Search Documents

By W. H. Ode, W. A. Selvig

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County Colo., in connection with a survey of carbonizing properties of American coals 4/ and investigations of their chemical and physical properties. 5/ The coal represented by the sample from Weld County was reported to give off combustible volatile matter at unusually low temperatures when placed on a fuel bed. The yields of tar and oil and the composition of the as from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

May 1, 1937

By Joseph Daniels

When Dame Nature shook her horn of plenty and distributed her bounties over the face of the earth, she blessed the Pacific coast with many riches, but with these she added many offsetting disadvantages or handicaps, designed, no doubt, to effect a proper balance between wealth and economy. Nowhere is the application of the law of compensation more aptly illustrated than in the matter of fuel and power resources. A glance at the map of the Pacific northwest will show that west of the Coast Range batholith we are bounteously supplied with coal, with timber, with water power, and with tributary resources of oil from California. Alaska, British Columbia, Washington, all contain large resources of coal; Oregon and California to a lesser degree, but, compensating the golden state for its deficiency in this respect, oil was placed in the treasure ,chest. Timber, of wide variety and in lavish quantity, covers the forests from tidewater to mountain slope, and within this protected watershed area flow streams which give the Pacific coast states the largest single share of the potential water-power resources of the country. Something over 40 per cent. of the total estimated horsepower of the United States is to be found in the Pacific states, and British Columbia has 15 per cent. of the total for Canada; but of this total less than 10 per cent. has been developed.

Jan 1, 1924

By Chao Li, Lim Hongxu, Yuyue Wang, Xie Yang

"A intergrated process of sulfuric acid leaching, sodium chloride leaching, lead chloride crystallization, lead hydroxide synthesis and roasting was carried out for the recovery of lead, cadmium, copper and zinc from lead smelting dust containing various metals. The results showed that the separation of cadmium, zinc and copper from dust could be obtained after sulfuric acid leaching and corresponding leaching rate were 92.12%, 90.25% and 88.26% respectively. The subsequent sodium chloride leaching carried out for lead with optimized parameters as: sodium chloride concentration 250g/L, leaching temperature 90°C, leaching time 2h, pulp density 33g/L, 0.12mol/L CaCh; The lead compounds crystallization rate reached 86.67%, and then transferred into mPbO·nH2O, the product of 98.66% ß-PbO could be obtained through roasting under 502°C. In the end, a feasible method of ß-PbO preparation from lead containing dust was put forward.IntroductionThe pyro-metallurgy flue dust from smelting lead activities are often stockpiled and pose potential environmental risks due to the heavy toxic elements, such as Pb, Cd, As, Cu, Cl, and Zn which are contained in the dust. With the rapid depletion of rich ore resources in recent years, it has become increasingly more financially attractive to recover valuable metals from previously stockpiled dust, while simultaneously reducing the potential of environmental pollution from toxic elements contained in the dust. Nowadays, pyro-metallurgical and hydrometallurgical routes or both combined methods can be developed to treat secondary materials such as lead ash, leach residues etc. By comparison the hydrometallurgical processes are often considered more eco-friendly.Some chloride leaching processes for recovering lead have been employed using either NaCl, or MgC2 and CaCl2, or FeCl3 [1] The effectiveness of the brine leaching method is based on the formation of complex metal chlorides in concentrated chloride solutions [2] Similarly, Other metals such as zinc, cadmium and copper contained in the flue dust are often treated with sulfuric acid, hydrochloric acid, ammonium solution and sodium hydroxide etc. as lixiviants [3] The metals from leach solutions thus has been obtained by precipitation, ion exchange, solvent extraction or replacement [4]"

Jan 1, 2014

By A. L. de Vegt

For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Metal and sulfate can be removed from mine waters using two biological steps: 1. Sulfate reducing bacteria convert sulfate to hydrogen sulfide (H2S). The H2S reacts with the dissolved metals to form insoluble metal sulfide precipitates. 2. Sulfide oxidizing bacteria convert excess H2S to elemental sulfur. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove metals and sulfate as described above. The system has been operating since May 1992 treating a flow of 5000 m /d. A pilot plant started operation in November 1995 at Kennecott's Bingham Canyon Utah copper mine to develop the processes for metal and sulfate removal from groundwater and selective copper recovery from leach water. The principle of the biotechnological methods, full scale experience, and an overview of the test program at the copper mine are presented.

Jan 1, 1997

By G. Song

This paper reports the anodizing voltage, gas evolution and sparking behaviors of an anodized coating formed on AZ91D in a silicate containing solution. According to their responses to an anodizing current, a four-stage anodizing mechanism is proposed. At the same time, the formed coating is characterized in terms of its microstructure, composition, thickness and corrosion performance. It was found that deposition of MgSiO3, Mg(OH)2 and MgO as well as dehydration of Mg(OH)2 are involved in the anodising process; the vigorous gas evolution accompanied by intensive sparking and the corresponding negative anodising efficiency in the later stage of the anodising process are closely associated with thermal decomposition of water due to the high temperature resulting from the intense sparking on the surface of the anodized alloy; the thickness, porosity, and composition of the anodised coating on a magnesium alloy depend on the final anodising cell voltage; and the corrosion resistance of a thick but porous coating containing more silicates appears to be more corrosion resistant than a thin but compact coating containing less silicates.

Jan 1, 2006

By Claude W. Sill

In the course of a series of investigations on vanadium deposits of the western United States, the Bureau of Mines collected many hundreds of samples for chemical analysis. As uranium is often associated with these vanadium minerals, they were also analyzed for uranium, which was pound to be absent in a large percentage of the samples. Since the usual methods for determining uranium are laborious and time-consuming it is very desirable to have some simple qualitative test that can be applied prior to a quantitative analysis to determine whether uranium is present or absent and thus save the time and expense of applying the quantitative analysis to the large proportion of samples containing no uranium. To be acceptable, the test should be specific for cranium, sensitive enough to detect small amounts of uranium, and. simple enough to make it worthwhile to apply. The available methods for detecting uranium lacked one or more of the desired characteristics. Eventually, however, a method was worked out that satisfied all the requirements. This method is probably more specific and sensitive than the usual qualitative methods for uranium, and its simplicity and speed of application make it ideal for testing samples prior to quantitative analysis.

Jan 1, 1945

By Jean E. Tilden

An investigation of several trace elements distributed among sulfide minerals from deposits located in the southeastern United States was conducted. The deposits investigated are distributed within both the Blue Ridge Province and the Piedmont Province, which are contiguous geographic provinces. Twenty five deposits were examined;' eleven in the Blue Ridge Province and fourteen in the Piedmont Province. Figure 1 shows the locations of deposits investigated. In the deposits investigated, the mineral phases examined were pyrite, pyrrhotite, chalcopyrite, and sphalerite. These phases were chosen because of their relatively widespread occurrence, although no pyrrhotite was seen in the Piedmont Province. A total of 116 polished surfaces of ores were prepared, and mineral phases were collected from these surfaces for analysis. Samples were analyzed for cobalt, nickel, manganese, lead, tin, chromium, molybdenum, and gold. A total of 372 analyses were made. Trace elements were determined by atomic absorption spectrophotometry following standard procedures. In this study, trace elements are defined as those elements which are present in the mineral but which do not affect the chemical formula for that mineral. Lead is considered as a trace element only in ores where little or no lead sulfide could be identified as a distinct mineral phase.

Jan 1, 1972

By N. Menad

The formation of the dioxins can be dependent on the quantities of carbon, hydrogen, chlorine and oxygen present in a given system, as well as on parameters such as temperature and pressure. Inadequate supply of combustion air ( incomplete oxidation ), low combustion temperatures ( incomplete combustion ), and insufficient turbulence in the combustion are factors which can favour their formation. Dioxins were produced also calatytically from chlorinated phenol precursors, non-chlorinated compounds that were chemically, and reaction of phenol with inorganic chloride. In this paper different precursors such as combination of C, H, 0, Cl, rapid formation/combustion intermediates and routes to PCDFs are reviewed, and the influence of PVC amount on the formation of these isomers is discussed.

Jan 1, 2000

By E. D. Regad, W. E. Wallace, V. Vallythan, V. Castranova, P. Hathaway, F. H. Y. Green, M. J. Keane

"Abstract—Inhaled particle contact with pulmonary surfactant in the hypophase lining pulmonary alveoli was modelled in vitro by exposing two respirable sized dusts, kaolin and silica quartz, to lecithin, a major component of pulmonary surfactant, emulsified in physiological saline. Lecithin adsorbs to the dusts upon incubation at 3TC and suppresses their cytotoxicity as measured by pulmonary macrophage and erythrocyte assays, suggesting that pulmonary surfactant provides a defence system against prompt cell membrane lysis by inhaled dusts. Subsequent pulmonary macrophage phagocytosis and lysosomal enzyme digestion of the coated dusts was modelled in vitro by incubation with phospholipase A2 for one hour. With increasing lipase activity, silica haemolytic potential was restored to native silica levels. Kaolin was retoxified to levels far in excess of native kaolin haemolytic potential. Elution, thin layer chromatography and phosphate assay of treated dusts indicate that most lecithin on silica is digested to lysolecithin and desorbed, silica retoxification being due to surface and adherent lysolecithin effects. Most lecithin on kaolin is not digested in the same time; that which is. results in adherent lysolecithin which is responsible for the kaolin retoxification. Digestion with phospholipases A2 and C together produces only weakly retoxified kaolin. Results suggest that surface adsorption properties which control the adherence of prophylactic surfactant distinguish the pathogenic potentials of quartz, kaolin and mixed dust.INTRODUCTIONERYTHROCYTE HAEMOLYSIS and pulmonary macrophage enzyme release assays show quantitatively comparable high cytotoxicities for both silica quartz and kaolin respirable sized dusts (BROWN, et al., 1980; DANIEL and LE BOUFFANT, 1980.) This contrasts with the strong potential for respirable quartz dust to induce pulmonary fibrosis and the much more limited potential of kaolin dust to do the same (MORGAN and SEATON, 1975).In an attempt to understand this anomalous situation, assays were performed on quartz and kaolin dusts incubated with dipalmitoyl lecithin emulsified in physiological saline, to simulate the initial contact of a respired dust with the pulmonary alveolar hypophase. The ability of kaolin dust to adsorb dipalmitoyl lecithin from physiological saline has been quantified (WALLACE, et al., 1975). Such lecithin treatment suppresses the cytotoxicity of both silica and kaolin to background levels (WALLACE, et a1.,1984).Surfactant coated detoxified dusts should then be phagocytised by pulmonary macrophages, incorporated into a macrophage secondary lysosome and exposed to hydrolytic lysosomal enzymes. Among these is phospholipase A2, which hydrolyses diacyl lecithin to lysolecithin. This was modelled by incubating lecithin treated dusts with phospholipase A2 in vitro to determine if the enzyme can digest the dust-adsorbed lecithin, and if the retoxification differs between the two dusts in a manner which might distinguish their pathogenicity."

Jan 1, 1988

By Culver, Richard S.

In spite of the widespread interest in rock bolt research, relatively little is known about the critical region surrounding the bolt anchor. In analyzing the stress distribution around an opening resulting from rock bolt support, it is commonly assumed that the bolt is fixed at a point far enough from the surface so that the anchor does not influence the performance of the bolt. Furthermore, a bolt anchor is assumed to per- form satisfactorily if it will hold the design load with a minimum amount of load relaxation, commonly called bleedoff. From the standpoint of the design engineer both of these assumptions are reasonable, but they ignore the fact that the extremely high stresses in the region of the anchor are capable of generating fractures in the rock. Lang estimated the bearing stresses for a slot and wedge anchor on a one-inch-diameter bolt to be as high as 125,000 psi. This paper describes a more thorough analysis of the magnitude of the stresses around the anchor and the nature of the potential fractures that might result.

Jan 1, 1968

By H. W. Manley

SULPHUR, like the minerals of coal, iron and petroleum, is one of the essential materials in our modern expanding industrial civilization. Before discussing the salient features of the production of sulphur from the Canadian sour gas, it seems appropriate to outline the historical past and probable future utilization of sulphur. The ancient Greek writer Homer spoke of its "pest-averting sulphur" and the "divine purifying fumigation". Ancient alchemists found sulphur to be a fascinating and baffling material. The discovery of gun powder in the year of 1250, and its application to the art of war a, century later, made sulphur an important commodity in the progress of mankind. The initial manufacture of sulphuric acid in the year of 1736 by the Englishman Joshua Ward, established the basis of a chemical industry that today utilizes 80 per cent of the consumption of elemental sulphur. Commercial production of the chemical soda ash ( N a2C03) discovered in 1787 by the famous Leblanc Process, in-creased international demand for the element sulphur and marks the birthday of the Sicilian sulphur industry.

Jan 1, 1961

By R. W. Stahl

Gas accumulation and dust suspension are the major safety hazards in coal stockpiling and reclaiming operations. This report presents a schedule of safety precautions and plant design features devised by the Bureau of Mines to reduce danger from these and other sources.

Jan 1, 1965

By M. Goto, T., Matsutani, T. Igarashi

"PT. Smelting was established in February 1996 as a company to· construct the first copper Smelter and Refinery in Indonesia with US$500 million direct construction cost and operate it. The plant is located in Gresik, East Java, Indonesia and 20km northwest from Surabaya, 2nd largest city in Indonesia. The site was selected due to following .advantages.1. Adjacent PT: Petrokimia Gresik, - a fertilizer company, purchases all sulfuric acid produced through pipeline.2. Facing on the seashore of the Madura Strait, it is possible to unload copper concentrate from West Papua (3,000km from Gresik) and load granulated slag to the market.3. Close to the good harbor facilities at Surabaya for export the products.4. Gresik Industrial Area has adequate infrastructure.5. Surabaya is a quite nice city to live for people from abroad.The shareholder of PT. Smelting are Mitsubishi Materials Corporation (60.5%), PT. Freeport Indonesia (25:0%), Mitsubishi Corporation (9.5%) and Nippon Mining and Metals Co. Ltd. (4.5%).The Gresik Copper Smelter and Refinery is designed to produce 200,000 tpy of copper cathode from 660,000 tpy of copper concentrates supplied 100% by 'Grasberg Mine of PT. Freeport, Indonesia in West Papua (former Irian Jaya). Other by products are 600,000 tpy of sulfuric acid, 30,000 tpy of gypsum, 509 tpy of precious metal slime and 400,000 tpy of granulated slag. These are sold to domestic and international markets.This project adopted the Mitsubishi Continuous Copper Smelting and Converting Process in the Smelter for anode casting, Contilanod process comprising Hazelett twin belt caster and a Mannesmann's travelling shear were selected. ISA stainless steel cathode process is applied in refinery. The combination of contilanod anode and stainless steel cathode ensured good cathode quality from the very beginning of start-up SO2 gas generated from Smelter is treated by Lurgi-Mitsubishi double contact/absorption acid plant. All contact. wastewater from the plant is treated in multistage wastewater treatment plant.Electricity and oxygen are ·supplied ""over the fence"" by a company which is located in the site of the Gresik Smelter and Refinery."

Jan 1, 2000

By Steve T. Laflin

Since the beginning of the nuclear era, there has never been a commercial solution for the large quantities of depleted uranium hexafluoride generated from uranium enrichment. In the United States alone, there is already in excess of 1.6 billion pounds of DUF6 currently stored. INIS is constructing a commercial uranium processing and fluorine extraction facility. The INIS facility will convert depleted uranium hexafluoride and use it as feed material for the patented Fluorine Extraction Process to produce high purity fluoride gases and anhydrous hydrofluoric acid. The project will provide an environmentally friendly and commercially viable solution for DUF6 tails management.

Aug 1, 2010

By E. Krystad, G. Tranell

"The kinetics of boron removal from liquid silicon during slag refining, as a process step in the production of solar grade silicon, has been investigated by means of small scale mass transfer experimental series at 1600°C, using a graphite crucible. The slags were SiO2-CaO based, with or without addition of approx. 19 wt% MgO. Experiments were carried out at slag-metal ratios of 1 or 2, where the silicon initially contained approx. 250 ppm boron. The metal-slag mass transfer coefficients for boron were found to be in the order of 1-3 · 10-6 m/s and were largely influenced by slag composition. The mass transfer rate was higher for the MgO-containing slag than the slags without MgO. The final equilibrium distribution of boron between metal and slag, LB, was determined to be in the order of 2.3-3.3.I. INTRODUCTIONRecent years have seen a race in industry and research aimed at obtaining a reliable metallurgical route for production of silicon for solar cells (SoG-Si) from metallurgical grade (MG) silicon. Metallurgical routes can successfully challenge the traditional chemical routes for production of SoG-Si if they generate metal of sufficient purity while being less expensive in terms of production cost and energy consumption. Efficient removal of boron is one of the greatest obstacles in the refining of silicon by a metallurgical route, because the segregation coefficient of boron in silicon makes directional solidification unfeasible; in addition, the vapour pressure of boron is not high enough for removal by vacuum refining. However, the thermodynamic properties of boron makes removal from silicon by oxidation possible, and thus the process of slag refining of silicon has been receiving increasing attention as a method for boron removal."

Jan 1, 2012

By K. H. Nimerick

Laboratory data and field tests indicate that substantial losses of valuable coal can be caused by wind erosion. Wind tunnel tests show the effects of wind velocity and particle sizing on the amount of coal lost while in transit. Different coals were evaluated to determine the variables associated with wind erosion. The erosion losses can be substantially reduced by using a binder, or crusting agent, to consolidate the surfaces of the coal into a solid mass which resists erosion. This not only reduces economic loss but minimizes pollution.

Jan 1, 1977

By P. C. Kapur

Several empirical and semi-empirical laws of comminution, which describe the relationships between the cumulative grinding energy input and the degree of size reduction of brittle solids, have been rationally derived in the time-domain in a unified manner, starting with an integro-differential equation of grinding kinetics. The analysis leads to and provides explicit interrelationships between the energy-size reduction laws associated with Kick, Rittinger, Holmes, Bond, Charles and others, and gives useful estimates of their relative merits and validity. It is shown that Holmes' expression is, in fact, a solution to the grinding equation; consequently, this classical law is compatible with the modern theory of comminution based on population balance on particulate species

Dec 1, 1971

By Clarence A. Johnson

The discovery of the Prudhoe Bay field temporarily reduced interest in the development of coal conversion processes, but interest is being re¬newed by the current energy crisis. According to M.A. Wright, Chairman of the Board of Humble Oil and Refining Company(l), the reserve in the Prudhoe Bay bield has been confirmed to be about 10 billion barrels. At first glance this appears to be an extremely large reserve which will eliminate supply problems for the United States for some time. This feeling of security is lost when one realizes that by 1980 the world will consume the reserves of a Prudhoe Bay or a Libya, or Venezuela in less than a year, based on the recent predictions of U.S. and world reserves made by Eastman-Dillon, Union Securities Company(2). Recent forecasts of U.S. demand and source of supply made by Kenneth E. Hill of Eastman-Dillon are shown in Figure 1. This forecast shows a decline in domestic supplies (excluding Alaska) after 1973, with the total domestic supply leveling off in 1975 at about 13 million barrels per day. Since the predicted demand increases from about 14 million barrels per day in 1970 to about 20 million barrels per day in 1980, about 35% of domestic consumption must come from imports or non-conventional sources by 1980. More imminent is the shortage of low sulfur fuel oil which has been created by the new, tough air pollution regulations that are basically legis¬lating eastern coals out of the market. As an alternate to importing large quantities of low sulfur fuel oil or importing and desulfurizing regular fuel oil, one of two domestic solutions is possible: stack gas clean-up or solids fuel pretreatment. Stack gas clean-up may be the cheapest approach for old installations, but fuel pretreatment has real advantages for new installations. Coal pretreatment at the mine could eliminate all solids fuel handling

Jan 1, 1972

By A. R. MacLean

This mine is situated at Point Aconi, Cape Breton , Nova Scotia, and is a replacement for the 100-year-old Princess Collie ry. It is a slope mine which is the continuation of a s trip mine operation. There are fives lopes from the surface driven with Dosco Dintheaders - this marks the first time these machines were used in North America. There are four room -and-pillar sections, each equipped with a Lee Norse HH106 continuous miner, a "Top Dog" roof bolter and two Wagner diesel Teletrams. There are also two Eimco 913 diesel LHD's , which are used for clean-up in the mines. This paper describes the mining operations of this 800,000-tpy mine which, in less than a year and a half , has been developed to the stage where four sections are producing coal at the desired rate.

Jan 1, 1978

By M. Pelegrin Rodríguez, J. Castellanos Suarez, R. Causse Miyares, A. Mosqueda Martínez, Rubén Aja

"This paper will describe the methods and the results of studies to integrate polymetallic nodule extractive metallurgy methods into existing and operating technologies or plants with the aim of reducing the capital cost of deep-sea mining challenges and to streamline the supply chain of raw materials where such opportunities exist (Moa Bay and others). It will also assess the possibility to carry out pre-industrial processing operations with productivity corresponding to pilot mining operation in the Clarion Clipperton Fracture Zone (5–10% of assumed annual production) with the use of existing facilities. The present study shows the results of high pressure acid leaching of polymetallic nodules (PN) mixed with laterite non-commercial ore. It also presents PN processing in the presence of ammoniacal tailings obtained from the Caron process. The experiments were carried out according to 24 full factorial design. The regression equations were determined for extractions of Ni, Co, Cu, Zn, Fe and Mn. The obtained results show that increasing temperature, the acid/ mineral ratio and the leaching time have a positive and significant effect on extraction of all the studied metals. However, increasing the tailings addition favors the extraction of the Co, Zn and Mn. The extraction of Fe diminishes, while the extraction of Ni is not affected. In the following conditions; 180 min, 260°C, 0.5 kg acid /kg minerals and 2.5 kg PN/kg tailing; the following extractions were achieved; 96% Ni, 90% Co, 97% Cu, 99.9% Zn, 43% Mn and 26% Fe."

Jan 1, 2017