Search Documents

By N. Krishna

The utilization of Electrochemical Impedance Spectroscopy (EIS) in conjunction with Atomic Force Microscopy (AFM) is a powerful surface characterization technique to study the role of sulfur formation during acidic oxidation of chalcopyrite. It has been established that the chalcopyrite dissolution kinetics is controlled by the formation of passive sulfur layer during leaching. The objective of the study was to characterize the intermediate sulfur layer formation at different oxidation conditions in acidic solution. The chalcopyrite samples were subjected to anodic oxidation and the oxidation process was analyzed using impedance spectroscopy. The sulfur growth on the chalcopyrite surface during oxidation was further analyzed using Atomic Force Microscope for sulfur roughness and grain size, peak height and sulfur growth.

Jan 1, 1999

By Osarnu Inoue

In Mitsubishi Continuous Copper Smelting and Converting Process, smelting, slag-matte separation and matte converting are continuously carried out in series in three furnaces connected by launders. As a result of this operational configuration of the furnaces, influence of the change in operating condition in upper stream, such as variation of feeds in the smelting furnace, propagates to down stream with some delay. In order to achieve stabler operation, process control algorithm based on the dynamic characteristics of each furnace would be very effective. In this study, the dynamic process simulation model was developed for the smelting furnace. The model consists of two mathematical modules, i.e. the thermodynamic module and the mixing module. The calculation results using operating data obtained at Naoshima Smelter showed good agreement with the actually observed change in temperature, composition and flow rate of matte and slag at the outlet of the furnace. In addition, operation parameters such as reaction efficiency of oxygen and coal, dead volume of melts were estimated.

Jan 1, 1999

By John J. Reed

Since the beginnings of, the human struggle for survival and improvement, mining has been one of the basic endeavors of life. Until relatively recent times it was classed as an art. Now we are at work trying to, raise mining to the level of an engineering science where it belongs if we are to prosper. It should be self-evident that this goal can be attained only through industrial progress: based on education and research. It is true that our industry, left to itself, will develop a few new ideas and techniques through the years. However, we mining' engineers are relatively few in number compared to the other disciplines, and the rate of our improvement by such "accidental" discoveries is simply tooslow to keep pace with the rest of our technical civilization. It will be evident in the remarks that follow, that the rapid development of mining education, research, and the industry are extremely interdependent, and will be largely controlled by the amount of cooperation, support, and cross-fertilization that can be developed among all three.

Jan 1, 1961

By Ibrahim Alp, Ersin Yazici, Oktay Celep, Haci Deveci

Low extractions (<80%) in cyanide leaching impose the application of physical and chemical pre-treatment methods (e.g., ultra-fine grinding, roasting, alkaline leaching) prior to cyanide leaching to achieve acceptable recoveries. The effectiveness of the selected pre-treatment method is linked intimately with inherent mineralogical properties of ore. In this study, a refractory silver ore assaying 145 g/t Ag was subjected to various pretreatment tests in an attempt to eliminate its refractoriness. Direct cyanidation of the ground ore (d80: 65 µm) produced a low silver extraction of only 29.5% over 24 h indicating its high refractoriness. Previous studies have shown that silver occurs mainly as Sb/As containing sulfide minerals such as pyrargyrite (Ag3SbS3), tetrahedrite (Cu12Sb4S13) and proustite (Ag3AsS3), which do not respond well to cyanide leaching. Also, silver-containing minerals are closely associated with and/or encapsulated in other mineral phases that can restrict the contact of cyanide with silver. Therefore, alkaline leaching (using 3 M of Na2S, NaOH or KOH solution) and ultra-fine grinding as pre-treatment methods were tested to improve the extraction of silver. All the alkaline leaching tests were carried out for 3 h at800C. Neither NaOH nor KOH leaching produced the desired effect on the extraction of silver (i.e., ~30%). Even, a sharp decrease in the extraction of silver (i.e., 10%) was observed in Na2S leaching. On the other hand, ultra-fine grinding (UFG) (d80: 3 µm) substantially improved the extraction of silver in cyanide leaching (95% Ag at 24 h after UFG). It can be inferred from these findings that the refractoriness of the ore is essentially physical in character (i.e. the encapsulation of silver presumably in non-sulphide minerals such as barite and quartz).

Jan 1, 2014

By Dwayne D. Tannant

This paper presents a new mining concept for oil sands called ?hydraulic underground mining of oil sands? or HUMOS. While this mining method is still at the conceptual stage it has great promise to allow extraction of bitumen from areas that are currently uneconomical or technically infeasible using surface mining or steam assisted gravity drainage. HUMOS is founded on a combination of recently proven technologies such as directional drilling, water jet cutting of oil sands, slurry transportation, cold water extraction of bitumen, and thickened tailings. One key component in the mining concept is the caving of oil sands and the creation of an underground cavern. Scaled-down physical models will be designed and built to demonstrate water jet cutting, cave development, and insitu primary bitumen separation. These will be used as a &apos;proof of concept&apos;. On-going research will establish and prioritize issues that need to be resolved, outline key areas where further research is needed, foster establishment of research teams to divide and conquer the important questions, and create framework for future coordinated research efforts.

May 1, 2001

By Fumitaka Tsukihashi

Increasing amounts of steel scrap are being used as resources for steelmaking. Therefore. there has been a growing interest in the removal of handful tramp elements such as antimony, zinc, tin, arsenic, bismuth, lead and copper from the molten steel. The problem that should be solved is the economic removal treatment of residual tramp elements in the steelmaking processes and the production of high quality steel by reducing the effect of the contaminated tramp clements and satisfying the environmental regulations. In this paper, the available thennodynamic data of the residual tramp elements in the molten steel are summarized and the possibility of the removal of residual tramp elements from the molten steel is thcnnodynamieally estimated.

Jan 1, 2003

By T. D. Ralston

This Bureau of Mines report presents a mathematical model for heterogeneously catalyzed chemical reactors operating under turbulent conditions. The model includes reaction kinetics on the catalyst surface as well as diffusion of the reacting components within the reactor. Three applications of the model to tube-wall methanation reactors are discussed. The first application is a computation of catalyst activity from measured reactor data. This result is then used in a reactor sizing problem and a problem of reactor simulation with recycle. In addition to the reactor model, a novel approach to solving the recycled reactor problem is given.

Jan 1, 1974

By Philippe V. Scheers

Polycrystalline gold, glassy carbon and gold-activated glassy carbon electrodes were compared for the production of hydrogen peroxide by the cathodic reduction of dissolved oxygen. Gold was deposited on glassy carbon by sputtering with a sputter coater and by electrodeposition from a diluted KAuCl4 solution using short potential steps. The sputtered gold particles were not adherent enough, but there were no adhesion problems with the electrodeposited gold particles. The gold coverage of the glassy carbon surface could be varied by applying a different number of potential steps. The overpotential for the electroreduction of oxygen to hydrogen peroxide decreases with increasing gold coverage of the glassy carbon surface, and for gold coverages exceeding about 16 %, the overpotential is close to that observed on polycrystalline gold.

Oct 1, 2003

By V. G. Medina

The 15 000 t/d La Coipa mine initiated operation in July of 1991. The complex consists of a conventional, open-pit mining operation and a mill employing cyanide leaching with Merrill-Crowe gold and silver recovery. The process plant includes a primary crushing circuit, a 15,000 t (live) covered stockpile, a semi-autogenous mill/ball mill/crusher or SABC grinding circuit, a leach circuit, a belt filtration/washing circuit, a zinc precipitation circuit and a "dry" tailing disposal system. The process plant is described in detail with major design considerations used in the selection of the processes and equipment. The unique methodology employed in the disposal of the filtered tailings is also described.

Jan 1, 1992

By S. Esfahani, M. Barati

Heat recovery from blast furnace slags is often contradicted by another requirement, to generate amorphous slag for its use in cement production. As both the rate and extent of heat recovery and slag structure are determined by its cooling rate, a relation between the crystallization kinetics and the cooling conditions is highly desired. In this study, slags with different basicities were studied during non-isothermal cooling. Their continuous cooling transformation (CCT) diagram were plotted and compared with each other. Then, a mathematical model was developed that predicts the amount of crystallization during cooling. The results were validated by experiments performed by Single Hot Thermocouple Technique and image analysis. A second mathematical model that calculates temperature history of slag during its cooling was coupled with the above model, to allow optimizing the slag/air ratio for both heat recovery and slag glass content.

Jan 1, 2015

By Soumitro Nagpal

Bacterial oxidation of a pyrite-arsenopyrite-gold ore concentrate was carried out in .14-liter continuous-flow stirred-tank reactors (CSTR). Oxygen and carbondioxide consumption rates mineral dissolution rates, and bacterial concentrations were measured at various steady-state residence times and with 6, 11, and 16 wt.% solids in the feed slurry. A sharp optimum in biooxidation rate .was found at a residence time of approximately 40 hours for operation at each of the three pulp-densities. Biooxidation rates increased consistently. with increasing pulp density. Cell washout accompanied by negligible biooxidation rates was found to occur at a residence time of approximately 20 hours. Mineral&apos; oxidation was found to be strongly dependent on bacterial activity. Arsenopyrite was found to be preferentially oxidized? at the higher Pulp densities.

Jan 1, 1991

By Paykan Safe

Computational Fluid Dynamic (CFD) modeling provides a powerful tool to assist with the design of ventilation and fume control systems in smelters and other high temperature metallurgical facilities. For this paper, this tool has been used to analyze the off-gas flow patterns exiting the mouth of a Peirce-Smith converter into a water-cooled hood and drop out box. The effects of various process and physical plant design parameters on process gas and fume capture and potential build up on the converter hoods was examined, and the optimum design and operating parameters were determined.

Jan 1, 2000

By R. J. Bridwell

Acid mine drainage (AMD) occurs in high sulfur coal and heavy metal mining environments. We show remediation methods using 3D numerical ground water flow models and chemical kinetics of pyrite oxidation for acid leaching of pyrite during air and ground water flow. A recently developed numerical model couples air and water flow with kinetics of iron-reactive bacteria, oxygen transport, specific chemical reaction rates, and pyrite oxidation to calculate migration control of pollution. A model is presented which considers diminution of acid mine drainage in pyrite rich ore bodies by raising the potentiometric surface through a vadose zone to reduce acid mine drainage. A ground water model is presented of an initially saturated mountain, containing an adit, with a sloping ground water table. Ground water recharge consists of snowfall and normal precipitation. Simulations indicate that the historically open adit creates a desaturated mountain above the adit. Significant air saturation ranging from 10-90% oxygen can occur to depths of the adit (-270 m). Remediation consists of plugging the adit, which fill s adit and mountain with water from recharge. Plugging the adit required <10 years for resaturation and rise of the water table in the mountain.

Jan 1, 1994

By Takahiro Miki

In order to use metallurgical grade silicon (MG-Si) as a starting material for solar cell, phosphorus has to be removed from silicon because phosphorus is a n-type dopant. On the other hand, silicon, ferrosilicon, and silicomanganese are widely used as deoxidizers in steel refining processes. Since most of the phosphorus introduced during the deoxidation process is brought into final products, it is important -to lower the phosphorus content of these alloys. Hence, thermodynamics of phosphorus in such metals is important for the evaluation of dephosphorization processes. In the present study, thermodynamic properties of phosphorus in molten Si-P alloys at 1723- 1848K and those of Si-Fe-P and Si-Mn-P alloys at 1723K have been determined by equilibrating respective metals in a controlled phosphorus partial pressure. The results are expressed as follows.

Jan 1, 1998

By Billy Rosseau, Mike Cammack, Richard O’Meara, Gustavo Azpilcueta

During the summer of 2014, the U.S. Army Corps of Engineers (USACE) sought proposals to vastly improve and expand the small boat harbor in Valdez, Alaska. It would be a multi-year project, and construction was scheduled to begin in the spring of 2015. One aspect of the project was the construction of a 3,100 feet (1000 m) rubble-mound breakwater to protect a mooring basin. An estimated 208,500 tons (190,000 t) of rock, ranging in size from 160 to 3500 lbs (73 – 1600 kg), were needed to build the breakwater. The Glacier Point Quarry was selected as the rock source due to its proximity to the project and the quality of the rock meeting all of the USACE rock standards.

Jan 1, 2017

By M. K. Yelloji Roa

Effect of conditioning with Thiobacillus ferrooxidans on the floatability of sphaierite and galena has been determined in this work. The flotation behavior of the conditioned minerals clearly shows that such bacterial conditioning does produce marked modification of their surfaces. The variables affecting the surface modification and thereby the flotation response of the minerals were found to be cell concentration used for bacterial conditioning, the period of biotreatment and the pulp density. Importantly, while the enhancement in flotation obtained due to sulphuric acid treatment was retarded by biotreatment in the case of galena at all cell concentrations due to electrochemical effects, such decrease occurred in the case of sphalerite only at cell concentration sufficiently high for their attachment to the mineral surface. The effect of bacterial conditioning has significant implications to the differential flotation of sphalerite and galena. Mechanisms responsible for the modification of the surface properties of these sulphides due, to bacterial conditioning are discussed.

Jan 1, 1991

By H. EI-shall

Bench top centrifuge is used to study the consolidation behavior of phosphatic clays. A mathematical model (based on first order kinetics) is developed to describe the relationship between the void ratio (at any time) and the effective stress. Permeability of the sediment as a function of the void ratio is also described. The obtained data are compared with that obtained by other consolidation testing methods. Centrifuge results indicate that consolidation data may be developed in a short period of time (hours) as compared to days or weeks when other techniques are used.

Jan 1, 1995

By J. Frostiak

The Campbell gold operation of Placer Dome Inc. produces an arsenopyrite-sulphide concentrate which must be treated either by roasting, biooxidation or by pressure oxidation to obtain high gold recoveries. Pressure oxidation is a proven process and has the inherent advantage of meeting the stringent environmental regulations in the province of Ontario. A comparison of biooxidation and pressure oxidation was completed early in 1990 and the latter was selected by Placer Dome as the preferred process for replacement of the roasters. The commercial plant design was based on technology supplied by Sherritt Gordon and in July of 1991, the existing roaster operation was shut down and a new pressure oxidation plant was commissioned. The following summary describes the start up of the new facility and presents typical operating data.

Jan 1, 1992

By Rob Farnfield, Ben Williams, Bob Woolley

This paper outlines how drilling safety standards are being driven forward in the United Kingdom’s surface mining and quarrying industry with developments in equipment, procedures and competence.

Jan 1, 2010

By L. P. Meade

The need to feed an established talc mill from a crude are source located closer to the mill prompted the drilling in 1986 of a previously mapped talc-carbonate deposit. This talc-bearing rock had never been considered as a potential source of crude talc are because of the high carbonate content and other deleterious minerals that were observed in outcrops. Selective mining, in-pit grade control and creative processing has allowed this deposit to be developed into an orebody. By definition, an orebody has to be a source of positive cash flow. With industrial minerals, this is determined as much by market acceptance as by are tenor.

Jan 1, 1992