Search Documents

By K. V. Raj, T. Bhowmick

"Computational fluid dynamics (CFD) modeling of an open-pit mine has several challenges. A good quality mesh of the model domain is a pre-requisite for convergence in solution. Good quality tetrahedral meshing and insertion of prism layers in faceted open-pit mine geometry is complicated due to presence of numerous vertices and ridges. Presence of vertices and ridges result in poor quality tetra elements and holes in prism layers, which cause instability in the model. Good quality pit bottom prism mesh elements significantly improve the formation of velocity boundary layer and thermal boundary layer at the pit bottom. This results in an expected temperature dependent micrometeorological buoyancy flow in the pit. Whereas, model geometry without a prism layer, results in abrupt temperature gradient near pit bottom. Buoyancy flow and recirculation have significant effect in lifting mechanism of fugitive dust particles generated near pit bottom. Representative initial and boundary conditions and selection of appropriate turbulence model have significant influences on the simulation results. In this paper, three-dimensional models of open-pit mines are developed using commercial CFD software (CRADLE-CFD). Important constraints and various consequences in modeling complex open-pit geometries are presented. INTRODUCTION Application of Computational fluid dynamics (CFD) to model an open-pit mine to predict fugitive dust and pollutant concentrations in and around a mine is relatively new. In former Soviet republic (USSR), Baklanov [1] and Belousov [2, 3] presented numerical models of pollutant transport in open-pit mines in Arctic regions. In recent years, advances in mathematical and computational fields have enabled better modeling of pollutant dispersion phenomenon around mines using computational fluid dynamics (CFD). Several CFD software packages have been used by various researchers to model the pollutant transport in open-pit mines. Works by Alvarez et al. [4]; Lowndes et al. [5]; Silvester et al. [6]; Torno et al. [7]; Choudhury and Bandopadhyay [8]; Collingwood et al. [9]; Raj et al. [10] and Flores et al. [11]; are examples of application of various commercial and open source CFD packages (COMSOL, ANSYS, OpenFOAM) to model pollutant transport in open-pit mines. These researches provided a strong background for additional research involving CFD modeling of open-pit mines. Due to the limitations of computational times and capacity, 3D modeling and various aspects of fugitive dust dispersion in open-pit mines remained unexplored."

Jan 1, 2015

By David E. Hardt

"One of the critical variables to be controlled during arc welding is the size or geometry of the weld pool. The measurement of pool geometry has become an increasingly important problem with the advance of welding automation and control, and this paper addresses that problem. The basic concept of pool size estimation via measurement of pool dynamics is presented. The theory underlying this concept is discussed and is followed by a review of the current work in this area. It is concluded that pool dynamics can be characterized by natural frequencies of oscillation, for stationary welds, and that these can be measured by appropriate signal processing performed on the arc voltage. However, it appears that only full penetration welds show a strong correlation between weld size and natural frequency. Also, the extension of these results to the realistic case of moving welds has yet to be considered in detail. Nonetheless, this method of in-process measurement for real-time weld process control is still quite attractive where applicable since it can be accomplished simply by modifying the arc current schedule and by signal processing of the arc voltage.INTRODUCTUIONThe study of welding process control has been dominated by research into methods of in processing sensing of the weld pool geometry. While it has been shown feasible to measure the topside pool geometry using video methods [1,2], the penetration or backside bead width have remained elusive quantities. This is particularly true if a topside sensor location is required.The concept of using weld pool motion as a pool geometry sensing method was proposed by Hardt et al. [3] and later demonstrated by Hardt and Zacksenhouse [5] and Richardson and Renwick [6]. The concept is based on the fluid dynamics of a pool constrained by a solid container and by significant surface tension forces (i.e. a small shallow pool, not a ""pond"" or ""lake""). Such a pool, if subjected to external forces, will exhibit a surface motion is a function of that force, the properties of the fluid, the surface tension, and the shape of the container. Thus, if this motion can be excited and measured, and the relationship to the pool geometry determined, a means of sensing pool shape will exist."

Jan 1, 1986

By Mahmoud Sepehrmanesh, Verya Nasri, Maziar Partovi

"This paper presents an assessment of the impact of tunneling and its associated risks on pile foundations located in the influence zone of tunneling operation. Tunneling in proximity of pile foundations introduces deformations in piles and in turn induces additional axial and bending forces. In modern mechanized tunneling, ground convergence is controlled through balancing the earth pressure at the tunnel face as well as applying pressurized bentonite through the shield. Reducing ground deformation can consequently lower the additional deformations and forces developed in the pile foundation and lessen the associated construction risk. In this paper, comprehensive detailed finite element modeling was performed to quantify the effect of the different parameters on induced forces in piles. Finite element models took into account the nonlinear behavior of soil and pile-soil interface. The modeling results are of practical importance in risk evaluation of tunneling in vicinity of pile foundations. INTRODUCTION Tunneling operation in congested urban areas becomes more frequent as demand for further utilizing underground spaces grows. In urban settings, it is not uncommon for tunnel designers to plan a tunnel route in close proximity to other structures to satisfy other competing objectives like raising the alignment to reduce excavation volume. Setting the alignment close to existing structures increases the risk involved in the project. It is the responsibility of the designer to thoroughly identify, assess, and mitigate all design risks involved. In this paper, we focus on the aspects involved in tunnel construction in proximity to existing pile foundations. Tunnel operations introduce deformation in the soil mass. Consequently, a pile located within deformation zone experiences extra forces as a result of the imposed deformation. The developed forces and bending moments can be in orders comparable with the pile capacity depending on the relative horizontal proximity of the tunnel and the relative depth of tunnel with respect to the pile length."

Jan 1, 2016

By D. E. Severson

The coal solution refining process under investigation is basically a modi¬fication of the German Pott-Broche Process, on which patents date back to 1927, (5, 6). This process was used in Germany during World War II for the partial dissolution of coal in hydrocarbon solvent and removal of the ash by filtration to produce a raw material for carbon electrodes for aluminum plants. At the end of World War II the German synthetic fuel program, of which this process was a small part, was abandoned as not economical. In recent times the whole field of coal liquifaction has been given a new impetus; present technology indi¬cates that the economic processing and refining of coal may be possible in the United States. A number of approaches to coal liquifaction have been investigated, and several of these are currently being funded by the U. S. Office of Coal Research. One approach is direct thermal treatment of the coal as in the FMC Project COED, in which coal is thermally cracked to produce gas, liquid products and char. Another approach is the Hydrocarbon Research Institute's H-coal process in which coal is catalytically hydrogenated. Two other federally funded projects involve the extraction of coal by solvents. The Consolidation Coal Company's Project Gasoline, now in the pilot plant stage in Cresap, West Virginia, is an attempt to produce gasoline plus a residual char by partial solution of the coal substance. The coal de-ashing process being developed by the Pittsburgh and Midway Coal Company is a modification of the Pott-Broche process. Coal derived solvent is used with hydrogen to dissolve the entire coal substance, subsequent filtration removes the ash and the solvent is recovered for recycling.

Jan 1, 1968

By Qin-yong Ma, Jing-shuang Zhang, Bo Han, Pu Yuan

In order to improve the utilization rate of blasthole and blasting effect in vertical shafts, 5 kinds of millisecond blasting model tests with three circle vertical blastholes have been conducted in various delay times with concrete as model material. The blasting effects of millisecond blasting model tests are investigated from cutting volume, cutting depth, and blasting fragmentation, then a reasonable delay time is obtained. In the middle of concrete model, there are 4 blastholes uniformly distributed in the first circle, 6 blastholes uniformly distributed in the second circle, and 10 blastholes uniformly distributed in the third circle. Each blasthole is charged with one millisecond delay electric detonator, and the rest is blocked with stemming. The depth of blastholes in the first and second circle is 180mm, which is 20mm deeper than those in the third circle. After initiation, the blasting cavity is cleaned up, then the cutting volume and cutting depth are measured. Meanwhile, the blasting fragments are gathered and have analysed by function Rosin-Rammler. The test results show that when the inner two circle blastholes initiated simultaneously and the third circle blastholes initiated with millisecond delay, the reasonable delay time is 50 ms. At this time, the cutting volume and cutting depth of blasting model are 3920 cm3 and 68 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 53.2 mm and 74.6 mm respectively. While when all three circle blastholes initiated with millisecond delay, the reasonable delay time is also 50 ms. At this time, the cutting volume and cutting depth of blasting model are 10705 cm3 and 118 mm respectively. The fragmentation indexes of blasting fragments, X50 and X80, are 51.0 mm and 81.7 mm respectively. The researches indicate that for millisecond blasting with multiturn blastholes, the reasonable blasting scheme is multiturn blastholes initiated in millisecond delay and the reasonable delay time is 50 ms.

Jan 1, 2015

The Henderson Mine is a large underground panel cave molybdenum mine located near Empire, Colorado. Secondary blasting requirements have varied from one shot per 27 tonnes (30 tons) to one shot per 900 tonnes (1,000 tons) of ore. Geology, structure, cave abutment loads, and location of the ore in the column all affect the amount of oversize boulders (greater than three-fourths cubic meter or one cubic yard) that require secondary breakage. The primary method of breakage utilizes cone charges (plastic funnels filled with an emulsion) placed on accessible oversize rocks. Hangups in the brow area of the drawpoint are drilled with a self contained diesel hydraulic drill and loaded with gelatin dynamite. High hang-ups located beyond the reach of the secondary drill are "bombed" in with strategically placed emulsion bundles or ANFO bags loaded in place though a sectioned aluminum pipe.

Jan 1, 1994

By William H. White

"AbstractThe value of anomalous metal contents of trees as an aid to the discovery of mineral deposits was tested under field conditions cm four known ore deposits. Results indicate that a base-metal deposit, or any deposit containing zinc or copper, casts a 'metal shadow' into the overlying soil which remains approximately positioned above the deposit, regardless of the type of overburden or the movement of groundwater.The unusually high content of zinc or copper in trees growing within the limits of this 'metal shadow' constitutes an anomaly which can be detected and ,plotted in the field The field kit and certain points of the field technique are described briefly; and the characteristics of plant anomalies and possible limitations of their use are mentioned.IntroductionRecent investigations concerning the metal content of trees indicate not only wide variations in the metal content of different species and in different parts of the same tree but, in addition, suggest that the metal content of a tree is related to that of the subjacent bed-rock. Abnormal values found by Warren, Delavault, and others in trees growing above or near orebodies suggest a new tool which may prove of considerable value in exploration work. Evaluation of this new tool must involve consideration of the following questions:(I) Is the technique one which can be used under field conditions by persons not specially trained; and can results be duplicated within reasonable limits of error? Rather than taking tree samples for subsequent laboratory analysis, it is highly desirable that analyses be made on the spot. This allows anomalous results to be checked and additional samples may be taken at key points."

Jan 1, 1950

By Stephanie Trant

Montana Tech has been engaged in fundamental research on the processing of critical materials for more than a decade. Efforts include examining novel reagents for the flotation of Rare Earth Minerals (REMs). For this paper, research results on a collector, salicyl hydroxamic acid (SHA), are presented. Various REMs were examined and include the rare earth oxides (REOs), carbonates (RECs), and phosphates (REPs) of a suite of Rare Earth Elements (REEs). Differences are attributed to solution and surface chemistry, coordination number, and ionic diameter. SHA adsorption follows an ion-exchange process that leads to chemisorbed and surface-precipitated states, depending mostly on pH. Many effects are directly attributed to lanthanide contraction. Results should also be applicable to other REM/collector systems and further suggest that REM flotation should consider dual collectors.

By W. Basuki, B. Setyotomo, L. Hakim, R. Hendrajaya

Due to high crack sensitivity of slab product of gas and oil line pipe application, its steel making process and alloy composition were evaluated and then improved to overcome its critical solidification process and reduced surface defects. The study was conducted at Slab Steel Plant Krakatau Steel. The purpose was to improve slab surface quality by reducing surface defects so that the slab surface doesn't need to be totally repaired. The method applied was by performing plant trial process, which the secondary process parameters such as alloying method and the casting parameters such as casting powder selection, metallurgical cooling, mould level control, and superheat were continuously monitored and then adjusted to the surface quality of the product. Based on the calculation of Ferrite potential of the steel, the chemical composition was designed to achieve optimum casting parameters in order to avoid high shrinkage during solidification. The results of the study are decreased surface defect quantity, and smooth casting process. The quantity of crack decreased by almost 90%. The slab surface repairing was significantly reduced from 85. % to less than 10%. These new casting parameters and developed alloy composition are then used and standardized for the mass production of the steel.

Jan 1, 2005

By A. S. H. Kabir, I-H. Jung, J. Su, Yue. S., M. Sanjari

One of the major problems associated with conventional wrought magnesium alloys is the unwanted basal texture that forms during plastic deformation which generally does not change markedly after post-deformation annealing. Formation of precipitates on the recrystallized grain boundaries during annealing may affect the usual rotation of grains towards preferred basal direction resulting in texture weakening. In this study, Mg-Al-Sn alloy was hot compressed at 250°C and annealed at 350°C for various times. The initial as-deformed microstructure was partially dynamic recrystallized with dynamic precipitates on the grain boundaries. After annealing at 350°C, static recrystallization of the bimodal microstructure took place where at this temperature no static precipitates formed. The goal of this work was to study the effect of dynamic precipitation on the texture evolution during the annealing process. Texture evolution was studied during annealing by electron backscattered diffraction (EBSD) technique through a microstructure tracking process. It was found that precipitates on the recrystallized grain boundaries have significant effect on the usual rotation of the grains towards the basal direction, meaning significant texture weakening, which is beneficial for final mechanical properties.

Jan 1, 2015

By H. A. Pearse

Introduction This paper may be regarded as another instalment of the story of the Britannia milling operation. From time to time in the past, articles (1) have been prepared by various members of the staff, giving details of crushing, grinding, and flotation treatment for the normal Britannia ore. It is not, therefore, the purpose of the present paper further to discuss what may be termed the standard milling operation, but rather to describe a flotation practice which has been evolved directly as a result of the general depression. The normal Britannia ore mixture contains chalcopyrite and pyrite as the main sulphide minerals, together with minor gold and silver values. The standard milling practice, evolved during several years of experimentation, provided for bulk flotation of the two sulphides after primary grinding to only approximately 35-mesh, followed by regrinding of the bulk concentrate, with subsequent separation of the chalcopyrite and pyrite to make a marketable concentrate of each mineral. However, in the face of a constantly increasing surplus of copper on the world markets and a steadily falling price during 1930 and 1931, it was obviously undesirable to continue producing large quantities of this metal at a loss. On the other hand, Company officials were very reluctant to add to unemployment by closing down entirely, provided operations could be continued without excessive losses. Fortunately, the existence was known of a fair sized body of ore, quite low in copper and relatively high in zinc content, with also a very considerably higher gold value than that prevailing in other sections of the mine.

Jan 1, 1934

By S. R. Reddy

Thennodynamic properties of several quaternary systems are calculated using our recently modified Margules equations. The modified Margules equations are expressed up to infinite order in the vicinity of solvent. Quaternary system of one solvent and three,solute partials are derived. First order interaction coefficients of binary, ternary and cross -interaction parameters of quaternary system are used to'evaluate the partial functions. In the original fonn of Margules equations,derived partial functions are convergent and same 'as Unified ,Interaction Parameter Fonnalism. But considering up to infinite order of the Margules coefficients, the functions are divergent, in order to overcome this restriction, Margules equations are modified to get consistent equations. Derived partial functions are thennodynamica Hy consistent with Maxwell and Gibbs Duhem relations. The derived logarithmic activity coefficient of the solvent and solutes are consistent with the ternary systems. The calculated data, ie., activity coefficient values of nitrogen and interaction coefficients are in good agreement with the data of Fe-Cr-V -N. Fe-Ni-V -N, Fe-Cr-Ta-N and Fe-Ni-Ta-N systems.

Jan 1, 1999

By Mônica Suede Santos Silva

This work describes characterization of the performance of the tundish of a six strand continuous casting unit of the Companhia Siderúrgica Belgo Mineira, João Monlevade, Brazil using physical modeling. Permanent and transient conditions, due to ladle metal composition changes are considered. Pulse and step tracer addition techniques are employed to assess the control variables. For transient conditions the degree of inter-mixing and the minimum residence time are determined with a view to optimize the process especially during the grade changes of steel.

Jan 1, 2003

By Richard H. De Voto

The McDonald Gold Project and two satellite gold deposits near Lincoln, Montana, contain at least 9.9 million ounces of gold and 30 million ounces of silver. The McDonald gold deposit alone contains 7.2 million ounces of gold reserves that can be open-pit mined and processed by cyanide heap leaching at a projected cash operating cost of $190 per ounce. The deposit is predominantly oxidized with no chance of acid production, and can be mined, operated, and reclaimed with minimal permanent environmental disturbance other than the creation of an open pit filled with a fresh-water lake which would support trout. The Seven-Up Pete Joint Venture, the owner of the McDonald Gold Project, commenced permitting of an open-pit, heap-leach operation in November 1994. In 1998, Montana citizens passed an anti-cyanide, open-pit mining initiative, 1-137, which banned any new open-pit gold mine which uses cyanide processing, The Venture has conducted extensive studies, including metallurgical testing of the treatability of McDonald ores with alternative lixiviants, and has determined that all other mining and metallurgical treatment systems are vastly uneconomical in the recovery of gold and silver from the McDonald deposit. Therefore, the Venture's proposed open-pit mining and cyanide heap-leach processing is the only technology that can be applied economically to the McDonald deposit. Further, the analyses convincingly demonstrate that the proposed open-pit, cyanide heap leaching technology results in maximum resource conservation of this valuable and unique deposit and poses far less risk to human health and the environment than any of the alternative technologies.

Jan 1, 1998

By Gordon L. Draeseke

"Before getting into more specific aspects of my talk today I should put in one disclaimer - one week in Mainland China and one day with Premier Kosygin does not make me an expert on Sino-Soviet affairs nor on Canadian-Chinese relations. Perhaps though there is a message in the fact that one meeting took place in relative openness in China and the other was at least partly in a bullet-proof limousine in Canada. I thought it might be interesting and appropriate to explain something of the forest industry to you who are engaged in the mining industry. Our industry, like yours, is based on a natural resource and the basic activity that we engage in is the extraction and conversion of that resource into saleable materials. However, the fundamental difference between our industries is that our resource is on top of the ground - easily visible and easily measurable, whereas yours is under the ground - difficult to find and, having been found, expensive to measure. A second difference is that ours is renewable while yours is extractive, and you must keep finding more to keep up reserves."

Jan 1, 1971

By R. L. Grant

Study of the ignition of firedamp by explosives and the phenomena that underlie it is one of the long-term investigations of the Bureau of Mines. This report is the third in e series by the Explosives Branch summarizing the progress made at Bruceton in this study. The first paper described preliminary work on small, carefully controlled cannon shots the second discussed the results of suspended shots.5/ In this paper, experiments are described and interpreted that extend and support the concept of ignition presented previously. ACKNOWLEDGMENT The authors wish to thank Bernard Lewis, former chief, Explosives and Physical Sciences Division, and Guenther von Elbe, former chief, Physical Sciences Branch, Explosives and Physical Sciences Division, for their guidance and constructive interest.

Jan 1, 1954

By Gerald L. Finfinger

The Bureau of Mines conducted an experimental degasification project in Island Creek Coal Co.'s Virginia Pocahontas No. S mine. Methane from the overlying Pocahontas No. 4 coalbed was entering mine workings in the Pocahontas No. 3 coalbed through fractures in the roof rock. Small-diameter (l-S/B-inch) holes were drilled into the overlying coalbed to reduce the gas pressure and intercept methane flows, which were piped to the surface through an underground 6-inch-diam steel pipeline. The total methane flow rate from the vertical holes averaged 150,000 ft3/day for the first month. Methane flows into the mine were reduced by 47 pet, thereby demonstrating the effectiveness of this form of degasification in reducing ventilation requirements and providing a safer working environment.

Jan 1, 1979

Currently there exist several explosive quantity-distance (Q-D) rules variously exercised by most countries to protect personnel and property against the effects of accidental explosions. These regulations apply to manufacture, transport and storage of explosive products. This paper reviews the technical basis behind these regulations, as they apply to commercial and military explosives. The characteristics of a blast wave and missiles issuing out of an explosion site and their role in determining the level of damage to a target are discussed. The need for further research on the effect of detonation of charges of non-standard geometry, and under confined conditions such as tunnels is discussed. The challenge in estimating the net quantity of explosives involved and calculation of its TNT-equivalency is also highlighted.

Jan 1, 2011

By D. Satish Kumar, D. Mazumdar

"95% bulk mixing times in three different size water model ladles of a 140 T cylindrical shaped , dual plug ( located diametrically opposite at mid bath radius position) stirred, industrial ladle were determined experimentally with and without an upper buoyant phase. Based on dimensional analysis and a regression of the experimental data and, it was shown that in the inertial and gravitational force dominated flow regimes, 95% bulk mixing times for a slag-less situation can be described via:[equation]Parallel to this, a large number of experiments were also carried out in one of the water models (D=0.30m) to quantify the influence of an upper buoyant phase on mixing. These indicated that mixing time, operating variables and thermo-physical properties of the upper phase liquid can be correlated via a dimensionless relationship of the type:[equation]in which, Q is the ambient gas flow rate, L is the depth of liquid , (AL) is the slag layer thickness and 6 and t are respectively the surface tension and viscosity of the upper phase fluid The dimensional analysis, regression of experimental data as well as the adequacy of the proposed correlations are discussed in the text."

Jan 1, 2004

Laboratory testing by the Federal Bureau of Mines has shown that the removal of insoluble slimes using selective flocculation and flotation is a viable method for treating low-grade potash ores which have a high content of water-insoluble impurities. Results indicated that up to 85 percent of the insoluble slimes could be removed from sylvinite ore containing 5 percent water insolubles and 13 percent K20 using nonionic or cationic polyacrylamide flocculants and cationic, anionic, and/or nonionic collectors. Subsequent potash flotation recovered up to 88 percent of the potash in rougher concentrates containing 47 to 57 percent K20. Sizing and cleaner flotation of the rougher concentrates upgraded the products to 60 percent K20. Filtration of the insoluble slimes flotation concentrates recovered 87 to 0 percent of the brine. Flotation concentrate filtration rates were 7 times faster than the filtration rates of mechanically deslimed products.

Jan 1, 1977