Search Documents

By Chapman Young, Donald E. McCarthy

Many hard rock tunneling projects, where the majority of excavation can be accomplished with TBMs, will still require considerable specialized excavation which can not be done with a TBM. This secondary excavation, involving cross cuts, galleries, flattening of the invert, increases in bore diameter, et cetera, may be accomplished with conventional drill and blast, applied on a small scale and usually with fracture control techniques, or with mechanical splitters. The problems of using explosives in many of these cases and the high cost of mechanical splitting excavation make the consideration of other approaches attractive. The PCF rock excavation method, which has recently been reduced to commercial practice for mine-development excavation, offers an attractive alternative to drill and blast and mechanical splitters. With the PCF method the rock is excavated utilizing a small-charge, propellant-driven, controlled, penetrating-cone fracture process. Excavation is carried out continuously by combining the PCF hardware with integrated mucking capabilities on a carrier which remains at the excavation point. In addition to the benefit of providing for complicated excavation geometry, the PCF method also causes minimal damage to the remaining rock which will significantly reduce ground support requirements. In very bad ground, the continuous nature of PCF excavation allows ground support to be applied as limited sections are exposed thus reducing both the duration and extent that the ground would be free to move. Data on PCF excavation parameters, as measured in actual mining operations, indicate that crosscuts, galleries and the like could be excavated at considerable cost savings compared to drill and blast or mechanical splitters.

Jan 1, 1995

In a previous paper in these Proceedings(l) it was shown from a study of the bore'logs and analyses then available, that the brown coal seams of the Latrobe Valley areas show progressive changes in composition with increase of stratigraphic depth, equivalent to a rise in rank: These changes appear as:(i) An increase in ultimate carbon and hydrogen, calculated on a dry, ash-free basis, and(ii) An increase in calorific value, calculated on the, same basis, each of the order of 1% per 100 ft. of depth, and(iii) A decrease in moisture content of the order of 0.5% to 1.0% per 100 ft. of depth. The decrease in moisture content was found to be less regular than the other changes. In some bores the moisture content remained more or less constant throughout a single seam, or fluctuated slightly, decreasing stepwise on passage to the seam below.It was noted that individual analyses within a bore showed irregular fluctuations, tending to mask the general trend in composition change. This was particularly so for the moisture content, which had been determined for 10 ft. lengths of core, whereas the other components were determined for 50 ft. lengths of core. Averaging of the moisture contents over 50 ft. lengths reduced the masking effects of these irregularities. The suggestion was made that these irregularities arose from variations in the relative proportions of pollen, resin, wood (lignite) and woody attritus composing the core. Such variation in the coal seams has since been established in some detail for the...

Jan 1, 1948

By G. J. Borbely, E. A. Devuyst, V. A. Ettel

Introduction Of the techniques reported for cyanide removal from effluents, alkaline chlorination is the most common (Fisher and Wasser, 1969; Reidt, 1969). Shortcomings with this technique are the high reagent costs, chlorine contamination, and potential formation of cyanogen chloride. Chemical oxidation methods are also not suitable to remove cyanide from effluents containing sulphides in suspension, such as flotation tailings. An inexpensive method for removing cyanide, combined cyanide and related species from waste waters has been developed in Inco laboratories. The method is based on the use of sulfur dioxide (or a sulfite), lime, and air as the reagents. The decomposition reactions of cyanide, combined cyanide, and related species are catalyzed by copper in solution. Complete removal of cyanide species, most of which are oxidized to cyanate, is obtained by treating copper containing cyanide effluents with sulfur dioxide-air mistures while maintaining the pH between 6 and 10 with addition of lime. The new approach can also be applied to selective destruction of cyanide and combined cyanide in effluents containing sulphides in suspension, such as pyrrhotite. Again, a sufficient amount of dissolved copper must be present or added. Metals and precious metals present in the effluents are recovered as hydroxides by adjusting the pH of the treated effluents to about 9-10. Using the new method, the anionic species are removed in the following order: Free CN- > Complex CN- > Thiocyanate The above removal sequence is unusual as oxidants such as chlorine and ozone oxidize thiocyanate preferentially over the combined cyanide.

Jan 1, 1985

By B. Kruger

After the milling and flotation of the platinum bearing ore, the flotation concentrate is electrically smelted in 6-in-line electric arc furnaces and the resulting furnace matte treated in Peirce Smith converters to remove the iron. The iron-free (less than 1% Fe) converter matte is granulated and sent to the base metals and precious metals refineries for further processing. During the smelting and converting processes two distinct gas-strength gas streams are produced: ?The Peirce Smith converter off-gas contains 4%?9% SO2which is treated in a conventional sulphuric acid plant to produce 94% H2SO4. ?The electric furnace off-gas contains 0.9% SO2which was (until September 2002) vented through a 91- metre high stack to atmosphere. In October 2002 Impala Platinum commissioned a SULFACID® plant at its smelter in Rustenburg, which recovers the SO2from the electric furnace off-gasses into a weak sulphuric acid solution. The SULFACID® technology utilizes wet activated carbon to oxidize the SO2toSO3. The SO3reacts with the water on the catalyst and is washed off the catalyst bed as a sulphuric acid solution with up to 13 wt. H2SO4. The plant operates at 60ºC and at atmospheric pressure. The SULFACID® technology is widely used in the pigment industry. This is, however, the first application of the technology on electric furnace off-gas. Keywords: SO2, sulphuric acid, electric furnace, off-gas, SULFACID®

Jan 1, 2004

By Henry B. Kaeding

This paper presents the results of experiments in the treatnient of the gold-bearing ores of the Pis Pis district, near the Atlantic coast of Nicaragua, C. A. Up to the present time, the methods in use in this section of the country for the extraction of the values from the ores have been of the crudest, and the waste has been criminal in its enormity. The transportation of heavy machinery being difficult and costly, recourse has been had to flimsy and inadequate installations, involving great wastes in operation. In some places $15 ore is considered the lowest workable grade. One mine that came under my observation had a 7-ft. vein of $23 ore when examined for purchase; it has been running for years and is now deeply in debt. The future metallurgy of these ores must depend upon chemical, mechanical, and economical considerations—the last being, of course, a resultant of the two former, discussed in the light of prevailing or realizable commercial and industrial conditions. I. Chemical. The ores consist principally of quartz, carrying galena, pyrite, marcasite, and chalcopyrite, and occasionally magnetite, hematite, pyromorphite, and sphalerite, in which minerals the gold lies. The quartz veins occur between malls of andesite, " porphyry," or dioritic rocks, occasionally limestone and dacite. Often the dacite itself is heavily ribbed and filled with auriferous quartz, and is mined as ore. Owing to the excessive rainfall of the country, the ores above water-level have been oxidized and leached of their sulphides, and have become in that operation highly acid and free from

Jan 1, 1912

Urban railway systems need high invest- ments, especially if their routes and stations have to be placed in the subsurface. In the FRG the construction and equipment cost of urban underground railway systems are in the range of 60 to 100 Mill DM per km tunnel. For this reason, track sections on the surface and on elevated structures are used as far as that is possible. Considering whole systems, the costs are in a range from to 45 Mill DM per km length for a metro system with about 80 % of its tracks and stations in tunnels and from 20 to 25 Mill DM per km for a light railway system with about 25 % subsurface infra= structure. The amount of route lengths in tunnels depends on the size of a city, the situation regarding above ground structure and free space on the surface, the level of service quality which has to be achieved with the railway system etc. Despite of the urgent needs to improve the transport conditions there very often arise doubts if an urban railway system is really necessary and can be justified in an economic sense. The experience from many cities around the world shows, that there arise a lot of benefits from urban railway systems, especially with larger sections placed under- ground. They are to be found in the interests of the operator (f.e. operating costs), the user (travel time, quality of service etc.) and regarding social aspects (environmental protection, accidents, consumption of energy Etc.).

Jan 1, 1987

By J. Jolly

THIS short note on the probable character of the organic sulfur compounds in coal can do no more than indicate lines of research. We have no new experimental work to describe, nothing comparable in value with the careful studies of American coals by Powell and Parr1 and Yancey and Frazer.2 A study of the manner in which sulfur compounds exist in British coals (and their behavior on heat treatment) is rendered increasingly necessary by the fact that the British reserves of good coking coals of reasonably low sulfur content are fast being depleted. We believe that it is essentially by a study of the modes of formation, occurrence, and decomposition of the various types of inorganic and organic sulfur compounds in coal that it will be possible, with hope of success, to attack the problem of purifying coals, otherwise eminently suitable for coking, from these objectionable ingredients. Sulfur, so far as is at present known, does not normally occur in the free state in the coal conglomerate, but is chiefly distributed, irregularly, in three forms: 1. As primary constituents of the coal conglomerate, organic in nature and probably associated with those molecular complexes that have resulted from the degradation of the proteins of the plant tissues responsible for the formation of the coal mass. These constituents can be classed as "organic sulfur." 2. As metallic sulfides, e.g., iron pyrites. 3. As metallic sulfates, e.g., calcium sulfate and ferrous sulfate. (The occurrence of these compounds varies with the occurrence and degree of degradation of class 2.)

Jan 3, 1925

By Robert Richards

Introduction. WALTER RENTON INGALLS recently gave a very interesting talk before the student mining society of the Massachusetts Institute of Technology. In it he showed the present status of mining as he sees it. In the talk he explained that, while discoveries of great mining districts are still possible, they are being made less and less often; that the great mining companies, although there are large numbers of mines offered for sale, are finding it less and less possible to find new mines that are up to the standard of richness that they wish for purchase. The natural conclusion is that better, cheaper, and more efficient methods of mining, concentrating, and smelting are needed if the lower-grade mines are to be worked at a profit. This is true also if the high-grade mines are to yield their greatest profit. This paper deals only with the concentrating or ore-dressing problem, and gives some thoughts which point towards greater profit. In a paper on The Development of Hindered-Settling Apparatus the writer showed that there were two main lines of work that would lead to greater saving, lower tailing assay, and, therefore, greater profit. The first is the recrushing of middling or tailing products for the saving of the contained values. This is well understood and largely carried out in existing mills. The second is the saving of fine free mineral at the first opportunity. This is a matter less well understood in the mills, and to dwell upon this the present paper is written.

Jan 9, 1913

By Bernard Schneider

The diversity of methods available to engineers and geologists for studying rock masses is a reflection of the fact that, despite the rapid and encouraging progress made over the last few years, there is still no unified and comprehensive method which can be used to predict the over- all behavior of a foundation. Nevertheless, it is agreed that the fundamental characteristic affecting the engineering properties of rock is fissuration, and this paper de- scribes a few new or improved methods of studying fissuration and its influence on major engineering factors such as permeability, deformability, or internal stresses in the rock volume. TESTS ON SAMPLES Conventional tests on samples using thin slices can be improved by staining the slices before cutting with certain ionic dyes which have an affinity for certain types of surface. This shows up the microdiscontinuities. For example (quoted terms are French trade names) : "Turquoise Motylhne JSA" will show up porous alteration of basic feldspars. "Vert brillant SA" is used for acid feldspars. "Fushine ASA" will show up voids in all rocks. A mixture of "Turquoise" and "Rhodamine BSA" will show up zones of alteration in all types of feldspars. With this technique, it is easy to make an optical classification of the different structural types, e.g.: (1) rocks completely free from voids; (2) rocks with microfissures, which in turn can be subdivided into (a) rocks with microfissures secant to the mineral structure, (b) rocks with microfissures parallel to the mineral structure, and (c) rocks with ran-

Jan 1, 1970

By P. de Vitry, Willis P. Mould

The wire saw is a tool not less than 60 years old, probably nearer 100 years old. It was developed in Europe and is reputed to have originated in Belgium. Frombold is said to be the original patentee. Wire sawing equipment, as indicated in Fig. I, is very simple. It consists of a three-strand wire cable, usually pis or 1/4 in. in diameter, or a single flat ribbon of medium hard, tough, alloy steel twisted into a helix of those diameters, made to form an endless belt of any length up to several thousand feet. The wire is guided into the cut by sheaves mounted in slides on steel columns situated close to either end of the cut. The feed motion usually is controlled either by gravity or by hand-operated feed screws. The steel columns or "standards" range from 15 to 30 ft. in length. At the top is a swiveled arm supporting a sheave similar to the traveling sheave below. Immediately under the swivel-mounted sheave is a guy plate or collar with shackles attaching four chain or wire-rope guys with suitable tightening devices, or with two guys and two jack legs for supporting the standard vertically or at any desired anale. The usual drive is by a 10-hp. motor through a gear reducer, on which are Insti- two grooved sheaves, One of which is keyed and the other free running On the shaft. Tension is provided by a car running on a track in line with the driving sheave

Jan 1, 1948

By David Cole

DAVID COLE, EL PASO, TEXAS (communication to the Secretary*).-I have read with great interest Dr. Gahl's painstaking paper giving us the details of development of flotation at Inspiration, and it seems to me that he has covered the ground so completely that there is little to discuss or criticize in connection with his subject. While it was in operation, the test mill in which the campaign was carried on was the Mecca of mill men and metallurgists. There was much to interest students of milling methods in addition to the flotation experiments, and readers of Dr. Gahl's paper will miss the information they hoped to get when the "pilot" mill results were. finally compiled, and I hope that the following remarks outlining from a distance some of the things that happened there will bring forth the rest of the story of the performances recorded in these important experiments. Prior to the use of flotation methods in concentration it had long been recognized that the "unavoidable" losses of sulphides were in the slime which is inevitably produced in the grinding operations required to free the minerals to be separated. Classifying the feed prior to its final stage of treatment had long been in style in milling. This assisted the sand-handling machines and resulted in lowering the tailings made by them, but at the expense of the slime-handling department; and while little was expected of the latter, the wisdom of complicating the process by hydraulic classification was being seriously questioned. Indeed, at the

Jan 10, 1916

By P. de Vitry, Willis P. Mould

The wire saw is a tool not less than 60 years old, probably nearer 100 years old. It was developed in Europe and is reputed to have originated in Belgium. Frombold is said to be the original patentee. Wire sawing equipment, as indicated in Fig. I, is very simple. It consists of a three-strand wire cable, usually pis or 1/4 in. in diameter, or a single flat ribbon of medium hard, tough, alloy steel twisted into a helix of those diameters, made to form an endless belt of any length up to several thousand feet. The wire is guided into the cut by sheaves mounted in slides on steel columns situated close to either end of the cut. The feed motion usually is controlled either by gravity or by hand-operated feed screws. The steel columns or "standards" range from 15 to 30 ft. in length. At the top is a swiveled arm supporting a sheave similar to the traveling sheave below. Immediately under the swivel-mounted sheave is a guy plate or collar with shackles attaching four chain or wire-rope guys with suitable tightening devices, or with two guys and two jack legs for supporting the standard vertically or at any desired anale. The usual drive is by a 10-hp. motor through a gear reducer, on which are Insti- two grooved sheaves, One of which is keyed and the other free running On the shaft. Tension is provided by a car running on a track in line with the driving sheave

Jan 1, 1948

By E. T. Turkdogan

The activities of SiO2, FeO, and Fe2O3 are calculated from previous experimental data on the activity of oxygen in Fe-Si-O melts at 1550°C. Using the oxide-activity data, the free energy of formation of fayalite from its oxides is evaluated for 1550°C. A number of investigators1-4 contributed to the study of the state of oxidation of iron in SiO,-FeO-Fe,O3 melts and the phase equilibria in the system Fe-Si-O. In a more detailed study, Schuhmann and Ensio5 and Michal and Schuhmann% easured the state of equilibrium in the SiO,-FeO-Fe,O3 melts saturated with y-iron or silica or both under low-oxygen potentials and within the temperature range 1250" to 1350°C. Similar measurements were also made by Turkdogan and Bills7,' over wide ranges of composition and oxygen potentials at 1550"C. Using the experimental data on the oxygen activities in the ternary system, Schuhmann' calculated the activities of silica and ferrous oxide in Si0,-FeO-Fe2O3 melts for 1350°C. Adequate knowledge on the activities of the constituent oxides of melts is essential in the study of reaction-equilibria and reaction-kinetics in oxide-melts. With this in view, the activities of oxides in SiO2-FeO-Fe2O3 melts at 1550°C are computed using the experimental data of Turkdogan and Bills7'8 on the oxygen activities in these melts.

Jan 1, 1962

By P. de Vitry, Willis P. Mould

THE wire saw is a tool not less than 60 years old, probably nearer 100 years old. It was developed in Europe and is reputed to have originated in Belgium. Frombold is said to be the original patentee. [ ] Wire sawing equipment, as indicated in Fig. I, is very simple. It consists of a three-strand wire cable, usually 3/16 or 1/4 in. in diameter, or a single flat ribbon of medium hard, tough, alloy steel twisted into a helix of those diameters, made to form an endless belt of any length up to several thousand feet. The wire is guided into the cut by sheaves mounted in slides on steel columns situated close to either end of the cut. The feed motion usually is controlled either by gravity or by hand-operated feed screws. The steel columns or "standards" range from 15 to 30 ft. in length. At the top is a swiveled arm supporting a sheave similar to the traveling sheave below. Immediately under the swivel-mounted sheave is a guy plate or collar with shackles attaching four chain or wire-rope guys with suitable tightening devices, or with two guys and two jack legs for supporting the standard vertically or at any desired angle. The usual drive is by a 10-hp. motor through a gear reducer, on which are mounted two grooved sheaves, one of which is keyed and the other free running on the shaft. Tension is provided by a car running on a track in line with the driving sheave

Jan 1, 1946

By P. Somasundaran, I. J. Lin

There are several methods described in the literature for the determination of the order and the rate constant for the flotation of minerals. These often involve some type of computational or graphical procedures. A relatively simpler method developed on the basis of a technique used by Chang" in chemical kinetics is described in this paper. Chang's technique, like most others in chemical kinetics," is based on the law of mass action which states that the rate of a chemical reaction is proportional to the active masses of the reacting substances at any given time. Application of this law to the flotation of minerals would involve the adaptation of the terms "flotation" for "chemical reaction" and "floatable amount of the minerals" for "the active masses of the chemical reactants." There are indeed a large number of physical processes controlling the actual flotation rate. The most inefficient one of these could be considered equivalent to the slowest reaction in a series of chemical reactions. If variables such as aeration rate and agitation are kept at constant levels, the rate of flotation under free flotation conditions (i.e., conditions under which the suspension is dilute) will be given by the following equation: where C is the concentration of the floatable minerals in the pulp at any given time t, K is the rate constant, and n is the order of the reaction. If we represent the floated fraction of the floatable mineral at time t as m (0 m - 1) and C at t = 0 as Ca, integration of Eq. 1 yields

Jan 1, 1974

By T. W. Guy

DURING recent years, tremendous strides have been made in the economical use of coal. This has resulted in, and to some extent has been a result of, making the fuel specifications more and more rigid. For this reason, all producers have found it necessary to improve their preparation materially, both as to sizing and the elimination of impurities, either by more effective preparation underground or at the tipple and cleaning plant, or both. This cause and its effect in all producing fields seem likely to continue for several years-at least. The splendid inherent qualities of the Pocahontas and New River coals are known all over the world, but their good reputation is only partly due to inherent qualities, and to natural conditions which generally favor loading coal comparatively free from impurities; it is due in large measure to the care and skill used, either with or without the aid of mechanical devices, to ship products consistently low in ash. The first coal from the West Virginia smokeless fields was mined and shipped near Quinnimont, on New River, in 1871, while the first shipments from the Pocahontas field were in 1883. The development of both fields progressed rapidly. At first activities followed the main lines of the Chesapeake & Ohio and Norfolk & Western railroads, and were extended later as branch lines were built from these roads. The Virginian R. R., about 1907, opened up the Winding Gulf territory, which has since become a large producer of smokeless coals from the Pocahontas and the New River measures.

Jan 1, 1931

By James Norman

SPODUMENE is a lithium-bearing pyroxene, and is an important source of lithium compounds. Because of its high alumina and lithia content, it might be a desirable constituent of glass batches. The use of spodu-mene in ceramics will undoubtedly increase, as it has been shown that a mixture of the proper proportions of this mineral with soda feldspar and potash feldspar has a much lower maturing temperature upon firing than has any one of the three components.1 The mineral spodumene seldom occurs as pure mineral, but ordinarily with feldspars, mica and quartz. All spodumene-bearing rocks tested contained these minerals as gangue. Small amounts of iron and manga-nese oxides also were present, usually as stains on the silicate grains. Mica associated with the spodumene carried a considerable amount of lithia. This was discovered in flotation tailings, which, although virtually free of spodumene grains when examined microscopically, showed 0.4 to 0.5 per cent Li2O on chemical analysis. The lithia content of micas picked from the North Carolina spodumene rock was variable. Some samples contained little lithia, others more than 3 per cent. In 1938, under the supervision of Oliver C. Ralston, ? the Bureau of Mines, in cooperation with the Tennessee Mineral Products Corporation, undertook to study the beneficiation of North Carolina spodumene by froth flotation. The Bureau had previously published investigations on the beneficiation of spodumene.2,3 The methods described in the second publication' did not give good results with badly weathered spodumene rock, so that more thorough investigation of the subject was warranted.

Jan 1, 1940

Economic Significance of High-grade Concentrates BY PAUL M TYLER AND CARLE R HAYWARD (Min & Met, Dec, 563 4000 words) Generally pyro¬mctallurgical methods yield a higher recovery but cost more per ton of ore treated Milling methods are inherently cheaper for the reason that they do not involve dissipa¬tion of heat energy in slag formation, ctc It is vaguely realized that the smelter man could do a better job if he were supplied with purer raw materials but hard¬headed mill men have been offered little inducement to do a really good job of cleaning concentrates To do this may involve some sacrifice in percentage yield and in mill capacity and unless there is a compensating saving in freight and smelter charges, it simply is not good business to go beyond a certain point in the way of making clean concentrate Opportunities exist for eliminating one or more steps in the expensive series of processes for recovering various metals, or at least reducing the volume of materials that has to be handled at the most costly steps The beneficiation of nonmetallic minerals likewise affords numerous examples of over-all economies obtainable through more refined methods of mechanical improvement All this leads to the conclusion that perfecting selective processes for isolating pure minerals (e g, galena) virtually free from other sulfides as well as gangue may be productive of industrial economies Conversely, cheapening smelting methods may invade the field of mechanical improvement of ores but, as Kiphng said, that is another story

Jan 1, 1937

[ ] Utilizing tendencies for low grade ores in the Sudbury District of Ontario to cave after higher grade ore has been mined, International Nickel Co., of Canada, Ltd., is recovering millions of tons of nickel-copper ore once regarded as submarginal. Inco is working lower grade ore than ever mined before from its underground operations because of the caving method and metallurgical practices. In the caving method, blocks containing as much as 1.5 million tons of ore are undercut. As ore from the undercut block is withdrawn, the block to be mined breaks away and starts to disintegrate as it moves downward. Inco is also using the blasthole method, using explosives to break slices of harder, tougher ore from solid material. Inco has built a new concentrator at one of its most recent shafts for handling the increased tonnages of low grade ore. The concentrator presently has a 10,000-ton per day capacity, and is scheduled to be increased to 12,000 tons. Hoisting from the mine is by push-button control and the ore is milled on the spot. A 7 ½ -mile pipeline carries bulk concentrate to reduction plants at Copper Cliff. Giant crushers, weighing 165 tons each, have been installed underground. Twenty-ton electric locomotives haul ore to the crushers. The expansion program is expected to lift total annual production of nickel in the free world to 375 million pounds annually, an increase of 150 million pounds. Inco is presently mining more than 1 million tons of ore per month from combined surface and underground operations.

Jan 1, 1952

By G. H. Billings

There exists an unconfirmed opinion among many ironmasters that the combination of a small quantity of manganese, chromium, titanium, tungsten, aluminium, nickel, and some of the metalloids with iron has a beneficial effect upon the quality. And the impression prevails in some localities that the excellence of steel greatly depends upon the influence of some of these elements. Brit as the recorded experiments are so meagrely described, and made under such various conditions, the student in search of information upon the subject is somewhat bewildered by the contradiction of the opinions expressed. Observing some interesting phenomena while experimenting with an alloy of iron, copper, and nickel, I was led to determine the effect of some of the metals upon iron as free from contamination by other elements as it is possible to procure in practice, in order that the result of an alloy of an individual metal with iron might be more closely studied; for it is almost an impossibility to determine the influence of a small amount of one element upon a metal combined with a large amount of another, and the mere presence of another sometimes makes this difficult. And as most of the experiments recorded upon this subject have been made with iron containing sufficient carbon and other elements to interfere with the effect of that metal the influence of which it was desired to observe, I have endeavored to avoid these sources of error as far as practicable. In determining the specific gravity of the alloys in these ex-