Search Documents

By P Jonsén, S Larsson, M Parian, B I. Pålsson

The question of effective energy utilisation in grinding mills is not new. There are several conflicting arguments about tumbling mills, whether the efficiency is around 1 per cent or maybe 10 per cent, or even much lower. The energy not used is assumed to be lost as heating of the pulp, the grinding mill body, the charge, generation of shock waves and vibrations, etc. Stirred media mills on the other hand are generally considered to have better energy utilisation, but their energy efficiency is still not that clear. To shed some light on this a pilot-scale, wet stirred media mill was investigated over a range of operating conditions. The wet stirred media mill is a Drais PMH 5 TEX pearl mill fitted with an electric motor at 11 kW. It has been investigated over a range of operating conditions to try to balance the dissemination of the input energy in forms of the net grinding energy, mechanical energy losses, and the heating transferred to the pulp, the mill, the charge, and the cooling water. It is found that approximately 20–40 per cent of the input energy accounts for the grinding process. Also, that the difference between gross and net input electrical energy is mainly disseminated as heating of the pulp and cooling water. Mechanical energy losses appear to be much smaller than the heating effects. The use of a dispersant seems to mainly influence the heating effect.

Aug 24, 2022

By Daniel Willis, Ryan O’Connell

An 8-foot tall horseshoe adit tunnel located within an abutment of the Mount Morris Dam in Mount Morris, NY required repair of a failed reinforced concrete liner. The adit tunnel is entirely founded within highly weathered shale bedrock units, which induced unloading stress on the original tunnel liner. An epoxy-impregnated carbon fiber fabric wrap manufactured by Sika was chosen to repair the failed adit tunnel liner. Kilduff Underground Engineering completed the design of the tunnel repair utilizing both empirical and numerical methods. Merco Engineering Contractors completed the injection of chemical grout and repair liner installation.

Jun 23, 2024

By Alessandro Marques

Based on a short overview regarding steel defects in the final product, several refractory approaches to maintain or increase steel cleanliness are reviewed in this publication. By applying a ladle to mold approach, one potential to maintain cleanliness is to reduce the probability of air ingress by selection of a suitable slide gate system. Following this path, also the influence of a special configured impact pot is presented to maintain steel quality. Finally, higher productivity as well as cleanliness can be provided by selection of PROIL as a revolutionary product at the casting machine.

Oct 30, 2017

By Muhammad Azeem Raza, Samuel Frimpong

Underground mining environments are inherently hazardous and can lead to emergencies where effective rescue and self-escape become critical. Missouri University of Science and Technology is pioneering new technologies for effective self-escape. The rescuers and miners need to be trained in these new technologically driven environments. Previous research in fields like aviation, medical surgery, and oil and gas drilling has demonstrated the effectiveness of virtual simulation training, but the mining sector has yet to fully adopt advanced tools such as eye-tracking and immersive training modules. This research proposes a comprehensive training infrastructure incorporating these technologies to enhance situational awareness and decision-making during emergencies. The novelty lies in the application of advanced miner escape and communication technologies, specifically designed to monitor and enhance cognitive responses in high-stress situations. By leveraging these technologies, the proposed training infrastructure aims to prepare the next generation of underground miners and operators, by equipping them with the necessary skills to manage emergencies effectively.

Feb 1, 2025

By Dr. Kyle Perry, Ryan Sibley

Rock blasting is an inherently difficult field to quantify independent & dependent variables and the specifics of how the energy interacts with the material for a number of reasons. Independent variables such as geology are innumerable and stochastic, thus, on a laboratory and full-scale basis these variables are assumed to be homogenous across the desired rock boundary. Dependent variables are difficult to quantify in the laboratory based on the specific aspect of the fracture mechanisms that caused the fracturing. The same variables are difficult to quantify in the field because of the shear amount of material being blasted. The energy interactions with the material are difficult to quantify due to the rate of the reaction and the lack of quantification of independent variables. The second main issue with laboratory scaled rock blasting is the nature of the small form-factor explosives required for use in a scaled setting. These explosives that are utilized, traditionally PETN detonating cord, have a greater ratio of potential energy converted to shock energy rather than gas energy when compared to traditional field explosives, such as emulsion or ANFO. Research over the past decades has indicated that gas pressure has the greatest contribution to rock blasting performance, such as fragmentation and material throw. The factor of varying ratios of energy production has not been discussed in any of the reviewed publications. Publications discuss dimensionless scaling, dynamic similitude, and length-based scaling, however, none of these scaling methods discuss the ratio of energy production. The main focus will be correlation of energy production ratio of shock versus gas to dependent variables. This paper analyzes previous publications within rock blasting and related field as they pertain to scaling procedures and will highlight the similarities and differences in the various publications and detail the observed omitted variables that possibly lead to skewed data.

Jan 21, 2025

By Martin B. Hudson, Andrew K. Cho, Rolff B. Knobel, Les R. Chernauskas, Jonathan L. Ernst

ABSTRACT The Bruce Museum, located in Greenwich, Connecticut, is home to an extensive display of art and natural history exhibitions. A large addition was designed to be constructed adjacent to the museum requiring new spread footings to be installed up to 16.5 feet below the existing foundations. The soil conditions at the site consist of highly variable sand and gravel overlying weathered rock and sound bedrock. The Contract Documents called for traditional foundation underpinning. Traditional underpinning techniques, however, presented two major challenges on this Project; (1) deep underpinning pits would be required involving multiple levels and staging with tieback support and (2) the highly variable soil and bedrock composition and elevations presented uncertainty in the design and construction of the pits. In lieu of traditional underpinning, Geosciences Testing and Research, Inc. (GTR) proposed an “active” soil nail underpinning system. A major reason that the soil nail underpinning option was feasible, related to the fact that the soil nails and facing could be installed slightly in front of the existing footings rather than directly underneath the existing footings. The soil nail wall design involved one to four rows of soil nails with nail positions and wall depth able to be adjusted “on the fly” as excavation progressed depending on the field conditions encountered. To create the “active system,” the soil nails were pre-loaded to mitigate wall deformations that would be associated with a standard passive soil nail wall design. To evaluate the performance of the active soil nail wall and confirm design assumptions, an extensive automated monitoring, on-site testing and inspection program was proposed and executed by GTR to monitor deformations of the wall and the museum in real-time, evaluate and confirm bedrock and soil bond stresses and ensure that each soil nail was pre-loaded and locked off. Careful analysis, planning, and use of the observational method illustrates the importance of collaboration between design and construction personnel and applying engineering judgement throughout construction. The use of the observational method includes the potential for modifying design based on conditions observed. This paper presents a unique case study of the “active” soil nail underpinning system to support and protect sensitive structures, close collaboration between design and construction facilitated by real-time deformation monitoring, and its successful application as a safe and cost-effective alternative to traditional underpinning.

Oct 1, 2022

By Patrick Hansert

Safety was always in the focus of Badische Stahlwerke, however at the same time productivity has to increase as well in order to compete in a tough world market. In 2015 BSW produced over 2.2 Mio tons with two EAFs, leading to tap-to-tap times in average of under 40 minutes. Our philosophy has always been, that our most important success factor are the people: therefore we have to improve the working conditions as much as we can. Starting in 2012 Badische developed a robot that can support this goal. The first step was to use it for temp/sample taking, but the unit had to become a multi-tasker. Only 2 years later the first automated cartridge changer was installed at a customer site in Scandinavia, in late 2015 then the next tool was implement: tool changer allows now to use also a camera to check the condition inside of the heat after tapping. More tools are designed currently and will be implemented shortly. This paper describes the current installations and experiences as future applications.

Aug 17, 2017

This paper reviews recent advances in geophysical tools for mineral exploration. It does not restrict comments to methods which are usually applied in the tectonically active belt surrounding the Pacific Ocean, where geophysics has often been secondary to geological prospecting (eg visual recognition of surface alteration) and drainage geochemistry; but considers geophysical tools applied to a broader range of both deposits and terrains. For example, the subdued topography of much of Australia and Canada has lent itself to the development and extensive application of airborne methods. In Australia, deep weathering and transported cover have necessitated the use of geophysical methods to not only detect anomalies but also to map and understand basement geology. This same weathering has caused specific problems, particularly for electrical methods, but recent improvements in instrumentation, processing and visualisation have largely overcome them. A great deal of geophysical data is now being collected by government agencies, often from the air, and made readily available to explorers. In several Australian states it is free, often on line, and in almost all cases it is relatively cheap. These regional data sets are often augmented by more detailed local surveys in areas of interest. Although æanomaliesÆ are still important much more is being done with the high quality data which is now available The results are used for geological mapping, to test geological hypotheses, to construct detailed 3D geological models and, together with fluid flow modeling, to predict optimum locations for mineralisation.

Jan 1, 2004

By David R. Wilburn

The U.S. Bureau of Mines investigated the resources, costs, capacities, market relationships, and short-and long-term supply of bauxite, alumina, and aluminum. The 45 evaluated mines and deposits in 14 market economy countries (MEC's) have a demonstrated resource of 8.4 billion mt of bauxite and an aluminum content of approximately 2.1 billion mt. Developed world bauxite resources and existing primary aluminum smelting and refining capacity are sufficient to satisfy demand through at least 1995, when additional properties (with higher cost levels) would need to be developed to satisfy future demand levels. It is anticipated that new alumina or aluminum production most likely would occur in developing regions with large bauxite potential, low-cost energy sources, and a close proximity to refining and/or smelting capacity. An increase in aluminum recycling capacity would help meet future demand increases. A series of network model supply analyses was performed for the period 1988 through 2000. Based on announced future production levels and assuming demand grows at the level outlined in the analyses, model results indicate there is sufficient material available to meet demand until 1998, where-upon an aluminum shortfall is projected. Additional analyses investigated the effect of a reduced growth rate of demand and regional production variations in Venezuela on the international aluminum industry.

Jan 1, 1993

By Dennis R. Kasper

This study evaluates selective environmental impacts of two distinct in situ mining techniques. In situ leaching of uranium, porphyry copper and native copper and in situ borehole (slurry) mining of uranium, sandstone, and pebble phosphate ores are the techniques and minerals investigated. The potential impacts onsite in the desert southwest (porphyry copper), Michigan (native copper), Texas and Wyoming (uranium), and Florida and North Carolina (phosphate) are addressed and discussed. The study emphasizes those impacts which are unique to in situ solution leaching and borehole slurry mining. Impacts which are characteristic of all construction projects in the general geographical areas investigated, such as socioeconomic effects on surrounding communities and site-specific impacts, such as rare and endangered species, are beyond the scope of this study. For each of the in situ processes and associated ores investigated, the physical and chemical characteristics of the systems are described, the toxicity of the leaching solutions are presented, and the potential impacts on the environment are developed.

Jan 1, 1979

The U.S. Bureau of Mines, Department of Labor, and United States National Committee of the CIE hosted the TC4.10 Mine Lighting Committee Meeting and Second International CIE Mine Lighting conference at the MSHA Academy in Beckley, WV from October 12-16, 1981. This was the first time the meeting and conference had been held in the United States. The TC4.10 Mine Lighting Committee, chaired by Dr. Adam Peretiatkowicz of Poland, was attended by 15 committee members and six guests representing eight countries. Discussion during the meeting covered mine lighting instrumentation, open cast (surface mine) lighting, and lighting sources. The committee also reviewed a draft of proposed lighting terminology and suggested changes to make the definitions more acceptable to representatives of the nations present. The mine-lighting conference featured 20 papers presented by 18 speakers representing six countries. The papers covered all phases of mine lighting, including research, hardware development and application, personnel acceptance, and requirements for system maintenance. The conference attracted 126 attendees and also included displays by eight lighting hardware manufacturers and four mining machine manufacturers. Papers from the conference are being published by the Government Printing office, with copies presented to the conference attendees. Copies will be available to others interested through the NTIS. During the course of the TC4.10 meetings and conference, committee members toured three mining equipment assembly plants, and six of the foreign representatives visited a longwall installation in an underground mine. Planning and administrative services for the meeting and conference were handled by Bituminous Coal Research, Inc., under USBM Contract H0318038.

Jan 1, 1982

By G. S. Beaumont

This report presents a programme of work to demonstrate the use of a surface-based centralised computer control system for the remote monitoring and control of underground conveyors in a US coal mine. The system selected for demonstration was the 'Dynalink' Micro MINOS system which is manufactured by Hawker Siddeley Dynamics Engineering Limited. The site selected was Barnes S Tucker Lancashire No. 20 Mine located near Carrolltown, Cambria County, Pennsylvania. The system concept, operating and application software was designed and developed by the. British National Coal Board. The report describes the selection of the site, specification of the system requirements, commissioning, operation and evaluation of the system under typical US mine operating conditions. Experience with the system, based primarily on the system reliability and performance of conveyor control, was favourable. Mine management personnel felt that the system had successfully achieved its objectives and were keen to expand monitoring and control to other activities.

Jan 1, 1986

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

"The National Institute for Occupational Safety and Health (NIOSH) has recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with medium-sized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in this study: a 15.2-cm (6-in.) wide shelf; a 7.6-cm (3-in.) wide shelf; and a 7.6-cm (3-in.) wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1, and 1:1 were evaluated for the 15.2-cm (6-in.) wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust-collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. The simulation results could be used for future development of dust control methods, particularly to address respirable silica dust, for a surface mine blasthole drill shroud.INTRODUCTION Surface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1% of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples) • 5.8% of rotary drillers were overexposed to respirable silica dust (9 out of 155 samples) • 7.3% of drill helpers were overexposed to respirable silica dust (3 out of 41 samples) • 7.5% of blaster/shotfirer were overexposed to respirable silica dust (3 out of 40 samples) Of significant interest is an x-ray surveillance study recently completed under the NIOSH Enhanced Coal Workers’ Health Surveillance Program (ECWHSP). This program offered free chest radiographs to surface coal miners in 16 states. Pneumoconiosis was found among 2.0% of the 2,328 screened miners with at least 1 year of mining tenure. Twelve miners had radiographic changes consistent with progressive massive fibrosis, and 9 of these 12 miners reported no underground mining tenure. All but 1 of the 9 miners worked at occupations that were in the vicinity of blasthole drilling, either as a driller, blaster, or blast crew member [1]."

Jan 1, 2018

By Donna Guillen, Matthew Lehar, Sebastian Freund, Jennifer Jackson, Helge Klockow

"Research and development is currently underway to design an Organic Rankine Cycle (ORC) system with the evaporator placed directly in the hot exhaust stream produced by a gas turbine (GT). ORCs can be used to generate electricity from heat that would otherwise be wasted, thus producing carbon-free energy. In conventional ORC configurations, an intermediate oil loop is used to separate the hot gas from the flammable working fluid. The goal of this research effort is to improve cycle efficiency and cost by eliminating the pumps, heat exchangers and all other added cost and complexity of the additional heat transfer loop by developing an evaporator that resides in the waste heat stream. Direct evaporation – although simpler and less expensive to implement than indirect evaporation of the working fluid – has historically been avoided due to a number of technical challenges imposed by the limitations of the working fluid. The high temperature of the hot exhaust gas may cause decomposition of the organic working fluid and safety is a major concern due to the high flammability of some of these working fluids. The research team has addressed these challenges and developed a new direct evaporator design that can reduce the ORC system cost by up to 15%, enabling the rapid adoption of ORCs for waste heat recovery. The ORC system is intended to integrate with the GT either as a retrofit or to be marketed as a single package, thus maintaining the manufacturer’s warranty.IntroductionWaste heat from turbines and engines used in industrial applications along with waste heat from industrial processes are exceptionally abundant sources of energy. If even a fraction of this waste heat could be economically converted to useful electricity, it would have a tangible and very positive impact on the economic health, energy consumption, and carbon emissions in the U.S. manufacturing sector. Land-based gas turbines are used in a broad range of applications to produce both shaft and electrical power. Most commonly known for generating electricity either as peaking units or as base load units, they are also used to directly drive pumps, compressors or other machinery requiring shaft power. Simple cycle gas turbines have the advantage of a short startup time relative to coal-fired and nuclear units, however, they incur a significant penalty on their efficiency. Large frame gas turbines usually are combined with bottoming steam-based Rankine cycles to increase the overall efficiency of the system and thereby improve their cost performance. Small-frame gas turbines with exhaust temperatures around 500°C could in principle benefit from steam bottoming cycles, but rarely use them in practice because of the high capital cost of the steam system. Particularly for base load small frame gas turbines, akin to those used in pipeline applications, an increase in efficiency is highly desirable."

Jan 1, 2011

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

The National Institute for Occupational Safety and Health (NIOSH) has recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with medium-sized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in this study: a 15.2-cm (6-in.) wide shelf; a 7.6-cm (3-in.) wide shelf; and a 7.6-cm (3-in.) wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1, and 1:1 were evaluated for the 15.2-cm (6-in.) wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust-collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. The simulation results could be used for future development of dust control methods, particularly to address respirable silica dust, for a surface mine blasthole drill shroud. INTRODUCTION Surface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1% of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples) • 5.8% of rotary drillers were overexposed to respirable silica dust (9 out of 155 samples) • 7.3% of drill helpers were overexposed to respirable silica dust (3 out of 41 samples) • 7.5% of blaster/shotfirer were overexposed to respirable silica dust (3 out of 40 samples) Of significant interest is an x-ray surveillance study recently completed under the NIOSH Enhanced Coal Workers’ Health Surveillance Program (ECWHSP). This program offered free chest radiographs to surface coal miners in 16 states. Pneumoconiosis was found among 2.0% of the 2,328 screened miners with at least 1 year of mining tenure. Twelve miners had radiographic changes consistent with progressive massive fibrosis, and 9 of these 12 miners reported no underground mining tenure. All but 1 of the 9 miners worked at occupations that were in the vicinity of blasthole drilling, either as a driller, blaster, or blast crew member [1].

Jan 1, 2019

By A. Kotze, D. Messina, E. Nagels, Y. Cryns, S. Arnout

The FlashPhos process aims to recover white phosphorus (P4) from sewage sludge by drying, flash combustion/gasification, and carbothermic refining steps. This study evaluates the material behaviour of sewage sludge ash melting and reduction in a refining furnace for the novel FlashPhos process. Thermodynamic modelling in FactSage 8.2 is combined with experiments from a tube furnace to determine the possible phosphorus recovery and minor element behaviour. For the two studied sludges, a yield of 40% and 75% white phosphorus is achieved after 1 hour at 1600°C, corresponding with a 60% and 25% loss to the metal phase. This is slightly above the calculated equilibrium yield of 28%–73%, which depends mainly on the Fe/P ratio of the sludge. Temperature is found to have a significant influence on the final phosphorus yield when leading to incomplete melting of the ash. A clean slag is produced in the process free of heavy metals making it suitable to be used as a cement-like binder material. The main heavy metals that co-evaporate with the phosphorus are Zn, Pb, As, Sb, and Sn. Additional processing steps will be required to remove these to produce a pure P4 product. The metal alloy consists of mostly Fe and P with smaller amounts of other components such as Mo, Cr, Cu, Mn, Sn, Sb, and V. The final slag consists of CaO, SiO2, MgO, and Al2O3 with virtually complete removal of P and heavy metals.

Oct 2, 2025

By P. R. Smith, R. A. Walters

Borates have been mined in the desert areas of California and Nevada for more than 100 years. To about 1890, playa surface mining provided the chief sources of boron minerals. Underground mining of colemanite and later of borax and kernite was predominate until about twenty years ago. Open pit mining of the large deposits of borax and kernite near Boron, California has been most significant for the past twenty years. Mining of colemanite in the Ryan, California area, near Death Valley, began in 1907. Following the discovery of the large deposits in the Boron area (about 1957), mining in the Death Valley area became nearly nonexistent. Only small tonnages were mined for special uses. Little mining was done in the Boraxo area near Ryan. The first claim was made in about 1915. In 1960 the area became the property of the Kern County Land Company, which was acquired by Tenneco Oil Company in 1967. In 1976 the various boiate properties and claims in this region were acquired by American Borate Corporation. The open pit mine is now approximately 122 m (400 ft) deep, 910 m (3000 ft) long and 305 m (1000 ft wide). The borates in the Boraxo pit consist primarily of three minerals. These are about 50% colemanite (CB6011 5H20), about 40% probertite (NaCaB50g 5H20), and 10% ulexite (NaCaBgOg 5H20). The colemanite, along with boric acid and high-grade colemanite ore from Turkey provide the only sodium-free borates for production of textile grade fiberglas. When heated to its decomposition temperature, colemanite decrepitates to a fine powder, which is the basis for the concentration process. The gangue minerals in this deposit are primarily calcite and clays, including bentonite. The ore body has a very low arsenic content, which is a desirable feature. Test work had been done with samples prior to the results discussed herein. This paper will discuss results of test work which were the basis for erection of a plant, and the subsequent plant operations. Laboratory Calcination and Air Tabling Tests Laboratory calcination tests showed that substantial upgrading of the borate could be accomplished by calcining followed by screening of the calcined material. Removal of the + 28 mesh calcine resulted in borate losses of less than 10% with a rejection of 40 weight % or more of the calcine. The minus 65 mesh calcine generally met the requirement of containing 48%, or more, B203. The minus 28 plus 65 mesh material contained an intermediate quantity of borate and would require additional treatment. Testing demonstrated that ore would not have to be reduced to a size finer than 19 mm (3/4 in.) prior to calcination. A temperature range from 400 to 455OC (750 to 850°F) was apparently satisfactory. Calcination at a temperature of 48Z°C (900°F), or higher, was unsatisfactory due to fusion. All laboratory calcination tests were static tests conducted by placing small covered charges in a laboratory furnace for 40 min. In all tests vapor issues from the furnace for 5 to 7 min. Following this period the ore could be heard "popping," due to decrepitation of the colemanite. The reaction generally continued for approximately one-half hour. Various size fractions of the calcination products from laboratory tests were subjected to laboratory air tabling tests, usually after removing the plus 28 mesh material. Laboratory air tabling tests were conducted employing a Whippet V-80 model air table manufactured by Sutton, Steele and Steele Co. now known as Tripple S Dynamics. Variables include both end and side-tilt, speed of vibration, and quantity of air rising through the deck. In addition to the variables in the machine itself, the feed rate is also a rather critical variable. Testing demonstrated that all - 28 mesh size fractions of the calcine could be successfully concentrated to 48% F2O3 or greater. For the finer material recoveries into the concentrate were between 85 and 90% of the borate. With the coarser material a substantial amount of middling was produced which required cleaner tabling. Laboratory calcination and air tabling tests indicated a process whereby the borate could be concentrated to about 50% B203 with borate recoveries approaching 90%. Moreover, the iron content of the concentrate was well below the required specification of 0.3% Fe2O3. Pilot Plant Calcination Following the laboratory test work described above, pilot plant testing was conducted to prove the process, provide data for engineering studies, and provide product for a prospective purchaser. The kiln used was 0.9 m-diam (3 ft) by 9.0 m (30 ft) long and had a belly section 1.2 m-diam (4 ft) by 2.74 m (9 ft) long near the discharge end. The kiln was operated at a speed of 0.7 rpm. Gas was fired into the kiln at an average rate of 27.1 m3/hr (958.4 cu ft per hr). The air to gas ratio used was 10:1. The ore was fed to the kiln countercurrent to the flame and discharged through a hopper into a screw conveyor which discharged to a 1.2 m (48 in.) Sweco separator. The separator had 28, 65, and 150 mesh screen cloths, with the plus 28 mesh fraction being discarded. The minus 28 mesh fractions were later subjected to air tabling. The exit gases, containing some calcine dust, were swept through two cyclones to recover the dust. The gases then were scrubbed in a Ducon scrubber; very little dust reported past the first cyclone. The dust from the first cyclone was also saved in drums. In addition to the gas rate, the flue gas velocity, after

Jan 1, 1981

By B. Samanta, S. Bandopadhyay

Ore grade modeling of a placer gold deposit is considered a challenging problem even today. Typically, gold-bearing deposits show extremely erratic and unpredictable grade variation. This is principally because of isolated occurrences of gold metal within a few high-grade pockets. Because of sporadic fluctuation of high-gold-grade distribution, the overall spatial continuity of the deposit becomes poor. This type of variation is often described by a lognormal or highly skewed frequency distribution, and the spatial continuity of the deposit is characteristically represented by a variogram model that exhibits a high nugget component. Further complicating the matter is the sparse availability of drillholes to capture such erratic variation. Due to the prohibitive cost of drilling, gold grade and reserve estimations are typically carried out using insufficient exploratory data. Use of a traditional estimation technique on limited data often produces an unreliable ore grade model. Kriging and its nonlinear variation, lognormal kriging, are frequently used in gold deposit modeling (Rendu, 1979; Journel, 1980); however, kriging is flawed by the smoothing effect. Moreover, though kriging is known to be globally unbiased, it is not free from conditional bias. As a result, if a deposit is modeled using the traditional kriging technique, a high-grade zone can be predicted to be a low-grade zone and vice versa. Predicting high grade as low grade results in a missed opportunity to exploit profitable ore. On the other hand, prediction of low-grade ore as high-grade ore might result in financial loss for a mining operation. Thus, the use of kriging for ore grade mapping of a gold deposit may not be recommended. Estimation techniques (including kriging) can produce an estimate with minimum error in a minimum-error variance sense. However, no matter which estimation technique is used for grade modeling of a highly erratic deposit like gold, the error margin is bound to be high. Therefore, any grade prediction made for an unknown location is associated with high uncertainty. Since various mine-planning operations, including derivation of grade tonnage curve, pit design and economic analysis of the deposit, are based on estimated grade rather than true grade, a mining project evaluation that depends upon estimation will be subject to considerable risk. Thus, the successful design of a mining project not only depends upon accurate grade estimates, but also upon accurate assessment of uncertainty, for predictive grade is equally important. Although the kriging standard deviation is used as an indicator of uncertainty for prediction, it is flawed by characteristics related to a data-independence property. This study, therefore, investigates the stochastic simulation technique of conditional simulation for ore grade modeling of a placer gold deposit at Nome, Alaska. It is expected that the research will provide a better solution to ore-grade deposit modeling than the kriging technique because (1) conditional simulation preserves spatial continuity as well as reproduces the data histogram, thus avoiding the smoothing problem; and (2) generation of multiple realizations helps to accurately quantify the uncertainty about grade values in the deposit.

Jan 1, 2009

By Charles V. Riley

While the late 1960's are known as the years of the public recognition of impending environmental crises, the 1970's will be known as the decade of public concern for improving the quality of that environment. One of the present major environmental concerns is the temporary disturbance resulting from coal surface or open cast mining. To realize that this concern will continue in the future, one need only observe the daily news media. Increasing energy demands in the U.S., a doubling of electrical power consumption each decade during the present century, and the projected needs for the remainder of the century are indica¬tions that coal surface mining as a major extractive industry will continue. Coal and lignite, prime energy resources and extremely abundant in these United States, in the face of seemingly limited gas, oil and uranium reserves, are both destined for expanded future use. Presently some extremely serious techno-logical and environmental problems are associated with the develop¬ment and use of nuclear power. It is true that the extraction and use of coal as an energy fuel poses disruptive problems for the environment, but the solutions to many of the problems are known or can be solved within a reasonable time framework. Certainly our national well-being and continued survival, as a free nation within the world community, automatically dictate the continued use of the coal resource for energy. Concurrently, those engaged in coal surface mining, with the temporary disturbance of the land and water resources, must also realistically conclude that public concern for maintaining and improving the quality of the environment will not diminish. Although as ecological, economic, social and aesthetic elements

Jan 1, 1972

By P. Leeuw, H. Mtegha

"The aim of this paper is to enhance the understanding of the nature of mining input technologies in the South African mining industry. In the context of this research, mining inputs refer to input technology into the activities in mining engineering fields, which include mining-related production activities, rock engineering, mine ventilation, and mine transportation (handling of personnel, material, broken rock, and pumping). Input technologies in supporting fields such as geology, other engineering disciplines, human resource, procurement, finance, as well as downstream fields that include metallurgy, and marketing of minerals, were disregarded.The mining input technologies were divided into 12 nodes, and data from a sample of 150 first-tier mining suppliers was analysed. It was found that, in general, there is a high local content in mining input technologies, particularly as regards technical support services, artefacts, and machine technologies. This points to the presence of mining-induced backward linkages in the South African mining industry. The majority (83%) of companies that provide input technologies into mining are located in Gauteng Province, and relatively few are found in provinces where mining is concentrated such as North-West, Limpopo, Mpumalanga, and Free State. IntroductionSouth Africa is well endowed with minerals, with more than fifty different minerals being mined throughout the country. For this and other reasons, mining is one of the crucial pillars in the South African economy and its importance is well documented (Robinson and von Below, 1990; Creamer, 2010; Department of Mineral Resources, 2015). In 2013, South Africa was the largest global producer of chromium, ferrochrome, platinum group metals (PGMs), and vermiculite and the second largest global producer of antimony, manganese, titanium, and vanadium (Chamber of Mines of South Africa, 2014). In 2013, the mining industry contributed 6.7% to South Africa’s GDP and was the fifth largest sector in the economy, as shown in Figure 1."

Jan 1, 2016