Search Documents

By J. H. Nead, T. S. Washburn

The grades of commercial steel produced in large quantities can be divided into two general types from the standpoint of ingot structure— killed and rimmed. Killed steel covers a wide variety with carbon contents throughout the range of the steel portion of the iron-carbon diagram, and is the kind usually used in the production of alloy steels. Rimmed steel is normally associated with carbon ranges under 0.30 per cent, and is not yet used to a large extent in alloy practice, except for copper-bearing steels. The fundamental differences in the ingots made from these two types of steel can be seen most easily in Figs. 1 to 7. In the rimmed ingot shown in Figs. 5 to 7 there are two lines of blowholes approximately parallel to the sides and coming together at the top and at the bottom of the ingot. In the killed ingots shown in Figs. 1 to 4 these blowholes arc not present. Also, the rimmed ingot has no well defined pipe, as compared to the deep pipe on the killed ingots, and there are numerous primary blowholes in the lower portion of the rimmed ingot perpendicular to the surface and close to it, while on the killed ingot there are no blowholes of this type in the ingot shown in Fig. 1 and very small ones close to the surface in the lower part of the ingot shown in Figs. 2 to 4. With respect to the presence of pipe and the primary blowholes, the structure may vary considerably in both rimmed and killed ingots, therefore these cannot be considered as fundamental structural characteristics differentiating the two types of steel. The primary blowholes in rimmed ingots may be much less pronounced than those in the ingot shown in Figs. 5 to 7—as, for example, in "ingot iron," which is entirely free from them. An example of a cross section of an ingot-iron ingot is shown on page 16 of "Research and Methods of Analysis of Iron and Steel," published by the American Rolling Mill Co. (1920). A certain amount of pipe may also occur in rimmed ingots, though it is normally porous and not as well defined [or deep as in the killed ingot of Fig. 1. In killed ingots, primary blowholes may occur near the surface, as in Figs. 2 to 4, and

Jan 1, 1937

By W. P. Sykes

In connection with a study of tungsten steels, Honda and Murakamil reported an investigation of the system iron-tungsten. This report included a tentative equilibrium diagram, photomicrographs of various alloys in the series, and qualitative measurements of hardness and magnetic properties. The present investigation originally had as its object the study of the hardness and tensile properties of a series of carbon-free iron-tungsten alloys. But, as the work progressed it became evident that the system possessed other features of interest, so the scope of the investigation was enlarged. Materials The iron powder used in preparing the alloys was obtained as follows : Iron oxalate was precipitated from a ferrous-sulfate solution by the addition of a solution of oxalic acid. This oxalate, after thorough washing, was ignited to iron oxide, which after reduction in hydrogen at about 1000" C. yielded iron powder containing but about 0.2 per cent. iron oxide and about 0.005 per cent. carbon. Tungsten metal in the form of powder, such as is used in the manufacture of filaments for incandescent lamps, was the other constituent. This material analyzed 99.8 per cent. tungsten and contained no carbon. The metal powders, in the desired proportions, were mixed by tumbling and formed, under pressure of 20 tons per sq. in., into rods 3/8 by 3/8 by 10 in. To form the alloys without contamination, sections of the pressed rods were placed on alundum slabs and heated in an alundum tube wound with a tungsten resistor and packed in heat-insulating material. While the resistor was heated, a stream of hydrogen was continually passed through both the tube and the case containing it. The tungsten winding on the tube, as well as the material heated within the tube, was thus protected from oxidation. Such a furnace will operate constantly for several days at temperatures up to 1500' C. and for shorter periods

Jan 1, 1926

Develop quieted, hand-held pneumatic percussion drills that can replace standard hand-held drills in many underground mining applications. The Problem Percussion drills are the noisiest machines used in underground mines; noise levels of 115 to 120 dBA are common, requiring the use of hearing protectors and limiting the time a miner is permit-ted to operate the drill during an 8-hour shift. Hand-held pneumatic percussion drills pose a particularly difficult problem because the operator cannot be isolated from the noise source (e.g., an acoustical cab), and alternative technologies for drilling roof bolt holes and blastholes in tight quarters are not readily available.

Jan 1, 1984

By Tobias Hens, Andrew Frierdich, Joël Brugger

The rapid advancement of green technologies in recent years is closely tied to an ever- increasing demand for raw materials. Innovative forms of zero-emission transportation and sustainable power generation will require a variety of traditional metals such as Ni and Co, but also many non-traditional metals (e.g., REY). Many of these elements are known to be highly enriched in deep-sea ferromanganese (Fe-Mn) nodules and crusts. However, unlocking these metals from their deposits through metal processing is – aside from deposit exploration and production – expected to be a critical component that will affect the overall economics of the marine mining value chain. Hence, research and development of tailored metal processing solutions which can target specific metals of interest in Fe-Mn nodules and crusts, is required. Dynamic mineral recrystallization (DMR) of Fe-Mn oxide phases is a geochemical process that may have notable potential for hydrometallurgical applications. We have recently demonstrated that Ni can effectively be cycled between deep-sea Fe-Mn nodules and crusts and solutions through dynamic mineral recrystallization. DMR occurs in nature as abiotic background process during biogeochemical Mn cycling when dissolved Mn(II) is in direct contact with Mn oxides. Trace metals which are incorporated in the Mn host phases, are cycled between solid phase and solution via coupled dissolution (trace metal release) – reprecipitation (trace metal incorporation) mechanisms.

Jan 1, 2018

By B. R. T. Simoneit

The formation of petroleum is normally thought of as a geologically lengthy process, involving the accumulation of organic matter, its gradual burial, diagenetic breakdown via geochemical reactions, maturation, heating within a 75-150'C "oil window" induced by normal geothermal gradients in the subsiding basin, and slow product migration into structural traps (Tissot and Welte, 1984, Hunt, 1979). The entire process can take millions of years and, indeed, most oil reservoirs probably formed in this manner. How-ever, today in sedimented, submarine rift basins (Fig. 1), Cl to >C40 hydrocarbons with the chemical and physical properties of crude oil are forming in demonstrably much shorter time by rapid thermal maturation of immature organic matter in hydrothermal regimes that are unusually high for sedimentary basins (Brault and Simoneit, 1988a, b; Didyk and Simoneit, 1988; Kawka and Simoneit, 1987; Peter et al., 1988; Simoneit, 1983; 1984; 1985a,b; 1988; Simoneit et al., 1984; 1987; 1988).

Jan 1, 1989

By Dwight D. Trueblood

The Benthic Impact Experiment (BIE) is designed to address the effects of sediment redeposition prior to the commencement of commercial mining. The experiment is being conducted in collaboration with Russian scientists from the Yuzhmorgeologiya Association aboard the R/V YUZHMORGEOLOGIYA. Sediment resuspension and subsequent redeposition during manganese-nodule mining is predicted to be one of the primary impacts on benthic communities living on the abyssal seafloor. The redeposition thicknesses that will cause significant faunal mortality in the deep sea are unknown. Sediment redeposition could adversely affect abyssal benthic communities through entombment, or through starvation caused by food dilution and obstructed feeding. This spring NOAA conducted the main portion of the BIE experiment, blanketing the experimental area with varying thicknesses of sediment using the Deep Sea Sediment Resuspension System (DSSRS). The DSSRS was conceived by NOAA scientists, designed and built by Williamson and Associates, and is the critical piece of equipment used to generate the controlled sediment redeposition environment on the 4800-m deep abyssal plane. The DSSRS consists of an 1800-kg sled, 4.8 m long, 2.4 m wide, and 2.2 m high. The sled was towed and powered using an 8,000-m, 26-mm single conductor cable having a 3,000 VAC capacity. As the sled was towed across the bottom, mud was ingested through two rear-facing, 45-cm wide intakes using two 7.6-horsepower pumps, and discharged 10 to 20 m above the bottom through two 20-cm diameter riser hoses. Each pump was instrumented with optical backscatter sensors providing real-time information about the discharge concentration.

Jan 1, 1992

Objective: To enable mine operators and mine inspectors to make quick and accurate measurements of the explosible nature of coal and rock dust mixtures.

Jul 1, 2008

By C. A. Holley

Agitative agglomeration is a rapidly expanding field related to many chemical processes. This paper reviews many processes and the particular type of agitative agglomeration that is utilized with each. Many new innovations to produce granular products in place of powder are explored. The operation and theory of the many types of agitative agglomeration equipment is reviewed.

Jan 1, 1988

By Fred N. Kissell

The new MSHA diesel rules have stone mine operators looking hard at pos¬sible upgrades to their ventilation systems. There are existing methods to reduce diesel engine emissions (MSHA, 2001)(Head, 2001b),but many operators will decide that a ventilation upgrade is necessary is well. NIOSH hay several stone mine ventilation projects underway, but in the meantime a good information resource is the work done by the U.S. Bureau of Mines in the 70's and 80's on ventilation for oil shale mines. The Bureau conducted this research because oil shale mines were projected to be gassy and would, therefore, require a lot of ventilation air. The focus of this oil shale work was on the use of jet tans for lace area ventilation, and on stoppings that would he low Lost and leak-tight. The work also considered changes in mine design to reduce the number and size of stoppings. The findings are still applica¬ble to stone mines.

Jan 1, 2002

Drilling through unconsolidated material I need to drill blastholes through a mix of consolidated and unconsolidated material. This material is hung up in an underground ore pass. The total length of the holes would be approximately 200 feet. We have attempted to drill through the material with conventional ITH drilling, but were unsuccessful. Does anyone have a suggestion? I am more than willing to bring in a contractor to do the job, if they have solid experience with this type of problem.

Jan 1, 2011

By J. W. Rinard

This paper is intended to introduce "non engineers" to one of the more misunderstood pump performance parameters, NPSH (Net Positive Suction Head). This basic presentation and resultant review should provide a practical understanding of NPSH and what its importance is to pump operation and reliability.

Jan 1, 1996

By Oliver Bowles

"A New Mica Company in China A report has been received from the American Consulate at Chungking, China, to the affect that a new company has been organized to operate a mica mine north of Ta-chien-lu, in the province of Ssu-Chuan. The company, which is entirely under Chinese management and control, has a working capital of $10,000. While comparatively new, the mine has been worked before, and apparently with some success. The mica is said to be of good quality. It is claimed that the deposit will supply a limited amount of mica that will cut in pieces a foot square or over, and larger quantities of smaller sizes. The chief difficulty is transportation, for it is reported that a ten days' journey, part of it over mountain trails, will be necessary to transport the mica from the mine to Yachow, the nearest practical waterway. It is probable, therefore, that the output of the mine will be limited.Necessity for Careful Trimming and Grading of MicaA recent report to the Department of Trade and Commerce, Ottawa, Canada, by Acting Trade Commissioner C. G. Venus, London, England, contains information which is of vital interest to mica producers in the United States. It is pointed out that mica exports from Canada to England show a gradual decline dur¬ing recent years, the figures being as follows: 1913- 1,383 cwt: 1914 - 1,225 cwt: 1915 - 1,864 cwt: 1S16 - 879 cwt: 1917 444 cwt: 1918 - 480 cwt. Shipments from India to England, on the other hand, show a steady increase from 40,178 cwt. in 1913 to 66,401 cwt, in 1918."

Jan 1, 1920

By L. I. Hewes, Joseph W. Roe

A graphic solution of Kutter's formula for the flow of water has been worked out by Dr. L. I. Hewes in connection with his course in Graphic Computations, given in the Sheffield Scientific School, Yale University, which may be of interest to those who deal with canals, flumes and streams. 1.811 0.002811 , 41.66+ -n+-S- I Kutter's formula, V= - n 0 .00281 78- 1+(41.66 + 0.00281)7B781 is probably the most accurate of those proposed determining the flow of water. But it is extremely cumbersome, and if many calculations are to be made their solution becomes drudgery. The purpose of this chart, Fig. 1, is to furnish a rapid solution, sufficiently accurate to be well within the limits of the observed data. The chart consists essentially of three parallel scales, one for the mean velocity, V, one for the hydraulic radius, R, and one for the slope; a diagonal line, not graduated ; and a set of curves for the various values of n, the factor which involves the na-

Jan 1, 1910

By AIME AIME

T HE new Secretary of the Institute has been asked to address the members through the medium of MINING .AND METALLURGY, and it is perhaps well that he should do this at the first opportunity after his election. The duty of the Secretary, as the present incumbent understands it, is that of attempting to carry on the functions of the Institute in a manner that 'will tend to make it serve its most useful purpose. What is its most useful purpose or purposes? This was concisely answered by Dr. Joseph W. Richards in the June issue of MINING AND METALLURGY under the title "Why is the Institute?" And yet its most useful purposes are not 'fixed ideals or definitely determined things, they vary from year to year, changing with the development of the nation, conforming to needs and anticipating future requirements. Many men of many minds cannot always see eye to eye. The ideas or ideals of one may seem trivial to another, an obvious necessity to one is an entirely useless activity to the minds of others. A number of the activities upon which the Institute is now engaged might have been looked won, a few years since, as uncalled for, unnecessary, and un- desirable. The participation in public affairs was one of these questions. The publication of three volumes in one year may have been a questionable thing to do, but it was an achievement. A monthly magazine that will pay for itself by carrying the Institute's message to its members has its detractors, and yet to many members it seems one of those things that are quite worthwhile. Fortunately, we have a large membership, and fortunately the majority of an intelligent body of such size is apt to have in common many ideas that are right and proper. If these ideas can be ascertained

Jan 1, 1921

By F. C. Bond

History The breaking and shaping of rock was one of man's earliest occupations. In the Paleolithic Age long before the dawn of history, arrow¬smiths and the makers of stone axes, hammers, knives, scrapers, spears, and borers were highly respected members of society. In early historical times stones for building blocks, roads, and city walls were shaped by slaves and convicts, who also did most of the mining. However, great artists erected beautiful stone sculptures, while gifted architects planned imposing temples and monuments. Until well into the 19th century nearly all rock was broken laboriously by hand. The small rock required by John MacAdam for his macadamized roads in England in the 1820s was produced by women and boys seated alongside the roadside with hand hammers and legs wrapped with rags. Eli Whitney Blake, a nephew of the Eli Whitney who invented the cotton gin, developed the first successful jaw crusher before 1870. The gyratory conical crusher soon followed. Comparative tests established its large capacity advantage over the jaw crusher, as well as its greater cost for a given feed size. Both types have been in use for more than 100 years. Crushing rolls appeared before 1900. Thomas A. Edison made very large diameter rolls which were excessively long; they failed because of shaft deflection. Various types of disk crushers and edge runner rolls appeared about this time. The older methods of reducing rock were adaptations of other processes. The stamp battery of dropping weights effected crushing by simulating heavy hammer blows; the much earlier arrastre, in which heavy stones were dragged in a circular path over the ore by animal power, came from the prehistoric method of grinding grain between two rubbing stones, while the jaw crusher was adapted from simple squeezing devices. But the tumbling grinding mill was not just an adaptation; it was an invention, because it required thinking on a somewhat higher order-there was no prototype. Its nearest antecedents were probably the small closed tumbling drums used in England more than a century ago for cleaning and polishing small iron castings. The date of the first tumbling mill actually used to grind rock is unknown, but it was later than the American Civil War (1861¬1865). It was almost certainly a closed or batch mill in which rock was placed and rotated until it reached the desired particle size. It could have been operated either wet or dry. The first published refer¬ence to such a batch mill was one introduced by Alsing in England (1870) for the grinding of calcined flints for pottery work.21 There are several rather indefinite reports of grinding mills in the early 1890s, including an overflow ball mill in the Helena and Livingstone reduction plant in Montana which may have been the first of its kind. 11 Many of the first mills, which were called tube mills, used hard rock both as grinding media and as mill lining. The rock used was preferably stone from the Normandy and Danish beaches, when it could be imported. This remarkable siliceous stone was already widely used for grist mills throughout America, and its resistance to wear was greatly respected. The decade of the 1890s saw the development of tumbling mills with continuous feed and discharge and their extension into different industrial uses. By 1895 some experience had been accumulated. Iron grinding balls were being tested and the proper speed of rotation was being determined. The Clark Patent tube mill was featured in an E. P. Allis bulletin of 1890, which may have been the first published description of a tube mill. More than 1,000 Gates tube mills had been built by Allis-Chalmers before 1913. Many of these were used in gold mining, espe¬cially in South Africa. The 5 x 22-ft size was particularly favored for grinding portland cement; the use of tumbling mills in the manufac¬ture of cement began about 1900. A great deal of attention was paid to the mill lining. Metal was then relatively expensive, and the general approach was to trap some of the rock grinding media into mill lining pockets. This rock would then absorb the wear and protect the metal lining. In the first ten years of the 20th century there were several different types of pocketed liners, with different manufacturers advancing the superior claims of their patented arrangements. The Osborne liner, developed in South Africa, was probably the most successful. 21 Another item which attracted much attention was size classifica¬tion within the mill and in ancillary equipment attached to the mill and rotating with it. The Krupp type, with interior screens protected inside the mill lining, was developed quite early in Germany, possibly before 1890. The Dorr reciprocating rake classifier (1907) had not yet been invented, and many strange and impractical screening and classifying devices were proposed. In these unsatisfactory machines the two separate processes of size reduction and classification were combined into one operation. It was many years before recognition came that a machine is most efficient when it is designed for one specific purpose. There was much industrial wastage before the opera¬tions of grinding and classification were finally separated. After 1900 the grinding of portland cement raw material and of cement clinker required large numbers of tumbling mills. Most of the raw material was then ground dry. This was also the heyday of gold mining. The old stamp mills that were used in great numbers for grinding gold ore did not grind sufficiently fine to liberate all of the gold, and the new tube mills were installed following the stamps. After 1910 larger diameter tum¬bling mills with larger grinding media were developed. These could receive the finely crushed ore directly, and the inefficient stamp batter¬ies were gradually eliminated. The Rand in South Africa was the greatest gold producer, treating immense quantities of rather low-grade but consistently free milling gold ore. The first tumbling mills, or tube mills, went into operation there in 1904. They were so successful that within a few years no new stamp batteries were installed in the district, even though old ones continued to pound away until after 1950.3 The early tube mills on the Rand all employed Normandy or Danish pebbles, which had to be imported at considerable expense. Their reported wear was as low as 4 lb per ton ground. 4 Many of the mills were lined with the same tough Danish stone cemented into place, while others used the pocketed steel Osborne liner. It was in 1907 on the Rand that an important test was made using hard native ore for grinding media in place of the expensive imported pebbles. 3 This ore, called banket, did not wear as well as the renowned Danish pebbles, but the cost per ton of grinding was definitely reduced. Many of the tube mills on the Rand were soon grinding with native ore. This was the beginning of the development now called autogenous grinding, in which the ore grinds itself. This is treated under a separate heading. See Subsection 3C, Chapter 4. Gold mining was important in America also, and its grinding history follows that of the Rand. Danish pebbles were replaced by native ore in Santa Gertrudis, Mexico, in 1913, 4 and in Consolidated Gold Fields, Nevada, in 1914. 5 Other properties followed suit. However, it gradually became apparent that the capacity of a given mill could be almost doubled if rock grinding media were re¬placed by cast iron or steel grinding balls. In order to increase plant grinding capacity many rock media mills were converted to iron grind¬ing media in the second decade of the present century. In some mills the motor size was doubled; other mills were cut in two and another motor was provided for the second half. Grinding mills began to assume a more modern appearance. Crushing rolls were formerly much used following crushing in jaw or gyratory crushers and preceding grinding in ball mills. How¬ever, the roll surfaces wore rapidly, and skilled maintenance was required to obtain even wear. Rod mills could take feed of the same crusher product size and reduce it finer. The first rod mill was con¬structed by Mine and Smelter Supply Co. and was tested in Canada

Jan 1, 1985

By S. W. Miller

MOST of the steel welding done at the present time is in material containing not over 0.3 per cent. carbon, and the tests here described were in similar material. These tests are not as yet completed but it is hoped that more results and more reasons for the conclusions may be presented at the meeting in February. From the time the author found the peculiar structure in electric welds referred to in a previous paper,1 that is, needles or plates in the grains and similar material, in larger spots, at the grain boundaries, he has felt that these plates which may be iron nitride and probably contain some carbon, were at least partly responsible for the brittleness of electric welds. He has found but few traces of similar lines in oxyacetylene welds until the last 2 mo., when he has found them in large numbers under certain conditions. In the top of these welds, they are quite numerous. In the body of heavy oxyacetylene welds, they appear at times, but not nearly to the extent that they do in electric welds; the author has never seen them in the body of welds in material less than ;3/4 in. (19 mm.) thick. They are shown in Fig. 82. The reason they were not noticed before is undoubtedly due to the fact that in making tests of welded pieces the weld was always ground off level with the plate, and as this structure only appears in the top ;1/16 in. (1.5 mm.) of the weld, they were removed by the grinding or machining; also, welds ¾ in. thick had not been examined. It did not appear, in making bending tests, that this structure had much influence on the strength of oxyacetylene welds; while electric welds are noticeably brittle. Further, oxyacetylene welds made with certain special materials were exceedingly brittle even after the tops of the welds were removed; this was true in cases where there was no sign of the plates whatever and where the welds were remarkably free from oxide and the other usual defects. It appeared, therefore, that this brittleness did not depend on any variable that had been noticed so far, and it was

Jan 2, 1919

By S. W. Miller

MOST of the steel welding done at the present time is in material containing not over 0.3 per cent. carbon, and the tests here described were in similar material. These tests are not as yet completed but it is hoped that more results and more reasons for the conclusions may be presented at the meeting in February. From the time the author found the peculiar structure in electric welds referred to in a previous paper,1 that is, needles or plates in the grains and similar material, in larger spots, at the grain boundaries, he has felt that these plates which may be iron nitride and probably contain some carbon, were at least partly responsible for the brittleness of electric welds. He has found but few traces of similar lines in oxyacetylene welds until the last 2 mo., when he has found them in large numbers under certain conditions. In the top of these welds, they are quite numerous. In the body of heavy oxyacetylene welds, they appear at times, but not nearly to the extent that they do in electric welds; the author has never seen them in the body of welds in material less than ;3/4 in. (19 mm.) thick. They are shown in Fig. 82. The reason they were not noticed before is undoubtedly due to the fact that in making tests of welded pieces the weld was always ground off level with the plate, and as this structure only appears in the top ;1/16 in. (1.5 mm.) of the weld, they were removed by the grinding or machining; also, welds ¾ in. thick had not been examined. It did not appear, in making bending tests, that this structure had much influence on the strength of oxyacetylene welds; while electric welds are noticeably brittle. Further, oxyacetylene welds made with certain special materials were exceedingly brittle even after the tops of the welds were removed; this was true in cases where there was no sign -of the plates whatever and where the welds were remarkably free from oxide and the other usual defects. It appeared, therefore, that this brittleness did not depend on any variable that had been noticed so far, and it was

Jan 2, 1919

By G. G. Brown

Enthalpy-entropy diagrams are presented for natural gases of 0.6, 0.7, 0.8, 0.9, and 1.0 gravity over the pressure range of 5 to 10,000 Ib. per sq. in. and temperature range of 32º to 700°F. The charts indicate directly the work requirement and temperature rise for adiabatic compression or temperature change for free emansion of natural eases. Computation and Uses of Charts The Mollier diagram (Fig. 4), in which the enthalpy (heat content) is plotted against the entropy with lines of constant temperature, pressure,, and in some cases volume, has been found most convenient when dealing with the compression, expansion, and flow of fluids. In dealing with the flow of fluids, the sum of the increase in the enthalpy, AH, plus the increase in kinetic energy, AM —, plus the increase in potential energy, ?MZ, representing the total increase in energy of the fluid in flow, is equal to the sum of the heat q, and work added, —w, to the fluid while flowing between the entrance and exit of the flow system. AH + AM— + ?MZ = q-w [1] In cases where there is no significant change in potential energy or in kinetic energy (velocity), it follows that the increase in enthalpy is equal to the total energy supplied to the fluid. Under such conditions' the changes in the property of the fluid as it flows through a throttling valve, choke, or any other similar arrangement, may be read directly from the enthalpy-entropy diagram by following a horizolltal line between the known pressures' When compressing Or expanding a gas by means of a Or or engine in which no heat is added to or subtracted from the gas, but only work done, the changes in the properties of the gas may be determined along a vertical line of constant entropy between the entering and exit pressures. The power required for the compression of the gas may be readily determined by converting the increase in enthalpy into the desired units. The enthalpy-entropy diagram for natural gases is to the gas engineer what the steam diagram is to the steam-power engineer. For this reason it would be extremely convenient if a reasonably satisfactory enthalpy-entropy diagram could be prepared as a function of the gravity of the gas. A careful study of the known properties of natural gas indicate that this is possible. The effect of temperature upon the enthalpy at constant pressure is expressed as the "heat capacity" or "specific heat" of the gas. The best available data for natural and petroleum refinery gases indicates the relationship shown in Fig. I. From this it is clear that the specific heat of natural gases is a function only of the gas gravity and the temperature at atmospheric pressure. The effect of pressure on the enthalpy of natural gases is dependent upon the pressure-volume-temperature relationships,

Jan 1, 1945

By Leonard A. Duval

This concept employs a viable energy saving method that uses a solvent to separate oil from particle matter; it can be used in metal forming industries to deoil sludges, oxides, and particle matter that is presently committed to landfill. If oily particles are used in their oily state, severe consequences to environmental control systems such as explosions or filter blinding, occur in the air handling equipment. This is due to the presence of hydrocarbons in the stack gases resulting from the oily particles. After deoiling, the particles can be recycled and the separated oil can be used as a fuel. The process does not produce a waste of it's own and does not harm air or water. It demonstrates the dual benefits of being commercially viable and in the national interest of conserving resources.

Jan 1, 1994

By G. Stuart Littlejohn

In spite of recent concerns in certain European countries, I believe that silicate-ester grouts will continue to be employed in practice, unless more cost-effective inorganic grouts are developed for the treatment of fine sands. It is also noteworthy that over the past 40 years, there has been a record of good experience where silicate-ester grouts have been used in ground improvement. Nevertheless, there is now a need via the European Standard EN 12715 (2000) "to assess the environmental impact, particularly the toxicity of the grout and grout components, and their effect on ground and drinking water should be considered before grouting." "When testing the grouting material for environmental impact, the following aspects should be considered: ? Whether during processing, transport or grouting, substance can be generated or released which could be hazardous to the environment or the grouting crew; ? Whether noxious substances can spread upon mixing with ground water; ? Whether reaction products can be produced or released which influence the water quality; ? The type of particles eroded from hardened grout; ? Chemical reactions between hardened grout and the ground water."

Feb 10, 2003