Search Documents

By L. Yan, C. Zhou, M. Reyes

"The MINER Act requires the installation of post-accident, two-way communications and electronic tracking systems for all coal mines. One communication system which can satisfy this requirement is an electrode-based, through-the-earth (TTE) communication system, which sends signal directly through the overburden of a mine. The performance of these types of systems relies on several controlling factors such as earth conductivity, overburden depth, operating frequency, TX/RX antenna length, TX/RX offset, TX/RX orientation angle and TX current. In an effort to estimate attenuation through the earth, NIOSH researchers developed an analytic solution for the electrical field distribution of an electrode-based TTE communication system for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source. The analytic model was then validated using test data measured at an operating coal mine. The validated model can be used to optimize the operating frequency, estimate the required transmitting current, choose appropriate TX/RX orientation, and predict the performance of an electrode-based TTE system at a coal mine. INTRODUCTION One of the requirements of the Mine Improvement and New Emergency Response Act (MINER Act) of 2006 is the installation of post-accident, two-way communications and electronic tracking systems for all underground coal mines. As one of the through-the-earth (TTE) wireless communication methods available for the mining industry, the electrode-based, or linear, TTE systems establish communication by inducing a current within the earth medium by use of a pair of current probes. The resultant current is detected as a voltage by a similar set of distant probes. These probes could be an insulated piece of wire tied to two electrodes grounded at distant ends, or the grounded ends could be rails, roof bolts, or grounded electric rods. The analytical solution developed in a homogenous half-space, for this form for various transmitter/receiver (TX/RX) configurations, will be presented in this paper. The communication signals can be sent either from underground to surface (uplink) or from surface to underground (downlink). In order to achieve a successful communication link, it is necessary to understand the electric fields within the earth so that the appropriate size of transmitting antenna, TX/RX relative orientation, and operating frequency can be chosen. Hill and Wait gave the explicit forms of partial magnetic fields and partial electric fields of electrode-based TTE downlink communication with finite cable length [1]. In prior research, the E-fields of electric line transmitter were obtained for a static TX current [2] [3]. In this paper, the general and explicit forms for electrode-based TTE electric fields are developed and presented. The solutions for the extremely low-frequency (ELF) range (< 30 Hz) or DC excitation source obtained from these forms are presented. Also, factors that affect the E-field strength at RX are discussed."

Jan 1, 2017

By Thang V. Nguyen, Lisheng Shao, Gary E. Taylor

"The Community Memorial Hospital of Ventura, California, proposed to build a new state-of-the-art Cancer Treatment Center with radiation shielding walls and roof. The loose silty soils at the site had the potential to liquefy during an earthquake, which would result in significant settlement under the heavy footing loads. Treatment options included various deep foundation alternatives, as well as several ground improvement methods. The choice of wet soil mixing minimized the disturbance to the adjacent hospital during construction and potential settlement. Wet soil mixing allowed the structure to be supported on a raft foundation, meeting the stringent building total and differential settlement criteria. The authors also performed unit cell 3-D finite element analyses to evaluate the behavior of the wet soil mixing system in seismic loading conditions. This paper highlights the ground improvement design, construction, QA/QC, and the research related to evaluating the effectiveness of soil mixing for liquefaction mitigation.INTRODUCTIONThe Ventura Community Memorial Hospital proposed the construction of a new Cancer Treatment Center to replace the existing structure, which was built in 1901. The hospital complex is located in a wellestablished residential neighborhood. The soil conditions at the site of the proposed structure required ground modification to support the very heavy radiation treatment section of the building and limit settlement. Originally, 90-foot-long precast piles were considered for foundation support. Based on supplemental Cone Penetration Tests (CPTs) performed, the deepest CPT did not encounter competent pile bearing strata at a depth exceeding 30.5 m (100 ft). This could result in failure of the piles under long-term conditions, especially if hydro-consolidation occurs. The more realistic pile penetration depth would have been 36.6 to 45.7 m (120 to 150 ft). In addition, the excessive noise in association with pile driving would have been unacceptable to the community, patients, and staff of the hospital, so an alternative ground improvement solution was required.The specialty geotechnical contractor recommended wet soil mixing, an economical solution of creating a soil-cement product known as soilcrete that would significantly reduce the construction related noise and provide a more complete deep foundation for the structure.SOIL CONDITIONS AND SETTLEMENT CONCERNSThe subsurface soils were interbedded (Fig. 1) consisting of loose to medium dense silty sands, and soft to medium stiff silty clays to a depth of 30.5 m (100 ft). Groundwater was encountered at depths of 9.1 m (30 ft) and historical high groundwater was at 8.5 m (28 ft) below the ground surface."

Jan 1, 2015

By Benjamin Cebrián, María Gil, David Flores

In many occasions during the Mining operation life, blasting engineers find different and controversial results of fragmentation, dilution or wall control for the same geotechnical domain and blast design (pattern and explosive charge). Most of the times, the difference between same blast designs is not measured, not controlled. Once a blast designed is defined, the most important part of the process after that is the implementation of every step of the blast on site. Almost nobody is measuring it, controlling it, but just controlling implementation is possible to relate blast design with results in a consistent way, to optimize the full process of D&B. Controlling implementation not only per event but also to check and change trends and decision-making is paramount for optimization and saving millions of extra costs every year. The lack of resources and the hardness to manage all the info created every day in a blast make this process very tough and difficult to maintain in long term. The use of new technologies on site and software that allows a best, more consistent and continuous control of blast implementation have been proved to be the key for optimizations and cost saving. This document shows the evolution of drilling and blast digitization process, savings and trends in a mine, using new technologies that creates business opportunities and general improvement of D&B process.

By Y. Iguchi, T. Narushima, T. Shiozawa, M. Maruyama, R. Arashi

"In situ observation system for thermal oxidation using Raman spectroscopy' was constructed, and oxide films formed on liquid pure Al and Al-Mg alloys (Mg contents = 1 and 4 mass%) were analyzed at room temperature to 1273 K in dry oxygen. In situ Raman spectra of the surface of a liquid Al-:-4mass%Mg indicated the formation of MgO • AlP3 (spinel) as oxidation products, while a -AlP3 and MgO • Alz03 (spinel) were observed on a liquid Al-1mass%Mg alloy. It was suggested that the formation of MgO film affected oxidation behavior of these alloys.IntroductionLiquid aluminum alloys are cast to ingots mainly by the continuous casting process. It is well-.known that surface cracks could be caused by oxide films formed on the surface of melt during continuous casting and defects due to the film. With regard to oxidation behavior of liquid aluminum alloys, many investigations l -s have been carried out from the view point of formation of ceramic metal composites(CMC) which are expected as cutting tools and structural materials 1.2. It is very important for reasonable continuous casting and CMC formation processes to elucidate oxidation behavior of melts.Oxidation behavior of materials generally depends on compositions and properties of oxide films formed on the surface. If in situ observations of oxide films are available during oxidation, evaluation of oxide films and interpretation of oxidation mechanism could be expected. Laser Raman spectroscopy is one of the most appropriate techniques for in situ observation of oxide films under various atmosphere at high temperatures. The authors have discussed the effects of atmospheres and sample compositions on oxide film formation mechanism on Fe-Si alloy6 and SiC-B4C composite7 on basis of an in situ observation by Raman spectroscopy. In spite of many previous studies, systematic and clear explanations have never been gotten on oxidation behavior of liquid aluminum alloys. And no in situ observation has been made except for transmission electron microscopy(TEM) and X-ray diffraction(XRD)."

Jan 1, 1996

A strategy is presented for a relatively. "low-tech" means for decontamination of streams . containing .low concentrations of toxic metals. Metal ion solutions were . circulate through fluidized beds of activated carbon which support bio-films ?of bacteria .that naturally excrete exopolysaccharides. The attached &apos;biomass is shown to significantly enhance nickel, cadmium and silver extraction from dilute solutions (5- l00mg/l). By heat treating (at 300º C) the metal/biomass/carbon particles, bio-sorbed silver was subsequently fixed to the carbon surface. This approach to metal decontamination may therefore also provide a route for dispersing and fixing catalytic metal particles over an activated carbon surface.

Jan 1, 1991

By Roma T. Dec

Many industrial wastes may require preliminary processing to change their particle size, density, surface properties or flowability to become more suitable for treatment and recycle. This can be achieved by pressure agglomeration using roll presses. In the following paper an overview of various roll press processing methods like briquetting, compacting, compacting-granulating or densification is presented together with basics of process and equipment design. The emphasis is focused on major factors influencing compaction process and responsible for pressure build up and final product quality. Finally, two examples of roll press application for briquetting of steel plant wastes and compaction of alumina base catalyst tailings are introduced.

Jan 1, 1996

By A. David Miller, Douglas M. Barber

"The Rocky Mountain Arsenal was used by the military to produce chemical warfare agents and incendiary munitions for use during World War II and later by private companies for the production of industrial and agricultural chemicals. After an investigation performed in accordance with CERCLA confirmed significant levels of contamination due to the common industrial and waste disposal practices of the era and the discovery of over 300 species of wildlife inhabiting the land the Rocky Mountain Arsenal became a wildlife refuge and contamination cleanup efforts began. Three lime basins originally used to treat wastewater from the chemical production were decided to be contained in place, requiring a seepage barrier installed around the perimeter of the site to further prevent groundwater/contaminant migration. This case study will discuss the successful installation of a soil-bentonite cutoff wall around the area using deep soil mixing. Highlights of this case study will also include a discussion of the challenges faced due to construction activities performed with Level B Hazmat PPE requirements as well as added challenges brought on by the Winter season, after the project was delayed due to a positive air monitor detection for the chemical weapon Lewisite during construction of the work pad.INTRODUCTIONThe Rocky Mountain Arsenal (RMA), located just outside of Denver, Colorado, was established by the United States Army in 1942 to produce chemical warfare agents and incendiary munitions for use during World War II. Following the war, and as weapons production decreased, portions of the site were leased to private companies for the production of industrial and agricultural chemicals. The principal lessee, Shell Oil Company, manufactured mostly pesticides at RMA facilities from the early 1950s to the early 1980s.In 1984 an investigation began in accordance with the Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) and confirmed significant levels of contamination due, in large part, to the common industrial and waste disposal practices of the era. It was also discovered that over 300 species of wildlife inhabited the land in the absence of regular human activity, including a group of bald eagles, leading to the passing of the Rocky Mountain Arsenal National Wildlife Refuge Act in 1992."

Jan 1, 2015

By James T. Staley

Quenching and aging are critical processing steps used to produce precipitation hardenable aluminum alloy products. This work describes personal computer programs that employ models to predict certain properties after quenching and aging and graphically display them. One of the programs allows the user to predict the attainable strength and toughness of aluminum alloy products after an arbitrary quench. Another program simulates the changes in strength and electrical conductivity occurring during second-step aging alloy 7050-T7X products as a function of thickness, furnace temperature set point, and furnace characteristics.

Jan 1, 1993

By Corrie Pitzer

Safety performance in many companies and even industries has stalled in the last decade. Accidents rates are improving but more slowly and yet, serious accidents and fatality rates are not: in fact, these rates of more serious incidents have plateaued or deteriorating. In more dramatic cases, organizations that had ?exemplary? safety statistics, suddenly had a catastrophic or multi-fatality event occurring. Popular books such as In Search of Excellence of Peters and Waterman or Good to Great of Jim Collins created many delusional ?secrets? or recipes, to achieve great performance and yet, most of those ?great? or ?excellent? companies have now declined in their performance, some dramatically and some have fallen from grace, like Fanny Mae, a company Jim Collins identified as a ?great? one, that had to be bailed out in the latest financial crisis. These organizations share several ?delusions? about managing a business, and often, these delusions are created by academics, consultants and authors of popular books about (safety) management. More damaging however is that safety management is defined by a set of key practices or axioms: a focus on human error, compliance to rules and regulations, creating consistency of systems and actions, reacting to accidents and incidents and on prevention of those, measuring safety with performance metrics and rewarding employees on those measurements. All of these axioms contain the seeds of destruction, and they create conditions and dynamics that precede the disaster - and ironically, they are all &apos;good things&apos; we do in safety management. For example, a mere focus on safety in the business, and the measurement of it, create a culture of repression of mistakes and incidents, leading to a situation where the organization knows incrementally less and less of risks and risktaking behaviour - until the day it all coincides destructively! This paper discusses seven such safety delusions and how they impact on the views and safety management approaches. They are: ??The delusion of (risk) control, that risks can actually be identified, analyzed and mitigated. ??The delusion of compliance, that mere compliance to rules will safeguard the business ??The delusion of consistency, that standard operating procedures will ensure safe operations ??The delusion of predictability, that accidents and trends tell us everything about the risks of the future ??The delusion of human error, that people are the weakest link and that it can actually be dealt with through discipline and enforcement. ??The delusion of statistical trends, that safety is measurable with statistics ??The delusion of invulnerability, that we have achieved high levels integrity and capability to deal wit risks. Organizations that suffered catastrophes all share some or all of these delusions and this paper traces how these played a role in many disasters, ranging from the Titanic, Challenger, Piper Alpha, Bhopal, BP Deepwater Horizon and many more.

Aug 1, 2013

By Julien Favre, Akihiko Chiba, Damien Fabregue, Yuichiro Koizumi, Eric Maire

"The mechanical behavior of Co-20Cr-15W-10Ni alloy is studied by compression tests at high temperature. Microstructures after deformation are evaluated using SEM-EBSD. Significant grain refinement occurs by dynamic recrystallization for high temperature and low strain rate (T>1100°C, <0.1s-1), and at high strain rate (~10s-1). Dynamic recrystallization is discontinuous and occurs by grain boundaries nucleation, leading to a necklace structure. The nucleation mechanism is most likely to be bulging of grain boundaries. However, recrystallization occurs also by rotation of annealing twins which can bulge as well. The modeling of mechanical behavior gives a fair quantification of flow softening due to dynamic recrystallization, indicating the progress of dynamic recrystallization with deformation.IntroductionCobalt-chromium alloys are used in biomedical applications for the elaboration of implants due to their outstanding mechanical properties and their high resistance to corrosion. For stent application a large ductile behavior is required in addition to the high mechanical strength. Indeed stents have to undergo a deformation until e˜40% during their expansion [1]. Conventional Co-Cr-Mo (CCM) alloys exhibit limited ductility (maximal deformation about e˜30%) [2]. Co-Cr-W-Ni (L-605) alloy is a better candidate for stent elaboration since its fracture strain can exceed 40% (comparable to nickel superalloys (Figure 1), while it keeps high mechanical strength. In spite of the presence of nickel element in this alloy, biocompatibility is sufficient for vascular implants, therefore L-605 alloy is extensively used for heart valves and stent elaboration [3]."

Jan 1, 2012

By B. K. Mishra, Avijit Biswal, B. C. Tripathy, Abhijeet Singh, K. Sanjay, T. Subbaiah

We studied theeffect of anode substrates such as pure lead (Pb), lead antimony (Pb-Sb), and lead-silver (Pb-Ag) on the structural and electrochemical properties of electrolytic manganese dioxide (EMD). X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and chemical analyses were used to determine the structural and chemical characteristics of the EMD samples. The charge-discharge profile was studied in 9 M KOH using a galvanostatic charge-discharge unit. In all the substrates the current efficiencies were more than 99% except with Pb-Sb where it was 90%. Results revealed the nature of the substrate strongly affected the morphology of the deposited material which in turn affected the electrochemical properties of the EMD samples. XRD analyses revealed that the nature of the anode did not affect the crystal structure of the deposited EMD and all the samples were predominantly ?-MnO2, which is electrochemically active for energy storage applications. The EMD deposited on lead substrate showed superior discharge capacity of 245 mAhg-1 when compared with other substrates.

Jan 1, 2014

By Ivan L. Nichols

Tailings dumps at Mercur, Utah, contain about $7 million worth of gold in 3.5 million tons of mill tailings assaying about 0.07 ounce of gold per ton. Commercial mining and milling at Mercur ceased in 1942. To determine whether improved technology was now available that might permit economic reprocessing of the Mercur dumps, the Bureau of Mines probed for a low-cost method that would be applicable to these tailings. A composite sample prepared for laboratory studies assayed 0.062 ounce gold per ton. About 10 percent of the gold occurred as a water-soluble cyanide. Conventional cyanide leaching dissolved 32 percent of the gold, and hot, strong cyanide solution dissolved 42 percent. Results were not improved by pretreatment with acids, bases, or oxidants. After expensive preroasting, gold recovery by cyanidation was increased to 65 percent. The simple procedures were ineffective, and more effective procedures were too costly for economical processing of Mercur tailings.

Jan 1, 1970

By L. Frost

Physical Conditions Great Britain The physical conditions in the mines investigated in Great Britain are similar to those found in the mines of the Dominion Steel and Coal Corporation, with the important difference that many of the coal seams visited were interspersed by a large number of heavy faults, making the development of a continuous face operation difficult, and in many cases the life of a unit development was exceptionally short, adding to unit cost; but in spite of these difficulties, a great deal has been accomplished in the application of mechanical loading units in a number of the mines in the areas visited. The coal-bearing measures, as in Nova Scotia, consist of shales and sandstones, and in some sections mussel bands overlie the coal seams making roof conditions difficult&apos;. In several mines, the main roof consisted of weak shale bind, being held by a coal roof of varying thickness. This shale bind had a tendency to flow when the coal roof was broken. The floor, in some cases where cutter loaders were operated successfully, consisted of weak, flaky shales with very little resistance and a tendency to disintegrate into powder when broken. The depth of cover under which these mines were operating varied from 250 feet to 2,340 feet, with an average of 1,700 feet. The coal seams varied in height from 3 feet to 8 feet 6 inches, and the gradients from level to 33 per cent. The seams vary in hardness, but all-with the exception of one seam, the &apos;Morrison Busty&apos;- presented a cutting problem similar to that found in Nova Scotia. The structure and cleavage of the coal was well defined and uniform. Some of the seams visited were gassy, ?but the temperature of the workings generally was not in excess of 70°F.

Jan 1, 1948

By R. K. Mehta

An accurate, efficient and stable computation of the mill matrix function (eAt) is needed where mill matrix (A) is a real general matrix. Two important modeling cases in comminution where such need arises are: Heterogeneous comminution behavior of multi-component ores and ultra-fine grinding involving simultaneous attrition and fragmentation breakages. This paper presents the application of a novel splitting method in conjunction With similarity transformation technique in the form of "product formula" which is found to work in all cases and uses a most aggravating, yet interesting property of the matrix exponential in a restricted sense. Results are presented showing that this method can yield solution as accurate as those obtained With an analytical technique. The utility of this computational approach is demonstrated by parameter estimation analysis using a distributed component model in the liberation area through computer simulations.

Jan 1, 1992

By D. G. Chedgy

Environmental improvement efforts are focusing with increasing intensity on pollutants resulting from combustion. The high cost of removing these pollutants at the power station is well documented. Physical coal cleaning has always been and should remain the most economic method of reducing sulfur oxide emission from coal combustion. It is critical in the selection of preparation plant circuitry to consider capital and operating costs, as well as the level of sulfur reduction. This paper describes the technical criteria which must be used for efficient process selection and summarizes the cleaning systems available or in development.

Jan 1, 1990

By J. A. Chamberlain

DURING a recent trip across Canada and parts of the northern United States, the. writer examined some forty mine models. Construction -details and the uses to which the models were being put were outlined in a report to Eldorado Mining and Refining, Limited, and a specific model was proposed on the basis of the Company&apos;s particular needs at their Beaverlodge operation. It was felt, however, that portions of the report would be of some value to anyone contemplating building a mine model. For this reason, a synopsis of some of the more important aspects of the problem is presented here, together with a suggested model type that appears to have wide application. Thanks are due not only to Eldorado for permission to publish the following material, but also to the many mine personnel across Canada who allowed the writer to examine their models and gave freely of their time in discussion.

Jan 1, 1958

By Peter Krause

This report provides an overview of the worldwide photographic industry and of the applications of photography. It also covers important technological and market trends, with special emphasis on those factors which may affect the consumption of silver in the future. The text is divided into the following eight sections: 1. Principal manufacturers of silver-based photographic products 2. Major product sectors 3. Structure of the international market for silver-based photographic products 4. Silver-bearing raw materials for the manufacture of photographic products 5. Processing of photographic products: recovery of silver and recycling 6. Methods for estimating the use of silver in photographic products 7. Basic function of silver in photography and alternate image capture and recording systems 8. Brief history of photography Silver- based photographic materials are made for many applications that require different photochemical and physical response characteristics and a wide variety of formats and sizes. All of these products are laminates consisting of a surface-treated support and bonded gelatin layers. Two basic types predominate - films and papers. Films have transparent or translucent plastic supports (mostly cellulose tri-acetate and polyester), while papers have mostly a paper core coated with polyethylene resin layers on both sides (RC type). The front layer contains white titanium dioxide to provide high reflectivity and the back layer a matting agent. However, a few so-called fiber base papers are still supplied. These have a high quality paper base coated with a baryta layer ; i.e. a gelatin layer containing white barium sulfate. The manufacture of photographic film and paper supports requires special procedures and equipment, because of the severe requirements for chemical purity, optical integrity and uniformity (see Table 1 on page 10 for a list of the principal makers of film and paper supports).

Jan 1, 1992

By E. S. Peterson

The selective separations of trace metals- and organics from water are processes of importance to industry. The application of a new metals capture technology coupled with polymer membrane technology has proven to be one avenue to accomplish such selective separations. The polymers used in these studies are polyphosphazenes. Polyphosphazene polymers consist of an alternating backbone of nitrogen and phosphorus atoms. The polymers have high thermal and chemical stabilities. Experiments at the Idaho National Engineering Laboratory demonstrate that polyphosphazene membranes coupled with Chromato Chem,"Chelation Chromatography" process are capable of removing both chlorinated hydrocarbons and metal ions from process streams. These results point to a wide range of potential industrial and environmental applications for such systems. Data will be presented which show the efficiency and selectivity of separations, postulated separation mechanisms, and the initial designs of industrial demonstration units which are currently under construction. Parts of this work have been performed under a Cooperative Research and Development Agreement (CRADA) between ChromatoChem, Inc. and Idaho National Engineering Laboratory (INEL). The work at INEL was been sponsored by the United States Department of Energy&apos;s Office of Industrial Technologies

Jan 1, 1995

By Y. Tanaka, M. Maeda, S. Suzuki, C. Tokoro, T. Kato, K. Muto

Boron (B) co-precipitation was investigated with ettringite to establish a cost efficient method of removing B from acid mine drainage. For 25 mg/L of B solution, most appropriate pH for B removal was pH 11.5. The most appropriate amount of reagent for B removal within Japanese effluent standard (10 mg/L) was B:Al:Ca:SO4 = 1:3:9:4.5, which corresponds to the composition of Ettringite (Al:Ca:SO4 = 2:6:3). The effect of silicate, carbonate and temperature on efficiency of B removal is important as groundwater and hot spring water are often contaminated. When silicate and carbonate are present, more Al and Ca salts are needed for B removal since some aluminum and calcium precipitate with silicate and carbonate as kaolinite and calcium carbonate. These precipitates do not contribute much to B removal. As the temperature raised, the most appropriate pH for B removal decreased. B removal became less efficient as monosulfate precipitated more rapidly as ettringite.

Jan 1, 2015

By R. L. Brown

The burning sulphide ores in the Sullivan Mine generate sulphur dioxide gases. This paper is concerned with a description of the environmental impact of SO2 on air quality in the mine and on the surface in the vicinity of the mine. As a result of surface caving, SO2 has been able to vent to surface and winds have carried it into one residential area of Kimberley. Monitoring practices are described.

Jan 1, 1977