Search Documents

By Constantine C. Popoff

The Hermada antimony deposit is in the Sewtooth Range in southwestern Idaho, about 77 miles by road northeast of Boise. Stibnite mineralization occurs over an area one mile wide from west to east and two miles long. It is locally referred to as the Swanholm district. In 1947 high- grade stibnite ore was discovered on the East Fork of Swanholm Creek. Since then, ore in commercial quantity has been produced by the Hermada Mining Co. The total output for 1947-50 was about 5,000 tons of ore, containing 640 short tons of antimony metal.

Jan 1, 1953

By Mary Ellen Bruce Large

"In partnership with California Department of Transportation (Caltrans), Federal Highway Administration (FHWA), and with support from International Association of Foundation Drilling (ADSC), Deep Foundations Institute (DFI) organized a workshop on quality assurance (QA) practices for acceptance of post-grouted drilled shafts in conjunction with DFI’s 40th Annual Conference on Deep Foundations. The 1½-day workshop was held on October 15-16, 2015 at the Oakland Marriott City Center in Oakland, CA.Post-grouting, in the context of this workshop and report, refers to the alternative design and construction of base-grouted drilled shafts wherein a grout distribution system is installed during construction and used to grout the base under pressure after the drilled shaft concrete has gained adequate strength, resulting in a stiffer axial-compression load-displacement relationship and additional possible ground improvement effects.The primary goals of the workshop were to•?Identify and summarize the state of the practice for design, construction, inspection, verification, acceptance criteria, reliability and performance of post-grouting.•?Identify gaps and needs in quality assurance that should be addressed for successful use of post-grouting.This report is structured to follow the workshop program: workshop presentations outlined the state of practice and views from owners, engineers and contractors on acceptance of post grouting methods for drilled shafts; and subsequent workshop discussions attended by a small invited group of participants focused on identifying areas of agreement and disagreement on post-grouting best practices, acceptance criteria, design and verification procedures, and inspection requirements. A partial list of attendees of the open and closed sessions is provided as Appendix A, and copies of presentations are included as Appendix B.FHWA and Caltrans are the primary audiences for this report, and its content will be used to develop a roadmap for deploying the findings into policy and practice. The secondary audience is the broader industry group, and the report content will be disseminated in a variety of formats."

Jan 1, 2016

By A. Panteleyev, C. S. Ney, R. J. Cathro, A. Sutherland Brown

The general distribution of metal deposits in the Canadian Cordillera can be related to its tectonic evolution. The Canadian Cordillera is naturally divisible into five longitudinal tectonic belts within which rocks are broadly similar in type, age and history. From west to east they are the Insular, Coast Crystalline, Intermontane, Omineca and Eastern Marginal belts. Seven classes of metal deposits in the Canadian Cordillera are defined and their characteristics described. These classes are skarn, porphyry, massive sulphide, stratiform, magmatic, copper in basic lavas, and vein deposits. Maps showing the distribution of medal and metal-group concentrations serve to illustrate the relations in space and time between mineralization and geologic evolution.

Jan 1, 1971

By Eugene O. Binyon

"Belt and shaker conveyors, used singly or as combined units, have for many years been an integral part of many coal-mine haulage systems. The belt conveyor has also been used extensively as a main haulage unit in open-pit iron-ore mines of the Lake Superior district, particularly on the Mesabi Range. Few underground metal mines, however, either in the ferrous or non-ferrous branches of the mining industry, use the conveyors exclusively or even extensively for underground haulage. At present, only five iron-ore mines in the entire Lake Superior district have belt- or shaker-conveyor installations of any significant size. Of these mines, three are in the Crystal Falls-Iron River district of Michigan on the Menominee Range, one is on the Marquette Range near Ishpeming, Mich., and one is on the Mesabi Range near Keewatin, Minn.Results of the studies of tackless haulage in the Lake Superior district will not permit the establishment of any formula to prove or disprove the advantages of belt or shaker systems at all underground mines. The studies do show that trackless haulage can be used to advantage where the proper conditions exist. Advantages are particularly apparent when development can be planned sufficiently in advance of exploitation to permit installation of belts or shakers as part of the development program and where the systems are extended to include haulage in stopes as well as main entries.During the winter of 1947-48, the Bureau undertook a study of all of the underground ore conveying systems known to be in operation in the Lake Superior district for the purpose of making available to the entire mining industry the technologic data developed in the area. Because conditions that led to the installation of the belt and shaker conveying systems were often a function of the character of the deposit or the method of mining, a brief description of those conditions is included in this report.After a preliminary investigation into the extent to which trackless conveyors were employed in the district, it was found that a detailed study at five bites would result in fair appraisal of that method of haulage in the underground iron-ore mines.Each of the five significant installations is described separately in this report. In one instance, however, company policy does not permit identification of the mine wherein the conveying is done. In that instance the operation is designated as mine ""A"".Unless otherwise specified, all tonnage figures quoted herein are gross.The cooperation of officials of all of the companies operating underground mines in the Lake Superior district permitted successful completion of preliminary studies of mining practices and conveying systems.Special acknowledgment is made to R. D. Satterley, general superintendent, and to operating staffs of the Sherwood and Morris mines of the Inland Steel Co. The assistance given by W. D. Whitman, assistant superintendent, and Douglas Tippett, mine captain at the Morris mine, and P. D. Pearson, superintendent, R. O. Marsten, engineer, and W. Johnson, mine captain, at the Sherwood mine, is acknowledged."

Oct 1, 1949

The U.S. economy showed further strength during the third quarter of 1983, continuing the upward trend discussed in the last two issues of Minerals and Materials. The National Association of Purchasing Management composite index increased to a 10-year high of 67. 1 in July. (A value of 50 or greater indicates expanding industrial activity.) The index, a weighted composite of new orders, production, employment, vendor performance, and inventories, is derived from a survey of purchasing agents for about 250 industrial firms. Investment and Other National Economic Indicators The strong consumer surge of second quarter 1983 was reinforced during the third quarter by the performance of private investment. Because of this, many analysts became more optimistic about the strength of the recovery and its potential for being sustained. Capital investment growth, negative since 1980, was positive for every investment component in the third quarter of 1983. Preliminary estimates indicate a real increase of $1.4 billion (at an annual rate) in private investment expenditures on nonresidential structures, an increase of $4.3 billion (at an annual rate) for producers' durable equipment, and an increase of $4.8 billion (at an annual rate) in real inventory levels. The second quarter 1983 increase in expenditures on producers' durable equipment was the first indicator that investment recovery would occur during the rest of the year (table 1). Corporate profits in total manufacturing increased $6.5 billion from first quarter to second quarter 1983 (table 2).

Jan 1, 1983

By Leslie S. Weldon

THE Lake Shore mine has been developed by two vertical shafts, with level intervals at 200 feet to the 2200 level and at 125 feet below this horizon. A main cross-cut joins the two shafts on all levels to the bottom of No. 3 shaft, and opening into these cross-cuts are the ore passes and sand passes, which are completed from surface To the 4450 level. In the west part of the mine, additional connections have been made between No. 1 and No. 2 veins, through which the major part of the ore from No. 2 vein west is routed to drifts in No. 1 vein. With the lesser amount of stoping on No. 1 vein, this arrangement permits better haulage to be maintained. The ore passes are driven at 50 degrees from the ends of short cross-cuts off the main ones and are broken through to the levels above at the mouths of the short cross-cuts, to allow for dumping on each level. The passes are controlled at each level by ball-and-chain gates and deliver to crushers and thence to loading pockets, shown in Figure 1. That system is quite flexible in that it is possible to by-pass the crushers at any station and load from either shaft at a number of different pockets. The sand passes are driven from the main cross-cuts at the same inclination as, and parallel to, the ore passes. Each is equipped with a chute and dump hole, so that waste or sand fill may be loaded or dumped at each level. A transfer door, hinged on the bottom, is installed opposite the chute for by-passing fill from one level to the next, and in the closed position protects the opening at the top of the pass. The dump hole situated beside the transfer door is protected by a grizzly with 10-inch spaces. Waste rock may be withdrawn from the system through No. 3 shaft loading pocket at the 2950 level to a waste bin on surface. Levels are developed by drifts in No. 1 and No. 2 veins for their entire lengths. Subsidiary breaks are followed at a later date, when full information has been obtained by exploration, and a considerable amount of development by sub-drifts is carried out in the upper part of the mine, particularly in more or less erratic sections of No. 1 vein.

Jan 1, 1936

General economic conditions continued to improve in the second quarter of 1984 as real gross national product advanced at an annual rate of 7.5 percent (table 1). This followed an even larger first quarter annual rate increase of 10.1 percent. The slower second quarter growth was greeted as a sign that the economy is not over-heating. The signs of slowed growth in some sectors suggest that the recovery may continue well into 1985 without the inflation symptomatic of a rapid recovery. Most of the slowdown in growth was absorbed by business inventories, personal consumption of durable goods, and residential fixed investment. Business inventories grew by only 68 percent as much as in the first quarter, personal consumption for durable goods grew by 58 percent of the first quarter rate, and residential fixed investment slowed to only 44 percent of the first quarter growth. Sectors with accelerated growth in the second quarter included personal consumption of nondurable goods and of services, which increased at annual rates of 9.6 percent and 3.8 percent, respectively, and Federal purchases of goods and services, which increased at an annual rate of 47.9 percent.

Jan 1, 1984

Dry weather since the third week in January has set back any prospects for an early increase in hydroelectric power in the Pacific Northwest, according to The Bonneville Power Administration. The 25% cutback made in July probably will not be restored in March or April. Noranda Aluminum, Inc., increased its price for 99.5% aluminum ingot from 66 cents to 70 cents per pound effective March 1, 1980. Revere Copper & Brass, Inc., also -increased its price for primary aluminum from 66.0 cents to 70.0 cents per pound effective February 1. Kaiser Aluminum & Chemical Corp. raised its international price for 99.5% primary aluminum from 72.6 cents to 82.6 cents per pound, c. i. f., effective February 26 on new orders and on shipments from March 15.

Jan 1, 1980

The United States has not begun commercial operations to tap its largest poten-tial sources of oil supply - oil shale and coal. The reason is that domestic petrol-eum has been plentiful in the past and liquid products probably could be produced from it at the lowest cost. In view of the ever-increasing need for petroleum in the United States, the critical international situation threatening foreign supplies, the growing demands for steel, and the heavy costs to industry of constantly discovering and developing new oil fields, it is believed that the prompt development of a synthetic fuel industry based on oil shale and coal is not only requisite to safeguard our oil supply but is an economically sound course for the foreseeable future, To neglect its development is to close our eyes and minds to our own resources at a time when they are needed critically. It also is apparent now that neither the Government nor industry would be taking any considerable economic risk in starting the initial plants, especially as measured against their potential value in meeting critical oil and chemical demands and in building a new industry in the West.

Jan 1, 1951

By D. J. Parker

On Thursday, March 18, 1937, the country was shocked by news of a terrific explosion at the New London, Tex., school, which caused the death of 280 pupils rind 14 teachers. The explosion occurred at about 3:05 p.m. in the largest of the 11 school buildings on the campus. Figure 1 shows this building, market; "Main high school building?, with respect to other buildings, pipe lines, oil wells, and gas lines on the property.

Jan 1, 1937

By Robert R. Perron

The U.S. Bureau of Mines is engaged in many diverse programs for improving mine safety. Of particular interest to the Bureau are new and improved means for minimizing the hazard of fire which can be initiated by prolonged low energy electrical faults on trolley line systems. When a high energy fault occurs on a trolley line, wherein the current exceeds the magnitude normally drawn by legitimate loads, such as locomotives, then the circuit breakers at close-by power rectifier sets trip. Tripping of the breakers not only protects the equipment at the rectifier sets, but also disconnects the energy source from the fault and thereby minimizes the fire risk. However, the fault current is frequently of a level substantially below that required to trip the overload breakers. When the fault is a substantial percentage of the set level of the breakers, the energy dissipated by the fault is frequently sufficient to clear the system by rapidly burning itself clear. Such a fault is often short-lived and does not present as serious a fire risk hazard as a prolonged, much lower energy fault, wherein the energy level is too low to clear the system. The breakdown of a trolley line insulator, in which there was a 20 or 30 ampere leak, would represent such a fault or illegitimate load and a substantial fire risk.

Jan 1, 1974

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include better fire suppression systems, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By Mary Ellen Bruce Large

"INTRODUCTIONIn partnership with California Department of Transportation (Caltrans), Federal Highway Administration (FHWA), and with support from International Association of Foundation Drilling (ADSC), Deep Foundations Institute (DFI) organized a workshop on quality assurance (QA) practices for acceptance of post-grouted drilled shafts in conjunction with DFI’s 40th Annual Conference on Deep Foundations. The 1½-day workshop was held on October 15-16, 2015 at the Oakland Marriott City Center in Oakland, CA.Post-grouting, in the context of this workshop and report, refers to the alternative design and construction of base-grouted drilled shafts wherein a grout distribution system is installed during construction and used to grout the base under pressure after the drilled shaft concrete has gained adequate strength, resulting in a stiffer axial-compression load-displacement relationship and additional possible ground improvement effects. The primary goals of the workshop were to•?Identify and summarize the state of the practice for design, construction, inspection, verification, acceptance criteria, reliability and performance of post-grouting.•?Identify gaps and needs in quality assurance that should be addressed for successful use of post-grouting.This report is structured to follow the workshop program: workshop presentations outlined the state of practice and views from owners, engineers and contractors on acceptance of post grouting methods for drilled shafts; and subsequent workshop discussions attended by a small invited group of participants focused on identifying areas of agreement and disagreement on post-grouting best practices, acceptance criteria, design and verification procedures, and inspection requirements. A partial list of attendees of the open and closed sessions is provided as Appendix A, and copies of presentations are included as Appendix B.FHWA and Caltrans are the primary audiences for this report, and its content will be used to develop a roadmap for deploying the findings into policy and practice. The secondary audience is the broader industry group, and the report content will be disseminated in a variety of formats."

Jan 1, 2016

By D. J. Parker

On Thursday, March 18, 1937, the country was shocked by news of a terrific explosion at the New London, Tex., school, which caused the death of 280 pupils avid 14 teachers. The explosion occurred at about 3:05 p.m. in the largest of the 11 school buildings on the campus. Fire 1 shows this building, marked "Main high school building", with respect to other buildings, pipe lines, oil wells, and gas lines or the property.

Jan 1, 1937

By G. E. McElroy

As one phase of a general program of enthracite mine-fire research initiated by the Bureau of Mines in September 1935, a study of the records of past fires was considered a necessary approach to a proper understanding of present and future fires because only limited information could be obtained directly from existing active fires on account of their inaccessibility. Through the courtesy of interested operators, all available records of fires that had occurred in a large group of steep-pitch anthracite mines in the Western Middle and Southern fields of the Pennsylvania anthracite district were examined and analyzed for data on the causes, costs, behavior, and control of fires, and this report is primarily a discussion of these factors based on a close study of these particular records. Mining Conditions The records pertain to a group of mines that have contributed about 12 percent of the total Pennsylvania anthracite production and constitute a large proportion of, and well represent, steep-pitch operations in this district. Throughout the area represented, the coal occurs as a series of up to 20 parallel seams in folded slate and sandstone strata and almost entirely on pitches of 400 to 80°, with vein thicknesses of 5 to 60 feet. Practically all are old mines with histories dating back to 1850, or thereabouts, and present operations are either under or adjacent to mined-out areas extending to surface or to the saddles of anticlines. All operations are at relatively shallow depths, that is, within 1,000 feet, vertically, of the surface. Mining methods are largely a heritage of the past and embrace typical breast and pillar operations with practically no mechanized mining and with the coal shot ?off the solid.? Most of the mines are rated as gassy and are operated now on a closed-light basis. Permissible explosives are now used entirely for breaking coal, and dynamites for rock work and chute-starting blasting.

Jan 1, 1938

By George S. Rice

"INTRODUCTION During the past 4 or 5 years the frequent occurrence of bumps in coal mines of the Cumberland field, in Harlan County, Ky., and Wise County, Va., has caused much apprehension among miners and mining officials of that region.These bumps have caused many deaths and injuries, and have been increasing in frequency. Eight men were killed and a number injured by bumps in the first 4 months of 1934. Their unpredictable occurrence and the usual absence of any preliminary warning tremors or sounds, such as ordinarily precede a large fall of roof, cause fear of other bumps and impair the morale of mine workers.Acknowledgments This report on bumps in coal mines of the Cumberland coal field of Kentucky and Virginia is based on an investigation made at the urgent request of .the Harlan County Coal Operators Association, through James F. Bryson, director of safety of the association, to the Director of the United States Bureau of Mines, following a series of disastrous bumps in. Harlan County, Ky., and Wise County, Va. The request was granted and the writer detailed to undertake the investigation, which was made in June 1934.The officials of certain operating companies in the Cumberland field gave every facility for examining the conditions accompanying bumps in their mines. The writer is most grateful to them for the courtesies shown; to J. F. Bryson, to J. F. Davies, district engineer, Safety Division, U. S. Bureau of Mines, who accompanied the writer throughout his trip to the vari¬ous mines and gave him much assistance and detailed information regarding the occurrence of bumps; and to Dr. David White for reviewing the geological descriptions,Definition of Bumps ""Bumps"" are phenomena comparatively rare in the coal fields of the United States and, for that matter, in the coal fields of the world, because for their occurrence certain exceptional natural conditions are required strong, massive strata of sandstone or conglomerate above the coal and a fairly strong floor, as will be described in detail later."

Jan 1, 1935

On July 1, the Bonneville Power Administration announced a 25% power cutback because of lower than normal stream flow. In September, the Aluminum Company of America (Alcoa) announced plans to shut down one 23,000-ton-per-year potline at its Vancouver, Wash., primary aluminum smelter. Alcoa also announced that the last of four potlines at its Point Comfort, Tex., primary aluminum smelter would be restarted in October. A new 3-year contract was signed and workers at three Alcan Aluminum Ltd. primary aluminum smelters in Canada returned to work. It was estimated that it would take about 3 months before the smelters were operating at full capacity.

Jan 1, 1979

By Julius G. Chang

Against the receding background of the October stock market crash and the December overhang of inventories, the economy began with a shaky start in 1988. As 1988 began, the Administration's estimate of real growth for 1988 had just been reduced from 3.5% to 2.4% and economists and other ob-servers were concerned that the expansion that was 5 years old might be near the end and that a recession might be around the corner. The ensuing moderately strong economic activity, however, belied all the negative signals that were evident earlier, and the real GNP continued to grow at an estimated 2.3% annual rate during the first quarter of 1988, extending the ongoing recovery into the sixth year (table 1.). The relatively accommodative policy of the Federal Reserve Board (the discount rate was cut by 0.25% in January), a strong performance by the export sector, and the revival of consumer spending were major forces underlying the economic strength. But as the quarter drew to a close, signs of tight capacity utilizations were apparent in many of the export and capital goods sectors, including textile, chemical, plastic, metal, and machinery. Employment was at a record high level while the unemployment rate was close to a historical low. Prices were rising at a faster pace than those of 1987, and the dollar resumed its slide after a brief recovery in January and February. These factors gave rise to the fears of higher inflation. Long-term interest rates increased, casting a pall over the prospect of a robust growth for the rest of the year.

Jan 1, 1988

By Edmund Newton

The Haile mine has been the outstanding gold-mining operation and the largest single producer of gold in the Appalachian region. Gold was discovered at the Haile in 1827, previous to the present operation, production has been nearly $4,500,000 (gold at $20.67 per ounce.) from somewhat over a million tons of ore, with an average extraction of about 70 percent. The Haile property, now operated by Haile Gold Mines, Inc., is in the southern part of Lancaster County, South Carolina, 3-1/2 miles northeast of the town of Kershaw and 55 miles north of Columbia, the State capital. (See fig. 1.) The corporation has a lease and purchase contract on 1,805 acres, covering the present productive area. In addition, it holds lease contracts on 1,500 acres additional adjacent to this area.

Jan 1, 1940

By C. M. Diaz

The chemistry of the main unit processes in nickel extractive pyrometallurgy is reviewed. Key re1a ions between smelter feed composition and process selection are discussed, with particular reference to operating conditions, energy requirements and products. The paper a1 so includes a brief discussion of current nickel smelters, based on the results of a recent survey carried out by TMS.

Jan 1, 1988