Search Documents

By S. P. Lowe

Flotation testing of Flin Flon ore was started in the Denver laboratory of Complex Ores Recoveries Co. in March, 1926. There had been a considerable amount of flotation testing previously which had shown possibilities of success, and it was felt that, with the increased knowledge of flotation and the comparatively new reagents then available, flotation held out the best prospects for a successful commercial treatment of this ore. There remained available for this experimental work a small amount of the rejects from a thorough sampling of the mine and some ore from the mine dump.

Jan 1, 1930

By Matej Petružálek, Václav Vavrycuk, Tomáš Svitek, Tomáš Lokajícek

The most common type of waves used for probing anisotropy of rocks in laboratory is the direct P wave. Information potential of the measured P-wave velocity, however, is limited. In rocks displaying weak triclinic anisotropy, the P-wave velocity depends just on 15 linear combinations of 21 elastic parameters, called the weak-anisotropy parameters. In strong triclinic anisotropy, the P-wave velocity depends on the whole set of 21 elastic parameters, but inversion for 6 of them is ill-conditioned and these parameters are retrieved with a low accuracy. Therefore, in order to retrieve the complete elastic tensor accurately, velocities of S waves must also be measured and inverted. For this purpose, we developed a lab facility which allows the P- and S-wave ultrasonic sounding of spherical rock samples in 132 directions distributes regularly over the sphere. The velocities are measured using a pair of P-wave sensors with the transmitter and receiver polarized along the radial direction and using two pairs of S-wave sensors with the transmitter and receiver polarized tangentially to the spherical sample in mutually perpendicular directions. We present an inversion method for elastic parameters describing general triclinic anisotropy. We demonstrate on synthetic tests that the inversion becomes more robust and stable if the S-wave velocities are included. This applies even to the case when the velocity of the S waves is measured in a limited number of directions and with a significantly lower accuracy than that of the P wave. Finally, we analyze velocities measured on a rock sample from the Outokumpu deep drill hole, Finland, including the error analysis for several levels of confining pressure.

Jan 1, 2015

By A Harding, M Chappell

Precast concrete segmental linings have enjoyed widespread use around the world, and are the lining type of choice for tunnels constructed using a shielded tunnel boring machine. However, there is significant variation in the design of such linings from one country to the next in such areas as materials, geometry, fixtures and fittings, waterproofing and reinforcement to name but a few. This arises because the speed at which the technology has developed within some countries and regions has sometimes outstripped the transfer of such technologies to the rest of the world.This paper provides some insights into the variations in lining design in different parts of the world with the aim of providing designers and constructors alike a reference for the different methods adopted. It provides a context for these developments by briefly summarising historical reviews of this subject before looking at some of the developments around the world over the last 15–20 years. The developments are presented with some reference to the reasons for implementation, and the advantages and limitations commented on. Following on from this description of the state-of-the-art, the authors also provide their own views on what developments we may see in this area in the near future.CITATION:Harding, A and Chappell, M, 2014. Precast concrete segmental tunnel linings – the state-of-the-art, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J Balzary, A Mohais

Dynamic market and operating conditions, coupled with an environment in which multiple objectives and trade-offs are common, pose major challenges for planners and schedulers working in any mining entity. Many mining companies recognise the need to shift from a siloed mining-focused push model to an integrated value chain, demand-driven approach, but there are still fundamental barriers in business process and the supporting technology preventing a consideration of end-to-end optimality.This paper presents some elements of experiences working with companies to adopt such advanced approaches. In addition to algorithmic elements, an approach to phased and gradual deployment of progressively more sophisticated optimisation models is described. From a practical software adoption perspective, it is believed that this last concern is also of primary importance. Next generation approaches to the optimisation of complex bulk commodity demand chains, namely iron ore and coal are presented, with case studies in the world’s largest integrated operations in Western Australia and Queensland from the raw material mined through to market. Utilising accurate simulation models supported by metaheuristic optimisation techniques, a range of ways to engineer a dynamic decision support framework that can adapt and change with the inevitable changes in commodity markets is explored. Objectives such as total revenue, margin, cost, NPV, throughput, asset utilisation, contractual penalties and bonuses, and energy consumption can be managed simultaneously across the mine, plant, logistics network, port operation, shipping and sales domains.CITATION:Balzary, J and Mohais, A, 2014. Consideration for multiobjective metaheuristic optimisation of large iron ore and coal supply chains, from resource to market, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 213–222 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Francis J. Quinn

The Natural Gas Act, of 1938, which put interstate pipelines under the jurisdiction of the Federal Power Commission, did not place a protective competitive shield around such companies - nor does any provision of the act guarantee them a profit. Natural-gas pipelines are competitive with each other and also with the coal and oil industries. Gas distributing companies must compete not only with the coal and oil industries, but also with the electric industry. Natural gas has captured markets from oil, which had taken them from coal. Oil men contend that gas prices have: been, held to an artifically low level by regulation. The electric industry is moving into the space-heating market, which pleases the coal people because the coal industry's largest customer since losing the railroads to dieselization has been the electric companies. The coal industry is attempting to monopolize the industrial and electric generating market through government intervention, and this is being done under the guise of concern for the national welfare through advocation of a "National Fuels Policy purporting to, further the cause of fuel conservation. Such a policy is contrary to American principles and would result in the individual's loss of freedom of choice and ultimately, in less reserves of preferred fuels because of diminished exploration efforts.

Jan 1, 1961

By C. S. Lord

"AbstractThe slow progress of conventional geological reconnaissance of the northern Canadian Shield during the past twenty years clearly indicates the need for a radically new field technique. Operation Keewatin, involving the use of helicopters as the traversing vehicles, was planned and executed by the Geological Survey of Canada in response to this requirement.About 57,000 square miles of District of Keewatin, N.W.T., were mapped during the 1952 field season in appropriate detail for publication at 1 inch to 8 miles. The Operation disclosed about 14,100 square miles of Precambrian sedimentary and volcanic rocks ranging in •age from Archaean to Late Proterozoic. About 7,700 square miles of this area are underlain by greenstone. This work was accomplished in a field season of 113 days, including the spring break-up. Routine aerial geological observations were made from two helicopters flying about 300 feet above the ground; these observations were checked by more than 1,700 landings and about an equal number of aerial observations from heights of less than 50 feet. Logistical support was •provided by a Norseman aircraft on skiis or floats. Combined helicopter and Norseman flying time was about 990 hours. More than 1-00 square miles were mapped per helicopter-hour, and about 815 square miles were examined each day that both helicopters operated. The reconnaissance cost about $207,000, or $3.63 per square mile mapped.As a result of this trial use of helicopters there is now available a reasonably proven method whereby an acceptable geological reconnaissance of the barren grounds of the Canadian .Shield within the Districts of Keewatin and Mackenzie might be completed within a decade. Thus, within a few years, it could place at the disposal of the prospecting and mining fraternity data which, by conventional methods, might not be made available to this generation. Due weight must be accorded this time factor when evaluating the aerial technique."

Jan 1, 1953

By H. E. Hilliard

The Bureau of Mines investigated hydrometallurgical procedures for concentrating precious metals from a mechanically processed metal fraction of obsolete military electronic scrap. Feed material for the leaching procedures described in this report was the high-tension-separated metal concentrate obtained as a fraction from mechanically processing partially stripped electronic units. Initial pretreatment with a 20-wt-pct-NaOH solution solubilized most of the aluminum. After washing, the resulting residue was incinerated to destroy any organics attached to metal particles. The incinerated residue was leached with 20-vol-pct H2S04 solution using two methods, countercurrent pressure and ultrasonic-aided leaching to solubilize the base metals, predominantly copper. Silver was recovered from the base metal leach residue using 50-vol-pct HN03, and gold contaminated with several percent palladium was recovered from the silver leach residue using aqua regia. The impure silver and gold plus palladium products represent about 1.5 wt pct of the high-tension-separated metal concentrate. Included is a three-step process evaluation study of mechanical processing of general electronic scrap and two hydrometallurgical procedures for leaching high-tension-separated metallic concentrates obtained from the mechanical processing step. Process evaluation concluded that only mechanical processing is economically viable.

Jan 1, 1985

By Z. R. Llanos

This paper presents a review of industrial and experimental processes for the recovery of molybdenum, vanadium, nickel, cobalt and aluminum from spent hydrotreating or hydrodesulfurization catalysts. Numerous processes have been developed in a laboratory and pilot scale. However, worldwide, there are only four well established commercial facilities currently in operation. The installed capacity of these facilities exceeds the availability of spent catalysts and may be sufficient to assimilate future increases of spent catalysts. Despite liability risks; significant quantities of spent catalysts are still being landfilled. Changing regulations that may affect the future handling and disposal of spent catalysts are also reviewed.

Jan 1, 1995

By J. Drelich

We report structural forces measured for 10 nm silica particles deposited on alumina substrate and 5-80 nm alumina particles on mica using atomic force microscopy technique. For nanoparticles forming clusters, oscillation of structural forces was recorded with a periodicity that is close to the size of the nanoparticles used. Additionally, selected force-separation results indicate that the forces involved between the AFM probe and individual nanoparticles can be studied using the nanoparticle-coated substrates.

Jan 1, 2006

By M. J. Steffens

ESPLIM is a novel separation technique that combines the advantages of solvent extraction and electrostatic dispersion but its application in the extraction of nickel by the direct solvent extraction route and the effect of high electrostatic field on the stability of organics have not been explored. These were investigated in this study and it was found that the technique allows 97% extraction of the nickel in a single stage compared with 3 stages by the conventional solvent extraction. Also, three months of exposure to 5.0 kV under simulated operational conditions had no adverse effect on the stability of organics.

Jan 1, 2005

By J. W. Breen

ASARCO Incorporated has upgraded or is in the process of upgrading the Galena mine electrical, pumping, refrigeration, compressed air, ventilation, hoisting and rockburst monitoring systems to allow continued mining and development work on the 1 589-m (5,200-ft.) level and to provide services for projected deeper mining and development. Additionally, a separate lead-silver milling circuit has been added to the silver-copper mill to process lead-silver ore reserves. This paper describes completed and planned improvements made to date on these systems.

Jan 1, 1991

By Thomas A. Phillips

This publication is an economic evaluation of the Bureau of Mines electrolytic process for recovering lead from scrap lead-acid batteries. In this process, scrap batteries are crushed and separated into metal and sludge fractions. The metal fraction is cast as anodes and electro- refined. Lead in the sludge fraction is converted to lead carbonate by reaction with an ammonium carbonate-ammonium bisulfite solution. The lead carbonate is then dissolved in a fluosilicic acid electrolyte from which pure lead metal is electrowon. A cost estimate is presented for a plant capable of processing 10,000 scrap batteries per day. The fixed capital cost for this plant is estimated to he $14 million on a fourth quarter 1984 basis. Operating costs are estimated to be $0.15/lb Pb recovered. Assuming a lead selling price of $0.17/lb, the interest rate of return on investment after taxes is 11 pct. A lead selling price of about $0.21/lb is needed to obtain a 20-pct-interest rate of return.

Jan 1, 1986

By Jeffrey M. Listak

This U.S. Bureau of Mines report describes the implications of in-mine ground control on the automated or remotely controlled operation of longwall mining equipment, Perhaps the greatest challenge to longwall automation researchers is the development of systems that will continuously function in the complex and unpredictable underground environment. The high degree of environmental variability, together with conditions brought about by the extraction process, makes complete automation of longwall mining a difficult task. The intellectual thought processes and split-second decision making required to avert disasters are lost when workers are removed from the face. As many mine operators can attest, minor problems, left unresolved, can eventually accumulate and lead to catastrophic consequences. The automation process will have to assess and manage various routine problems that are otherwise resolved through worker observation and experience.

Jan 1, 1990

By Meng Wang

"In this study, multiple methods that include geological surveying, laboratory studies, and numerical modeling have been used to study the deformation characteristics of a “deep inclined rock roadway with weak planes” (DIRRWP). Failure of the DIRRWP was found to be triggered initially by the shearing of the rock near the weak plane. The movement of the failed rock resulted in reduced confinement of the deeper rocks, and causing the failure of the supporting units and the severe deformation of the surrounding rocks. Hence, it is concluded that DIRRWP stability is affected predominantly by rocks near the weak plane. Corresponding control strategies for DIRRWP deformation were proposed: (1) greater support intensity is necessary to maintain the stability of the whole DIRRWP; (2) additional support is needed for rocks near the weak plane to reduce the potential of failure; (3) to increase the bearing capacity of the floor strata, as the floor needs to be supported; and (4) a supplementary support technique should be considered for cases of large deformation. The case study presented here indicates that the proposed control strategies can significantly reduce the potential of failure in rocks near the weak plane, thus preventing severe deformation of the DIRRWP.INTRODUCTIONAs shallow seams are mined out, the cover depths in most Chinese coalmines have become increasingly greater. Deep cover in a coalmine is considered to occur when the cover depth exceeds 800 m (Sun, Chen, and Miao, 2018). The loading and failure behavior of rocks in a deep cover setting are quite different from those in a shallow cover setting owing to the increase in in-situ stress, temperature, and hyperosmosis (Lobanova, 2008; Zhang et al., 2013). For instance, experience shows that bulking and dilating deformation in deep roadways is much greater than that which occurs in shallow roadways (Hou and Yang, 2018; Zhang et al., 2016). In addition, anisotropic behavior and thickness deviation of coal measure rocks, combined with the appearance of weak planes (e.g., faults, joints, and coal cleats) in coal and/or rocks, can significantly affect the stability of an underground roadway (Ghazvinian et al., 2013; Sun, Chen, and Miao, 2018). The presence of weak planes can significantly complicate displacement and stress transmission in nearby rocks. Additionally, tensile, compressive, and/or shearing failure in rocks near weak planes can be easily caused by high in-situ stresses in deep roadways; such failures may lead to further severe deformation of the surrounding rocks, resulting in roof falls and rib spalling (Kamata and Mashimo 2001; Wu, Ohnishi, and Nishiyama, 2004). A typical failure of the so-called “deep inclined rock roadway with weak planes” (DIRRWP) is shown in Figure 1. Severe deformation can be found near the weak plane. In this study, a plane or thin layer of rock/coal parting that can significantly reduce the strength of the surrounding rocks—and thus affect roadway stability—is defined as the weak plane."

Jan 1, 2019

By A. A. Brant

BECAUSE of its simplicity, the dip needle is widely used for locating magnetic rock formations in drift-covered areas. Although it responds only to strong magnetic disturbances, it has the advantage that surveys with it can be carried out rapidly, at relatively low cost, by untrained operators. More accurate surveys can be made with a much more sensitive instrument known as the magnetometer, but this must be operated by a specialist and the resulting survey costs are much higher. Mining men use the dip needle for the location of magnetic ores or mineral deposits associated with magnetic rocks. In certain districts, a survey with the dip needle may aid in solving geological structure. In the Little Long Lac and Crow River gold camps of Ontario, it has recently been used for these purposes. In interpreting the results of a dip needle survey, an understanding of the chief magnetic and mechanical factors determining the dip recorded by the needle is definitely necessary. For example, many observers locate a magnetic body by the highest dip values, apparently unaware that these frequently may not lie directly above the body. It should also be realized that a careful dip needle survey may yield information regarding the dip, breadth, and perhaps depth, of the magnetic body. Moreover, the observer should know when numerous closely-spaced dip readings are necessary, and when the dip may be measured at more widely separated intervals. The purpose of the following article is primarily to describe the factors affecting the registration of the dip needle, with a view to aiding investigators in a more accurate and complete interpretation of their results. To explain the cause of magnetic disturbances (anomalies) and the action of the dip needle, a knowledge of certain fundamental magnetic terms is necessary.

Jan 1, 1938

By Eduardo A. Pérez, Alejandro R. Alonso, Rosa María Luna-Sánchez, Gretchen T. Lapidus

Rare earth elements have been widely used in various sectors, from the aerospace and steel industries, to electronic applications, particularly in displays and batteries for portable devices. The high demand for newer and better equipment, such as cell phones, tablets and lap tops, has increased the consumption of the rare earth elements and at the same time the need for its recovery from electronic wastes. For that reason, the recycling of batteries is important, principally the Ni-HM batteries, due to their elevated content of rare earths elements, in addition to the high concentrations of cobalt and nickel. The current processes are based on dissolution in strong acid solutions (sulfuric acid concentrations from 2 to 4 mol/L), and temperatures from 30 to 90°C. In the present work, electrodes from spent Ni-HM batteries were leached using 1 mol/L H2SO4, in the presence of ozone as the oxidant, where recoveries of 96% for La, Ce and Nd were obtained at room temperature. The separation of Ni and Co from the leach solutions was performed using an electrochemical reactor, after which rare earth elements were precipitated, obtaining a mixture of its hydroxides with impurities below 1%, according to EDS analysis.

Jan 1, 2014

By John Paul Gries

During World War II, when the curtailment of imports led to an unprecedented demand for domestically produced mica, beryl, and other pegmatitic minerals, the Bureau of Mines and the Geological Survey entered upon a program designed to expedite the production of these minerals from the Black Hills area of South Dakota. The program involved mapping, sampling and drilling many pegmatite dikes found in the southern portion of the area and beneficiation tests in the field and in the Bureau of Mines laboratories at Rapid. City, S. Dak., Rolla, Mo., Salt Lake City, Utah, and College Park, Md. This paper describes the mode of occurrence and the sampling and beneficiation tests on one dike, the Helen Beryl pegmatite, which was investigated as part of the general pegmatite study in South Dakota. Investigation of the Helen Beryl Pegmatite by the Bureau began in August 1943 and was terminated in April 1944. During this period the Bureau took a series of bulk samples from pits for beneficiation tests, drove an adit through the center of the dike to obtain feed for a bulk-sampling plant operation, and finally drilled a series of long holes to sample the deposit further. Geologists of the Federal Geological Survey mapped the deposit and the faces of all excavations and logged drill holes from sludge samples recovered from long-hole drilling.

Jan 1, 1949

By Daniel B. Brimhall

The research presented here was initiated to investigate the role of atmospheric oxygen in the leaching of copper waste dumps. The problem of increasing the recovery rate of copper from these dumps is or great importance considering there are by conservative estimate in excess of fifteen billion pounds of copper located in dumps in the western United States. At this time, there is an increased interest in recovering copper from these dumps on a large scale. Large tonnages of low-grade material are being placed on the waste dumps of most copper mining operations in the western United States each day. The size of these dumps ranges from 5.5 million tons at Mineral Park, Arizona, to 4 billion tons at Kennecott's Utah operation (1). Leach solutions are recycled and contain ferrous and ferric sulfates. Large quantities of dissolved aluminum, magnesium and calcium salts may also be present. To this solution make up water is added to maintain the solution inventory and sulfuric acid is added for pH adjustment. Iron is introduced into the leach solution by the dissolution of the iron-containing sulfide and oxidized minerals present in the ore deposit. In addition to the iron from dump leaching, iron is also introduced during the precipitation process when the pregnant solution is passed over metallic scrap iron if cementation is used to reduce the copper in solution.

Jan 1, 1972

By Unknown

We are indebted to the Consolidated Mining and Smelting Company of Canada Limited for the several pictures in this issue showing the progress made in new construction at Tadanac and at Bonnington Falls, B.C. Plate No. 1 shows the down-stream side of the No. 1 hydro-electric station of the West Kootenay Power and Light Co. Limited at Bonnington Falls, on the Kootenay river, at which 17,500 k.v.a. will be developed to meet the requirements of the enlarged zinc and lead refineries at Tadanac. The generators, exciters and switch apparatus were supplied by the Canadian General Electric Company and the step-up transformers by the Canadian Westinghouse Company Limited. The plant throughout was designed, manufactured and erected by Canadians. Plate No. 2 shows the casting room of the new lead-plant and plate No. 3 the new tank-room of the electrolytic lead refinery at Tadanac. These additions will increase the capacity of the lead refinery by some 150 tons daily. The extensions also include practically doubling the zinc plant, and the gold and silver refineries. With the exception of the new stack, all designing construction and installation of the various plants is being done by the Company's own employees at Tadanac. Plate No. 4 shows the progress made in the construction of the new reinforced concrete stack at Tadanac. This stack, of 21 feet inside diameter at the top, will be brick lined and when completed will rise 400 feet above its foundations: the tallest of its kind in the world. The construction is in charge of the Rust Engineering Company of Pittsburgh, Pa. Plate No. 5 is a panorama of the Tadanac smelters and refineries. The photograph was taken from the roof of the lead smelter and gives an excellent idea of the size of the plant and its surroundings. Tadanac produces electrolytic lead, zinc and copper and fine gold and silver. During 1924 the company treated 1,333,523 tons of ore and produced: 161,400,- 769 pounds of lead; 92,197,824 pounds of zinc; l,382,750pounds of copper; 4,074,044 ounces of silver, and 26,976 ounces of gold.

Jan 1, 1925

By Z. G. Tao, Y. Y. Peng, W. L. Gong, M. C. He

"This paper presents an overview of the major landslide hazards in open pit mines in China, the currently used landslide control and monitoring techniques, and development of a new slope control technique incorporating the reinforcement, sliding force monitoring, remote sensing and forecasting in one system in order to constrain the displacement of the sliding blocks in the landslide to minimized the influenced area and provide precise warnings timely for the imminent landslides. For implementation of the new technique, a novel rock cable with large deformation and high resistance (also known as HE cable) was developed, which can elongate as long as 2m. At the same time, the necessary and sufficient condition for initiating a landslide and energy balance equations are formulated. Based on the proposed mathematical models and Beidou satellite system, the software and data transmission hardware for remote sensing and forecasting were developed the new landslide control technique has been applied successfully in 245 landslide sites in 12 provinces across China. In this article, two practical application cases in the open pit mines are reported.INTRODUCTIONChina is one of the countries in the world with the most widely distributed landslides and suffering the heaviest damage. According to the incomplete statistics, landslide hazards have caused death of hundreds of people and direct economic losses of several hundred million RMB each year. The landslide hazards have a great impact on the life and property safety of the people, safety of the infrastructure, as well as the social stability. Thus development of new techniques for forecasting and prediction of the landslides is imperative and of great importance. In general, the forecasting and prediction of the landslides consists of three major aspects, i.e. sliding time forecasting, landslide activity intensity forecasting and landslide hazard degree forecasting. Since a considerable part of the landslide-suspected area are adjacent to the residential areas or important infrastructures, development of the advanced landslide control and monitoring techniques to cope with the sliding time forecasting problem is more important.Over the past one hundred years, the most widely used slope monitoring techniques are based on displacement monitoring (Xu, et al. 2007; Toshitaka, 1998). In the early days owing to the limitation of the technology and equipment, the ground surface displacement and underground water level change were inspected mainly by man power for inferring the possibility of a landslide. In recent several decades, more and more ground surface displacement monitoring devices were brought to the market, such as the automatic total station, theodolite, digital level, borehole inclinometer and GPS based instruments, etc. Based on these modern techniques, some advanced instruments have been developed and applied to the landslide monitoring, for example, the “landslides early warning monitoring system” (Leonardo, et al. 2002), the “In-SAR” technique (Reevea, et al. 2000), the GPS and satellite geodetic survey based technique (Reevea, et al. 2000), and real-time telemetry technology (Xu, et al. 2007). These monitoring approaches have made significant contributions to the landslide disaster monitoring and forecasting. The major limitations for the ground surface displacement monitoring techniques are lie in the inconsistence between the displacement in ground surface and that in the sliding surface for the sliding mass, resulting in low degree of forecasting accuracy."

Jan 1, 2015