Search Documents

By C. O. Lee, Z. W. Bartlett, R. H. Feierabend

DESPITE the fact that American brimstone production has increased 2 ½ times since the prewar period 1935-1939, the demand for sulphur exceeds the supply. To alleviate this situation efforts are being made to increase the production of sulphur and bring the shortage to an end. The most important developments are being undertaken on the Gulf Coast. One new brimstone mine has been put into operation and three others are being developed. These projects are expected to account for a large part of the additional sulphur production now anticipated for the free world.1,2 Except for a small amount of byproduct sulphur from sour natural gas and refinery gases, American brimstone is produced by the same process devised by Frasch 60 years ago, consisting essentially of the injection of superheated water at about 325°F into sulphur-bearing formations through wells which are drilled from the surface by standard oilfield methods. Sulphur deposits vary in depth from a few hundred feet to 2500 ft from the surface; in a typical deposit the sulphur occurs as crystalline aggregates in porous limestone and gypsum in concentrations varying from 5 to 40 pct, the thickness of the formation ranging from a few feet to several hundred.3 The deposits are usually surrounded by formations impermeable to the flow of hot water, the top and sides being enclosed by impermeable sediments and the bottom by dense impermeable anhydrite. As the hot water leaves the well bore, it percolates through the formation and transmits its heat to the rock and sulphur. When the sulphur reaches 240°F it melts, separates from the rock, and flows through the hot channels downward to the bottom of the well. Here it is freed from incoming water and from formation water, which saturates the porous rock, by gravity separation, liquid sulphur being 1.8 times as heavy as water. It then is pumped to the surface in a relatively pure state, 99.5 pct or better. Chief contaminants are organic impurities, such as petroleum residues, which are soluble in sulphur and tend to discolor it.4 Sixteen deposits of commercial magnitude have been discovered in the Gulf Coast area. Five of these deposits have been depleted and abandoned with production totalling more than 26,886,000 tons. Eight properties are operating and have produced 65,875,000 tons to Jan. 1, 1952, for a total Frasch-type production of 92,761,000 tons. Three new deposits are under development. Aforementioned deposits are listed in Table I. Each of these deposits has been found in the caprock overlying shallow intrusive salt plugs or domes and buried in several hundred to as much as 2500 ft of sediments. All salt domes do not contain sulphur; only 16 sulphur deposits have been found in a total of 231 salt domes which are known to exist in the Gulf Coastal states of Texas, Louisiana, Mississippi, and Alabama. Ten of the salt domes lie in the Gulf of Mexico offshore from the Texas and Louisiana coasts. Additional offshore domes may be found, but their value as a sulphur potential is questionable owing to the great hazard and high cost that can be visualized at these exposed locations where depths of water reach 50 ft. Marsh operations of Freeport Sulphur Co. are in the southeast section of Louisiana. In general, the country is low, flat, relatively uninhabited marshland broken by many shallow lakes and bayous which extend for irregular distances inland. Geologically, the coastal area is of sedimentary origin, having been built up gradually under the sea by deposition of material carried down by large streams to their deltas. Offshore bars were formed enclosing

Jan 1, 1952

By C. W. Hoffman, W. R. Hinken

Probability sizing, a fairly recent development in the field of particle separation, is now under investigation to determine its value to the mining industry. The method employed is probability sizing through a vibrating network of decreasing screen openings. While probability sizing is not new, the possibility of using it for coarse, highly abrasive ores at high tonnage rates has only recently appeared to merit practical consideration. The advantages of probability sizing vs. conventional screening methods are: (1) reduced space requirements for a high capacity unit, (2) fewer moving parts, (3) more versatile product sizing selection, (4) reduced maintenance requirements, and (5) lower power consumption. Screening is a necessary part of virtually every crushing circuit. At some stage in the process, particle separation becomes a controlling factor in the operation. The basic type of screen in use today is the vibrating unit, which usually employs a mechanical vibrator of one type or another to obtain sizing and material transportation across the screen surface. The vibrating screen has its limitations and inherent problems. Operators must live with: (1) high maintenance — worn rods, screen cloth, spacers, cross members, chutes, etc., (2) low capacity in relation to floor space requirements, (3) extreme noise levels, (4) high power consumption, and (5) structural problems in the screens and supporting steelwork. All plant operators have become tolerant of these drawbacks through the years, and little innovation has been developed in screening. The vibrating screens in use today incorporate improved metals, more efficient power sources, better lubricants, and increased manufacturing skill, but the basic machine itself remains unchanged. Screening is a relatively small part of most plants' operating expenditures and gets relatively little attention from research and development. The HiProb sizer is a new approach to the problem of particle separation on a high tonnage basis. Developed by Dr. Fredrik Mogensen (president of Fred-rik Mogensen, A. B. of Djursholn, Sweden), this unit has found its primary acceptance in the sizing of wet or dry materials in the fine ranges. Climax has been working cooperatively with Mine and Smelter Supply Company, the United States licensee, on the adaptation of the sizer to obtain consistent recovery at a high tonnage rate on a — 3/8-in. separation. This was a new application for the sizer and opened up a whole new field of problems. Dr. Mogensen's machine utilizes the control of normal probability of falling particles and is designed to eliminate some of the undesirable features of vibrating screens mentioned earlier. The machine is light, compact, consumes less power than conventional screens and has a low noise level. PRINCIPLES Probability sizing is a process designed to allow solid particles to segregate with a high ratio of the materials reporting into their respective size fractions with a minimum amount of misplaced particles. Sizing is defined in this paper as segregation of dry solid particles into fractions of comparable sizes. Probability is usually estimated as the ratio of the number of ways an event might occur vs. the total number of allowable ways. The probability process described depends upon the fact that particles falling through a network will segregate across the sizing surface even though all openings are larger than the particles. The degree of segregation is dependent upon the particle size and the trajectory applied by the sizing network to each falling particle. Specifically, the process utilizes a maze made up of screen cloth to control the path of a particle in free fall as illustrated in Fig. 1. The usefulness of this probability sizing process is dependent upon the degree of efficiency of an effective maze. Primarily, a maze must be extremely flexible to meet the multi-faceted nature of solid particles and, at the same time, the degree of control must be reproducible so that a desired separation is predictable. Dr. Fredrik Mogensen has formulated a maze that is not only flexible and easily controlled, but, mote importantly, easily adaptable to a working machine.

Jan 1, 1970

By H. J. McQueen, G. C. Kuczynski

ThE useful properties of k6-Alfenol and the thermenol alloys (summarized by J. E. Nachman and W. J. Buehler') have encouraged research into those alloys which, having compositions near 25 at. pct Al, 75 at. pct Fe, undergo an ordering transformation between 500° and 550°C. The equilibrium diagram of the iron-rich iron-aluminum alloys was first determined by Bradley and Jay.2,3 They distinguished three structures: the disordered, which is bcc; FeAl, which is simple cubic with one Fe atom and one Al atom per lattice site; and Fe3Al, which is fcc with three Fe atoms and one Al atom per lattice site. This last structure may be conceived as eight body-centered cubes with Al atoms at the centers of alternate ones, so that Al atoms have only Fe as first and second nearest neighbors. Later, Osawa and Murata4 determined the boundaries of the different superlattice regions in the iron-rich Fe-Al solid solution by dilatometric and X-ray methods. Two of the six phases, which they found between 0 and 50 at. pct Al, were never identified by other workers. A. Taylor and R. M. ones,' concurrently with and independently of this research, redetermined this diagram by measuring lattice parameters at temperature. Further reference will be made to their results. EQUILIBRIUM DIAGRAM A) Experimental Procedure—The alloys were prepared from NRC gas-free iron (99.9 pct Fe) and 99.99 pct Al. They were melted in alumina' crucubles under vacuum in an induction furnace. If the ingots were unsound or showed more than a 3 pct weight loss, they were rejected. The ingots were homogenized at 1100°C for 24 hr before hot-rolling at 700" to 900°C from 1 in. to 0.25 in. thick. It is interesting to note that alloys containing more than 28 at. pct Al were able to take an 80 pct reduction of area in the ordered FeAl region. The dilatometer specimens and specimens for chemical analysis were cut from these plates. A Leitz dilatometer was used to measure the coefficient of linear expansion as a function of temperature. The specimens were slowly cooled from 900" to 300°C where they were annealed for 10 hr before slowly cooling to room temperature. The expansion was recorded photographically as the alloys were heated and cooled at 1.5oC per min between 100" and 1000°C. The magnetic measurements determining the Curie points were performed on the dilatometer specimens in the dilatometer, by using direct current in the furnace windings both to heat the specimen at 1.5°C per min and to serve as the primary coil. The regular specimen holder was replaced by a thin alundum tube on which was wound, as a secondary, a closely spaced coil of fine copper wire. A reversal of current in the furnace windings produced, in the secondary, an emf which was proportional to the induction in the specimen, and which could be detected on a galvanometer. In this way, it was possible to determine the Curie points of alloys to within * 5°C. B) Results and Discussion—The coefficients of linear expansion, as obtained from the dilatometer curves, are plotted as a function of temperature and composition in Fig. 1. Since in many cases the heating and cooling curves were superimposed, it was decided to measure slopes of heating curves only. Definite high peaks, due to the transformations, were observed on each curve between 400" and 520°C, and, for alloys containing more than 23 at. pct Al, a second set of smaller peaks at temperatures above 660°C. The sharpness of the peaks indicates that ordering to Fe3Al is a first-order reaction. The compositions and the temperatures of these peaks are listed in Table I. When these temperatures are plotted as a function of the composition, the result is the constitution diagram presented in

Jan 1, 1960

By J. Groyecki, M. Markuszewicz, J. Lassota, A. Zawada

The ratio of stable to unstable inclusions was found to ploy an essential role in the process of sccorldar-y recrystatlizalion in Si-Fe. The analysis of the free energy of inclusions in the range of heat-treatment of individual inclusions to be predicted. The effects MnS. ns inslable inclusions. were investigated. TO secure a high induction, the secondary recryslulliztt-lion associated wilh the texture is necessary. To obtain a low core loss an additional refiuing in the solid state is required. It has been found that sulfur can be more easily removed in racunm than in hydrogen and thai this process was hindered by the prescrzce of INCLUSIONS play an essential role in the development of cube-on-edge texture in Si-Fe. Their function consists in restraining the growth of primary grains up to about 900°C and in passing subsequently into solution at higher temperatures. This process is accompanied by the selective growth of secondary grains with (110)[001] orientation. The general effect of inclusions depends on such factors as the type of impurities, their amount. dispersion and stability, the conditions of diffusion in the space of lattice of metal, and the reactions at the metal/gas interface. In recent years, some of these factors were the subject of a special investigation. A positive influence of Mns, siN,' and vN3 has been established. The quantity of impurities4 and their dispersion5 have been found to be of major importance. Attention was called to the vital importance of diffusion and the conditions under which the impurities are removed from metal., It has also been demonstrated that in Fe-Si alloys by the techniques of powder metallurgy a special opportunity exists to obtain the (110)[001] type texture. 6 The aim of this work was to conduct qualitative investigations on the influence of inclusion stability on the development of cube-on-edge texture in a metal containing approximately 3 pct Si. Experiments were carried out on cast alloys and on those manufactured by powder-metallurgy techniques. The results obtained from these experiments were utilized to explain the phenomena involved and to analyze the relationships between stable and unstable inclusions and the magnetic properties of alloys. EXPERIMENTS AND RESULTS The raw materials used in these experiments were the powder of carbonyl iron with the analysis (in pct) 0.044 C, 0.01 Mn, 0.005 Si, 0.009 P, 0.002 S, traces of Cu, 0.06 Ni, 0.0015 Al, 0.03 Cr, 0.02 Mo, 0.01 Ti, 0.002 Co, traces of Pb, and the powder of silicon containing 94.14 Si, 0.003 S, 0.048 C. The powders were ground and mechanically mixed in 100-g batches. and then pressed at 9 tons per sq cm into 74 by 24 by 8 mm blocks. Sintering was carried out at 1100°C for 12 hr in vacuum (2 x lo-' Tr) or in hydrogen. In this instance the material was heated slowly and subjected to prolonged soaking at 350°, 650°, and 750 2C, respectively, to secure reduction of ferro-oxides. This was checked by making measurements of the dew point, which was found to change from -15" to -35°C after reduction. The compacts after sintering were hot-rolled to 2.4 mm, annealed at 800 C, and finally cold-reduced to 0.35 mm with intermediate annealing at 800°C at a gage of about 0.8 mm. Impurities were added in the powdered form and mixed with iron and silicon powders. Sulfur in the elemental state, electrolytic manganese, and pure aluminum oxide were employed. Besides, to obtain a material with low contents of impurities, especially

Jan 1, 1967

By R. Lagneborg, R. Gullberg

An X-ray method for determinig volume fractions of phases in textured materials has been developed. The method involves measurements of the integrated intensities of reflections of each phase for one single orientation of the sample. The method was checked by evaluating the phase contents in samples from two stainless Cr-Ni steels containing austenite and ferrite in known amounts. In the present case measurements of about five reflections from each phase were required. The agreement between calculated and known volume fractions was found to be very close. AN X-ray diffraction method is often employed for determining the amounts of two or more phases in a material. The details of the method have been described at several instances.'" In short, the method is based upon the fact that the integrated intensity of a reflection is directly proportional to the volume fraction of the phase considered. In principle, the method only requires the measurement of the intensity of one reflection for each phase. The most severe shortcoming with this method is that it disregards influences from preferred orientation in the material. In a diffractometer, where this type of analysis is most conveniently carried out, the geometry is such that the diffracting planes for a specific Bragg peak are all parallel to the surface of the specimen. This implies that it must be required that the occurrence of the diffracting planes parallel to the specimen surface must be as frequent as for any arbitrarily oriented physical plane of the sample. This requirement will generally only be fulfilled for a material free of texture. Since all materials in reality always exhibit a preferred orientation to some extent. the deficiency of the method is quite serious. In cold-deformed material the texture is appreciable, but also annealed material will in many cases display a considerable texture. The problem of quantitative phase analysis in textured material is one of obtaining the integrated intensity averaged over all orientations of the specimen with respect to the X-ray beam. Lopata and ~ula~ have shown that this can be accomplished by integration of intensities over the whole pole figure, or by random rotation of the specimen in the X-ray beam, or by a combination of both. Hence, in this method the average integrated intensity for a specific reflection is obtained by directly determining the intensity for a sufficient number of physical orientations of the sample. However, since an excess of diffracting planes in a certain surface plane necessarily must be accompanied by a deficiency of another type of diffracting plane, it appears to be possible to obtain the correct average intensity for a specific diffracting plane by performing an appropriate averaging of intensities belonging to a large number of diffraction planes of different hkl when all intensities have been produced from one single orientation of the specimen surface. In the present work such a method has been attempted and tested experimentally for two stainless Cr-Ni steels containing austenite and ferrite. 1) THEORY The expression for the integrated intensity of a Bragg reflection diffracted from a phase in a polycrys-talline sample in a diffractometer is: where C is a constant only dependent on the incident X-ray power and the diffractometer geometry, v the volume of the unit cell, F the structure factor, m multiplicity of the diffracting plane, L Lorentz factor, P polarization factor, e-2 temperature factor, p average linear absorption coefficient of the irradiated vO1umej and V volume fraction of the phase 'Onsidered. Hence, the factor R in the abbreviated form of Eq. [I] can be calculated and depends only on 0 and the diffracting plane {hkl}. For an alloy containing two phases, a and y, we can write

Jan 1, 1967

By W. S. Hyler, W. L. Bruckart

The powder metallurgy and arc-cast types of wrought molybdenum stock were studied in rotating beam fatigue. Endurance ratios of unnotched specimens after 5x10 cycles were found to be 0.74 and 0.81, respectively. Fatigue notch factors (K,) of 1.36 and 2.05, respectively, were obtained on V-notched specimens having a theoretical stress-concentration factor Kt = 3.1. MOLYBDENUM and its alloys are rapidly gaining importance as engineering materials of construction for high temperature applications. AS a wrought material, molybdenum and its alloys are outstanding above 1800°F. It is necessary, however, with molybdenum to provide elevated temperature oxidation protection. This is currently being studied by a number of investigators. Thus far, there have been no published data on the fatigue behavior of molybdenum either at room temperature or at elevated temperature. The knowledge of fatigue behavior, particularly notched fatigue behavior, becomes increasingly important as the engineering importance of a material increases, especially from the design standpoint. The work described here was directed toward determination of the notched and unnotched rotating beam fatigue characteristics of molybdenum at room temperature. Also, it was desired to learn whether any difference exists between wrought molybdenum of the powder metallurgy and the are-cast types. Fabrication History of Bar Stock For this work, bar stock was procured from Climax Molybdenum Co. (are-cast type) and from Westing-house Electric Corp. (powder metallurgy type). The processing histories of these materials are listed in Table I. The first lot of are-cast molybdenum was deoxidized by aluminum additions. The second lot was deoxidized by carbon." Both lots of the powder Microstructure A microscopic examination of these materials, as received, revealed the powder metallurgy molybdenum to be free of inclusions and to be finely fibered. On the other hand, the are-cast C molybdenum possessed numerous carbide inclusions, and the arc-cast A appeared to have coarse grained fibers. These are shown in Fig. 1. Owing to the large apparent difference in fineness of fiber between the are-cast A and the powder product and are-cast C, a check was made of the recrystallized grain sizes to determine whether these differences persisted. A series of recrystallization anneals revealed mixed grain sizes in both the are-cast A and the powder product. Variations in grain diameter of as much as 50 times were found after full recrystallization at 1200°C for 30 min. There was no distinction between the two. Arc-cast C was not checked. Room Temperature Mechanical Properties Prior to subjecting the materials to fatigue tests, room temperature mechanical properties were determined. These data, together with the tensil: strength of the notched bars, data,togetherare listed in Table tensil: There were no significant differences in the tensile strengths of the two types of molybdenum. However, the powder metallurgy material was generally more ductile and yielded at a somewhat lower stress than the arc-cast material. Tensile strengths of the notched specimens indicated a slightly greater notch strengthening effect in the are-cast C than in the powder product, lot 2. Room Temperature Fatigue Properties Sample Preparation: Specimens were prepared for use in R. R. Moore rotating beam fatigue machines. These specimens had a continuous radius test section with a minimum diameter of 0.260 in. The specimens were prepared by grinding to shape and polishing to produce a smooth unworked surface. Polishing consisted of rotating a disk in the continuous radius section on which were attached, successively, emery belts of 240, 400, and 600 grit. The specimens were slowly rotated during the operation. The belt speed was high, and rotation was such that polishing scratches were longitudinal. Unnotched Fatigue Properties: Unnotched fatigue data were obtained from a number of specimens of each of the four lots of molybdenum. The results of the tests are presented in Fig. 2. From this figure,

Jan 1, 1956

By J. J. Gilman

Zinc monocrystals, when compressed nearly parallel to their basal planes (within 20), deform in a new way; and certain deformation markings, called "-bands," are typical of this new mode. Characteristics of these bands are described. Mechanical behavior of low angle zinc monocrystals was investigated in some detail. Recrystallization did not occur upon annealing of banded specimens that were free of deformation twins. -Bands do not seem to be the result of nonbasal slip, but rather, a result of a microbuckling mechanism. u-Bands differ qualitatively and quantitatively from ortho kink bands. A dislocation model, consistent with some of the features of u-bands, is described. THE plastic deformation of zinc monocrystals with slip planes (0001) nearly parallel to the stress axis was studied in this investigation. In a previous investigation, it was shown that some low angle zinc crystals (those with slip planes making angles of more than about 2.5+1° with the compression axis), deform by ortho kinking while others (those with slip planes making angles of less than 2.5+1° with the compression axis) deform in a new way.' This new mode of deformation will be described in some detail here. Some of its striking features are: 1—it operates only for compressive stresses, 2—its temperature dependence is anomalous, and 3—it exhibits a new type of "yield-point" behavior. The mode of deformation to be discussed is not new in the sense that no previous evidence of its existence had been reported. The markings that it creates on the cleavage surfaces of zinc crystals have been described by several investigators.'" However, this is the first time that it has been made to operate under controlled conditions so that its response to mechanical variables, temperature, and aging treatments could be investigated and its geometry completely described. Apparently. Jillson' as well as Holden3 and Pratt" believed that the small bands they observed were simply small versions of ortho kink bands. In fact, two of these authors3,6 "alled the markings "micro kink bands." In spite of the precedence, it is felt that this term is not entirely suitable because these bands do not have the same genesis as kink bands, and they are qualitatively different in structure. As will be indicated by later discussion, the bands seem to be related to the tensile deformation bands observed in aluminum. The present author has chosen to call the bands "micro deformation bands," or simply ",ubands," and the deformation process, ''p-banding." Experimental Methods Crystals were grown from 99.999+ pct Zn obtained from the New Jersey Zinc Co. The details of the technique are given elsewhere." It should suffice to say that the crystals were seeded for orientation control, and precision pyrex tubes were used for molding them. About 40 crystals were used, yielding some 130 specimens. Fig. 1 illustrates the typical form of the specimens and shows how the orientation angles are defined. The crystal specimens were usually 1 3/4 in. long and about 150 mil in diameter. The angle between the slip or cleavage plane (0001) and the specimen axis is designated by xo, while a is the angle between the maximum slope of the (0001) plane and the nearest close-packed direction [1210], vary ing from 0°to 30°. The crystals were cut into specimens with a jeweler's saw and the ends were squared by filing (specimens held in V-block). Crystals of this orientation are stiff toward bending, so this procedure introduced only deformation localized at the ends. Then the specimens were polished either chemically in 50 pct HNO³ or electrolytically in 20 pct chromic acid. The mechanical tests were made with an Instron testing machine. This machine weighs by means of electric strain gages on elastic bars and is quite stiff, since the full-load deflection of its load cells is at most 0.002 in. Most of the testing was done at a

Jan 1, 1956

By D. R. Wieland, H. T. Kennedy

The object of the work reported here was to determine the content of elemental sulfur in gaseous methane, carbon dioxide, hydrogen sulfide, and in mixtures of these gases, at pressures and temperatwes encountered in natural gas reservoirs. Sulfur content at equilibrium is reported for pure methane, carbon dioxide, hydrogen sulfide, and on three binary mixtures of each of the three pairs of gases at pressures of 1,000, 2,000, 3,000, 4,000, 5,000 and 6,000 psia and at temperatures of 150°, 200° and 250°F. In addition, the sulfur content of three ternary mixtures at the same temperatures and pressures are reported. The results indicate that the sulfur content is higher in the gases at higher temperatures and pressures. The content is highest in hydrogen sulfide, intermediate in carbon dioxide and lowest in methane. INTRODUCTION At ordinary pressures and temperatures, the concentration of a nonvolatile material, such as sulfur in a gas at equilibrium, is a function of the vapor pressure of the material and is independent of the nature of the gas. As the pressure and temperature increase, the gas assumes some of the properties of liquids, including the power to dissolve other liquids and solids, to an extent dependent on the nature of both the gas and the material dissolved. At equilibrium, the content of sulfur in the several gases considered here may thus be considered as solubilities which are fixed for a given composition of gas, temperature and pressure. The study of the solubility of elemental sulfur in gases is of interest because sulfur is sometimes present in reservoirs producing natural gas and must be present in the vapor phase. Upon reduction of pressure and temperature, the sulfur precipitates from solution in the reservoir and in the tubing and fittings. Due to the fact that the greatest pressure drop in the reservoir is around the wellbore, the volume of sulfur precipitated will be greatest in this locality and can cause a substantial reduction in the permeability of the formation in this area. As the natural gas flows up the tubing string, the pressure and temperature are further decreased, causing further sulfur precipitation. If the volume of free sulfur is large and remedial measures are not taken, complete plugging of the tubing can occur. Knowledge of the content of sulfur as a function of composition, temperature and pressure will enable the operator to determine what changes in pressure and/or temperature are necessary to keep the sulfur in solution. If the sulfur solubility is large and can be controlled, the operator may desire to produce the well at a high wellhead pressure and temperature and reclaim the sulfur at the surface. The high solubility of sulfur in hydrogen sulfide (5.6 per cent by weight at 5,000 psi and 200°F) suggests the feasibility of recovering sulfur by injecting this gas into sulfur-bearing reservoirs and expanding the produced gas to precipitate out the sulfur. The present project was designed to measure the solubility of sulfur in carbon dioxide, methane, hydrogen sulfide and mixtures of these three gases at various temperatures and pressures. These gases were the major constituents of the gas well where plugging by sulfur was encountered. A study of the published literature shows no data on the solubility of sulfur in any gas, although Hannay and Hogarth,' in 1880 reported that it was soluble in carbon disdlide above the critical temperature of carbon disulfide. EQUIPMENT AND PROCEDURE Fig. 1 shows the layout of equipment employed to bring gases to equilibrium with sulfur and to isolate the quantity of sulfur contained in a known volume of gas. Pure gases were measured in the charging bomb at known temperatures and pressures and displaced into the reservoir bomb to make up the desired mixtures. When equilibrium was achieved

By F. P. Bobrowski, G. B. Spencer, Alton B. Cook

In estimating production gas/oil ratios and oil recoveries from reservoirs containing highly volatile oils it is highly important to include condensate that may be recovered from the gas produced from the reservoir. The volume of the hydrocarbon liquid condensed from the production of the solution gas that has been liberated. in some reservoirs may equal or even exceed the volume of recoverable stock-tank oil as estimated by present methods. The usual procedure1, 2, 3 in estimating future reservoir performance includes use of relative permeability data of the reservoir rock to gas and oil and includes material-balance calculations utilizing data on the volume of the reservoir fluids, oil and gas production and reservoir pressure decline, and data on the physical properties of the initial reservoir fluids. The inaccuracy in the procedure results from the false assumption that all of the free or liberated gas that enters the well bore of reservoirs containing highly volatile oils remains in the gaseous phase as it is produced. This paper presents a method for estimating future reservoir performance and oil recoveries based on special labora. tory analyses of reservoir-oil samples and recognition of the additional volume of hydrocarbon liquid that will be recovered at various stages of depletion from a solution.gas.drive reservoir. The method also includes calculations of the volume and composition of the hydrocarbon liquids that can be recovered by processing the produced gas in a natural-gasoline plant. The development of the method resulted from a study of laboratory analyses of reservoir samples and of field data obtained from two reservoirs containing oil of the highly velatile type. Relatively high pressures and temperatures prevail in oil reservoirs discovered at the greater depths of present-day drilling. The contained fluids may have high saturation -Dressures and large volumes of gas in solution. The oils and gases under these conditions may be almost identical in compositions and densities.4,5 Also, engineers have noted that, for a number of oil reservoirs and especially the deeper reservoirs, the API gravity of the stock-tank oil increaees as the production gas/oil ratios increase. They attributed this increase in API gravity of the stock-tank oil to the formation of condensate as the liberated gas in the reservoir is being produced. SOURCE OF DATA FOR CALCULATIONS Subsurface oil samples and well-test data were obtained from the E. Constantin-Lambert Well No. 1 in the Elk City Field, Okla., to demonstrate the need for and a method of calculating future reservoir performance when consideration is given to the recoverable hydrocarbon liquid from the production of solution gas that has been or will be liberated in a reservoir. The Lambert well is located in C, SW 1/4, SW 1/4, Set- 18, T-l0-N, R-20-W, Washita County, Okla. At the time of completion it was on the east edge of the development and Was producing from conglomerate through 30 perforations in the 5 1/2-in. casing at a depth of 9,859 to 9,864 ft. The well Was completed on July 9, 1949, and subsurface oil samples were obtained July 29 and August 1, 1949. Production gas/oil ratio data were obtained during the operation in series of two Separators at high and low-pressures of 314 and 44 psia, respectively, and at an average temperature of approximately 60°F. The flowing bottom-hole pressure at the time of sampling was 3,934 psis. The static bottom-hole pressure was not obtained at the time of sampling, as the well could not be shut in long enough for testing because gas produced from the well was used for fuel at an offset drilling well. However, the initial reservoir pressure was calculated to be 4,364 psia from knowledge of pressure gradients in other wells in the field and the depth of the casing perforations in the Lambert NO. 1 well.

Jan 1, 1951

By F. D. Rosi, C. H. Mathews

THE plastic properties of face-centered cubic metals below room temperature present a field of investigation which has not been extensively ex-plored. The work by Schmid and Boas1 has demonstrated the importance of temperature upon such properties as strain hardening and critical resolved shear stress. The work by Yamaguchi2 upon the shear stress as related to the number of slip bands accentuates the necessity for further experiments of a similar nature. The approach to a mechanical equation of state from the standpoint of thermal fluctuations and activation energies by Becker3 and more recently by Kauzmann4 further emphasizes the need for a quantitative and more comprehensive analysis of the dependence of fundamental plastic properties on temperature. The purpose of the present work was to investigate specifically: (1) The gross shape of the stress-strain curves at several temperatures, (2) the change in the critical shear stress as a function of temperature, and (3) the number and appearance of slip bands as a function of strain and temperature. Preparation of Specimens Single-crystal specimens of 99.996+ pct alumi-num, 1/2 in. in diam and 5 to 6 in. in length, were made by the Bridgman method of gradual solidification from the liquid state. The crystallographic orientation of the single crystals was determined from back-reflection, Laue X-ray photograms ac-cording to the method described by Greninger.6 In most specimens the Laue photograms showed double diffraction spots indicative of the lineage structure type of imperfection, discussed in great detail by Buerger.7 The angular spread of these spots was never observed to exceed 2". Most of the crystals were radiographed to insure against microporosity. In preparing the metal surface for optical microscopy, the following sequence of operations gave good results: The as-cast crystals were turned down in a lathe, 0.001 in. per cut, to obtain a 2.5 in. gauge length. The cold-worked layer resulting from this operation was removed chemically by etching with Tucker's reagent. Then the specimen was polished mechanically through 2/0 metallographic emery paper, after which it was etched again to remove the cold-worked layer resulting from the mechanical treatment. A 48-hr anneal at 580°C ±10°C followed so as to insure an essentially stress-free single crystal. After the annealing treatment, the specimen was electrolytically polished in a 2:l solution of methyl alcohol and concentrated nitric acid. With a current density of 10 amp per sq dm (decimeter) the time required to obtain a satisfactory surface varied from 10 to 12 min. The polish-ing was carried out for short periods of 2 min to avoid rapid deterioration of the solution as well as to enable the rotation of the specimen 180" for uniformity of polish. It was necessary to place the solution in a bath of dry ice in view of its explosive nature at room temperature. Etching of the electrolytically polished surface was accomplished by using the fuming etch-pit method recommended by Lacombe and Beaujard8 for high-purity aluminum. Method for Tensile Testing A modification of the loading equipment devised by Miller9 was used. In this apparatus, the specimen was suspended from a chain and gimbal arrangement (for axial loading) in a heavy steel framework connected at the bottom to a balanced 6:1 lever and bucket system. Loading of the specimen was accomplished by allowing sand to flow from a reservoir into the bucket suspended from the longer end of the lever-arm at a rate of approximately 3 lb per min. Strain measurements were made using the Baldwin SR-4, bonded, resistance-wire, strain gauge and an SR-4 portable strain indicator (type K), which permits a reading accuracy of 2 microinches per inch. For low-temperature study, the gauge was calibrated by measuring the elastic modulus of an annealed stainless steel rod, which is known to be independent of temperature."

Jan 1, 1951

By G. A. Mancini, V. Bharucha, J. W. Spretnak, G. W. Powell

The characteristics of the motion of the a interface during the "down" transformation was studied in zone-refined iron and dilute binary alloys containing nickel and molybdenum by means of the thermionic emission microscope and high speed photography. The frontal movements were found in all cases to be definitely discontinuous with time and an appreciable number of incremental jumps were found to proceed in the reverse direction (a to b). Molybdenum was found to be particularly effective in increasing the frequency of the increments of transformation from the stable to the metastable phase. A knowledge of the mechanism by which alloying elements affect the hardenability of a steel is desirable from both the practical and scientific viewpoints. It is well established that microstructures consisting of tempered martensite and lower bainite exhibit the best performance in terms of toughness and resistance to crack propagation. The presence of some upper transformation products, namely ferrite and pearlite, is in general undesirable. Various researches have indicated that the ferrite matrix grain structure is a very important difference between the upper and lower transformation products, namely equi-axed vs acicular. Any comprehensive theory of the decomposition of austenite should explain the dependency of the morphology of the matrix on undercooling. The contribution of various alloying elements to hardenability has been determined experimentally and catalogued in considerable detail. A rationalization of the basic mechanism or mechanisms by which individual elements affect the kinetics of the decomposition of austenite to products other than the phase "martensite" has not been evolved as yet. Interest in this problem was stimulated by the effects of minute quantities of boron in hardenable steels. This paper deals with one aspect of this problem, namely the characteristics of the ?-a transformation in high-purity iron and in two carbon-free iron binary alloys. A detailed historical account of the scientific developments in the study of the decomposition of austenite would be a prodigious undertaking and will not be attempted here. There are several excellent reviews in the literature on the formation of pearlite, martensitic reactions, and kinetics of solid-state reactions. The thinking on reaction mechanisms has been influenced to a large degree by the "classical" Tammann nucleation and growth model, in which an embryo springs into being by a fluctuation, and grows to a critical size through atom by atom deposition. Such a process is expected, accordingly, to be diffusion controlled. Considerable research attempting to relate the contribution of alloying elements to hardenability on the basis of their effect on the diffusivity of carbon in iron has not been productive from a mechanistic viewpoint. The formation of pearlite and ferrite has been treated in terms of nucleation and growth processes in which presumably the lattice transformation also occurs by a diffusion process. The other prominently considered mechanism is the "martensitic" or cooperative shearing mechanism. It seems generally, but not entirely, agreed that the phase "martensite" forms by this mechanism, and that it is involved to some extent in

Jan 1, 1962

By Castle. J. E., J. L. Gillson

In this chapter there is a wide difference in the meaning of some words used for rock and mineral names as defined by scientists and tabulated in the "Glossary of Geology and Related Sciences," published in 1957 by the American Geological Institute, and the meaning as used by the commercial producers of feldspar. It is necessary, therefore, to define these terms giving both the "scientific" and the "practical" definitions. There is no ambiguity about the name feldspar itself. This is a general term for a group of related minerals which are silicates of aluminum, combined with sodium, potassium and calcium. The feldspars are the most abundant minerals of the igneous rocks, and since these rocks make up the largest proportion of the earth's crust by volume (although not of the actual surface area of the continental land masses) the feldspars are the most abundant minerals of all. The igneous rocks themselves are classified on the basis of the variety of the feldspar present. The potash feldspars, which are called orthoclase and microcline, are the dominant minerals of the granites and syenites, and of their fine grained equivalents, the rhyolites and trachites. The plagioclase feldspars form an isomorphic series, of which the sodic endmember is called albite, and the lime endmember, anorthite. The members near the sodic end, albite, oligoclase and andesine are the characteristic feldspars of the granodiorites and diorites, and of their fine grained equivalents, the dacites, and andesites. These feldspars-orthoclase, microcline, albite oligoclase and andesine-are the feldspars used commercially. Labradorite, a member of the plagioclase group, in which the lime exceeds the soda in the chemical composition, is the common feldspar of the gabbros, anorthosites, norites, basalts and other so-called "basic" rocks. Although some attempts have been made to use labradorite as a commercial feldspar, none is now used except as an ornamental stone. The mineral anorthite is very rare. Since the feldspar in most of the common igneous rocks is relatively fine grained, and mixed intimately with other minerals, from which it can be separated cleanly only with difficulty, most masses of the common rocks cannot be used as sources for the feldspar contained in them. It is only the rarer types of rocks in which the feldspar is very coarse-grained, or ones containing very little of the iron-bearing minerals which are objectionable impurities in commercial feldspar, that are quarried to yield an acceptable product. The most widespread type of such a rock from which commercial feldspar can be produced, is that called "pegmatite." These rocks are dikes and bodies of irregular shape and of a size measured in feet or yards in most cases, rather than in miles. They are more commonly associated with granites, rather than with other coarse-grained igneous rocks. Many of them contain crystals of various minerals, including the feldspars, that are much larger than are found in the host rock, the granite, and in many there are large masses of feldspar that are sufficiently free from iron-bearing silicates so that products acceptable to the ceramic industry can be produced, in some cases simply by hand sorting. Most of this feldspar in pegmatites, however, does contain intergrown quartz up to 25 pct. Pegmatites are so important, not only as commercial sources of feldspar, but also of other minerals which are produced com-

Jan 1, 1960

By T. Lux, H. -J. Krassnig, I. Filzwieser, E. Hecker, R. Degel, A. Filzwieser

Non-ferrous metals find their applications in smartphones, tablets and computers. These materials with their particular properties are the basis of our modern life. SMS group is well prepared for this huge market and for growing future challenges. A large contribution here is the new joint venture PolyMet Solutions that was founded by SMS group and Mettop, an Austrian engineering company, with the objective to develop new technical solutions for the primary copper production lines as well as for non-ferrous metals starting with the primary smelting of concentrate and ending with the electrolysis. PolyMet Solutions provides the process know-how whereas SMS group supplies the plants and equipment and Mettop the key components. SMS group and Mettop also cooperate in the field of tankhouse technology. Together with Montanwerke Brixlegg AG, Mettop has developed together with a parallel flow technology (METTOP-BRX Technology), allowing a current efficiency of above 98 % at a current density of 420 A/m², which is a milestone in copper electrolysis. For the secondary copper production route, SMS group and PolyMet Solutions developed an innovative refining furnace (PolyRefine) for the smelting and refining of copper scrap. The refined copper is directly charged to the Contirod line to produce copper rods and wires. The innovative cooling solutions of SMS and PolyMet Solutions come into play where furnaces have to stand the highest loads and stresses, for instance in areas of very high temperatures or temperature fluctuations, aggressive exhaust gases and slags, or at critical spots such as taphole areas. Custom-tailored cooling systems for furnace vessels make sure varying loads are compensated in a targeted and effective manner. The solutions include air cooling, spray cooling, cooling technologies with integrated copper elements such as CFM (Composite Furnace Modular) cooling systems, plate and finger coolers. The major innovation in the field of furnace cooling is the ILTEC (Ionic Liquid Cooling) Technology which paves the way for increased plant safety. This revolutionary, patented cooling technology is jointly marketed by Mettop and SMS group. It permits water-free cooling to be implemented and thus makes operation safe wherever it is applied. INTRODUCTION Non-ferrous metals or NF metals are changing the world. There is no modern industrial sector that can do without these valuable metals. Non-ferrous metals find their applications in smartphones, tablets and computers. These materials with their particular properties are the basis of our modern life. The importance of the non-ferrous metals market is reflected by two figures. In 2018, the production of non-ferrous metals was worth more than 237 billion Euros. This contrasts with 255 billion Euros of the value of iron and ferro- alloy production in the same year (International Organizing Comittee for the World Mining Congresses, 2018). Hence, the NF metal industry is almost as important as the iron and steel industry. SMS group is well prepared for this huge market and for growing future challenges. A large contribution here is the new joint venture PolyMet Solutions that was founded by SMS group and Mettop, an Austrian engineering company, with the objective to develop new technical solutions and to enhance customer value. The prices of nearly all metals have come under pressure during the past few years. Therefore, competitive technologies are regarded a crucial factor to achieve success in this critical market situation respectively to stabilize the market position.

Jan 1, 2019

By K. J. Brondyke, P. D. Hess

Two processes have been developed for improving the quality of molten-aluminum alloys before casting. The Filtration Process. which involves passing molten metal through a packed bed of granular filter material, is a rapid means of removing finely divided particles. It has the most potential in those instances where removal of inclusions is of primary importance. The Combination Fillration-Inert Gas Fluxing Process inuolzles introduction of an inert gas so that it will diffuse countercurrent to metal flow through the filter bed of granular material. Dissolved hydrogen is removed from the metal in addition to removal of finely divided particles. The Combination Process is most useful where both inclusion removal and attainment of conistently low-hydrogen-content metal are important. Metal treated by the Combination Process is of higher and more uniform quality than heretofore attainable with prolonged chlorine fluxing. Costs of the Combination Process can, for the most part, be offset by savings derived from high recoveries and increased production of superior-quality products. IMPROVEMENT in the quality of molten-aluminum alloys is secured generally through the use of some fluxing practice in a crucible, holding furnace, or ladle involving either gaseous or solid fluxing media. Typical fluxing agents may include the gases nitrogen, argon, or chlorine used either singly or as mixtures and the solids aluminum chloride or hexachloroethane. Regardless of the fluxing means used, the primary objectives are the adequate removal of both metallic and nonmetallic inclusions and reduction of hydrogen content to an acceptably low level. The ultimate goal is to produce ingots and cast products of high quality free from inclusions and porosity. The development of ultrasonics for measurement of internal quality, tightening of quality controls, and the application of the aluminum alloys to new or different commercial fields have been responsible for an ever increasing demand for improvement of quality of both cast and fabricated products. This demand for high quality has not been restricted to any single type of product. On the contrary, the demand encompasses about the entire variety of products including those for fabrication, those to be machined, buffed, or finished for decorative purposes, and those for critical applications where both surface and internal quality is of utmost importance. In many instances products acceptable in the 40's would now be scrapped as unacceptable by these higher present-day standards. With this ever increasing demand for higher quality, it became apparent at Alcoa that conventional means of melt treatment were inadequate in many instances and new approaches were necessary. Consequently the research program was intensified with attention focused on metal treatment during transfer in order to reduce the furnace processing time to a minimum in an effort to attain the desired results at a minimum of additional expense. As a result of this intensive research program which covered numerous variations and adaptations of conventional methods in addition to new methods of melt treatment, several new processes were developed, two of which will be described here. The first of these, a method of melt filtration, was patented in February, 1959.l The second process involving combination filtration—inert gas fluxing was patented in June, 1962. 2 Other melt-treatment processes developed during this period of investigation were patented as listed.3 FILTRATION PROCESS General Description. The Filtration Process, which involves passing molten metal through a packed bed of granular filter material, is a rapid method of effectively removing finely divided particles. It is an impingement-type filter; hence the size of the particles removed from the metal are considerably smaller than the interstices of the

Jan 1, 1964

By A. W. Ruff

In the last ten years large gains have been made in the field of blasting. These gains have been both in the theoretical and in the practical application of explosives. One of the most publicized changes in the practical application of commercial explosives is the now-prevalent use of ammonium nitrate and fuel oil. The new water-compatible mixture of ammonium nitrate and TNT should also have a large field of application. Most of the theoretical gains have been concerned with the actual rock breakage obtained with explosives. In the last ten years, large gains have been made in the field of blasting. These gains have been both in the theoretical and in the practical application of explosives. One of the most publicized changes in the practical application of commercial explosives is the now prevalent use of ammonium nitrate and fuel oil. The new water-compatible mixture of ammonium nitrate and TNT should also have a large field of application. Most of the theoretical gains have been concerned with the actual rock breakage obtained with explosives. EXPANDING-GAS-BUBBLE THEORY There has been an outstanding change in the conception of how an explosive produces rock failure. The early theory which explained rock breakage was correct for some of the first force-producing agents such as quicklime. When a drillhole was filled with quicklime and water added, the material expanded and steam was generated. The expanding material and the steam exerted a slowly increasing pressure on the sides of the drillhole. The force broke the rock by splitting. Because a great quantity of gas was produced by the deflagration of gunpowder, the same process of the gas pressure splitting the rock was assumed to take place. Even after 80 years of use, the rock-breaking action of all high explosives was thought to be caused entirely by the expanding gas bubble which tore and split the rock. Fig. 1 shows a vertical section through an exploding spherical charge of high explosive. It illustrates the early theory which attributed the entire breakage to the expanding gas bubble. The basic idea of this theory is that the breakage started at the explosive charge and progressed toward the free face. REFLECTED-WAVE THEORY me expanding-gas- bubble theory has gradually been replaced by the reflected-wave theory. The reflected-wave theory explains rock failure by explosives in the following manner: The enormously high gas pressure in the drillhole produces fracturing of the rock on the sides of the drillhole. The fracturing around a 1 1/2-in. diam drillhole is usually confined to an area with about a 6-in. diam. In the fractured area, the pressure of the gas is reduced until the force on the walls is no longer capable of fracturing the rock. Although the gas pressure does not continue to fracture the rock, the pressure imposes a high impact stress on the wall rock. In addition, a pressure or seismic pulse is produced in the rock. The pulse is probably entirely a compression pulse when originally produced in the rock. But, with distance, part of the energy of the compression pulse is transformed into a tension pulse which follows the compression pulse. The explosive charges and burdens used in conventional mine blasting are such that the tension pulse of the original wave is probably too small to be considered in a practical evaluation of the theory. The compression pulse is transmitted through the rock with no associated fracturing.

Jan 1, 1961

By B. H. Bergstram, C. L. Sollenberger

When glass spheres are crushed by slow compression loading, the outer lune-shaped fragments resulting from the fracture consistently fly outward at high velocity. About 45 pct of the strain energy fed into the sphere-platen system reappears in the form of the kinetic energy possessed by these fragments. These measurements were obtained from high-speed photographs. This kinetic energy can be utilized for addtional comminution if the fragments are allowed to impact against a suitable structure. Comminution theory has advanced considerably in recent years by the study of this unit operation under laboratory conditions. Some of the parameters have been isolated, but the experimental measurements of the pertinent quantities, such as energy, particle size, etc., are still only made prior to and after the conclusion of a fracture sequence. The catastrophic fracture process itself has not been adequately studied from a comminution point of view. It has recently been suggested by Gilvarry that the fragments which result from the free crushing of a single glass sphere by slow compression contain a considerable amount of kinetic energy after fracture. This kinetic energy, if properly directed, possibly can be partially utilized to cause additional fracture. In this paper a hypothesis will be presented which suggests that this kinetic energy is necessarily present and that its dissipation is the process by which a large part of the thermal energy imparted to the crushed product is generated. Evidence supporting the existence of kinetic energy and its utilization for secondary fracture will also be presented. THEORETICAL A previous paper4 has shown that the load-deformation curve of a system composed of an elastic sphere gripped by a pair of parallel platens, can be predicted by a consideration of the theories of Hertz as summarized by Timoshenko.' The deformation A, of one half of the system is given by which states that the deformation is a function of the mutually applied load, P, the radius of the sphere, R; and the respective physical properties of Poisson's ratio, v, and Young's modulus of elasticity, Y. The shape of experimental load-deformation curves conform to this relationship. The energy input to the sphere-platen system, can be predicted from the integral of the load acting through the appropriate distance, dA. Since dA can be evaluated in terms of P from the derivative of Eq. 1, this integral can be integrated between limits of 0 and P. The test sphere, however, is loaded at not one but at two points of contact, i.e., at both ends of a diameter, and hence the total energy input, E, is twice the energy input at each end, or The energy input to the system calculated from this equation corresponds to the energy computed from the measured area under the load-deformation curve. Timoshenko, considering the impact of two perfectly elastic spheres, has shown that the inter-penetration distance A is given by - m f (D (^ * ^t w as modified for the special case where one sphere is of infinite radius, i.e., its surface is a plane; where M is the mass of the finite sphere of radius R, and V is the velocity of approach at the start of an impact and also equals the final velocity of separation for perfectly elastic bodies. Because A is also a function of the load and the elastic properties, as shown in Eq. 1, the velocity, V, can also be calculated in terms of the elastic properties and maximum load, P, or

Jan 1, 1961

By I. Tamura, J. O. Brittain, T. Mura

Plain carbon steel in the cold worked or marten-sitic conditions has an internal friction peak at about 250 oC at a frequency of I cps. The influence of substitutional alloying elements on this peak was examined experimentally. The alloys were vacuum melted Co-, Cr-, Mo-, Ni-, and Si-iron (about 3 pct alloying elements), and carburized Si-iron. The internal friction of the alloys in the temperature range 30o to 500 OC was determined by means of a torsion pendulum. The 250 oC peak of the cold-worked alloys was lower in height than that observed in plain C-iron and steel. Carburized Si-iron in the quenched condition had a peak which occurred at a slightly lower temperature than in quenched plain C-steel, but the height of the peak was substantially greater than that found for the same alloy in the cold-worked condition. The activation energy of this peak for martensitic Si-steel was about 35 kcal per mol. ANNEALED a iron has two internal friction peaks due to nitrogen and carbon at 20o and 40o C respectively, at a frequency of 1 cps. If a iron is cold worked, these diffusion peaks become smaller and a new peak appears at about 250o C. The activation energy for the 250o C peak is in the range of 32 to 44 kcal per mol and has an average value of 38 kcal per mo1. It has been experimentally verified that both interstitial solute atoms and dislocations are necessary for the 250o C peak. 3 Wert has also shown that an incubation period precedes the appearance of the 250 C peak.4 With regard to quenched martensitic steel, Ke et al.596 observed two peaks at around 130o and 250o C. They conjectured that the 250o C peak in martensite was due to the same mechanism as the 250°C peak in cold worked a iron, and the 130°C peak was due to the nature of tempered martensite. They did not report the activation energy for these peaks. Chernikova7 found only one peak at about 200° C in tempered martensite. In a previous paperS we reported an activation energy of approximately 40 kcal per mol for the 250° C peak in plain carbon martensitic steels. Ichiyama8 found the activation energy to be about 36 kcal per mol for the 250° C internal friction peak in steels in the martensitic condition. The present authors proposed a theory for the 250°C peak for cold worked and quenched iron and steel.= The theory for the peak is based upon the addition of a strain-energy term to the free energy for the formation of a carbide precipitate due to the presence of a disclocation. The model employed for the relaxation process consists of the growth and solution of a carbide precipitate of critical size as a consequence of an oscillating dislocation. In this report, the influence of substitutional alloy ing elements on the 250° C peak is examined and the experimental results are discussed in terms of our theory for the peak. Most of the experimental work on the alloy steels was confined to the Fe-Si-C alloys.

Jan 1, 1962

By N. F. Schulz, H. A. Lex, J. D. Zetterstrom

A green ball of iron ore faces many perils from the time it is formed until it finally emerges from the pelletizing furnace as a hardened pellet. For instance, if the rate of heat transfer into a ball is sufficient to produce vapor from either the free or combined water more rapidly than it can escape at a tolerable pressure, the ball may split, spall, or even explode, a failure commonly known as decrepitation. To avoid such failures, one must either limit the rate of heat transfer during the drying and preheating stages, at the expense of production rates, or improve the decrepitation resistance of the green balls. The latter remedy may often be accomplished through changes in ore preparation, balling procedures, or the judicious use of binders or other additives. INTRODUCTION Pelletization has become established as an especially desirable method for the agglomeration of fine taconite concentrates and it promises to be equally satisfactory for improving the physical structures of certain natural ores. A high-quality pelletized iron ore consists of uniformly sized spheres, usually about 1/2-in. diam, which are strong enough to resist abrasion and breakage during handling and which reduce well without disintegration in the blast furnace. The unfired agglomerates, "green balls", are subject to several destructive effects that must be avoided or minimized if a high-quality product is to be obtained by pelletization. Among these are abrasion and impact deformation or breakage during handling of the wet green balls, deformation and breakage by compressive forces in the bed of ore in the pel-letizing furnace, decrepitation during drying and preheating, wind erosion, and radial cracking at firing temperatures. Moisture condensation from the warm saturated gases downstream from the drying zone on wet, cool balls may cause bed collapse if it becomes excessive. Decrepitation is defined as the sudden disintegration of green balls, usually with an audible pop, that occurs when they are heated too rapidly during the drying or preheating stages of the pelletization process. The extent of ball disintegration may vary from merely splitting off a small fragment to almost total disintegration into the original ore particles making up the ball. Such ball destruction results in a decreased yield of pellets, and the fragments, which also tend to interfere by obstructing the gas flow through the bed, must eventually be screened from the fired product and recycled. The closely related type of ball failure that sometimes occurs during the high temperature firing stage, resulting in radial cracks without fragmentation, was not considered to be decrepitation for the purpose of this investigation. Failure by decrepitation is not usually a serious problem in the pelletization of taconite concentrates. The problem is significant, however, in the pelletization of some natural ores, especially those containing hydrous iron oxides. In some instances, economicd production rates cannot be maintained if the drying and preheating rates are slowed down enough to avoid decrepitation. OBJECTIVES This investigation was undertaken to: (1) Develop a practical laboratory means for quantitatively measuring the tendency for green balls to decrepitate in iron ore pelletizing furnaces, and (2) Investigate the causes and cures of ball decrepitation. MATERIALS Two iron ores were used in the work reported here: a taconite concentrate at 90% minus 325 mesh, containing 65.0% Fe, 8.4% SiO2, and no loss-on-ignition; and a crude oxidized ore at 54% minus 325 mesh, containing 59.1% Fe, 3.6% SiO2, 1.1% A12O3, and 9.5% loss-on-ignition. For a special test of effect of particle size distribution on decrepitation, two other

Jan 1, 1967

By T. D. Murphy

The element silicon, with its usual partner, oxygen, plays the same role on this planet relative to inorganic materials as carbon and hydrogen play with respect to living organisms. The crystallographic structure of silicon dioxide (SiO,) consists of one atom of silicon well-nigh inseparably bonded to four contiguous atoms of oxygen, a gas of but slightly more than half its atomic weight, forming a three-dimensional network of SiO, tetrahedra (Dietz, 1968). This wispy arrangement is the fabric of the mineral quartz which is one of the harder, more abrasive, and chemically stable raw materials to be found in Mother Nature's cupboard. Most of us are vaguely familiar with the observation that nearly 60% of the lithosphere to an approximate depth of 10 miles is composed of these two elements, which proportion actually rises to about 75% if the atmosphere, hydrosphere, and biosphere are included (Parker, 1967). Elemental silicon is a brittle steel-gray metalloid with a density of 2.42 and does not occur in nature. In its limited commercial form, which is still brittle and metallic in appearance, its density drops to 2.33. It combines with oxygen to form the gaseous oxide SiO, or the solid dioxide SiO, (analogous to its congener carbon in CO and CO,); a tetrachloride SiCl, (analogous to CC1,); or, combining with oxygen and one or more metal ions, forms the largest rock-making family of all, the silicates. Further, next to the feldspars, quartz is the most abundant known mineral and, in some form or another, accounts for roughly 12% of surficial terrestrial rock. It is this so-called "free silica" to which your attention is chiefly directed in this chapter. In any such consideration of silica, its several crystalline phases with their attendant differing physical properties appear worthy of delineation. Alpha quartz is the only one of this interesting polymorphic family that is thermodynamically stable at normal pressures and temperatures up to about 573°C. The low phases of tridymite and cristobalite can exist in the so-called metastable state below 117°- 200°C but seldom occur in nature in these two different crystal forms (Sosman, 1965). Opaline silica, now considered by most researchers to be a variety of cristobalite, occurs in abundance and is the only exception. The three remaining polymorphs, keatite, coesite, and stishovite, also are metastable under ambient conditions. Keatite, however, is not known to occur naturally and has only been synthesized in the laboratory. The other two have been identified in submicron sizes and in microscopic amounts, occurring naturally as a result of high order shock-wave pressures generating quite elevated temperatures-such as might accompany the impact of a large meteorite on a hard sandstone terrain (Chao, et al., 1962). An intriguing characteristic of these silica minerals, and one which has very practical applications, is their extremely variable densities. The classic 2.65 specific gravity of alpha quartz drops to 2.20 in tridymite, cristobalite, and lechatelierite (natural silica glass), as well as in many man-made glasses of commerce which are merely noncrystalline or amorphous solids in the form of super-cooled liquids which can no longer change their shapes (Pauling, 1950). It rises again to 2.50 and 2.93 for keatite and coesite, respectively, and finally becomes a reported 4.35 for stishovite-nearly a 50% range in density for the known physical combinations that silica naturally assumes (Frondel, 1962; Konnert, et al., 1973; Pecora, 1960).

Jan 1, 1975

By Robert B. Hoy

If the reader finds that the basic information in a commodity chapter is insufficient, he can consult the appropriate sources in this chapter to find more detailed or more up-to-date information. In these days, technology develops so rapidly that this 5th edition will be somewhat out of date even by the time it is distributed. A comparison of this edition with the 4th edition (1975) of Industrial Minerals and Rocks will clearly demonstate how rapidly the scene changes. One of the best sources of new information, of course, is attendance at technical meetings. For example, the papers presented at the national and sectional meetings of AIME usually discuss new developments in the respective divisions of the society. Frequently this information is available in Preprints. In addition some are printed in Mining Engineering and/or the Transactions of the Society of Mining Engineers of AIME. Furthermore, other professional and trade journals contain articles pertinent to the field. A journal introduced in 1967, Industrial Minerals, published by the Metal Bulletin, Ltd., London, is an excellent source of information. The Mining Journal, Ltd., also in London, publishes a weekly journal, a Mining Magazine (monthly), and a Mining Annual Review. The latter covers the field from three aspects: (1) by commodities, (2) through technical developments, and (3) geographically. The Industrial Minerals Directory 1977, 1st ed., Metal Bulletin Books, Ltd., London, provides addresses of organizations in the field. Other useful magazines and periodicals include Engineering and Mining Journal, Pit and Quarry, Rock Products, and World Mining, all published in the United States. In addition many new books related to industrial minerals have been published since the 4th edition of Industrial Minerals and Rocks. Most of these are included in the bibliography of each chapter in this volume. Another excellent information source is the proceedings of the Forum on Geology of Industrial Minerals. This group, which held its 18th annual meeting in 1982, is sponsored by a state geological survey or another mineral agency on a rotational basis. The proceedings have been published by the various sponsors and are available as indicated in Table 1. Two major sources of basic industrial mineral and rock data in the United States, and also a good source for many foreign countries, are the US Geological Survey and the US Bureau of Mines. The two agencies publish many reports and maps on a variety of geological and mining subjects. In addition, each agency has an indexed list of all their publications with a free service announcing new publications: New Publications of the Geological Survey, US Geological Survey, 329 National Center, Reston, VA 22092 and New Publications-Bureau of Mines, Publications Distribution Branch, US Bureau of Mines, 4800 Forbes Ave., Pittsburgh, PA 15213. The US Bureau of Mines (USBM) publishes annually Minerals Yearbooks which provide statistical data on mineral products including production, consumption, imports and exports, as well as information on new developments. Another very useful USBM series is called Mineral Facts and Problems. Editions were published in 1960, 1965, 1970, and 1975. Four major series of publications by the Bureau are Information Circulars, Reports of Investigations, Mineral Trade Notes, and Minerals and Materials. The last two are particularly good for news of foreign developments. The Bureau of Mines Employee Directory, available at all USBM offices, lists addresses and telephone numbers for all offices as well as same for all commodity and area specialists.

Jan 1, 1983