which Jowsey and McDonald staked, were combined with the Gold Standard, Greenstone, and Akers groups, and the Company known as God&apos;s Lake Gold Mines, Limited, was formed. Several additional groups of claims were later taken over by the Company and a considerable area of adjoining ground was staked to round-out the property.

Jan 1, 1935

By József Faitli, Imre Gombköto, Barnabás Csoke, Tamás Magyar, Beáta Oláh, Sándor Nagy

"Raw materials are among the main building blocks of a growing economy. Without raw materials, no matter whether it is primary or secondary, production is not possible. Products with high added value require special materials. Recently, worldwide production of some important raw materials mainly comes from a handful of countries, for example: China (Rare Earths Elements (REE)), Russia, South Africa (Platinum Group Elements (PGE)), Democratic Republic of Congo (Cobalt), etc. In the EU as well as in Hungary, the importance of the so called 14 critical raw materials has been recognized. Within the frame of the TÁMOP-4.2.2.A-11/1/KONV-2012-0005 - CriticEL project, the Institute of Raw Materials Preparation and Environmental Processing in cooperation with the Institute of Mineralogy and Geology of the University of Miskolc are working on the exploration of the primary and secondary sources and developing innovative preparation technologies of critical raw materials in Hungary. The research work showed in this article, focused on the recovery of critical materials from LCD TVs and monitors. There are high deviations in different literatures regarding to concentrations of critical elements in displays (e.g.: indium), probably because of the differences in production year, producers and recovery technologies. During the research - described in this study - a well specified sample of quite large amount of displays had been used. The exact place and shape of the ITO (indium-tin oxide) layer were determined by SEM analysis. The applied preparation technology was developed based on the results of our investigations and by technologies found in the literature. The developed process accomplishes two main parts: the mechanical preparation (mainly the liberation of different display layers, removal of liquid crystal) and the acidic dissolution of indium."

Jan 1, 2014

By Jon C. Volkwein

Dust concentrations inside and outside enclosed cabs on several types of mining machinery were measured by the Bureau of Mines. Results indicated that properly enclosed cabs can offer significant dust protection for machine operators. Recommendations for improvements in cab technologies were discussed.

Jan 1, 1979

By Webster S. Anderson

The design, development, and testing of hydraulic props to provide a lightweight, high strength, recoverable unit is described. Modifications in design incorporating threaded components resulted in the development of a lightweight hydraulic prop fabricated from aluminum alloy tubing. This new design facilitates interchange and replacement of component parts, and the physical properties of the material are not changed as they are when welding is required. The new prop is 65,000 pounds and has a maximum load capacity of a lower weight-to-load capacity ratio than the hydraulic props now available.

Jan 1, 1967

By R. Reeves

Coal producers and utilities depend on automated coal blending systems to reduce costs and meet stringent environmental regulations. Over 30 systems installed in the United States since 1987 use on-line PGNAA (Prompt Gamma Neutron Activation Analysis) analyzers to accurately control the blending process. Experience and detailed engineering are required to integrate real-time data produced by the coal analyzer with a control system to meet demanding performance specifications. This article reviews successful installations and lists important features including interfacing analyzers with plant control systems, specifying feeders and weigh scales, and managing data.

Jan 1, 1995

By Shigehito Deki

"A new wet process has been developed for the synthesis of various kinds of oxide thin films on various kinds of substrates, even which have complex surface morphology, from aqueous solution. The process was named as the LPD, Liquid Phase Deposition, method, which has some advantages over the conventional dry processes. This process can be applied to an on-site synthesis of advanced materials in the thin film technology. In this paper, some current topics on the synthesis of the composite thin oxide films by the LPD method, are presented.IntroductionGenerally, metal oxide thin films have been made by different preparative processes such as r.f. sputtering, chemical vapor depositon, CVD, laser ablation and sol-gel method, etc [1-3]. Each method has it own advantages and disadvantage. In some cases, the process is not suitable for the preparation of thin film on substrate with large surface area or complex surface morphology, and makes the deposition apparatus complicated and expenisve. By using Liquid Phase Deposition, LPD, method which overcomes some of those problems, metal oxide or hydroxide thin film can be formed on the substrate with large surface area and complex surface morphology, which are immersed into the aqueous solution only at ambient temperature and under atmosphere without any special equipments and high energy. And also, multicomponent oxide thin films can be formed readily by mixing solutions containing the objective metal ions, because it is performed in the aqueous solution which is typically a homogeneous mixing system. This process utilizes ligand-exchange, hydrolysis, equlibrium reaction of metal-fluoro complex species, MF x (x-2n>-, and F consumptive reaction. In the aqueous solution, MFx<x-2n>-is hydrolyzed with water to release F ions by a ligand exchange equilibrium reaction as following;"

Jan 1, 2000

By Andre L. De Vegt

For the past eight years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Metal and sulfate can be removed from mine waters using two biological steps: 1. Sulfate reducing bacteria convert sulfate to hydrogen sulfide (HzS). The HzS reacts with the dissolved metals to form insoluble metal sulfide precipitates. 2. Sulfide oxidizing bacteria convert excess H2S to elemental sulfur. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove metals and sulfate as described above. The system has been operating since May 1992 treating a flow of 5000 m3/d. A test program, utilizing a large scale pilot plant, will commence in November 1995 at a copper mine in the U.S.A. to remediate groundwater contaminated with sulfate and heavy metals. Biological reactor performance and selective metal recovery will be studied. Sulfur dioxide (S00 can be removed from fluegas using a combination of scrubber technology and the two biological steps. The end product is elemental sulfur. A commercial size biological desulfurization plant has been in operation since July 1994 treating 50,000 Nm3/h of fluegas. Sulfide can be removed from mining waters or anaerobic wetlands using a THIOPAQ® Sulfide Oxidizing reactor.

Jan 1, 1996

By Vincent Tricot, Daniel Altier, Roger Storry

"INTRODUCTION The Liantang / Heung Yuen Wai Boundary Control Point (BCP) project, located in the north-east New Territories of Hong Kong, will form the seventh land crossing between the Hong Kong Special Administrative Region (HK) and Shenzhen in China (Figure 1). The BCP project comprises an 11km long dual two-lane trunk road linking the border crossing facility to the existing road infrastructure in HK and when completed it will facilitate future regional development and alleviate frequent traffic congestion at the existing Boarder control points.In December 2013 Dragages Hong Kong (a member of the Bouygues Construction Group) was awarded the 5.4km long Contract 2 section of the project, including the 4.8km long Lung Shan Tunnels, by the Civil Engineering and Development Department of the Government of the HK SAR. To overcome the difficult ground conditions anticipated along the Contract 2 section of the project the tunnels will be constructed using mechanical and drill and blast (D&B) excavation techniques together with a 14.1m diameter multi-mode Earth Pressure Balance Tunnel Boring Machine (TBM). Land constraints imposed on the project alignment require that the final 500m section at the northern end of the Lung Shan tunnels, under Princess Hill (Figure 2), takes an almost 90 degree turn towards the north. The resulting 354m radius curve restricts the sight-line of road users to below the minimum 110m at 80km/hr hence, the internal span of the tunnels needs to be increased from 12.6m, in the standard straight section, to 15.4m in this curved section to accommodate a widened shoulder which will provide the required sight-line distance."

Jan 1, 2016