Search Documents

By H. L. Hartman

The drop tester has proved an invaluable tool for the investigation of percussion drilling in the laboratory in "slow motion". It has allowed the process of rock penetration by impact to be studied a single blow at a time. In the present work, the relation of cratering to indexing has been determined under conditions simulating those in the bottom of the hole at atmospheric pressure. Indexed blows form craters which are influenced by others adjacent to them. Two unique effects are involved: (1) the provision of additional free faces in proximity to the point of impact and (2) the creation of subsurface damage by the previous blow(s). Both have a pronounced influence on the volume of rock removed per blow, which governs the rate of penetration in actual drilling. The emphasis in this study was placed on determining effects of index distance and impact energy on crater volume when blows were struck on a previorusly "drilled" or damaged surface, a situation most representative of down-hole conditions. The results indicated that (I) the optimum index distance on a damaged surface is greater than on a fresh, undamaged rock surface; (2) the volume of rock broken at optimum index distance is about the same for both surface conditions with die-shaped chisels but tends to be greater on a cratered surface with wedges; (3) the optimum index distance and maximum crater volume are proportional to the energy level; (4) at a given energy level, the volume of rock broken by dies generally exceeds that by wedges; and (5) maximum crater volume varies, approximately, inversely with width of die but is nearly independent of included angle of wedge. INTRODUCTION This is the third of a series l,2 of papers reporting on one phase of a continuing program of drilling research being conducted in the Rock Mechanics Laboratory at The Pennsylvania State U. The phase under consideration is crater geometry — blow energy relations in percussion drilling. While the previous papers have discussed mainly craters produced by single blows, indexed-blow studies are the subject of this paper. The basic mechanism of drilling under study here — that of penetration of a chisel-shaped bit subjected to impact — is the one employed in probably 90 per cent of all rock drilling in mining, percussion drilling. It also forms the fundamental action in nearly all oil well drilling with the so-called rotary (roller-bit) method. Here, the action is more complex, however, and may in actuality comprise rotary-percussion drilling. Certainly, the down-hole air and mud hammer drills, which superimpose percussion on rotation, belong in this latter category. In any event, impact blows constitute one of the principal mechanisms in the vast majority of drilling, mining or petroleum, and it is essential in drilling research to study percussion in all its basic aspects. Percussion drilling can be simulated in the laboratory by means of an impact drop tester. Striking one blow at a time with chisel-shaped bits, the drop tester permits study of most of the parameters in the drilling process except blow frequency and the interrelationship of certain variables. Single-blow craters, the simplest to produce, allow the determination of basic relationships, such as volume vs blow energy; while indexed craters most closely resemble the action in real drilling and provide data for the establishment of optimum operating criteria. Indexed-blow craters are those which are influenced by others in proximity. The simplest case to visualize, and the one studied in detail here, is that in which a given crater is formed adjacent and parallel to a previous crater, such that the second crater breaks into the first. A more complex situation usually exists downhole, where indexing is achieved by rotation of a radial-winged or rolling-cutter bit. But, admittedly, the phenomenon of indexing is more likely to be understood eventually if it is first studied in its simplest form, that related to parallel craters. Limited research has been conducted on indexed blows. The most complete study was that by Simon, 3,4 who proposed universal indexing curves to relate the important variables. His work, however, was conducted entirely with rows of craters formed on a

By J. O. Edstrom, G. Bitsianes

Parabolic rate constants were determined for the formation of wiistite by the solid state reaction between magnetite and iron. The reaction was diffusion controlled and inert marker studies indicated that the mass transport through the wiistite layer was accomplished by means of iron migration. Relationships between rate constants and self-diffusivities are discussed. The transport capacity for iron through dense wustite layers was found to be sufficient to carry on reduction, even in gaseous reduction processes. REDUCTION of iron oxides has been the subject of many investigations. Most of the work, however, has been done on rather crude material and there have been difficulties in correlating the data on a quantitative basis. The reverse process of the oxidation of iron has been studied more thoroughly and usually by starting from the pure metal. As a result, the mechanisms of oxidation are now fairly well known.It has generally been found that the oxidation of metals follows the so-called parabolic 1aw;Q hat is, when the oxides are formed as dense layers, their thicknesses are proportional to the square root of the reaction time. This parabolic law follows directly from Fick's first law of diffusion The flux, J, is defined as the quantity of diffusing substance passing per unit time through unit area of a plane at right angles to the direction of diffusion. This flux is proportional to the concentration gradient of the diffusing substance, and the factor D, known as the diffusion coefficient, is introduced as the proportionality factor with dimensions of (length)'/time. If the flux is measured as the increase of thickness of the oxide layer (Ax) per unit time (t) and the assumption is made that the concentrations of the reactants at the phase boundaries of the layer are independent of time, Eq. 1 reduces to Integration of this expression yields the parabolic function ax = k . t. [31 The product of the diffusion coefficient and the concentration difference across the oxide layer is included in the constant k. When iron is exposed to a highly oxidizing atmosphere, the oxide phases are formed normally in a topochemical fashion, i.e., the interfaces between the phases maintain parallel positions to the original surface of the specimen. Above 570°C, the phases are orientated usually in the order of iron, wiistite, magnetite, and hematite, a condition in conformance with the requirements of the Fe-0 system. Below 570°C, the wiistite phase is unstable and has not been found as a normal constituent in the oxidation products of iron. There is a strong probability that continuous layers of the solid oxides are formed as the specific volumes of the phases increase in direct order from iron to hematite.' , ' Regarding mass transport through dense solid oxide layers, Wagner' has postulated that diffusion in oxides generally may be interpreted as migration processes of ions and electrons. There must be normally a concentration gradient across the growing oxide layer for diffusion to occur. This condition requires that there be deviations from the ideal stoi-chiometric composition of the oxide and accordingly deviations from the strict order of an ideal lattice. Such "lattice defects" include interstitial ions, cation and anion vacancies, quasi-free electrons, and electron holes and are decisive for all migration processes.' Cations, anions, and electrons all may have some mobility in the oxides but the movement of one of the particles generally far exceeds that of the others. Previous work', 1,2,7 has shown that during the oxidation of iron the migration through the wiistite layer, and probably also the magnetite layer, is confined to the movement of iron ions. Migration through hematite, however, has been found to take place by oxide ion movement. These behaviors are in direct agreement with the type of vacancies present in the respective oxides. Reduction of Iron Oxides The gaseous reduction of iron oxides, like the oxidation of iron, takes place in a topochemical fashion at distinct interfaces between the appearing phases."-'" Porosities might be expected in these reaction products, since their specific volumes are less than that of the starting material. Frank and van Der Merwe" have shown, however, that it is theoretically possible for nonporous layers to form if the degree of misfit in specific volume is less than about 15 pct. These aspects on porosity formation

Jan 1, 1956

By J. M. Uys, T. B. King

The solubility of water in silicate melts of various compositions was measured. The basicity of the silicate did not appreciably affect the water solu-bulity at low-base content (acid compositions). Near the orthosilicate composition the solubility increased with basicity for silicates in which the cation displayed a weak ion-oxygen attraction and apparently decreased for those in which the cation showed a strong ion-oxygen attraction; metasilicates of the former class dissolved more water than those of the latter. Temperature had little effect on water solubility. The experimental results are interpreted on the basis of two modes of solution, the contribution of one decreasing, and that of the other increas -ing, with increased melt basicity. In the former, solution occurs through interaction with doubly-bonded oxygen atoms and in the latter, through interaction with singly-bonded oxygen atoms, or, in very basic melts, through reaction with free oxygen ions. THE hydrogen content of a steel melt is in a large measure determined by water dissolved in the slag. In some glasses water may be a major cause of "seeds". Water vapor in the furnace atmosphere is the primary source in both instances. A knowledge of the mechanism of water solution in silicate melts should help in assessment of practical methods for its control in steelmaking and glass refining. Walsh et a1.l measured the water content, expressed as hydrogen, of 40 pct lime-20 pct alumina-40 pct silica and 62 pct manganese oxide-38 pct silica melts as a function of the steam partial pressure, in equilibrium with the melt. Tomlinson 2 and, also, Russell3 investigated this relationship for a molten 30 pct soda-70 pct silica glass. In all three investigations, the solubility of water was found to be proportional to the square root of the partial pressure of steam. Moulson and Roberts 4 confirmed this relationship for a silica glass. On the basis of the square root relationship, Tomlinson2 and Russell3 interpreted the solution reaction as "network-breaking", similar to that expected on the addition of metal oxides to silica. Walsh et al.' postulated two possible modes of solution, one the mechanism suggested by Tomlinson and Russell and the other the reaction of the water molecule with an oxygen ion to form hydroxyl ions. These two modes of solution suggest opposite effects of melt basicity on water solubility. However, little appears to be known about the effect of melt basicity on water solubility. Walsh et a1.l found, in the lime-silica system, that the water content increased slightly with increased basicity. As these authors pointed out, this does not appear to be in accord with their further observation that slags containing little or no silica dissolve very little water. Kurkjian and Russell5 measured the effect of basicity on water solubility in alkali silicates in the composition range 15 to 45 mole pct alkali oxide. They found a minimum in the water content at about 25 mole pct alkali. This was interpreted on the basis of two concurrent solution reacZions; one in which solubility was proportional to the activity of doubly-bonded oxygen and, in the other, proportional to the activity of singly-bonded oxygen. The present work was aimed at establishing the effect of basicity on water solubility in silicate melts over as wide a range of compositions as practical. APPARATUS AND EXPERIMENTAL PROCEDURE The silicate melt was equilibrated with a "carrier-gas" of accurately known water content, quenched, and analyzed for water by a vacuum fusion technique. Some pertinent details of the equilibration procedure, analysis technique, preparation, and handling of the silicates are given below. Gas-Silicate Equilibration. The apparatus used to equilibrate the melt with the gas mixture was similar to that used by Walsh et al.' but with some important modifications.6 Purification trains were provided for nitrogen and hydrogen; whenever air or oxygen was used as carrier gas the nitrogen purifiCation train was used with the copper furnace at room temperature. Gas flow rates were measured with capillary flow meters; bleeders filled with a mixture of dibromo and tribromo ethyl benzene (density about 2 g per cc) were used for convenience in controlling flow rates.

Jan 1, 1963

By N. Piret, B. Shoukry, S. Buntenbach

Traditional or artisanal goldmining, also known as small scale goldmining, has a strong and probably a negative environmental impact. The processing methods applied are very frequently a source of severe pollution due to the emissions of mercury by the extraction of gold by means of amalgamation as well as the emissions of cyanide through cyanide leaching of gold bearing ores. The emissions find their way into the environment and contaminate soils, sediments, water and atmosphere. Abnormal concentrations of mercury and cyanides in waterways are known to occur year after year destroying irreplaceable regions of the world. Mercury and cyanide compounds are highly toxic and may directly create permanent damage to the whole ecosystem. Existing methods for recycling of mercury and for decontamination of mercury and cyanide contaminated tailings are not customary applied in small scale mining and are ineffective as well. Based on investigations of traditional and small size goldmining, this paper presents: -processing methods of gold and discarded tailings under consideration of environmental protection; -figures on actual situation; -recommendations for equipment; -some decontamination methods for mercury and residual cyanide. Mineral Processing methods in traditional gold mining Gold is usually existing in its ores as the metal alloyed with metallic silver and perhaps copper. The element may occur in the form of: -native gold -inclusions also of microns or submicroscopic size metal sulfides (auriferous) such as pyrite, pyrrhotite, stibnite, arsenopyrite and galena -combined as telluride or sulphotelluride. The separation process selected depends on whether the gold can be freed from its unfavorable associations (e.g. gangue) at a sufficiently coarse grain-size, or whether it is carried in a heavy sulfide which can be freed similarly. The usual practice is to concentrate the goldbearing mineral at a relatively coarse grain-size and to regrind the ore if necessary. The gold content is concentrated by secondary or tertiary gravital methods or is extracted by chemical methods (amalgamation, cyanidation etc.) Gold, even when of fine grain-size, settle readily due to its high specific gravity from pulps in which the main gangue mineral is quartz or silicates. Amalgamation is the process of separating gold and silver from their associated minerals by binding (entrapping) them into a mixture with mercury. The cyanide process is applied to separate gold or gold-bearing compounds by dissolution from the finely ground ore (CIP, CIL, RIP), or as heap leaching. The dissolved gold is separated from the solids and the metal-rich or pregnant solution is then treated to recover its gold. Gold is also recovered by flotation methods. This process is widely used in treating base metal ores and in separating various sulfide components of ores, as well as in removing the barren gangue. The gold usually associates with a specific product in a sequence of flotation operations and is recovered subsequently in the smelting of the sulfide concentrates and refining of the metallic products, or by cyanidation of the roasted concentrates. Froth-flotation can be applied to separate gold and sulfide minerals from a finely ground pulp. The Amalgamation Process Amalgamation is the main method for the recovery of gold in traditional mining and is applied for the extraction of gold from placers as well as primary ores. The mineral technology used depends on the nature of ore deposits. In winning gold from solid ore, the matrix of minerals and rocks must be crushed and ground to sufficient fineness to liberate the gold. The liberated gold could be treated similar as free gold from placers. Gold is mainly separated from the valueless gangue (barren rock) by utilizing the difference between the density of the impure native metal (density about 16-19) and the gangue (density about 2.5). In simple operations the material is carried by a stream of water down a sluice generally equipped with small transverse barriers (riffles) against which the gold collects. The riffled sluice is the principal device used by artisanal gold miners. Nowadays, spirals as well as centrifuges, such as Knelson separator or Falcon separator, are occasionally applied for gold recovery. Gold may also be recovered from the pulp, by passing it over corduroycovered tables that catch the heavier particles - a method maybe as ancient as gold mining itself. In history, sheep skins were used to catch gold particles in this manner. Furtheron, gravity separation of gold is practiced on jigs, hydraulic traps, shaking tables and

Jan 1, 1995

By P. Datta, L. L. Handy

For a wetting phase displacing a nonwetting phase from a porous medium the distribution of the residual fluid may depend on displacement conditions. Although this subject has been debated in the literature, only a few experiments have been cited to support the various conclusions. Experimental results presented in this paper show that fluid distributions are dependent on imbibition pmcedures. Results agree qualitatively with predictions from the pore doublet model. If the rate of water imbibition is restricted, the nonwetting phase is trapped preferentially in .the larger pores as expected. But if the rate of water imbibition is unrestricted, trapping occurs somewhat more in the smaller pores. These conclusions were deduced primarily from relative permeability measurements. INTRODUCTION Relative permeabilities are known to depend on the saturation history of the porous medium. For either continuously increasing or continuously decreasing wetting phase saturations, however, they have normally been assumed to be single-valued functions of saturation. Severat investigators have compared relative permeabilities measured by different methods and have reported acceptable agreement.1-5 Studies of simple models of the displacement process suggest that the distribution of residual fluids can be influenced by the displacement method. If this is so, relative permeabilities also should depend on the method of displacement. These predictions have not been supported by experimental data. The object of this paper is to investigate experimentally some of the predictions of these model studies. The particular question of importance is whether steady-state and unsteady-state methods should be expected to give the same values of relative permeability. Much of the reported data showing agreement between steady-state and unsteady-state methods have been obtained on un consolidated sand. Johnson, Bossler and Naumann, however, compared steady-state and unsteady-state results for Weiler sandstone and found no significant differences.5 Levine made a detailed study of pressure and saturation distributions for a laboratory waterflood in a consolidated system but made no attempt to calculate performance from steady-state relative permeability data Bail and Marsden in a somewhat similar set of experiments did attempt a comparison of observations with predictions but the results were inconclusive.7 Excluding gravity, two forces affect the distribution of wetting and nonwetting phases during an unsteady-state, immiscible displacement: viscous and capillary forces. If relative permeabilities are indeed the same when measured by steady- or unsteady-state methods, the fluid distributions at the same fluid saturations must be similar for both methods. Furthermore, the implication is that the relation between capillary and viscous forces is the same for both methods insofar as the effect on microscopic fluid distributions is concerned. Unsteady-state displacements are normally run at high rates to maximize the ratio of the viscous to capillary forces. The objective is to reduce the effect of capillary forces on macroscopic fluid distributions. For floods in which the phase which wets the porous medium displaces the nonwetting phase, capillary forces compete with viscous forces in determining fluid distributions.8 The residual nonwetting phase is discontinuous. Competitive aspects of viscous and capillary forces and the resulting effect on water-oil distribution in porous media have been illustrated in an elementary way using a pore doublet model. This model and predictions from it have been discussed at considerable length by Rose and Witherspoon, Rose and Cleary and by Moore and Slobod.9-13 Rose and Witherspoon show that so long as water invades the model at a rate equal to or greater than the free imbibition rate, the water will move through the larger capillary of a doublet first and trap oil in the smaller capillary. On the other hand, if a negative pressure is applied to the water

Jan 1, 1967

By E. P. Sadowski, L. P. Trudeau, C. R. Cupp

The apparent high radiation resistance of two varieties of maraging steel is described and an indication is given of some phenomena that require further study. Two aspects were included in this work: a) effects of neutron irradiation on the room-ternperature tensile properties of 18 Ni (250) maraging steel; b) effects of neutron irradiation on the room-temperature tensile properties and on the impact resistance of 12 pct Ni-5pct Cr-3 pct Mo maraging steel. Subsize tensile and impact test specimens were used. The 18 pct Ni steel was irradiated to a neutron fluence of 3.3 x 10 n per sq cm (>1 mev). The 12-5-3 variety was irradiated to two neutron fluence levels: 1) 1.5 x 10 per sq CTTL (>I mev) 2) 3.1 x 10'9nper sq cm (>1 mev) In all respects both varieties showed unusually high resistance to change in strength and ductility after neutron irradiation. There was no noteuorthy over-aging in fully aged specimens. The aged 18 pct Ni variety showed a 4 pct drop in yield strength upon irradiation with little or no decrease in ductility. The aged 12-5-3 variety showed a 5 pct increase in yield strength on irradiation with a very slight decrease in ductility. The impact transition of the 12-5-3 variety only increased 35 to 45 Co upon irradiation, and the shear energy fracture value for the subsized specimens decreased only half as much as expected frorn experience with conventional steels. THE development of new reactor concepts and nuclear technology now depends to a large extent on the availability of new alloys capable of operating in stringent reactor environments. One of the most important new types of metallurgical material that has been developed in recent years is the maraging steels. This type of alloy is notable for its remarkable retention of toughness at high strength levels. In the course of a research program which incorporated ambient temperature radiation effects studies to determine the mechanisms of strengthening of 18 pct nickel maraging steel,' it became evident that the resistance of the alloy to neutron-induced changes in mechanical properties should be studied. This paper is to present evidence for the apparent high radiation resistance of maraging steel. The experimental program was in two parts: a) Effect of neutron irradiation on the room-temperature tensile properties of 18 Ni (250) maraging steel. b) Effect of neutron irradiation on the room-temperature tensile properties and on the impact resistance of 12 pct Ni-5 pct Cr-3 pct Mo maraging steel, a cobalt-free alloy. EXPERIMENTAL PROCEDURE 18 Ni (250) Maraging Steel. Tensile test specimens were machined to the dimensions shown in Fig. 1 from $-in.-diam hot-rolled bar of the composition shown in Table I. All specimens were austenitized for 1 hr at 1500°F (815°C) in argon and water-quenched. Half of the specimens were then mar aged for 3 hr at 900° F (482°C) in argon. The specimens were irradiated in a fast neutron transformer rod at approximately 120°F (50°C) to a neutron fluence of 3.3 x 10 10 n per sq cm (>1 mev). The irradiation was performed in the NRX reactor of Atomic Energy of Canada, Ltd., at Chalk River, Ontario, Canada. In all cases, the thermal neutron flux was three times as high as the reported (> 1 mev) fluxes. The room-temperature tensile tests were performed with an Instron tensile testing machine operating at a crosshead speed of 0.05 in. per min. The loading frame of the machine, mounted in a hot cell, was remotely controlled. The specimens were tested either

Jan 1, 1968

By J. Handin

Triaxial compression tests with independently applied external confining pressures and internal pore pressures show that the ultimate compressive strengths of representative oil well cements are nearly linear functions of effective pressure — the difference between external and internal pressures on the jacketed cylindrical specimens (to 15,000 psi). The strengths are little affected by the test temperature to 350F (not to be confused with the curing temperature). At an effective pressure of 15,000 psi, strengths are in the rage of 30,000 to 50,000 psi, comparable to those of sedimentary rocks under similar conditions. The cements become very ductile even under low effective pressures; permanent shortenings of 30 per cent or more are attainable without rupture. INTRODUCTION Since the pioneering work of Richart, Brandtzaeg and Brown1 on the failure of cement under combined compressive stresses, it has been recognized that ultimate compressive strength is greatly enhanced by the application of confining pressure. More recently, Mc Henry2 showed that the strength of concrete was a linear function of the effective pressure (the difference between the external confining pressure on a jacketed specimen and the internal fluid pore pressure), at least for a range of 0 to 1,500 psi. The effect of temperature had not been investigated, and no previous systematic triaxial compression testing of naterials used for oilwell cementing seems to have been done. The present work was suggested by the late J. hi. Bugbee3 who stated that "consideration of the common application of high-pressure hydraulic fracturing to the initial completion or recompletion of wells, and the large pressure drawdowns in some producing wells, particularly those in abnormally high-pressure gas-condensate reservoirs, raises the question of what is a suitable cement strength for various completions. The intuitive belief exists that cement strength need be no greater than formation strength. Tests should, however, be conducted at downhole conditions." The ultimate compressive strengths of rocks penetrated by the borehole must rise several fold with increasing depth.4 This marked enhancement of strength is due to the influence of the effective pressure, the total weight per unit area of the overburden less the hydrostatic pore pressure. (The effect of temperature due to the geothermal gradients is relatively small for depths to 30,000 ft.) .A significant comparison of the strengths of rocks and cements at downhole conditions requires knowledge of the confined compressive strengths of cements as well. EXPERIMENTAL PROCEDURES The theory and technique of triaxial compression testing are fully discussed in earlier reports.4-6 Briefly, cylindrical specimens 1-in. long and 0.5-in. in diameter are jacketed in thin copper tubes of negligible strength, placed in the test chamber and subjected to an external confining pressure of kerosene and loaded axially by the piston at a strain rate of 1 per cent per minute. Pore pressures of water (or kerosene) are applied independently through the hollow piston and are maintained constant during the shortening of the specimen, Tests at sensibly 0 pore pressure are arranged so that any free water in the cement can escape to the atmosphere. (If egress of water were denied, pore pressure would rapidly attain the value of the external confining pressure because of reduction of pore space.) The test chamber can be heated for high-temperature experiments. Unless otherwise noted, the cement samples were air dried for about a week. Recorded during a test are pore and confining pressures, shortening and axial differential force (total force less the product of the confining pressure and the area of the piston). True stress-strain curves are constructed by dividing the measured differential force by the actual cross-sectional area of the specimen at a given

Jan 1, 1966

By R. R. Harvey

Recent evidence has indicated that the films forming at crude oil-water interfaces are the result of naturally occurring su,rface-active components in the crude oil rather than oxidation products resulting from exposure of the oil to air. Since the presence of such films may strongly affect the displacement of oil from porous media, a knowledge of their composition and formatiorz is of fundamental importance. In this study, without the assumption of a specific mechanism, film formation is considered to involve the transfer of a weakly surface-active species in solution in the oil to the oil-water interface. The film gas law and the Gibbs adsorption equation may thus he applied to the system. The rigid films which form upon decrease of the oil-water interfacial area are considered a result of the very slow rate of re-solution of the film material into the oil. When the shrinkage of the interface is very rapid, the amount of film material leaving the interface is negligible, and the system may then be treated in the same manner as an insoluble film. The combination of these treatments leads to a new concept of the film factor in which it may he quantitatively related to the concentration of film-forming material at the interface. Suitable experiments can then yield the following information. 1. Original concentration of surface-active species in the oil. 2. The change of concentration with time. 3. Concentration of surface active species at the interface. 4. The change of this concentration with time. 5. Interfacial tension of the system at any time and its variation with time. 6. Equilibriunz concentrations for a given set of conditions. 7. Concentration requirements for solid film formation. 8. Molecular diameter of the adrorbed species. These calculations may be made solely from data taken from measurements on the original oil. While using the pendant drop method of interfacial tension measurement of crude oil-water systems, Bartell and Niederhauser' remarked on the thin, transparent, pliable, solid films or membranes which were often formed at the interface between crude oil and water. As a result of their observations of these films, Bar-tell and Niederhauser concluded: 1. The films are formed by material from the oil adsorbed at the interface rather than by a reaction at the interface. 2. The adsorption of the film-forming material is a rather slow process. 3. There are good indications that the process is reversible; i.e., the film constituents may re-dissolve into the oil. 4. The film will spontaneously spread over any new surface formed. 5. The process of adsorption at the interface is accompanied by a decrease in the interfacial tension of the system. Although they had proved that film formation was not due to a reaction at the interface, Bartell and Niederhauser were unable to demonstrate conclusively whether these film-forming constituents were present in the original reservoir oil or whether they were formed as oxidation products after exposure of the oil to air. Recent evidence seems to point to their presence in the original oil. Although the true nature of the film-forming constituents is still uncertain, these conditions would be fulfilled by the assumption of the presence of a slightly soluble surface-active component in the original oil. This component would migrate to a freshly formed interface because it would thereby lower the free energy of the system. The component at the surface constitutes an expanded monolayer which would become compressed, upon retraction of drop, due to the slow rate of re-solution of the film components into the bulk of the oil. It is possible, by involved extraction processes, to separate or at least concentrate this film-forming fraction. However, using the assumptions made above, the technique of monolayer film study may be applied to reveal much of the nature of the adsorbing material without resorting to an actual separation of the film-forming constituents.

By Robert D. Pehlke, Robert G. Blossey

The solubility of nitrogen in liquid cobalt and a number of dilute cobalt alloys Was measured in the temperature range 1550" to 1700°C at nitrogen pressures to 1 atm. At 1600°C and 1 atm nitrogen pressure, the solubility in pure cobalt is 0.0047 wt pct [3.8 cu cm (stp) per 100 g Co]. The standard free- energy change for the solution reaction 1/2 N,(g) = gout pct in Co) is iF - 10,000 + 5.24 T cal per g atom N. The alloying elements Cv, Cu, Mo, Nb, Tu, W, and V increase the nitrogen solubility, while Al, Fe, Ni, and Si decrease the nitrogen solubility. THE solubility of nitrogen in cobalt was studied previously by Sieverts, Busch and Dodd,2 and Schenck, Frohberg, and Graf.3 Sieverts investigated the solution below the melting point of cobalt, and Busch and Dodd worked with the liquid metal; however, neither study found any solubility for nitrogen in cobalt. Schenck et al, reported a solubility of 0.005 wt pct N in cobalt at 1600°C. Seagle et al. 4 reported residual nitrogen in cobalt after electron-beam melting, although no reasons were ventured for the presence of this interstitial impurity. This investigation was undertaken to clarify these inconsistencies, and to provide additional data on atomic interactions in dilute metallic solution. EXPERIMENTAL PROCEDURE This study was well-suited to the Sieverts' method, which has not changed significantly since its introduction by Sieverts. 5 The apparatus was of the same design as that described by Humbert and Elliott, 6 with a reaction bulb similar to that reported by Weinstein and Elliott. 7 The buret was not water-jacketed, but the measured gas volumes were corrected for small changes in room temperature. The melt temperature was measured by a disappear ing-filament optical pyrometer sighted through a prism onto the melt surface. Temperature calibration was made based on a measurement of the melting point of pure cobalt taken as 1495°C. The difference between the reciprocal of the observed and the true temperatures was assumed to be a constant, neglecting the changes in emissivity with small additions of alloying elements. The total error in gas-volume measurement caused by accuracy limitations in reading the mercury level in the buret, variation in ambient temperature, and variation in melt temperature was about 0.5 cu cm. This represents approximately 10 pct of the total solubility, and is a larger relative error than in previous studies6-' because of the small nitrogen solubilities encountered in the present investigation. The source and purity of the materials used are listed in Table IA. Recrystallized alumina crucibles were used throughout the investigation. Examination of the crucibles after solidification of the melts showed no reaction or penetration. Alloying of the cobalt melt was accomplished with the dropping technique described by Humbert. 6 The investigation was started using cobalt from African Metals Corp. in shot form, but this material was not of sufficient purity and did not yield consistent solubility results. Sherritt Gordon Mines Ltd. cobalt was then used throughout the investigation. In experiments involving alloying elements which could react with oxygen dissolved in the melt, the cobalt was further refined by annealing at 1400°C in a dry-hydrogen atmosphere. This treatment, described by Woolley and Pehlke, 8 markedly reduced the oxygen content. The oxygen and nitrogen analyses of the cobalt used in this study are presented in Table IB. RESULTS Hot Volume. The hot volume was measured prior to each run and was 50 to 55 cu cm (stp) at 1600°C. It increased linearly with increasing pressure and decreasing melt temperature. Pure Cobalt. Measurements of the solubility of nitrogen in pure cobalt and the temperature coefficient of solubility are summarized in Table 11. At 1600°C and 1 atm nitrogen pressure, the solubility was found

Jan 1, 1967

By Margaret N. Maxey

Man's capacity far fretting is endless, and no matter what difficulties we surmount, how many ideals we realize, there is a stealthy pleasure in rejecting mankind or the universe as unworthy of our approval. - Will Durant Until recently, reasons for favoring one or another energy alternative were advanced on the basis of technical considerations and economic realities. However, it is an indication of the cultural climate of our society and growing realization of why energy is our master resource that many citizens have begun to express concern about the social and ethical implications of our energy deci¬sion-making. A vivid indication of this shift toward ethical concerns is reflected in the attention being focused on conservation - even to the point of regarding it as a virtual panacea equivalent to a "free energy resource." Among others, the authors of a publication by Resources for the Future cautions us about the difficulties of defining conservation. They also point out that unrealistic expectations for achieving the high levels of conservation claimed by true believers may boomerang if, at the same time, we are morally required to maintain economic growth and robust productivity for the basic well-being of more people. In its economic meaning, conservation signifies the most economic or cost-effective applications of energy, together with other resources, in a given process or activity. To achieve conservation that is cost-effective, saving energy alone is not sufficient; the cost involved in saving the energy must be no greater than the cost of the energy that is saved. Using its thermodynamic meaning, conservation and efficiency are viewed as constrained by physical laws and measured against ideal limits set by these laws and processes. Since achieving higher levels of technical performance is not without costs, the economic meaning of conservation must be factored into technical possibilities. It is the ethical, equity and environmental meaning of conservation that concerns us here. In its third meaning, conservation consists in moderation as a value which appears inherently worthwhile both in itself and in relation to social choices dedicated to achieving distributive justice. The value of moderation seems predicated on the assumption that natural resources and the environment have fixed, finite, exhaustible capacities for satisfying human needs. Hence norms for moderating human behavior appear to require prescriptions by some authority. Such norms presuppose some agreement on "essential" uses of energy. However, the difficulties of setting behavioral norms loom large, because "... it is as difficult to determine essential energy consumption as to determine what is essential in any other phase of consumption, whether it involves food, clothing, shelter, or recreation." The ethical meaning of conversation is further complicated by a centuries-old argument over the proper exercise of stewardship - i.e., how best to develop natural resources. On the one hand, the preservationist position insists on an inviolate, "hands-off" policy and stands opposed to ongoing development of wilderness areas and mineral resources. On the other hand, the "scientific conservationist" who preaches the "gospel of efficiency" insists on development of resources based on principles of sustained-yield, multiple use and - in the case of competing claims - reserving resources or land for their "higher use." Current confusion reigns among opinion leaders in the environmental movement because they appear to have lost the genius of the original Conservation ethic, developed in the 19th century. They seem to think that conservation is preservation. The question I wish to explore is whether a single-minded, exclusive pursuit of "conservation" in its economic, thermodynamic and preservationist meanings may actually do more harm than good in serving the ethical goals of conservation. There

Jan 1, 1986

By L. W. Reynolds, R. F. Campbell, K. G. Carroll, S. H. Ballard

Based on metallographic and X-ray data probable equilibrium conditions from 1340" to 2400°F are presented for the composition range investigated. These are correlated with investigations of Takei and Kuo. Provision is made for existence of Mo, C and (Fe, Mo)2,C, carbides heretofore omitted in diagrams in this composition range. These carbides and (Fe, Mo),C, in equilibrium with ferrite and austenite, restrict the austenite and austenite + ferrite fields to lower carbon contents and higher temperatures than in the Fe-C system. OK groups of steel of different molybdenum content, but with approximately the same carbon variation in each group, Table I, were studied. The alloys were melted in an acid-lined 30-lb high-frequency induction furnace, and the ingots forged to l-in. rounds, which were then ground to 0.75-in. diam. To minimize chemical segregations a short length of each bar was given a high-temperature heat treatment as listed in Table I. Specimens 0.062 to 0.125-in. thick were thereafter cut from the homogenized bars for heat treatment to determine phase changes in the alloy. Heat treatments were performed in either a lead bath or muffle-type electric furnace, depending upon the temperature required. Maximum temperature variation was * 2" F in the lead bath and * 5"F up to 1900°F and +8"F above 1900°F in the electric furnace. Adequate protection of the specimen from the oxidizing atmosphere in the electric furnace was obtained by sealing the specimen in either a pyrex or a silica capsule which was evacuated or not as circumstances required. For austenitizing followed by quenching to an isothermal temperature, the specimen was placed in a closed-end refractory tube the mouth of which, extending beyond the furnace, was connected to a vacuum pump. The specimen could be withdrawn from this tube and quenched as desired. IDENTIFICATION OF PHASES The principal method of identification of phases was metallographic examination conducted on surfaces well removed from exposure to lead or atmosphere effects during heat treatment. Hardness measurements (Dph/lOkg) were also made on these surfaces. The etching reagents used and their effects are listed in Table II. Martensite and ferrite were readily recognized by their customary appearance after etching with saturated picral or 1 pct nital. The presence of liquid at high temperature was indicated by curved interfaces characteristic of boundaries between solid and melt, by intergranular pools of dendritic areas in a carbide matrix, and by a black network coincident with austenite grain boundaries. Examples of these structures are shown in Figs. l(a) and (0). The types of carbide which were attacked by the electrolytic chromic acid etch and the alkaline KMnO, etch, Table 11, were identified by X-ray analyses of extracted carbides of five alloys. Carbide residue was obtained from a metallographic specimen by etching the specimen for 24 hr in hydrochloric-picric acid in alcohol (grain-size reagent), after which the carbides, standing in relief, were scraped from the surface of the specimen and mounted on a glass slide. Diffraction patterns were obtained with a Philips spectrometer using iron-filtered cobalt radiation. Figs. 2, 3, 4, and 5 illustrate typical etching behaviors with chromic acid and alkaline KMnO,. Chromic acid attacked Mo,C as shown in Figs. 2(a) and (b)-but not (Fe, Mo),C, Fig. 3(b). Alkaline KMnO, attacked (Fe, Mo),C, Fig. 3(c), and also attacked M0,C. In accordance with these behaviors, a typical differentiation of coexisting Mo,C and (Fe, Mo),~ is shown in Figs. 4(a) and (b). The carbide (Fe, Mo),,C, could not be obtained free of other coexisting carbides for etching experiments. The behavior. however. of coexisting carbides identified by x-ray diffraction as Mo,C ind (Fe, Mo),,C, indicate that (Fe, Mo)23C6 is not etched by chromic

Jan 1, 1961

By L. M. Pidgeon, P. G. Thornhill

A LTHOUGH a considerable number of experi--ti mental investigations dealing with the roasting of sulfide minerals have been reported in the past,'"" the behavior of the single roasting particle does not appear to have received the attention it perhaps deserves. This is understandable in that the natural sulfide counterpart of the slab or sheet of metal normally used in high temperature oxidation studies is difficult to obtain and prepare, and is, in most cases, virtually impossible to maintain in one piece at roasting temperatures. The employment, on the other hand, of static aggregations of small particles in masses great enough to permit evaluation of the roasting reactions by means of thermobalances or gas analyses introduces other complications, such as localized overheating, sintering, and variable gas-solid contact. In this investigation a compromise between the above extremes was attempted. Closely sized (e.g., 30 to 40 mesh) particles of natural sulfide minerals were isothermally roasted, out of contact with one another, in an air-swept system. The progress of the roasting reactions was followed by examination in polished section of the treated particles and by X-ray and chemical analysis of their residual sulfide kernels. In this way some conclusions respecting the mechanism of roasting reactions were drawn. Roasting Furnace—The vertical tube furnace used for roasting the sulfide particles had a heated zone 10 1/2 in. long in which four retractable light gage stainless steel trays were suspended. Each tray, and an accompanying baffle, was mounted on a 2 in. lengtn of 3/8 in. stainless steel tubing. These assemblies were axially suspended on a 30 in. length of ¼ in. stainless tubing, by means of which they could be lifted from the hot zone to a water-cooled brass chamber at the top of the furnace. Since each tray unit could slide freely on the 30 in. tube, any desired number of the trays could be retained in the cooling chamber by the manipulation of a horizontal plunger during a momentary withdrawal of the four trays from the hot zone. Although three heating coils, each equipped with variable external resistance, were employed, it was found impossible to avoid a drop of 10o to 15oC between the temperature at the top tray and that of the lower three. Consequently, only the bottom three trays were used for roasting. Temperature readings inside the furnace were made by means of a thermocouple inserted down the tray support tube at tray levels, and a separate thermocouple, inserted adjacent to the middle heating coil, was connected to a Micromax temperature control unit. Experimental Method—The sulfide minerals were obtained in a form as free as possible from gangue and contaminating sulfides, and were crushed and screened to the required particle size range. The tray assembly was kept inside the furnace during the heating-up period and, when a steady temperature had been reached, the trays were withdrawn. Each tray was sprinkled with from 200 to 500 mg of the sulfide grains, and the assembly was lowered into the furnace without delay in order to minimize the time required to achieve the operating temperature. The furnace top was then clamped into position and the thermocouple inserted down the center tube to the required level. It was found that, when this procedure was used, the trays achieved their former temperature within 2 min, after which time the flow of dry air was begun at a rate of 1 liter per min, and timing of the run was started. At the required intervals of time the trays were successively withdrawn from the hot zone and stored in the cooling chamber by means of the retention plunger. On completion of the run the treated particles were removed from the trays to be set aside for examination. The roasted particles were mounted in Lucite on a Buehler press Operating at a temperature of 140°C

Jan 1, 1958

By J. H. Wernick, D. Dorsi, K. E. Benson

A LTHOUGH a considerable number of experi--ti mental investigations dealing with the roasting of sulfide minerals have been reported in the past,'"" the behavior of the single roasting particle does not appear to have received the attention it perhaps deserves. This is understandable in that the natural sulfide counterpart of the slab or sheet of metal normally used in high temperature oxidation studies is difficult to obtain and prepare, and is, in most cases, virtually impossible to maintain in one piece at roasting temperatures. The employment, on the other hand, of static aggregations of small particles in masses great enough to permit evaluation of the roasting reactions by means of thermobalances or gas analyses introduces other complications, such as localized overheating, sintering, and variable gas-solid contact. In this investigation a compromise between the above extremes was attempted. Closely sized (e.g., 30 to 40 mesh) particles of natural sulfide minerals were isothermally roasted, out of contact with one another, in an air-swept system. The progress of the roasting reactions was followed by examination in polished section of the treated particles and by X-ray and chemical analysis of their residual sulfide kernels. In this way some conclusions respecting the mechanism of roasting reactions were drawn. Roasting Furnace—The vertical tube furnace used for roasting the sulfide particles had a heated zone 10 1/2 in. long in which four retractable light gage stainless steel trays were suspended. Each tray, and an accompanying baffle, was mounted on a 2 in. iength of 3/8 in. stainless steel tubing. These assemblies were axially suspended on a 30 in. length of in. stainless tubing, by means of which they could be lifted from the hot zone to a water-cooled brass chamber at the top of the furnace. Since each tray unit could slide freely on the 30 in. tube, any desired number of the trays could be retained in the cooling chamber by the manipulation of a horizontal plunger during a momentary withdrawal of the four trays from the hot zone. Although three heating coils, each equipped with variable external resistance, were employed, it was found impossible to avoid a drop of 10O to 15OC between the temperature at the top tray and that of the lower three. Consequently, only the bottom three trays were used for roasting. Temperature readings inside the furnace were made by means of a thermocouple inserted down the tray support tube at tray levels, and a separate thermocouple, inserted adjacent to the middle heating coil, was connected to a Micromax temperature control unit. Experimental Method—The sulfide minerals were obtained in a form as free as possible from gangue and contaminating sulfides, and were crushed and screened to the required particle size range. The tray assembly was kept inside the furnace during the heating-up period and, when a steady temperature had been reached, the trays were withdrawn. Each tray was sprinkled with from 200 to 500 mg of the sulfide grains, and the assembly was lowered into the furnace without delay in order to minimize the time required to achieve the operating temperature. The furnace top was then clamped into position and the thermocouple inserted down the center tube to the required level. It was found that, when this procedure was used, the trays achieved their former temperature within 2 min, after which time the flow of dry air was begun at a rate of 1 liter per min, and timing of the run was started. At the required intervals of time the trays were successively withdrawn from the hot zone and stored in the cooling chamber by means of the retention plunger. On completion of the run the treated particles were removed from the trays to be set aside for examination. The roasted particles were mounted in Lucite on a Buehler press operating at a temperature of 146°C

Jan 1, 1958

By Fritz Kleiner, Walter Meintrup

On Nov. 4, 1981 A/S Sydvaranger's 1-kt/h (1,100-stph) wet-process, iron ore ball mill completed its first four months of uninterrupted, full-load operation in Kirkenes, Norway. This 6.5-m-diam (21-ft-diam) mill is driven by a gearless ring or wraparound 8.1-MW (10,860-hp) motor at 13.1 rpm-a first of a kind in this segment of industry. This article examines reasons for selecting this type of drive over more conventional schemes, lists specific advantages of such large mills, and describes the installation in Norway. History For almost a decade, good operating experiences have been gained with 28 gearless ring motor drives in the cement industry, driving 2.5 to 4-m-diam (8.2 to 13-ft-diam) tube mills with drive powers ranging from about 3-4 MW (4,000 - 8,000 hp). Why then did the mineral ore processing industry hesitate until 1980 to adopt this successful concept for similar applications on ball, semiautogenous, and autogenous mills? There are a number of good reasons in the eyes of conservative mill builders and operators, the most commonly cited ones are: • No operating experience in this segment of specialized industry. • More severe environmental conditions in the wet ore grinding process. • An indifferent attitude of mill builders and electric motor manufacturers towards new drive technologies. • Limited confidence in solid-state power supply systems, such as frequency converters of the required size. There have been and still are numerous problems associated with low-speed geared mill drives of any kind, especially with individual motor/gear sizes approaching or exceeding about 4 MW (5,360 hp). Every mill builder knows about them, but operators learn to accept them as inevitable. The Decision to Change Three things combined to break this technological stalemate: the courage and progressive spirit of one major iron ore processor in Scandinavia, the cooperation of three experienced manufacturers, and an unusual application problem that could not be solved by any conventional approach. The last factor was surely the decisive one, but the first one does not come as a surprise either. The Swedes near Kiruna and the Norwegians around Kirkenes are experienced ore miners and processors, and much credit goes to them for technological breakthroughs in the industry. At A/S Sydvaranger in Kirkenes, above the Polar circle at about the latitude of Alaska's northern tip, the existing grinding facilities, with a total of 14 100 to 240-t/h (110 to 264-stph) ball mills, can not be expanded. Nevertheless, to increase mill throughput, only installing a larger mill in place of an existing smaller one was a practical alternative. For this replacement, the owners set requirements that seemed impossible to meet: • The old 100-t/h (110-stph) ball mill should be replaced with a new ball mill with 10 times the rated throughput, without significantly impairing the operation of the remaining mills, and without significantly changing the mill building. • The new mill should have a variable-speed drive to ultimately optimize the grinding process by means of a closed-loop process¬computer-controlled grinding cycle, and to minimize the specific energy consumption. • Availability, efficiency, and life expectancy of all new components must be higher than those being replaced. • Inrush-current and harmonic loads on the rather weak electric supply line must be minimized to ensure safe plant operation. All old ball mills at A/S Sydvaranger are the geared type, using single synchronous and wound-rotor, slow-speed motors with ring-and-pinion gears. Operators are familiar with the limitations and problems associated with such drives, and they are aware that the following items become major concerns when drive powers are drastically increased: • Gears are subject to wear and tear, require frequent maintenance, and eventual replacement of major parts. • Gears are sensitive to misalignment, overload, and thermal distortion, limiting their useful life. • On dual or quadruple drives, load-sharing and torque oscillations between motors can be a major reason for concern. • At these speeds, ring-and-pinion gears reach their torque transmission capabilities altogether at around 4 MW (5,360 hp) per motor/pinion. To obtain the desired variable-speed performance of the new drive, the only practical and economical conventional solution would have been a frequency-controlled, low- or medium-speed dual motor drive with about 8 MW (10,720 hp) of power. This, however, was not feasible because of limited floor space. Therefore, bids were solicited for the alternative drive method, the gearless ring motor. General Considerations Why are such large mills considered? After all, one could avoid all the problems by simply staying with smaller mill unit sizes. Under competitive pressures of free markets, however, grinding efficiencies and specific energy consumption become key factors in selecting new equipment. Specific energy consumption of ball mills decreases with increas-

Jan 9, 1982

By G. H. Anderson

H. R. HANLEY*—I have been asked to discuss briefly the development of rotating cathodes for the electrolytic deposition of cadmium. The earliest recorded use of rotating cathodes was by Hoepfner at Frufurt, Germany about sixty years ago. He elec-trolized zinc chloride solution using diaphragms to separate electrodes. In the early experimental work of the Bully Hill Copper Mining and Smelting Co., Shasta County, Calif., rotating aluminum cathodes 4 ft in diam were used in the electrolysis of an acid zinc sulphate solution. Finished cathodes weighing up to 400 lb were produced. Because of mechanical difficulties, this type of cathode was abandoned for zinc, but was later used for cadmium because of the relative smoothness of deposit in comparison with stationary plates with comparable current densities. Cadmium sponge which forms on the cathode at moderate current densities (without special treatment) is entirely eliminated by a slow rotation. The rate of rotation of the cathode has an effect on the mechanical nature of the deposit. A high rate of rotation concentrates the adhering electrolyte on the shaft; a moderate rate appears to concentrate on the cathode a short distance out from the shaft tending to corrode the deposit in the form of a ring. At a very slow rotation (2 to 3 rpm) the adhering electrolyte gravitates nearly vertically, thus avoiding the cutting ring referred to above. The true explanation for the smoother deposits obtained on rotating cathodes may not be given definitely as the numerous factors involved are not thoroughly understood. Smooth deposits are obtained when the orderly growth of the metal crystals in the cathode lattice are disorganized. Thus the crystals form and grow for a very short interval when they are arrested and a new crystal forms. The continued growth of the original crystals provides large crystals and a rough deposit. Also if the acidity of the electrolyte is low, hydrogen gas bubbles adhere to the deposit. As the cathode is rotated the gas surface is brought into the atmosphere where they burst; thus the deposit is made on a surface relatively gas-free. An aluminum hub distance piece was riveted to each aluminum disk 4 ft in diam, slipped on a 4 1/2 in. steel shaft and pressed tight to prevent acid electrolyte seeping through to the shaft. The 9-cathode assembly was supported on insulated bearings. Electrical contact to the shaft was made through what was equivalent to a copper pulley. Sufficiently high conductivity brushes were placed on the face of the pulley to lead the current to the cathode bus bar. The assembly was driven by a link belt contacting a sprocket insulated from the shaft. The lead anodes were semicircular and supported on porcelain insulators placed on the bottom of the cell. Two anodes were provided for each cathode to permit an 8-in. space between them without increasing the ohmic resistance. This ample spacing permitted easy stripping of deposit with the assembly in place. Cathode cadmium was melted under 650 W cylinder oil. After casting, the primary slabs were remelted under molten caustic soda and cast into pencils 1 1/32 in. in diam. Rotating cathodes for deposition of cadmium are used at Risdon, Tasmania, and at Magdeburg, Germany. W. G. WOOLF*—This paper is very-interesting to me because in our work at the Electrolytic Zinc Plant of the Sullivan Mining Co. we had an exactly similar problem—that is, a method of producing cadmium from our purification residue, the recovery of the contained copper as a copper precipitate which could be sent to a copper smelter and the production of merchantable cadmium. It is interesting to me, not knowing of the work of the Risdon people, how closely we approximate them in their main metallurgy, diverging at several interesting steps which I would like to discuss for just a moment. For example, at Risdon they oxidize their purification residue. In our practice we take the current residue as it is produced in the purification department of the zinc plant and process it in the cadmium plant. The only oxidation that it obtains is the oxidation in the presses, the dumping of the presses and the collection and transportation of the residue to the cadmium plant. We find that the leaching of that residue does not necessarily require the oxidation step that the Risdon people evidently find necessary. The discussion of oxidation comes in again in the matter of the treatment of the precipitated cadmium sponge with zinc dust which again at Risdon is oxidized but which we do not attempt to oxidize except as it oxidizes itself in the storage. There is a partial oxidation which cannot be avoided, as Mr. David-sou pointed out, but we make no attempt to attain a complete oxidation and we dissolve the cadmium sponge in the sul-

Jan 1, 1950

By J. Mizrahi, A. M. Baniel, A. Mitzmager, S. Star

This article gives an account of the latest developments in the use of TBE for sink-float separation of silicate minerals. A number of minerals for which the process has been tested and found suitable are reviewed. Specific examples are discussed in relation to the particular problems of sink-float separation and recovery of TBE as compared with non-silicate minerals. The economic aspects are outlined. Silica and silicates comprise the most common and abundant group of minerals, and since they are present in variable amounts in most ores, they constitute an appropriate subject for the review and discussion of the recent developments in the use of TBE for mineral concentration. The silicates considered as a group have an extremely wide range of chemical and physical properties. Some of these properties, which are common to all minerals, are of importance to concentration by TBE and are discussed in some detail in this paper, as well as the development of methods and apparatus for concentration and recovery of TBE and several examples of concentration of silicates. PROPERTIES OF MINERALS WITH RESPECT TO CONCENTRATION BY TBE The properties considered as most important to concentration by TBE are specific gravity, structure, surface and shape. The specific gravity of a mineral is a fundamental property and is constant between very close limits for the same species of different sources if particles are pure and free from cavities or cracks. In many species, however, solid inclusions and changes in chemical composition due to replacement of elements cause variations in the specific gravity. The plagio-clase series of feldspars between albite and anorthite illustrate this point (specific gravity from 2.60 to 2.77). Fig. 1 shows the specific gravity distribution of some of the common silicate minerals.' The highest specific gravity is about 4.7 (zircon) and the lowest is 2.0 (sepiolite), with most of them ranging between 2.6 and 3.5. Although most of the silicates given in Fig. 1 are found as constituents of rocks, those generally considered as rock making minerals are comparatively few. They include quartz, feldspars, nephelite, sodalite, leucite, mica, pyroxenes, amphiboles, chrysolite, kaolin, talc and serpentine. These minerals may appear in igneous rocks as coarse crystals in granites, syenites and diorites or as very fine grained dispersions in basalt and felsite. When the latter rocks occur in an ore, their specific gravities depend on the minerals present and structure. The same is true for the sedimentary and metamorphic rocks (sandstones, shales, gneiss, slate, schists). A comparison of specific gravities for the minerals listed in Fig. 1 with that of TBE (see Table I) shows that the important rock-forming minerals, with the exception of pyroxenes, amphiboles and chrysolite (olivine), lie in the specific gravity range of less than 2.96 and can therefore be separated by TBE. The ore structure is important both in determining the apparent specific gravity and the efficiency of TBE recovery. The structure can be compact (as in

Jan 1, 1963

By A. O. P. Casbarian

An analytical method is developed to determine the variation of the ultimate lateral resistance of a plate in a cohesionless soil with depth. This analysis is based on a modification of Rankine's classical earth pressure theory and the theory of plasticity as applied to soils. The ultimate resistance is defined as the product of the effective stress at the midpoint of the plate, the area of the plate and a dimensionless variable termed the ultimate resistance factor. This variable has been plotted us the depth ratio: i.e., the ratio of of the depth of embedment us the height of the plate. The resistance of a plate may then be calculated using the values af the ultimate resistance factor from the chart provided or the equation may be programmed for use in an analysis of anchor systems in cohesionless soils. It is emphasized that the analysis is semitheoretical. The theory has been compared with experimental results reported in the literature and results indicate general agreement. Actual field tests are necessary to further verify this theory. INTRODUCTION With the exploration for oil offshore in waters all over the world, it is of importance to determine the behavior of the various soils in relation to their ultimate resistance to deformation. Examples of such problems are the holding capacity of anchors and the lateral resistance of piles. Very little information is available in the published literature on the design and performance of anchors, in either cohesive or cohesionless soils. The analysis developed in this report is the first step in obtaining a solution for the determination of anchor holding capacity in a cohesionless material. DISCUSSION The theory used in the analysis is based on the ultimate strength of the soil and is the maximum resistance developed by the plate against further movement. In such a state the elastic deformations are disregarded in comparison with the plastic deformations. Hence, the plate can be considered as completely rigid. The theory of plasticity determines the three unknown stresses at any point by means of two equilibrium conditions for a small earth element in combination with the failure condition. However, the exact solutions can only be carried out in a few simple cases such as, for example, when the rupture or failure lines are straight (Rankine theory) or with spiral and straight rupture lines (Prandtl theory).l Kiitter 2 derived a single equation expressing the variation of the stress in any given rupture line. To utilize this equation, it is necessary to know the stress in the rupture line at a certain point. Unfortunately, this is difficult to obtain unless the rupture line intersects the free surface at a certain angle or when the earth is cohesion-less and unloaded. A method to overcome this is to consider only the boundary conditions at both ends of a rupture line without investigating the equilibrium of the earth above the rupture line. This assumes that the rupture lines meet the surface at statically correct angles, so that boundary stresses may be determined. As Kiitter's equation furnished a relation between these stresses, the unit earth pressure may be calculated at the point where the rupture line meets the wall. Another way in which Kotter's equation may be applied is in investigating the equilibrium of a soil mass above a rupture line. This method assumes that the failure or rupture line is known and that the boundary stresses in the rupture line at the ground surface can be determined. In this case it is possible to determine the earth pressure from the equations of equilibrium.

Jan 1, 1967

By D. S. Tannhauser, I. Bransky

Measurements of the electrical conductivity, the thermal electromotive force, and the deviation from stoichiometry by thermogravimetry were made on ferrous oxide (wüstite) single crystals as well as on poly-crystalline samples in the temperature range of -900" to 1330°C. In the region defined by T 2 1000°C and 1.05 5 O/Fe 5 1.10 the electrical conductivity was shown to be proportional to the sixth root of- the oxygen partial pressure and to be linearly dependent on the deviation from stoichiometry. The absolute Seebeck coefficient of single and polycrystalline wüstite was shown to be independent of temperature in the above region and a p to n transition of the Seebeck coefficient was observed at O/Fe = 1.09 in polycrystalline wüstite. Analysis of the results showed that the predominant defects in wüstite in the above region were doubly ionized cation vacancies. The analysis also ruled out the existence of complexes of the type postulated by Roth, except that below 1000°C there is some evidence of 'association of defects. Of the three oxides of iron (FeO, Fe3O4, Fe2O3) only FeO (wüstite) can exist within a wide range of the ratio O/Fe. This has been shown by several investigations of the phase diagram using for instance chemical analysis of quenched samples'-4 or thermogravimetric measurements. 5,8 Darken and Gurry's1 data for example in the temper- ature range 1100o to 1400°C show that the lowest O/Fe ratio obtainable for FeOl +. is about 1.045 and that the existence range extends to O/Fe = 1.20 at 1400oC. On the basis of detailed analysis of thermogravimetric measurements made by Vallet and Raccah6 the existence of three varieties of wüstite at elevated temperatures was suggested by these authors and by Kleman. It is well-established that wüstite has a NaCl structure with vacant cation sites.3, 8 From a neutron-diffraction study of wüstite samples quenched to room temperature Roth9 concluded that defects in wüstite are mostly complexes composed of two cation vacancies and one interstitial cation in a tetrahedral site. The atomic arrangement in the vicinity of such a defect is similar to that in magnetite, where each occupied tetrahedral site is surrounded by four vacant octahedral positions disposed at the corners of a tetrahedron, so arranged that each vacancy is shared by two tetrahedral cations. Thus there is an average of two vacancies per interstitial. Recent X-ray diffraction measurements made by Smuts10 on quenched wüstite samples confirmed the results of Roth's neutron-diffraction experiments. Roth's model of defects in FeO can be regarded as a solid solution of Fe3O4 in FeO; salmon1' used this defect model to calculate the activity of Fe3O1 in FeO at high temperature and claimed good agreement with the results obtained experimentally by Darken and Gurry.' Each missing cation in wüstite is accompanied by two trivalent cations, thus preserving charge neutrality. The "holes" which differentiate between the Fe 2+ and Fe3' states of the ions in octahedral positions can overcome the attractive field of the cation vacancies, and are then free to move through the crystal as charge carriers. A similar picture holds for COO, NiO, andMnO.l2, 13 Localization of the charge carriers in transition

Jan 1, 1968

By R. F. Domagala, D. J. McPherson

Iodide zirconium was combined with calculated amounts of ZrO2 or master alloys and arc-melted. Annealing treatments were carried out at 21 temperature levels. Metallographic examination of the heat treated specimens permitted construction of the binary phase diagram from zirconium to ZrO2. Oxygen additions to zirconium raise the transformation temperature as well as the melting point. Features of the diagram include the peritectic formation of beta, the formation of alpha directly from the melt, an intermediate phase ZrOB with a' range of homogeneity, and a eutectic between alpha and Zr02. PHASE relationships in the Zr-0 system were determined in the range 0 to 66. 7 atomic pct 0 (ZrO,). Arc-melted alloys were annealed at temperature levels between 600" and 2000°C. Determination of the phase boundaries was accomplished by metallographic evaluation of specimens quenched from the various temperatures. Incipient melting techniques were used to determine solidus curves, and X-ray diffraction work was employed to study the lattice parameters of the a solid solution and the phase ZrO,. Experimental Procedures Westinghouse "Grade 1" iodide zirconium crystal bar (approximately 99.8 pct pure) was employed for the investigation. This material is substantially free of the impurity inclusions characteristic of most zirconium metal. Previous work has shown it to be the most satisfactory grade for phase diagram studies. The zirconium crystal bar, as-received, was coated with corrosion product from autoclave tests by which its grade designation is determined. The bars were sand blasted lightly, pickled for 1 min in a 20 pct HN0,-5 pct HF aqueous solution, rinsed in water and acetone, and dried. The bars were rolled to about 1/32 in. strip, cut into 10 in. lengths, and pickled again. The material was sheared to approximately Y4 in. squares, cleaned with acetone, and stored for use. Two pounds of specially prepared "chemically pure," and 100 grams of spectrographic grade ZrO, were obtained for the preparation of alloys. The "Specpure" ZrO, was obtained from Johnson, Mat-they Co.. Ltd.. and Titanium Alloy Manufacturing Div. of National Lead Co. supplied the other grade of oxide. The "chemically pure" material (henceforth referred to as C.P. ZrO,) was used for the preparation of all alloys employed in the determination of phase relationships. A limited number of alloys were prepared with the "Specpure" oxide to recheck certain phase boundaries. Analyses of the two grades of oxide are given in Table I. The C.P. ZrOI was received in powder form, not suitable for arc melting. Therefore, this material was compressed to wafers 1 in. in diameter and about Vn in. thick. These were segmented and stored for use. The "Specpure" material, in the form of small granules, was suitable for use in the as-received condition. A nonconsumable electrode arc-melting furnace was used to prepare alloys. A water-cooled copper crucible and tungsten-tipped electrode were employed. The material was placed in the crucible and rapidly melted under a protective atmosphere of helium gas by striking the arc on a tungsten stud and directing it upon the charge material. Details of operation, including drawings of this type furnace, have been published.'

Jan 1, 1955

By L. S. Darken

A quadratic formalism is developed lor the representation of the excess free energy, and of the activity coefficients of each component of a ternary system in the vicinity of a single component selected as solvent. This formalism, in contrast to the e formalism, is thermodynamically consistent at .finite concentrations. Numerous specific systems are used as illustrations, with cross checks where possible; these systems are Fe-C-X systems in the vicinity of 1600°C and include practically all those for which reliable data are available. It is shown that this formalism is usually quite adequate to rebresent available data up to a solute concentration of 20 to 30 at. pet. It is hoped that the formalism here presented may prove useful for the treatment and tabulation of data on ternary and multi-component solutions. SINCE, as discussed in a prior paper,' we do not as yet have an adequate basic understanding of the nature of binary metallic solutions, we cannot hope to be in better position for ternary and multicomponent systems. However, the accumulation of thermodynamic data on ternary and multicomponent metallic solutions has led to an urgent need for a rational formalism for the presentation and use of such data. Notable attempts to represent the isothermal isobaric thermodynamics of ternary solutions were made by Benedict et 01.' and by Wohl.3 These attempts were directed toward developing an analytic expression adequate to encompass the entire ternary triangle, primarily for organic systems; they generally involve the power-series approach, which has been shown' to be inappropriate, in general, even for binary metallic systems. On the other hand, interest in the thermodynamics of ternary and multicomponent metallic solutions has tended to focus either on general thermodynamic relations4-10 over wide compositional ranges, or on cases where one or more components have been at rather low concentration. This latter approach has been followed by Wagner,= by chipman,11 and by Alcock and Richardson,12 and more recently in many publications by the same and other authors. It has already been shown' that the thermodynamic behavior of binary metallic systems is, in general, relatively simple only in the terminal regions. Hence, it would appear that any approach, at this time, to a simple formalism for ternary and multicomponent systems must, a fortiori, be limited to the vicinity of the major component or solvent. The present treatment is aimed to be useful for a given solvent with moderate solute concentrations ranging up to 20 or 25 at. pet and in exceptional cases to considerably higher concentrations. In order to achieve even this modest objective, it is necessary that any appropriate formalism have built into it 1) a thermodynamic consistency (at least within the desired degree of approximation), and 2) an approach at infinite dilution to Raoult's law for the solvent and to Henry's law for each solute. Let us first formulate the condition of thermodynamic consistency for a ternary system. Under isothermal isobaric conditions, we may write for the molal value G of any extensive function dG - C1 dN1 + G2 dN2 + G3 dN3 [l] where the G's are the corresponding partial molal quantities and the N's are the atom fractions. Taking component 1 as the solvent, this relation may be rewritten in terms of the independent variables N2 and N3

Jan 1, 1968