Search Documents

By Michael Gebman, Jack Gerwick

"With the opening of the new San Francisco-Oakland Bay Bridge East Span, the former bridge and its caisson foundations are being demolished. Caisson foundations are in the path of a future shipping channel and therefore need removal down to the mudline 50 ft below water (MLLW). For the first caisson to be removed (E3) a mechanical demolition was performed above the waterline and an implosion was done for the remaining caisson down to mudline. Mechanical demolition consisted of excavators operating from either on top of the caisson, from work platforms or from barges. The demolition was implemented on a trial basis with a successful implosion on November 14, 2015. The work was conducted in an environmentally sensitive area, with measures taken to protect fish, marine mammals and birds. This demolition technique was cost effective, faster to execute, and had a better environmental impact then an alternative option. The demolition, measures implemented to protect the environment, outcome, and lessons learned are presented.INTRODUCTIONThe California Department of Transportation needed a cost effective and environmentally friendly solution for removal of the remaining San Francisco-Oakland Bay Bridge (former East Span) caisson foundations, starting with caisson E3. This was necessary to clear a future shipping channel. One option was to construct a steel cofferdam around the caisson to allow demolition in the dry down to the mudline. This option would take years to complete, be cost prohibitive, and its noise would disrupt aquatic life and birds throughout the cofferdam construction and demolition. An alternative option was implemented on a trial basis to conduct a mechanical demolition of the caisson above waterline along with an implosion of the remaining caisson down to mudline. This had the clear advantage as a cofferdam was not needed, and the demolition project duration would be approximately 6 months, instead of several years for the cofferdam option. The potential impact on aquatic life and birds from the implosion was a concern, as the location is environmentally sensitive; however, measures were implemented to minimize these impacts. As presented in this paper, this demolition option was implemented on a trial basis for Caisson E3. The technique succeeded and will now be used on the remaining caissons.BACKGROUND INFO ON CAISSON E3The reinforced concrete Caisson E3 is the largest caisson which supported the former East Span of the Bay Bridge. It was constructed in 1934, with the Bay Bridge opening in 1936. Figure 1 shows the project location. The caisson had a cell arrangement of 7 x 2 above the mudline. Below mudline, the caisson had a cell arrangement of 9 x 4. A structural transition was made between the 7 x 2 and 9 x 4 cell arrangements with buttress walls. All cells were flooded, as underwater openings were included in the original caisson walls to equalize the hydrostatic pressure. Figure 2 shows the caisson layout with limits for mechanical demolition and for the implosion."

Jan 1, 2016

By Allen D. Look, Norman King

For many years, much thought and effort have been devoted to the achievement of safety in the use of explosives by those interested in the preservation of human life and the protection of property. As a result, we now have adequate rules pertaining to the safe use of explosives , which, if observed, would prevent many, perhaps ail , of the explosives accidents that yet occur . Although the rules respecting the use of explosives are believed to be well - known, many accidents occur because they are disregarded . The mental awareness aroused by a tragic accident usually will cause safety precautions to be taken for a while ; however , this awareness gradually disappears unless a sincere effort is made permanently to prevent similar accidents . Frequently, because safe methods are more irksome than unsafe methods , the lessons taught by accident experience are forgotten in a short time , vigilance is relaxed , and there is a gradual return to unsafe , easy methods of performing work. If the preservation of human life is important , the unfortunate experiences of others and the lessons taught by them should be applied to reduce unnecessary loss of life . The value of a life lost as the resuit of accident should be calculated not only from the monetary and humanitarian standpoint but also according to what the accident could contribute in the way of saving other lives and suffering . This saving of other lives can and will , if the lessons from unfortunate accidents are applied , convert a loss to a gain a gain of such magnitude that the accident victim could be considered

May 1, 1944

By J. Petersen, H. Naderi, M. H. Nikzad, M. Karimi

In this research, the thermodynamic study of sodium persulfate (Na2S2O8) solution in the presence and absence of H2SO4 and Fe3(SO4)3 was done. Eh-pH and equilibrium distribution diagrams were constructed using Outotec HSC Chemistry Software and the main stable ionic species were determined. Also, the mean activity coefficient and Pitzer model coefficients were evaluated. Effects of system composition, sodium persulfate concentration and temperature were investigated. According to the results, HS2O7 -, HS2O8 -, S5O3 2-, S4O3 2-, S3O3 2-, HS- and NaSO4 - are the main stable species in these three systems. Increasing of sodium persulfate concentration resulted in disappearing of SO4 2- and the appearance of NaSO4 -. The main effect of increasing the temperature from 25 to 75oC, is changing the stability regions of HS2O7 -, NaSO4 -, SO4 2- and S2-. From equilibrium studies, it was concluded that at 25 and 50oC, increasing the persulfate concentration results in a 55-60% decrease for HS2O7 - and an 20- 30% increase for HS2O8 -. At 75oC, HS2O8 - becomes the main species and its percentage decreases with increasing the persulfate concentration. Keywords: Thermodynamic, sodium persulfate, activity coefficient

Jan 1, 2020

By S. Mohanty, K. Sarangi, S. Dash, P. P. Patra

Industrial effluent from various industries contains heavy metals that are a serious threat to humans, flora and fauna in water bodies, and the environment. The heavy metals are dumped after precipitation, which has serious environmental consequences. In this paper, a 2D axi-symmetry CFD model has been developed to study the extraction of chromium ion from industrial effluent, in a hollow fibre membrane, using Alamine 336 as the carrier and kerosene as the diluent. The Navier Stokes equation was used to predict the velocity profile of the aqueous and organic phases, and species transport equation, which considers both convective and diffusive mass transfer, was used to predict the concentration profile of the chromium ion in the computational domain. The distribution coefficient was experimentally determined at a pH 4, which was found to be the optimum pH. Numerical simulations were performed considering 11.11 mol/m3 of initial feed concentration for chromium ions and extractant concentration of 0.2 M. Simulations were carried out with various aqueous and organic flow rates, and validated with experimental data. Keywords: CFD, metal extraction, hollow fibre membrane, heavy metals

Jan 1, 2020

By Forrester P. I, Richardson W

Methane in coal mines is an ever present hazard resulting in loss of lives and serious economic consequences. For effective control of methane, ventilation alone may not be totally adequate in some situations. In order to deal with such cases, new methods for the control of methane are being researched. One such method based on biotechnology has been investigated in Canada in the past several years. This method involves bringing methane oxidizing micro- organisms into contact with coal to oxidize the methane released to non-flammable products.

Jan 1, 1988

By Ramana. G. Reddy, Haoxing Yang

The electrodeposition of zinc from zinc oxide using urea and choline chloride mixture in a molar ratio 2:1 is investigated in different experimental variables, namely, the concentration of added [BMIM]HSO4, temperature, and applied cell voltage. The additive, [BMIM]HSO4, was determined to have beneficial effect on the current efficiency, energy consumed in the process and surface morphology of the deposits. The highest current efficiency (92.6%) and lowest energy consumption (2.92kWh/kg) was obtained for solution with 20mg/mL [BMIM]HSO4. The morphology showed the formation of absorbed additive layer on the cathode at higher concentration of additives. Experiments were conducted at different temperatures between 343K and 388K and at various applied cell voltages between 2.7V to 3.6V to determine the best experimental conditions. By varying temperature, highest current efficiency (91.3%) and lowest energy consumption (2.69 kWh/kg) was obtained at 373K. The electrodeposition process is enhanced between the applied voltage 3.0-3.3V by achieving lower energy consumption (2.75~3.06kWh/kg) and higher current efficiency (88.4~89.7%). SEM images showed grain size is significantly increased in higher applied voltages. While at higher temperatures, it seemed to generate particle growth as clusters at the outer deposit layer.

Jan 1, 2014

By Carter A. J, Miller D. M, Holder N. H M, Van Aswegen P C

The Harbour Lights Mine situated at Leonora in Western Australia, mines a refractory sulphidic gold ore. The main sulphide minerals are pyrite and arsenopyrite. Due to the association of gold with the pyrite and arsenopyrite, gold recovery is not amenable to the normal cyanidation process.A pyrite/arsenopyrite flotation concentrate is produced at Harbour Lights. This concentrate has been stockpiled for the past two years.A bio-oxidation process (BIOX«)* to treat refractory gold flotation concentrates has been developed by GENMIN in South Africa. Harbour Lights acquired the technology from CRL BIOX« Pty Limited in Brisbane, to treat the refractory gold concentrates.

Jan 1, 1992

By P. Moran

A promising and increasingly popular tailings management strategy is to place cemented tailings underground as backfill. The placement of cemented tailings results in enhanced geotechnical stability and a purportedly more geochemically stable tailings form with lower leaching potential. Conventional subaerial tailings management can negatively affect water quality if weathering causes acid rock drainage and metal leaching (ARD/ML) to occur, whereas cemented tailings can limit leaching via porosity and permeability reductions and contribute alkalinity to limit the potential for ARD/ML. Cemented tailings backfill appears to be better, but how can this advantage be proven? Currently, cemented tailings backfill is utilized at mining operations internationally, but there is limited guidance on performing geochemical characterization and associated evaluation of the potential impacts to water quality. As a result, various approaches to simulating the leaching behavior of cemented backfill have been utilized, including some methods that are unlikely to represent weathering under site-relevant conditions. American Society for Testing and Materials (ASTM) Standard Test Method C1308-08 is a diffusion testing method initially developed to assess constituent release rates from solid nuclear waste forms. ASTM C1308-08 uses intact cylinders that more closely represent actual backfill than methods that require crushing or size reduction. It is widely believed that leaching from actual cemented tailings is controlled by diffusion through small pores that exhibit limited exposed surface area, making diffusion testing particularly applicable to cemented tailings placement.

Feb 27, 2013

In the new flowsheet for Inco Limited's S02, Abatement Project at the Copper Cliff, Ontario operations, a copper/nickel sulphide flotation concentrate will be flash smelted, then converted to Bessemer matte. As in current practice, this will be slow-cooled and separated into components by magnetic separation and flotation. The copper content will emerge as a chalcocite concentrate (impure Cu2S), containing some nickel. This copper sulphide will be converted to copper metal.

Jan 1, 1993

By Francis B. Gularte

The Dalles Dam is located 192 miles upstream from the Columbia River?s mouth. As part of an effort to increase survival rates for young salmon migrating downstream to the Pacific Ocean, a river spillwall was constructed to guide the young salmon into the thalway and out of the reach of predators. The spillwall consisted of 43 large precast concrete cells constructed onsite. The 120-ton cells are positioned on the bedrock riverbed to form the 830-foot-long spillwall. Large capacity post-tensioned strand anchors extend through ducts in the precast units, anchoring the wall to the basalt. One hundred seventy-eight tie-down anchors consisting of 30, 32, or 40 strands were installed and post-tensioned to secure the cells. The logistic and technical challenges presented by positioning, installing, and stressing the precast cells in the tailrace of a large dam required a high level of cooperation and planning between the owner, general contractor, subcontractors, and suppliers in order to finish the project within the allotted in-water work windows to minimize impacts on seasonal salmon migration.

Jan 1, 2010

By Taciana Rezende Pereira

O aço 10B06 é utilizado na produção de fio máquina para trefilação. Por ser produzido em aciaria elétrica, o teor de nitrogênio desse aço é elevado, o que pode causar envelhecimento por deformação, resultando em aumento de resistência e queda de ductilidade. Reduzir o teor de nitrogênio livre é uma forma de minimizar esse efeito, o que é feito pela adição de boro. O presente trabalho teve como objetivo realizar uma caracterização mecânica e microestrutural de materiais com teores de boro variando de 55 a 112ppm’s. Nas propriedades mecânicas obtidas no fio máquina, foi observada uma redução do limite de resistência com o aumento do teor de boro, evidenciando o seu efeito em minimizar o envelhecimento. Na análise metalográfica, as microestruturas apresentaram-se similares para todos os testes. Nas imagens do reagente Le Pera foram identificadas três fases, austenita retida e/ou martensita, ferrita e perlita. A presença de martensita não era esperada nesse aço. O que pode ter potencializado a sua formação é a presença de boro livre, que pode causar aumento da temperabilidade. Nos próximos passos desse trabalho serão feitas outras análises para confirmar esse resultado, como microdureza, MEV-EDS e detalhamento do processo produtivo do fio máquina.

Aug 17, 2017

By Travis Coleman, Elvis Ishimwe

Currently, more than 400 drilled shafts have been constructed by various contractors at the I-90/94 and I-290 Jane Byrne (Circle) Interchange, located near downtown Chicago, Illinois. Cross-Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP) tests were performed to evaluate the integrity and concrete quality of the drilled shafts installed at this project. For Phase I of the project the shafts were tested using CSL methods, and the shaft integrity was identified by analyzing the First Arrival Time (FAT) and the signal strength (energy) measurements. For the major portion of Phase II, the Illinois Department of Transportation (IDOT) accepted TIP testing as a substitute for CSL at the request of the contractors. The CSL testing results indicated 54 percent of the tested shafts had anomalies, and 78 percent of these anomalies were located within the lower three diameters of the shafts. To date, TIP testing results indicated the shaft integrity was as expected and acceptable for the all 34 tested shafts. A review of the testing results and a discussion of the detected anomalies are presented. In addition, a comparison of both TIP and CSL measurements is presented in this paper.

By Kexin Jiao, Zhijia Zhang, Jianliang Zhang, Zhengjian Liu

Carburization behavior of molten iron in blast furnace is an essential part of BF long campaign technology. Maintaining carbon content stable is an important prerequisite to ensure the high production of the blast furnace. In this paper, the important aspects of the research progress which mainly including the study of iron carburization at the upper and the lower parts of the blast furnace was reviewed. Indirect carburizing is the main way at the top of the blast furnace. The content of carbon in metallic iron increases with the reducibility of iron ore improved. The thermodynamics and kinetics conditions are good for carburization reaction to take place at the bottom of the blast furnace. Carbon content of molten iron increased by coke carburizing. Meanwhile, the drawbacks of the existing literature on iron carburization behavior were analyzed and new research directions of iron carburization were proposed in the future.

Jan 1, 2015

By A. Patrick Ryan

To many people, the word cartel implies illegality. However, although it is illegal in the US, cartels are an effective and legal way to conduct business elsewhere in the world. But be-fore we continue, what is a cartel? The American Heritage Dictionary defines a cartel as "a combination of independent business organizations formed to regulate production, pricing, and marketing of goods by the members." However, that definition does not fit many of the "cartels" we are examining today. The International Tin Council is an organization of both consumer and producer nations--no individual companies are represented. The buffer stock is used by the ITC to provide protection for both producers and consumers, and has only been in effect since 1955. (Earlier tin producers groups date back to 1921 when the Federated Malaysia States and the Netherlands East Indies formed the first intergovernmental tin agreement, known as the Bandoeng Pool, which only lasted three years.) The International Bauxite Association only dates back to 1974 when seven nations--Australia, the Dominican Republic, Ghana, Guinea, Guyana, Haiti and Jamaica--agreed to three main objectives: 1) to promote the orderly and rational development of the bauxite industry; 2) to secure a fair and reasonable return on the raw material for the benefit of the nations' citizens; and 3) to safeguard the interests of member countries in relation to the international bauxite industry. 1 Again this organization is composed of nations, not separate firms. This generally follows the pattern that the oil producing countries (OPEC) chose since the nations' mineral product-ion is controlled and often owned by the state. However, the group I am going to discuss fits the more classic mode of a cartel. The informal lead-zinc producers' cartel can be dated as far back as to Roman times when Romans are said to have imposed a quota system on British lead production to safeguard their Spanish lead mines. Also, the lead-zinc producers group is composed only of individual companies, not do not include any lead-zinc consumers. Finally, the activities of the group are not open to public scrutiny, and details are only now available due to a leak in the Australian government. At this point, it is necessary to split the two metals since while many of the members of the cartels produce both lead and zinc they do have different histories and marketing arrangements.

Jan 1, 1978

The engineering company's participation in quality assurance in the mining industry is twofold. Not only must it have such a program to ensure the necessary high standards for its own design and construction of a minerals processing plant, but it is also responsible as the "engineer" for both the selection and the quality of purchased equipment which goes into that plant. It is in this latter role that the engineer finds the most difficulty, or controversy, since while it is relatively easy to control his own performance, this is not ncessarily so when dealing with companies, all with their own ideas or standards. The engineer has perhaps rather reluctantly become more involved with the quality assurance of purchased equipment. This is because he has been used to writing performance type specifications and expecting the equipment manufacturer to provide the degree of quality, and control of that quality, for the product to meet the specified operating conditions. However, this has sometimes placed the manufacturer in a difficult position since to remain competitive in today's market conditions, he cannot always insist on product improvements or options which may in the long run be vital to reliable operation of the equipment.

Jan 1, 1982

By Steven Richardson, E A. Cameron, Reza "Ray" Jambakhsh

This paper outlines the design and implementation of a method to use Long hole Carbide drilling to blast an "Upper Blind Slot Raise" in the range of 12m (40 ft).

Jan 1, 1992

By Samuel B. Christy

At the last meeting of the Institute, several contributions were made to the subject of miners' aid funds. Such matters will always form important factors in the administration of large industrial enterprises. From the frequently remote and isolated position of mining properties, it is a subject that often forces itself upon the attention of the mining engineer. Local conditions are usually so variable that no single method can be found equally well adapted to all localities. At the same time, a study of different types is often suggestive and valuable, and it is with this in view that these notes are presented. The Miners' Fund of New Almaden is a remarkably successful example of what may be done for miners by a wise and at the same time firm management, by simply directing their own efforts and without incurring any great expense to the stockholders,—a practical consideration not without importance in most cases. The quicksilver mines of New Almaden are situated at a distance

Jan 1, 1885

H. Van F. Furman, Denver, Colo. (communication to the Secretary): There are some statements in Dr. Carpenter's interesting paper which appear to require explanation, if not modification.

Jan 1, 1901

By E. C. Roper

Landusky Mining, Inc. and Zortman Mining, Inc. are two registered Montana Corporations wholly owned by Pegasus Gold, Ltd. of Vancouver, B.C. The Zortman and Landusky Mines are located in the Little Rockies District of central Montana. The Zortman-Landusky mines produced 2,100 kg gold in 1982. A total of 3,250,000 t of ore per year are mined during the period March 1, to September 15, at an average grade of 1.04 gm/t (0.03 oz/t) gold and 13.4 gm/t (0.385 oz/t) silver at a cutoff grade of 0.35 grams of gold/ton (0.01 oz of Au/t) of ore. The stripping ratio during 1983 is anticipated to be 0.75/1 waste to ore. Combined average plant capacity of the two Merrill-Crowe plants is 9,840 lpm (2,600 gpm). The combined heap spray capacity of the two plants approaches 18,900 lpm (5,000 gpm). The mine employs approximately 200 people, about half of these work for the mining companies and the other half for the mining contractor, N. A. Degerstrom of Spokane, Washington. Net profit in 1982 for Zortman and Landusky Mining, Inc. approximated $4,900,000 at an average gold price of $11.40/gm.

Jan 1, 1983

By S Khadhraoui, T Yusuf, C Kirmse, E Hecker, R Degel, A Akouch, N Borowski, M Reuter

For an optimal design and control of metallurgical processes, a deep understanding of the thermodynamics of the governing reactions is required. Modelling the thermochemical behaviour of those reactions is complex, as it involves multi-component and multi-phase systems. For this purpose, thermodynamic computing systems such as FactSage™ (Bale et al, 2016), which combine Gibbs energy minimisation routines with large databases of optimised thermodynamic data of solutions and compounds, have been used within the SMS group GmbH. Recently, the successful integration of those thermodynamic computing systems into the digital platforms of SMS has been achieved through ChemApp, which made running complex thermochemical calculations in Python-integrated development environments possible. ChemApp is a programmer’s package for thermochemistry and incorporates the Gibbs energy minimiser of FactSage™ as reported by Petersen and Hack (2007) as well as by Zietsman and Petersen (2018). The digital platforms link the fundamental and the industrial aspects together and can be applied as a process advisor, or for the evaluation of the environmental footprint and the economic implications of different process routes, as discussed by Reuter (2023). Two examples illustrating the progress of the developments in this regard will be introduced: 1. The Tilting Refining Furnace (TRF) for copper scrap recycling and refining to anode copper (the BlueControlApp). 2. Dephosphorisation control for the oxygen steelmaking process (Basic Oxygen Furnace (BOF)).

Jun 19, 2024