Search Documents

By K. E. J. Rapperport, C. S. Hartley

The only slip system observed in zirconium crystals deformed at 77", 575", and 1075OK was (1010) [1210] with a critical resolved shear stress in tension of 1.0 kg per sq mm at 77°K; 0.2 kg per sq mm at 575 °K; and 0.02 kg per sq mm at 1075 OK. The active twin planes were {1012}, (1121}, (11221, and (11233) with varying temperature dependence. A detailed analysis for the slip direction using Laue spot asterism is appended. NeARLY all metals of the hexagonal close-packed structure exhibit basal slip, i. e.,(0002)<1120>- type slip. This is true of magnesium,&apos; zinc,&apos; cadmium,3 beryllium,4 titanium,= yttrium,6 and rhenium.Many of these such as titanium 5&apos;8-&apos;0beryllium,4&apos;" magnesium, and zinc13&apos;14 display other slip modes even at room temperature, and nearly all have been reported to slip on other systems under particular loading or temperature conditions of testing. As is shown in this paper, basal slip was not found at any of four test temperatures from 77" to 1075°K in hexagonal close-packed zirconium under the simple loading conditions of tension and compression, even though in one case the resolved shear stress on the inactive (0002) <llgO> system was twenty-five times higher than the critical resolved shear stress on the active (1010) [1210] system. This result is consistent with prior studies on the active deformation processes in zirconium deformed at room temperature. &apos;&apos;-I7 SPECIMEN PREPARATION A) Material—The zirconium used in this work was of two types: 1) as-deposited reactor grade crystal-bar, and 2) arc-melted and forged reactor grade crystal-bar. Typical chemical and spectrographic analyses of these materials as received, and after hydrogen removal and crystal growth are given in Ref. 17. Crystals of type 1) above have the letter prefix (A) and those of type 2) have the prefix (B) throughout this paper. B) Crystal Growth— he zirconium was machined into rectangular parallelepipeds about 0.2-in. scl in cross section and 2 in. iong. These were hand polished through 4/0 abrasive paper, electropolished, given a hydrogen removal anneal, and subjected to long-time anneals at 840 °C in vacuo to produce usable crystals.&apos;7 A second technique used to obtain large crystals was to cycle the samples two or three times between 1200" and 840°C, allowing them to remain at the higher temperature for about 4 hr and at the lower temperature for 5 days.17 These techniques yielded some grains which occupied the entire cross section of the bar and were as long as 3/4 in. C) Orientation Determination—After the growth of large crystals by thermal cycling, the samples were repolished with extreme care through 4/0 abrasive paper and electropolished. Metallographic examination after polishing showed the surfaces to be free of visible deformation traces. Standard Laue back-reflection X-ray techniques were used to find the crystallographic orientations of selected large grains with respect to a specimen face and edge. Fig. 1 shows the stereographic projections of the stress axes for the crystals used. The sharpness of the spots on the Laue photographs indicated that the crystals were of good quality. EXPERIMENTAL METHODS Nine crystals were deformed in tension at 77"K, nine in tension and five in compression at 300°K in previous tests,17 fifteen in tension at 575"K, and eleven in tension at 1075°K. All specimens were stressed by load increments. After a predetermined load was applied, the specimen was removed from the loading appratus and metallographically examined for deformation traces. An attempt was made to initially stress each bar so that some crystals slipped a small amount and others not at all. This was done to bracket the critical resolved shear stress. One bar of special orientation (B-11) was repolished and annealed at 1075°K for 1 hr after lower temperature deformation, before final deformation at 1075°K. In the other bars the loading by increments, followed by metallographic examination, was continued until the surface distortion would interfere with analysis, or until fracture. One example of a crystal pulled to fracture is shown in Fig. 2. This photograph shows a crystal (B-14C) which was pulled at 1075°K and failed by slip on two (10i0) planes. The approximate orientation of this crystal is illustrated in the figure. Specimens were deformed at 77°K in liquid nitrogen on a tensile machine using an insulated bucket with an internal hook to accept a clamped specimen.

Jan 1, 1961

By G. K. Manning, A. R. Elsea, C. R. Simcoe

Boron increases the hardenability of hypoeutectoid steels by decreasing the nucleation rate of ferrite and bainite. It is postulated that concentrations of lattice imperfections, such as exist at the grain boundaries, furnish the necessary energy for nucleus formation. Boron, because of its atomic diameter, will concentrate at lattice imperfections where sites of suitable size are present. Boron will decrease the energy of these local areas by occupying these sites. This mechanism accounts for the large increase in hardenability observed with small amounts of boron. The loss of the boron hardenability effect and the boron precipitate formation are explained on the basis of increased concentration of boron at the grain boundaries either with increasing boron content of the material or with increasing temperature. COMMON alloying elements affect both the nucleation and growth rates of the austenite decomposition reactions.&apos; This effect is largely a result of the slow diffusion rates of these elements. Although a small addition of boron markedly increases the hardenability of steel, the diffusion rate of boron, which is of the same order of magnitude as that of carbon, can hardly account for this effect. An addition of boron in the range of 0.001 to 0.003 pct is about as effective as an addition of 0.30 pct Mo, 0.40 pct Cr, or 1.25 pct Ni in increasing the hardenability of a 0.40 pct C steel;&apos; however, increasing the carbon content of the steel decreases the effectiveness of the boron addition."&apos; The difficulty in understanding why so small an addition of boron can replace much larger quantities of the more strategic alloys, together with the erratic behavior sometimes encountered in boron-treated steels, has interfered with their general acceptance by industry. In the belief that an understanding of the mechanism by which boron increases the hardenability of steel should lead to a more general acceptance of boron-treated steels, a research investigation to determine this mechanism was undertaken at Battelle Memorial Institute under sponsorship of Wright Air Development Center. Experimental Work In order to study the effect of boron on the transformation of austenite to ferrite and bainite, a group of steels was made with a basic composition similar to that of the SAE 8600 series. This base composition was chosen because it has sufficient hardenability to permit accurate measurement of the times required for transformation to start at various temperatures. The chemical analyses of the steels used in the first part of this investigation are listed in Table I. These steels were made as 200 lb heats in an induction furnace. The furnace charge was Armco ingot iron with the alloying elements added as ferroalloys. After the alloy additions were made, the heat was deoxidized with 0.125 pct Al. A 100 lb ingot was cast and an addition of 0.003 pct B, as ferroboron, was made to the metal remaining in the furnace. This metal was cast into a second 100 lb ingot. The ingots were forged to 11/4 in. diam bar stock from which end-quench hardenability specimens were obtained. Part of this material was further reduced by hot rolling to lx¼ in. bar stock from which specimens were obtained for isothermal transformation studies. Studies of Nucleation and Growth: End-quench hardenability tests were performed on these steels, using an austenitizing temperature of 1600°F. The hardenability curves, shown in Fig. 1, indicate that boron treatment resulted in considerable increase in hardenability of the steels. Any such change in hardenability must result from a change in the transformation rate of the austenite, and these rate changes can be established readily by isothermal transformation studies. Isothermal transformation studies were conducted on these steels as follows: specimens were austeni-tized at 1600°F for 15 min, transferred to a lead bath operating at a constant subcritical or intercritical temperature, held for various lengths of time, and water quenched. The specimens were sectioned for metallographic examination to determine the amount and the type of transformation products present. In order to determine the effect of boron on the formation rate of ferrite, isothermal transformation tests were made on the 0.20 pct C steel in both the boron-treated and boron-free condition at an intercritical temperature of 1375°F where ferrite is the only decomposition product of this low carbon austenite. The results of these tests are shown in Fig. 2, where the percentage of ferrite formed is plotted as a function of time at temperature. It is apparent that boron markedly decreased the transformation rate of austenite to ferrite at this temperature.

Jan 1, 1956

By G. L. F. Powell

g samples of Cu-20 wt pct Ag alloy have been mdercooled to a maximum of 197°C by melting under a slag of commercial soda-lime glass in a vitreous silica crucible. No grain refinement of the primary copper was observed in samples undercooled to the maximum of 197°C. When the samples contained a small amount of oxygen, the copper dendrites were partially recrystallized at undercoolings greater than 97°C. In previous papers&apos;-3 reporting the grain structure of undercooled silver and copper, it was observed that grain refinement was dependent on both undercooling and oxygen content. Grain refinement occurred in undercooled silver when the degree of undercooling exceeded the range 153" to 175"C, while in Ag-0 alloys (0.12 wt pct) fine equiaxed grains were exhibited when undercooling was greater than 50°C. Similarly, copper samples undercooled as much as 208°C displayed fan-shaped growth from a single nucleation site, while the grain structure of Cu-O alloys (0.08 wt pct) was fine and equiaxed at undercoolings larger than 150°C. Thus the presence of oxygen greatly reduced the undercooling at which grain refinement occurred. It was also observed that the change in grain size resulted from recrystallization and was not due to an enhanced nucleation rate in the liquid-solid transformation. It is possible that the influence of oxygen on recrystallization is due primarily to its presence as a solute element. walker4,&apos; reported that, although a grain size change did not occur in pure nickel until the undercooling exceeded 150°C, small grains were observed in samples of Ni-Cu alloy solidified at small and large degrees of undercooling. Jackson et al.6 suggested that the fine grained structure of the Ni-Cu alloy resulted from the melting off of dendrite arms during recalescence. This remelting process may occur in alloys as a result of segregation during freezing which causes a variation in liquidus temperature from point to point within a dendrite. It was therefore decided to undercool copper with a metallic alloying element to ascertain whether the presence of a metallic solute would have a similar effect to oxygen in inducing grain refinement. A Cu-Ag alloy was chosen, since both metals had been shown to behave similarly on undercooling. The alloy Cu-20 wt pct Ag was selected since the eutectic constituent outlines the initial growth form of the primary copper, so that the as-frozen grain structure is not obscured if subsequent recrystallization occurs. This paper describes the results of undercooling experiments carried out with Cu-20 pct Ag samples undercooled to a maximum of 197°C and the effect of oxygen content on the grain structure of the undercooled samples. EXPERIMENTAL Melting was carried out in a small cylindrical resistance furnace using "fine" silver granulate and oxygen-free high conductivity copper. The procedure adopted was to melt the required quantity of silver in air in a clean vitreous silica crucible for approximately 15 min, freeze, and add granulated commercial soda-lime glass to form a complete surface slag cover, after which the sample was melted and frozen several times to reduce the oxygen content. The glass slag cover was approximately 3 in. thick. Pieces of copper (=50 g) were added to the crucible until the required quantity to make 350-g samples of alloy had been charged. Each piece was added quickly to the crucible which was held at a temperature slightly above the melting point of silver. The piece was quickly pushed beneath the glass to minimize oxidation and any oxide coating usually decomposed before the piece had settled down into the silver. After the full quantity of copper had been added, the melt was stirred with a silica rod to hasten homogenization and a Pt/Pt 13 pct Rh thermocouple enclosed in a vitreous silica sheath inserted for temperature measurement. Heating and cooling curves were recorded on a potentiometric chart recorder fitted with a zero suppression unit. The milli-voltage range of the recorder was adjusted so that temperatures could be read to 1°C. Heating and cooling curves were taken every hour until three consecutive readings gave the same solidus-liquidus range, consistent with the solidus-liquidus range for this alloy composition by reference to Hansen and Anderko.7 Metallographic examination of samples frozen at this stage, failed to show any variation in composition from bottom to top of the ingot. Consequently, it was considered that the melt was homogeneous at this stage and undercooling experiments were then car-

Jan 1, 1970

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

The tensile properties, creep resistance. and thermal stability of highly alloyed Ti-Al-Zr alloys were examined. On the basis of these studies, the Ti-7Al-1ZZr composition was selected for more complete evaluation. The alloy was found to be weldable and free from excessive directionality. In addition, it developed maximum properties without requiring heat treatment other than an annealing operation in the alpha field. The alloy was recommended for scale up and is presently being investigated on a production-level basis. One of the more attractive properties of titanium alloys is their ability to withstand stress at moderately high temperatures, and a considerable amount of effort has been devoted to increasing the maximum service temperature of titanium alloys. This work has suggested that the optimum alloys for high-temperature service will be single-phase a (close-packed hexagonal) alloys containing significant amounts of aluminum. However, the maximum amount of aluminum which can be alloyed with titanium is between 6 and 8 pct,l since at high-aluminum contents an embrittlement reaction occurs in the anticipated service temperature range, 800" to 1100°F. It has been shown that the embrittlement reaction involves decomposition of the high-aluminum a phase to one or more new phases.&apos; Since this reaction does not occur at intermediate or low-aluminum contents, it was felt that intermediate Ti-A1 alloys might be strengthened by a-soluble ternary additions without inducing the embrittlement reaction. The first alloying addition considered was tin, which shows extensive solubility in a titanium and has moderate strengthening tendencies. Unfortunately, it was soon apparent that tin also promoted the embrittlement reaction, and that to obtain a stable alloy, the aluminum content had to be reduced as the tin content was increased. The second alloying addition considered was zirconium, which is similar to tin in its effects on titanium. This element did not contribute to the embrittlement reaction and, in fact, appeared to increase the maximum amount of aluminum which could be alloyed with titanium without inducing instability. This paper describes an investigation of the Ti-A1-Zr a alloy region. Alloys containing from 4 to 12 pct A1 and from 6 to 15 pct Zr were examined. The properties of these alloys are described and the bases for selecting an optimum composition is outlined. This composition, Ti-7A1-12Zr, is presently being scaled up in tonnage quantities, and is being evaluated extensively throughout the industry. In addition to presenting the basis for its selection, this paper presents a description of the properties developed in laboratory material as determined during the alloy investigation. These properties suggest that this alloy can fill an important position in applications requiring light weight, fabrica-bility, weldability, and strength to 1000oF or higher. EXPERIMENTAL PROCEDURES Titanium alloy ingots were prepared by inert electrode arc melting under an argon atmosphere. Alloying elements used were 110 Bhn titanium sponge, high-purity aluminum, and reactor-grade zirconium. Pancake-shaped ingots were prepared weighing approximately 300 g. The composition of the ingots was checked by weight measurements before and after melting. The pancake ingots were forged at 2000°F to approximately half their original thickness to give a flat plate roughly 1/2 in. thick. This plate was then rolled at 1800&apos; to 1600°F to 0.250 in. thick. All of the alloys examined fabricated well. However, alloys containing 15 pct Zr tended to overheat due to exothermic oxidation, and scaling was excessive. As might be anticipated from its effect in decreasing the ß transus, increased zirconium appeared to improve fabricability somewhat, especially during rolling at lower temperatures. Except for a limited study of heat-treatment response, all alloys were examined in the a-annealed condition. Prior to heat treatment the a and ß tran-sus temperatures were determined by metallo-graphic examination of samples quenched after annealing at 50-deg intervals in the transformation region. These data are shown in Fig. 1. Recrystal-lization appeared to occur in about 1 hr in the range 1300º to 1500ºF. Therefore, alloys were annealed for 1 hr at 1550ºF (4 and 5 pct Al), 1600ºF (6 through 7-1/2 pct Al), or 1650°F (8 or more pct Al). This produced an equiaxed a grain structure. In most alloys, a "ghost" structure was visible after the a-annealing treatment, as shown in Fig. 2. This structure apparently resulted from the acicular

Jan 1, 1963

By R. M. Giegerich

"This paper begins with a brief history of Madawaska Mines, a brief description of the geology, mining methods and equipment, and the historical development of 7/8-in. tapered drilling equipment. It then outlines the performance characteristics and inherent problems of the traditional 12-degree, tapered connection, blade-type insert bits. Service-free (Unipass) button-type insert bits are presented as a possible solution to these problems. The paper concludes with an analysis of button bit performance to date.Brief History of Madawaska MinesMadawaska Mines Limited, near Bancroft, Ontario, is in Faraday Township, Hastings County, approximately 100 miles northeast of Toronto and 100 miles west of Ottawa.The mine re-opened in 1976committed to 1,500 tons per day to provide approximately 600,000 pounds of yellowcake (U3O8) per year to A.G.I.P. (an Italian government agency) under the joint ownership of Federal Resources Corporation, Salt Lake City (51%), and Consolidated Canadian Faraday Limited (49%). At present, the mine is producing approximately 2 pounds per ton (.1% U3O8) at the rate of 60,000 pounds per month. The mine employs about 400 employees.Brief Description of Geology, Mining Methods and EquipmentGeologyThe Grenville metasediments of the mine area are chiefly paragneiss, amphobolite and some carbonate (marble) rocks, which were intruded by a basic rock, altered to a metagabbrometadiorite. These formations are generally concordant, striking east to northeast and dipping 45 to 60 degrees to the south. Locally, the metagabbro is often discordant. The above group of rocks (mixed hybrid gneisses) forms the hanging wall of the south-dipping Faraday granite sheet and was intruded by nepheline syenite, syenite and granite. The ore occurs in the granite-syenite-pegmatite dykes that are probably genetically related to the Faraday granite. The ore shoots are erratically distributed within the pegmatite bodies, mainly on the hanging or footwalls but also medially. Their size varies from 50 to 350 feet in length, 5 to 40 feet in width and 50 to 200 feet in height. The ore occurs most frequently in a medium-grained granite or syenite, well hematized with 10 to 30% mafic crystals of pyroxene, amphibole and/or relics of the host rock."

Jan 1, 1982

By A. B. Parsons

NOT every organization on reaching the relatively ripe age of three score and fifteen can say with truth that its purpose and objects remain precisely the same as prescribed by its founding fathers. Of course, constancy of purpose may be something else than unalloyed virtue. It could merely reflect slavish worship of tradition, intellectual stagnation, or sheer inertia. On the other hand, it could establish the fact that the founders were men possessed of broad outlook, of prophetic vision, and of an acute sense of direction. In addition to charting the course with precision, the founders of the A.I.M.E. surely showed a flair for expressing clearly in a few words what others might say obscurely in many words. To quote verbatim from the "call" for the meeting, in 1871, the proposed organization was to have: "two great objectives: "First, the more economical production of the useful minerals and metals. "Second, the greater safety and welfare of those employed in these industries." This text underwent some refining on several subsequent occasions but today the ultimate product, as set forth in the Constitution reads: "to promote the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by all lawful means." The original call was dated "Wilkes-Barre, Pa., April, 1871," and was signed by Eckley B. Coxe, of Jeddo, and by R. P. Rothwell and Martin Coryell, both of Wilkes-Barre, each of the three subscribing himself as "mining engineer." The authors proceeded to explain briefly just how it was proposed to achieve these objectives: "In European countries, where the arts of mining and metallurgy have long been the subject of the most careful study, no means have been found so effectual in attaining the end above proposed, as the free interchange of experience among those actually engaged in these industries; and this object has been accomplished mainly through the medium of `Institutes,&apos; `Associations,&apos; or `Societies,&apos; composed of those engaged in these occupations, and by the periodical publication of `essays&apos; or `papers&apos; communicated to such societies by their members. "It must be evident to all practical men that the interchange of the varied experience

Jan 1, 1947

By P. G. Keohane, J. S. Drake

"Cominco&apos;s Polaris Mine is a lead-zinc underground operation that began commercial production in early 1982. The mine site is located on Little Cornwallis Island in the Canadian Arctic at a latitude of 75°23&apos;N and at a longitude of 96°55&apos;W. The nearest settlement, Resolute Bay, some 100 kilometres southeasterly from the mine, is accessed from the mine by light aircraft. The mine site can be accessed by sea during the six-week ice-free period each year. During this time all major operating supplies are brought to the mine and the lead and zinc concentrate products are shipped out to market.GeologyThe Polaris orebody lies near the top of the Thumb Mountain Formation of Ordovician age. This formation is a relatively homogeneous section of thin to medium bedded limestones which are brecciated and dolomitized in the area around the orebody. The deposit is described as a Mississippi Valley-type orebody. Ore minerals are sphalerite and galena with the waste being predominantly dolomite with calcite and marcasite. The ore is quite porous with voids being generally filled with ice as the mineralized zone lies entirely within permafrost. Reserves consist of about twenty million tonnes of ore grading 3.8% Pb and 14.3% Zn with a further three million tonnes of inferred ore at a slightly lower grade.The orebody strikes in a north-south direction with the hangingwall dipping at about twenty degrees to the east. It is generally conformable with the stratigraphy. The footwall in the western portion of the orebody, the Panhandle, lies about 10 to 30 metres below the hangingwall. To the east the footwall drops sharply, creating an orebody height of up to 110 metres in what is referred to as the Keel Zone. The Panhandle Zone has typically 80 - 110 metres of cover above the hangingwall , About 25% of the reserves are in the Panhandle Zone, the remainder being in the Keel Zone. Figure I illustrates a plan view of the orebody relative to other surface facilities on the property and Figure 2 illustrates a simplified section through the Panhandle and Keel Zones."

Jan 1, 1985

By J. W. Smith, J. Van Dusen, A. Papachristodoulou

"As part of a study to evaluate factors affecting tankroom air quality, the mechanism of aerosol generation from bursting bubbles in electrowinning operations has been investigated. Typically 2 to 3 mg/m2.s are produced in zinc tankrooms. Analysis shows that the rate of production of film drops (geometric mean diameter - 2 urn] increases with decreasing bubble size, and that jet droplets (geometric mean diameter - 20 um) are not produced with gas bubble larger than - 4 mm. Both mechanisms of drop formation and current efficiency are affected by surface active agents, with an over-all reduction in emission of up to 60% to 70% being achievable. A source control system which does not adversely affect electrolyte properties is always preferred, and coalescence of all gas bubbles in to a continuous stream of gas at a single point on the electrolyte surface would eliminate aerosol emissions. This objective was the basis for design of a coalescence device which, in laboratory tests, reduced the emission rate by over 95%.The control device fit s over the electrodes in the electrowinning cell and is partially immersed in the electrolyte. A number of changes in the design which resulted in significant improvement in the performance of the device are reported.Field tests have shown that only about 75% of the aerosol below 10 um can be eliminated by coalescence. The remainder (up to 95% of the total) is controlled by coalescence of droplets, by impaction on the exposed collector surface and gravitational settling.The device does not interfere with operation of the tankroom, handles the effect of surges in power during harvesting, and is simple and inexpensive to maintain. IntroductionDuring the electrowinning of metals (such as zinc and copper) gases are evolved along the electrode surface forming small bubbles. The bubbles travel upwards and burst on the electrolyte free surface generating, in this way, small droplets. Because the electrolyte is often highly acidic or contains toxic materials, the whole process can result in the formation of an aerosol in the atmosphere above the electrowinning cells which poses a serious health hazard to workers in the area, and corrodes equipment."

Jan 1, 1988

By M. B. Mirza, F. D. Wright

Models of photoelastic material were made to simulate a mine roof that had cracked over the edge of the pillars and at the center of the span. Models were restrained from moving laterally outward so they acted as flat arches. Uniform loading was approximated by loading the models along the bottom at eight points spaced equally along the span. It was found that for models with depth to span ratios of 1:3 to 1:6, the maximum stress at the top of the center crack could be calculated directly by the following formula: Elastic stresses in mine roofs composed of sedimentary beds are usually computed by assuming that the immediate roof bed acts as a fully restrained beam uniformly loaded by its own weight and by overlying strata. Very little work has been done to analyze stresses in roof beds or beams which contain vertical (normal to the span) or nearly vertical cracks. Yet every mining engineer has walked safely under roofs that show such cracks. As far back as 1933, Bucky&apos; made model studies of the effect of vertical cracks on the behavior of horizontal strata. He did not make any analysis of the stresses but did show that a cracked beam will stand safely under certain conditions, and also showed that a beam restrained at the ends can crack over the supports and in the middle without collapsing as long as the ends of the beam are not free to move laterally outward. The beam, or rather, part of the beam, acts like a flat arch and supports itself by pushing outward at its supports. In 1941 Evans2 treated analytically the problem of a beam cracked along so many planes perpendicular to the axis of the beam that no tensile stress can operate. He named this type of beam a "voussoir-beam" by analogy to the voussoir-arch. In 1962 ~a~cocks~ modified Evans&apos;s solution by including the effect of the shear stress component of the resultant force at the abutment. This paper gives the results of a photoelastic study of the stresses in a beam containing vertical cracks in the center of the span and over the supports. A

Jan 1, 1963

"A 3-dimensional finite element model for stress/stability analysis of rock excavations in underground mines is presented. Developed for use on personal computer under OS/2 operating system, the model employs the 8-node isoparametric brick element and accounts for such loading conditions as in situ stresses and gravity loading of the rock mass. In addition, modelling of backfill in mine stopes as in situ stress-free material is incorporated. Material failure is assessed by Mohr-Coulomb or Hoek-Brown failure criterion. A mine design example is presented to illustrate the potential use of the model as a tool for stope design.IntroductionNumerical modelling of mine structures has become a vital tool for mine design in recent years. The need to maximize ore extraction ratio and to reach deeper mineral deposits underground has led the mining industry to employ numerical methods of analysis to undertake complex ground control studies in order to better understand the ground response to mining excavations and to evaluate the ground support requirements. Thanks to the rapid developments in computer technology, it is now possible to perform very comprehensive analyses including, but not limited to, 3-dimensional, elasto-plastic, or large deformation or time dependent nonlinear analyses on personal computer.During the past ten years or so, many researchers undertook 3-D finite element analyses of rock mechanics problems in mining engineering. The following is only a sample review. For example, Chan&apos;!&apos; used three-dimensional finite elements to study the mechanical response of jointed granite during shaft sinking at the Canadian Underground Research Laboratory. Wang et al.(2) performed 2-D and 3-D finite element analyses of room-and-pillar mining system with flat and rolling coal seams. Thatejatu used three-dimensional finite element method to examine the problem of branching tunnels. Dolezalovaw used three-dimensional finite elements for the analysis of tunnel-face advance with partial excavation as well as full-face excavation in combination with rein for cement of the face by long anchors. Peili (5) used three-dimensional finite elements for the simulation of rock-liner interaction near the tunnel face."

Jan 1, 1992

By D. A. Whitley, R. P. Carone

"Shaft sinking by blind shaft drilling offers the mining industry a different approach to shaft construction. Benefits of blind drilling include less construction time and fewer safety problems while being economically competitive with conventional sinking methods under certain conditions in soft water-bearing formations.Technology and equipment are available today to drill blind shafts up to 20 feet in diameter and over 3,000 feet deep. This is an extension of proven techniques developed by private industry. To drill a 20-foot-diameter hole requires a specially manufactured hydraulic drill unit with a rated hoist of 2 million pounds and 500,000 ft/lb of torque.This brief paper will discuss the following aspects of blind shaft drilling:• benefits;• equipment f or drilling;• circulation methods;• circulation rates;• shaft alignment; and• progress rates to be expected.IntroductionShaft sinking by blind shaft drilling offers the mining industry an improved alternative method for shaft construction. The drilling of 20-foot -diameter shafts to depth s in excess of 3,000 feet can be done by utilizing equipment specifically designed and manufactured for this purpose. This equipment is a distant cousin, at best, to standard oil well drilling rigs. The actual configuration of these drilling machines will be discussed in a following section.To most people, the drilling of mine shafts may seem to be a new or at least recent technology. However, as early as the I920s, German and Dutch miners were drilling 24-foot diameter shafts for coal mines. What led ""miners to resort to drilling were ground conditions that still plague conventional shaft sinkers today: soft , water-bearing formations. The major drawback to these early attempts was a low penetration rate due to poor bit cleaning. This, however, was not the end of early shaft drilling activity. From 1936 to 1950, a number of mine shafts were drilled by the calyx or coring method. This method employs a bit with a large bore down the center. As it drills, it cuts a core. When 5 to 10 feet have been drilled, the core is removed. The disadvantages of this method were the time and work involved in breaking the core free, and it was inadequate in soft water-bearing ground."

Jan 1, 1981

By Wilson T. Lundy

The history of the production of sulfur from salt domes in Louisiana and Texas originated with the operations of the Union Sulphur CO. at Sulphur, La., followed by the Freeport Sulphur Co. at Bryanmound, Tex. Including the present development of Grande Ecaille by the Free-port Sulphur Co., which constitutes the tenth dome to be equipped for the production of sulfur in the Gulf Coast, less than 10 per cent of all the known domes have proved to contain sulfur in commercial quantities. The Grande Ecaille salt dome is in the tidal marsh of the Mississippi River delta in Plaquemines Parish, Louisiana. It is 10 miles southwest of the right descending bank of the river approximately 45 miles below the city of New Orleans and is within 4 miles of the shore line of the Gulf of Mexico. Terrain Characteristic of the delta region, the terrain consists of a low, flat, uninhabited area of marsh land intersected by many shallow lakes and bayous. With the exception of salt grasses, the region is devoid of vegetation and presents, in all directions, an unobstructed path to the vagaries of the winds. The general character of this area can be best visualized from the mechanism of its formation.&apos; Offshore bars formed enclosing long narrow lagoons between the bar and the inner shore line, the lagoons communicating with the sea by means of tidal inlets. The water in the lagoons, being comparatively quiet, favored the deposition of fine debris composed of sand carried into the lagoons by action of the waves, tides and river-borne sediments from the land surface. As this material accumulated the bottoms of the lagoons were built up and eventually salt grasses obtained a foothold. The successions of growth and decay of these grasses formed a brown fibrous mat varying in depth from a few inches to several feet. This mat of vegetation virtually floats on an ooze that is several feet thick and is composed of alluvial sediments and very fine sand, and the whole is underlain by an unctuous clay. The decayed vegetation from the upper layer when dried has a peaty appearance.

Jan 1, 1934

By James K. Stanley

When a plastically deformed mctal is heated to a certain temperature, it undergoes a complete change in microstructure, the consequence of which is a marked alteration of mechanical properties such as hardness, strength and ductility. This change in microstructure occurs by re-crystallization and is a process involving the formation and growth of strain-free nuclei in the deformed matrix. These nuclei continue to form with time and grow until a new grain structure replaces the cold-worked structure. The formation of the nuclei in the deformed sheet of I per cent silicon ferrite is illustrated in Fig. I. If a recrystallization is conducted iso-thermally, a nleasurement of the fraction of the matrix recrystallized plotted against time leads to an isothermal recrystallization curve, first established in 1942.1 Such recrystallization curves are shown in Fig. 4. These curves show that the recrystallization of a cold-worked metal is best considered as a rate process rather than a time independent process such as is suggcsted by the improperly named and misleading recrystallization diagrams involving deformation, temperature, and grain size.2-5 Any study of the rate of recrystallization resolves itself into a study of the component rates of nucleation and growth. The previous paper1 provided an account of the determination of the rates of nucleation; N, the number of nuclei formed per unit time per unit of unre-crystallized area, and growth, G, the radial growth in unit time, in the recrystallization of silicon ferrite (I per cent Si). A method was developed to furnish experimental data for evaluating the effect of the recrystallization variables on N and G. The mathematical analysis for the derivation of the isothermal recrystallization curve was developed for a two-dimensional case (in thin sheets where the diameter of the recrystallized grain is greater than the sheet thickness). The present paper is a continuation of the study of recrystallization of I per cent silicon ferrite begun in 1942.1 In this work the effect of the factors deformation, temperature, grain size, composition, and recovery is studied with respect to the rates of liucleation and grouth. At the same time it is shown how the cooperation of N and G affects the isothermal recrystallization curve. The study of these variables on N and G has a definite bearing on the mechanism of recrystallization and should lay a foundation for a rational theory on the subject. Procedure The procedure used in these experiments was essentially the same as that described previously but in certain details some changes were made in the interests of speed. With few exceptions, the procedure is the same for the study of all the variables. Where the procedure is different from standard manipulations attention is called to this fact.

Jan 1, 1945

Statistical summary of the mineral industry world production, exports and imports 1964-1969 Published by Her Majesty&apos;s Stationery Office, London, on behalf of the Institute of Geological Sciences (1971) The Statistical Summary contains a wealth of care fully garnered information on the production, exports and imports of the principal minerals and mineral products throughout the world for the period 1964-1969, and it should therefore be of particular interest to economic geologists and others concerned with marketing and selling minerals. In view of the intractable nature of the source data it is quite an achievement to have published figures for 1969 so expeditiously. On picking up the Summary this reviewer instinctively compared it with the Annual Yearbook published by the United States Department of the Interior. The Yearbooks have been issued annually since 1882, and today each consists of a set of three separate books containing five volumes. Apart from abundant statistics on the domestic and international mineral industries, the Yearbooks are known for their perspicacious reviews and articles on a host of different facets of the world&apos;s minerals industry. Physically the Summary is a much slimmer publication than the Yearbook, and it contains no commentary whatsoever other than occasional footnotes. The principal contents are a series of tables showing production, exports and imports of fifty-nine of the world&apos;s more important minerals and mineral products. Each table shows the weight of the material produced or traded, by countries, with figures for each of the six years in adjoining columns. In some cases (e.g. diamonds) values in British currency are quoted in addition to weights. Most of the data have been abstracted from national reports and returns, although in some instances estimates are quoted where national sources are silent--as for example the production of platinum in South Africa. One wonders in passing if any useful purpose is served by the continued suppression of this particular figure. The four South African producers must surely be able to estimate each other&apos;s production fairly accurately by now, and one imagines that the national export figures can likewise be synthesised. This reviewer has two minor criticisms of an otherwise praiseworthy publication. Firstly it seems an unnecessary anachronism to perpetuate the split between &apos;Commonwealth&apos; and &apos;Other&apos; countries-the split can have little practical significance today. Secondly, what is one to make of the statement that the 1966-1969 figures for exports from Rhodesia of chrome ore and copper, to take two examples only, are &apos;not available&apos;? It seems improbable that no estimates of these figures have been made since the imposition of sanctions, and inevitably one suspects that the figures have been excluded on policy grounds. Hopefully this problem will have been solved when the next Summary is published. M.J.M. South Africa, land of Challenge by Maurice Tyack France Interpresse, 323 pages, price R18-00. Is South Africa God&apos;s richest acre? In its mineral wealth it certainly is, but what of the many other complex overlays of emotions, traditions and racial problems? South Africa, Land of Challenge, provides the background. This is reported to be the first comprehensive documentary work of its kind on South Africa. It is a handsome volume measuring 12ft by 9f&apos;, is illustrated by at least 600 photographs of South Africa, more than half of which are in colour, and contains 21 original maps and charts. The book covers the full spectrum of South Africa&apos;s very existence, its geography, pre-history, its customs, countryside, natural resources and its cities. The more controversial categories are thoroughly discussed, the people, their policies and politics. Mr Tyack is eminently qualified to write on South Africa, being the author of over 20 books on other African countries and having spent more than three years of research, in the field, in South African archives and also in various libraries and museums, in preparation for this book. The book claims to be free of any party political bias and appears to be an honest attempt at a factual survey. However, a work of this magnitude will undoubtedly leave an impression on the reader and the tone of this book is decidedly patriotic. This is a useful reference work on South Africa that most South Africans will be proud to own. J.P.H. Ergonomics and physical environmental factors This publication by I.L.O. of a symposium in Rome in September 1968 has much useful information for the mining industry in regard to the health and productivity of its labour force. The first subject dealt with is mechanical vibrations. From this section it is clear that men who drive, for many hours each day, vehicles which vibrate in the 6 Hz range are subject to serious physiological and psychological effects. The former may show as changes to the vertebral column (which has a resonance in the 4-5 Hz range). The circulatory system is adversely effected by values in the 6-10 Hz range and the vision is impaired at between 40-100 Hz. Less definite knowledge exists of the effects of vibration on the hand-arm system from mechanical drills etc, although Raynauds disease of the blood vessels of the hand and degenerative diseases of the elbow and shoulder joints occur in men using drills which vibrate, respectively, in the higher and low frequency ranges. Industrial noise is extremely well dealt with and the latest knowledge is summarized. Clear information is given on the relationship between time of exposure to

By R. C. Buehl, J. P. Morris

F. D. Richardson—The authors are to be congratulated on this further contribution to our knowledge of the thermodynamics of the interaction between sulphur and carbon and silicon in liquid iron. As the authors state, the influence of carbon and silicon on the activity coefficient of sulphur in liquid iron is clearly of great importance in the blast furnace, since it must cause a three to fourfold improvement in the partition of sulphur between slag and metal. The influence of increasing temperature in further increasing the activity coefficient of the sulphur in the metal in the blast furnace by increasing the carbon content is also of interest. This effect, however, is probably only part of the reason for the general observation in blast furnace practice, that the sulphur content of the metal is lowered by increasing temperature. Other contributing factors are the lowering of the oxygen potential in the presence of carbon by increasing temperature and the probable increase in the activity coefficient of the lime in the slag for the same reason. The former of these effects, which works via the (CaO) + [S] = (CaS) + [O] equilibrium, might possibly account for a 70 pct improvement in the sulphur partition and the latter might give a further 50 pct improvement. C. Sherman—I would like to compliment the authors on their very careful research. If I may, I would like to show results of calculations on the carbon-sulphur-iron system similar to the ones that were shown in our paper for the silicon-sulphur-iron system. For Fe-S-C ternary system k=PHgs/PH2 x 1/(f1°) (f2°) (%S) where fs = sulphur activity coefficient fs&apos; = fs for Fe-S system of equal pct S f3° = f2/f2 for Fe-S-C ternary system This same analysis has been used on other systems, but the results shown in fie.- 7 are for carbon and silicon. L. S. Darken—I would like to make two brief comments in addition to complimenting the authors on an apparently very precise and accurate investigation. The first is that the present work is in agreement with a calculation by Larsen and myself." Our calculation (much less precise than the present work) was based on: (1) Unpublished work on the sulphur content of molten iron (1.5 pct at 1500°C) in equilibrium with graphite and an iron sulphide slag; (2) the distribution coefficient of sulphur between slag and carbon-free liquid iron. We expressed the result in a form equivalent to log 7. = 0.18 [%C] which gives an activity coefficient (?s.) of sulphur only slightly higher than the authors find and certainly within the precision of the earlier work. My second comment concerns the correlation of the thermodynamic findings with atomistics. A rough pic- ture of the atomic arrangement in the liquid solution is rather easily conceived for this particular liquid solution containing iron, carbon, and sulphur. Carbon has a very much stronger affinity for iron than for sulphur. Hence we may conclude that a sulphur atom will but seldom be adjacent to a carbon atom—since this would be a position of high energy. From the metallic radii of iron and carbon we know that six iron atoms pack neatly around one carbon atom. Thus each carbon atom in retaining this shell of iron atoms (which latter may not be replaced by sulphur on account of the high energy requirement) decreases the available positions for each sulphur atom by six. Hence each atomic percent of carbon decreases the equilibrium sulphur content by 6 pct (of itself). Or, at low concentration each atomic percent of carbon increases the activity coefficient of sulphur by 6 pct. This is in good agreement with the observed increase (6 or 7 pct at low carbon content). It is indeed gratifying to find a case where, by such simple reasoning, quantitative agreement is found between precise data and the modern picture of the atomistics of the metallic state. J. P. Morris (authors&apos; reply)—We would like to point out that there is an error in the equation on p. 322 of the paper. The third equation should read: ½S2 (gas) + H2 (gas) = H2S (gas) The authors wish to thank everyone for the interest they have shown in the paper. In regard to the general observation in blast furnace practice, that the sulphur content of the metal is lowered by increasing the temperature, Dr. Richardson is correct in stating that the cause can be attributed only in part to the increase in activity coefficient of sulphur resulting from the rise in carbon plus silicon content of the metal with rise in temperature. However, this factor is probably an important one. The results of one experiment, performed since this report was written, indicate that at a constant temperature the addition of silicon to a melt saturated with carbon causes an increase in the activity coefficient of sulphur even though the carbon solubility is lowered. In this test, 2.5 pct silicon was added to a melt saturated with carbon and maintained at 1400°C. Although the carbon content dropped from 4.85 to 4.1 pct, the activity coefficient of sulphur was increased by about 20 pct.

Jan 1, 1951

By R. Maddin

IN analyzing the relation between the orientation of new grains and that of the deformed matrix of axially extended and recrystallized single crystals of face-centered cubic metals, a two-stage rotation process" is generally used where the first rotation is made in order to account for an "adjustment of orientation to the environment of strain."&apos; It has been argued that in spite of the difference of orientation, which may amount to as much as 12" (in a brass),&apos; between the octahedral plane as observed in the parent lattice and in the recrystallized grain, it is believed to be a common plane in the sense that it constituted the nucleus in the parent strained crystal from which the new grain grew.&apos; A possible source of the deviation in orientations of a common pole in the new grain and that of the deformed single crystal matrix from which it has grown may be found in the distribution of strain resulting from the plastic deformation. It might be expected in view of the incongruent nature of shear&apos; that the perfection of the octahedral plane along which glide has occurred is disrupted and that this disruption constitutes the strain from which nuclei of new grains can grow during recrystallization. Evidence for the existence of strain along glide planes was first detected by Taylor" in 1927 and substantiated by Collins and Mathewson&apos; in 1940. In their investigations, however, the deformed single crystalline specimens (aluminum) were cut mechanically along the glide planes followed by mechanical polishing. X-ray exposures (glancing angle) of only 8 min with filtered radiation were used. It was later shown&apos; that this type of surface preparation did not remove with all certainty the mechanically disturbed surface. It was felt that a re-investigation of this phenomenon using more refined techniques might reveal a more correct extent of the strain resulting from the deformation which might correlate the deviation of the common pole of the recrystallized grain with the acting slip plane of the matrix crystal. In accordance with these thoughts, a single crystal of a brass (70/30 nominal composition) M in. in diam x 5 in. long, tapered as in previous experiments,&apos; was extended and carefully documented with respect to elongation and shear. Disks about % in. thick paralle&apos;l to the primary slip planes were cut from the specimen by means of an etch cutter." These disks represented volumes of the specimen which had been extended 0, 5, 10, 15, and 20 pct. Copper Ka monochromatic radiation was obtained by reflecting 35,000 v copper radiation from the c-cleavage face of a pentaerythritol crystal. The monochromatic radiation was collimated and led on to the disk set at the proper 0 angle for reflection from the primary (111) planes. The monochromatic beam was aligned in a plane containing the active slip direction. Following a 10 hr exposure at the theoretical Bragg angle, the disk was reset at 0 + 1°, 0 — 1", 0 + 2", 0 — 2", etc., until no Bragg reflection was obtained. The disk was then rotated 90" about its polar axis, and the same X-ray procedure was used. The results are shown in Table I. It may be seen from the results in Table I that the plastic deformation (20 pct elongation) produces fragments of the glide plane which are rotated or tilted as much as 25 " from the normal position on a purely block slip model. In addition to the large variation in 0 angle in the slip direction, there is a variation in 0 as much as 20" in the direction at right angles to the direction of slip, i.e., <110>. In view of the results shown, it may now be argued that the strain distribution finds its origin in the incongruent nature of the slip process.&apos; The use of the two-stage rotation process seems valid in attempting to explain the relation between the orientation of recrystallized grains and the matrix from which they have grown. Acknowledgment This work was sponsored by the ONR under Contract Number N6 onr 234-21 ONR 031-383. The author would like to thank N. K. Chen for reading and correcting the manuscript. References &apos;R. Maddin, C. H. Mathewson, and W. R. Hibbard, Jr.: The Origin of Annealing Twins. Trans. AIME (1949) 185, p. 655; Journal of Metals (September 1949). &apos;J. A. Collins and C. H. Mathewson: Plastic Deformation and Recrystallization of Aluminum Single Crystals. Trans. AIME (1940) 137, p. 150. eN. K. Chen and C. H. Mathewson: Recrystallization of Aluminum Single Crystals After Plastic Extension. Unpublished. 4 C. H. Mathewson: Structural Premises of Strain Hardening and Recrystallization. Trans. A.S.M. (1944) 38. :&apos;C. H. Mathewson: Critical Shear Stress and Incongruent Shear in Plastic Deformation. Trans. Conn. Acad. of Arts and Science, (1951) 38, p. 213. "G. I. Taylor: Resistance to Shear in Metal Crystals, Cohesion and Related Problems. Faraday Soc. (1927) 121. &apos;R. Maddin and W. R. Hibbard, Jr.: Some Observations in the Structure of Alpha Brass After Cutting and Polishing. Trans. AIME (1949) 185, p. 700; Journal of Metals (October 1949). &apos;R. Maddin and W. R. Asher: Apparatus for Cutting Metals Strain-Free. Review of Scientific Instruments (1950) 21, p. 881.

Jan 1, 1953

By R. T. O’Brien, J. M. W. Mackenzie

A microelectrophoresis technique has been used to measure the zeta potential of quartz over a range of pH and Ni (11) and Co (Ilj concentrations. Results have been discussed in terms of adsorption of Ni (11) and Co (11) cations and hydroxide precipitates. Possible relationships between the experimental results and the formation of lateritic nickel deposits have been discussed. The adsorption of metallic cations to the surface of silicate minerals is of significance in many industrial and natural processes. In an earlier publication,&apos; the adsorption of Fe (111) to the quartz surface, a phenomenon of importance in flotation, was studied qualitatively using microelectrophoresis techniques. This paper reports the extension of this work to an investigation of the adsorption from aqueous solution of Co (11) and Ni (11) to the quartz surface. The adsorption of these metals was of interest for two reasons; firstly, the importance of such an adsorption process in the formation of nickel deposits by the lateritization of nickeliferous rocks, and secondly, the comparison of electrophoresis data for these metals, whose hydroxides precipitate in the pH range 7-8, with similar data for Fe (111) where the hydroxide first precipitates at pH 2.8. The development of laterites is essentially a near-surface geological process involving vertical and, in part, horizontal redistribution of elements derived from rock-forming minerals. This redistribution of elements leads to the formation of layers within the lateritic profile which are enriched in one or more of these elements and, depending on the nature of the original rocks, continued lateritization may give rise to iron ores, bauxites or nickeliferous laterites. The mechanisms discussed in this paper deal with the last mentioned type of deposit although the considered factors are applicable to laterites in general. Nickeliferous laterites are derived from basic and ultrabasic rocks containing ferro-magnesian silicates. These rocks may be partly or wholly converted to serpentinites. Besides their high Mg, Si and Fe contents, they also contain small amounts of Mn, Al, Cr, Ni, Co, Cu and Zn. The nickel content is usually near to 0.2-0.3%, but for economic use this must be increased during lateritization to over 1% and preferably over 2%. The zone of nickel enrichment is usually at some depth within the lateritic profile. Unpublished work by Mr. O&apos;Brien on nickel-bearing laterites in eastern Australia indicated four visually different types of material which were separated from crushed samples under a stereo-microscope. Although chemical analyses indicated that all four types of fragments contained 2-4% nickel and smaller amounts of cobalt, X-ray diffraction and optical studies revealed only quartz, hematite and chromite as well as, in one of the types, a serpentine mineral. No distinct, nickeliferous minerals were detected. Furthermore, it was possible to extract some 60% of the nickel content of the laterites with cold 0.5N hydrochloric acid. It was therefore postulated that much of the contained nickel was present as amorphous, adsorbed material. In considering this fact, as well as the problem of the actual method of transfer and fixation of elements within the lateritic profile, it was further postulated that the transfer of these elements probably took place partly as solutions and partly as colloids and that the fixation of these was caused by adsorption and flocculation. The existence of nickel in solution in water draining from serpentinites has been confirmed by Smurov.2 Although we have no evidence for the transportation of nickel in the colloidal state, it is well accepted that colloids are important in the formation of laterites. Previous work by Mr. Mackenzie&apos; has already indicated that iron may be adsorbed on quartz under conditions which could be expected in a lateritic profile, but no information was available for nickel or cobalt. Although adsorption possibly also takes place on minerals other than quartz, the latter is significant because silica is an important constituent of the silicate parent rocks. During lateritization, it is released to form free quartz and it is likely that it is initially extremely fine-grained. This would provide abundant opportunities for adsorption and it was de-

Jan 1, 1970

By Donald B. Evans, Robert D. Pehlke

The solubility of nilrogen in liquid binary alloys of iron with Litanium. zivconium, columbium, vanndiurn, and tantalum was measured for alloy composiLions up to the solalbility limils of lhe alloy nitrides. All five alloying agents were found to decrease markedly the activity coefficient of nitrogen in liquid ivon. The metal/nitvogen mole ralios in the alloy nitrides formed were generally .found to be slighlly greater than 1.0, but in no case greater than 1.5. From the experimental data, the standard free energies of fortmation of titanium and zir-conium nitrides have been calculated for the Lemperaluve range 1550° to 1750 C. The solublily Products for columbium, tantalum, and vanadium nitrides are also reported. A number of research investigations have examined the effect of refractory metals on the solubility of nitrogen in liquid iron. Although data on zirconium are not available, investigators are in agreement that titanium, vanadium, columbium, and tantalum markedly increase the solubility of nitrogen in liquid iron. This fact alone makes desirable the acquisition of thermodynamic data for these elements in liquid iron. Since refractory metals are known to be stable nitride formers, they have been suggested as steel denitrifying agents, and some of their nitrides have recently been considered as containment materials for liquid iron and iron alloys. Most available thermodynamic data for these metals relate to their dilute concentrations, but effective thermodynamic treatment of these applications requires data at concentrations near the solubility limit of the alloy nitride. Although some work has been done at relatively high alloy concentrations in liquid iron (particularly for vanadium 2,3 and titanium 2,4), the results have been somewhat contradictory. Disagreement may be partly attributed to the fact that the compositions of most refractory metal nitrides have been shown to be nonstoichiometric, and to vary 2,5-8 depending on the temperature and nitrogen gas pressure with which the solid nitride phase is in equilibrium. One purpose of this study consequently has been to determine the compositions of the refractory metal nitrides precipitated from a liquid iron solution. EXPERIMENTAL PROCEDURE Rao and Parlee2 and Evans and Pehlke 9 have discussed the technique for measuring the solubility product of an alloy nitride phase in liquid iron by finding the point of departure of the nitrogen solubility from Sieverts&apos; law. The method consists of measuring the solubility of nitrogen in a melt of iron containing a known concentration of a second metal as a function of the nitrogen gas pressure over the melt. In this study the second metal was one of the refractory metals titanium, zirconium, columbium, vanadium, or tantalum. When the nitrogen pressure at which the refractory nitride forms is reached, a deviation of the measured solubility of nitrogen in the melt from Sieverts&apos; law is observed in the form of a "pressure halt." The concentration of nitrogen in the melt associated with this breakpoint in the nitrogen-absorption curve is then used to calculate the nitride solubility. The Sieverts method was used to measure nitrogen solubility as a function of nitrogen pressure and temperature. The experimental equipment for this technique has been previously described in detail. 1,9 Charge materials used were vacuum-melted high-purity iron (Ferrovac-E) and the best commercial grades of the refractory metals obtainable (in all cases at least 99.8+ pct pure). Recrystallized alumina crucibles were used to hold all melts except those containing zirconium, for which zirconia crucibles were necessary. Temperatures were measured by a disappearing-filament type optical pyrometer sighted vertically downward on the melt surface through a 1/4-in.-diameter sight hole in the crucible lid. By means of a technique previously described, 9 in which the refractory-metal nitride was precipitated at one temperature then redis-solved by raising the temperature 50°C and precipitated again at a higher temperature, it was possible to obtain data over a temperature range of up to 200°C on a single melt. It was found that this technique could not be used with melts containing zir-

Jan 1, 1965

By R. G. Ward, A. E. El-Mehairy

A technique was developed to calculate the density of liquid metals from the profile of a weighed levitated drop obtained by emitted light photography and calibration. The density of liquid copper was determined over the temperature range 1370" to 2100°K and expressed with the equation: The molar volumes and thermal coefficients of expansion are calculated. Copper, upon melting, was found to expand 3.34 pct. A knowledge of the density of liquid metals is essential as it is a parameter appearing in most theories of the liquid state. The liquid density is also necessary for the calculation of the commercially important contraction occurring on solidification. Unfortunately good density values are rarely available and the present work was undertaken to establish a new method of density determination free from the limitations of the existing methods. For liquid metals with high melting points, the variation and the limited number of density values reported in the literature have been caused primarily by difficulties in technique, a matter which has been adequately discussed by Urbain.&apos; In all the methods used for measuring the density of the high-melting liquid metals there are sources of error, and corrections have to be made. For example, in the method of balanced columns, the formation of gas bubbles in one or both arms was a great source of error. In the pyknometer3 and immersed-sinker methods, corrections of certain volumes for thermal expansion to the operating temperature exceed 4 pct. In the maximum-bubble method5 a correction for the thermal expansion of the bubble-tube is used (about 1.6 pct); a second correction takes into account the change in the volume of liquid displaced by the bubble-tube (about 3.5 pct). Another method used is based on the shape of a drop of liquid, at rest on an inert refractory plaque, obtained photographically or radiographi-cally. The volume is calculated from the shape, which is sensitive to the surface tension and supporting material, by some intricate empirical relation. The drop contour changes with 90 deg rotation of the support.7 The application of all methods is limited by reaction between liquid metal and the apparatus. The successful stabilization of a mass of liquid metal during levitation melting8 afforded a technique for measuring the density of liquid metals out of contact with solid materials. The technique was developed by using copper as the density of liquid copper has already been studied extensively, thus allowing comparison with the new method. It consists of calculating the volume from the dimensioned profile of the levitated drop obtained by emitted-light photography and careful calibration. The molten egg-shaped drop spins around the magnetic axis of the coil (lined vertically) at a speed which seems to increase with increasing temperature. The method does not involve corrections and the experimental setup allows the use of vacuum or special atmospheres. The maximum operating temperature is limited by excessive evaporation of metal from the droplet. EXPERIMENTAL Levitating System. A stabilizing ring was used in conjunction with a 3-turn levitating coil energized by a 450-kc per sec, 10-kw Toccotron with a high current-low voltage output stabilized to f 1 pet.&apos; APyrex glass tube with a Pyrex Optical flat window inserted through the coil and ring allowed the use of special atmospheres during levitation melting, as shown in Fig. 1. Optical System. Fig. 1 shows the optical arrangement used to photograph the profiles of the drop, parallel and perpendicular to the vertical spinning axis, simultaneously on the same frame of a high-speed 35-mm film. The optical system was adjusted to avoid any distortion of the profiles and to ensure that both profiles are in focus. The length of path from object to objective was about 30 cm, and a magnification factor close to 1 was obtained with the single-lens reflex-camera system. Temperature Measurement and Control. In operation, the specimen temperature was constant to 5 C for a fixed power input to the levitating coil and fixed rate of gas flow through the tube. The temperature was measured by an automatic two-color pyrometer (Coloratio) checked at the melting

Jan 1, 1963

By Adrian C. Dorenfeld, Theodore Balberyszski, Strathmore R. B. Cooke

This paper reports results of studies of sulfidiza-tion of base-metal oxides and silicates with gaseous sulfur, hydrogen sulfide gas and pyrite and of their subsequent flotation with xanthate collectors. It has been established that a 100% conversion of the oxides of lead, zinc, copper and manganese into their respective sulfides is possible and is a function of reaction time and temperature. Sulfidization of chrysocolla (with malachite and azurite inclusions) resulted in a product containing covellite, chalcocite and digenite in proportions depending on conditions of sulfidization. Reacting cassiterite with gaseous sulfur, H2S or pyrite at various reaction temperatures resulted in its partial conversion to a tin sulfide. Flotation of the products of sulfidization indicated that their behavior is similar to that of natural sulfide minerals, the recovery being a function of the con-version of the oxides to their respective sulfides. The gradual depletion of high-grade sulfide mineral deposits has turned the attention of the mineral industry to the recovery of metals from the oxides and silicates. Anionic (fatty acid) and cationic collectors have in some cases made flotation of nonsulfides possible, although, in general, flotation of oxide ores is not as yet an economic process. Consequently, many attempts have been made to sulfidize the surface of the relevant oxide mineral and thus make it amenable to to In recent years, Bautista and sollenberger4 have investigated the conversion of a number of oxides to sulfides by reacting them with molten sulfur. This paper presents the results of .investigations carried out at the School of Mineral and Metallurgical Engineering at the University of Minnesota to study the flotation characteristics of some sulfidized minerals. It is divided into two parts: The first describes the sulfidization of a number of oxides and a silicate, and the second presents the flotation behavior of the products of sulfidization. SULFIDIZATION OF METAL OXIDES AND SILICATES Experimental Procedure: SULFIDIZATION WITH HYDROGEN SULFIDE GAS — Sulfidization with H2S gas was carried out in a horizontal tube furnace (Fig. 1). The temperature of the furnace was regulated by means of a Variac and determined with a chromel-alumel thermocouple. The constant temperature zone in the furnace was about 6 in. in length, and it was within this zone that the experiments were carried out. The gases employed were supplied from standard compressed gas cylinders, and passed through a glass-wool filtering tower before entering the Pyrex reaction tube. Gaseous products were bubbled through a water tower (used as a flow indicator) and excess H2S was burned off at the end of the outlet tube. Samples of reagents or minerals were placed in a 3-in. Alundum boat and inserted within the constant temperature zone of the furnace. Nitrogen gas (6 ppm O2 content) was passed through the tubes at room temperature to remove air in the tube, and continued to pass while the furnace was heating up. When the required temperature was reached, H2S was allowed to enter the tube and the supply of nitrogen was shut off. At the end of the reaction period, the reverse procedure was carried out, the samples being cooled to room temperature in a nitrogen atmosphere. The flow rate of H2S gas was maintained fairly constant in all experiments, although the rate was not determined. SULFIDIZATION WITH SULFUR POWDER - To study the sulfidization of minerals with sulfur (liquid or gaseous), samples of the mineral, together with a measured quantity of sulfur powder, were placed in a stainless steel (SS316) reaction vessel (Fig. 2). The reaction vessel was heated in a vertical resistance coil furnace, the temperature being regulated through a Variac. At the end of the experiment the vessel was cooled to room temperature before the sample was removed. Cooled products were leached with CS2 to remove any free sulfur. SULFIDIZATION OF TIN CONCENTRATES - Fifty gram samples of sulfidized tin ore were prepared by mixing -48 mesh Bolivian tin concentrate with -48 mesh Ottawa sand in various proportions and sulfi-dizing these samples with H2S in the horizontal tube

Jan 1, 1969