Search Documents

By E. Bratygin, G. Gazaleeva

"The article describes the analysis of methods and criteria of selectivity of optimal ore preparation schemes. Traditional criteria based on study of physical-mechanical properties of ores give the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production.Further on estimation is given to different criteria of the crushing selectivity, the new criterion is offered, the definition of which is done by results of an optical microscopy– the estimation of a valuable mineral release degree. The final estimation of the crushing process selectivity L? is performed by a calculation of a ratio of the valuable mineral free grains quantity in a desired size grade of a crushed material to the valuable mineral free grains quantity in a desired size grade of a raw product.Besides, optimality assessment of using the specific crushing unit is preliminary performed according to a maximum crushing degree of a material, however, the priority is given to the maximum selectivity criterion. The check of the proposed criterion was done when comparing the crushing of niobium bearing ores of the Vishnevogorskoye deposit in cone inertial and centrifugal impact crushers. Different operation modes of crushers were also checked. The comparison of the crushing selectivity criterion L? showed that the centrifugal impact crusher (CC) has the value of the selectivity criterion lower than the cone inertial crusher (CIC). For the crusher CC the criterion L? is 0.82 – 0.87 units, whereas for the crusher CIC – 1.43-1.755 units. The best crushing mode for the crusher CIC-300? is as follows: turning angle of debalance is 120°, peripheral speed of a cone rotation – 1,420 rpm, specific energy consumption – 6.99 kW?t/t.INTRODUCTIONIt has been shown that the most efficient techniques of mineral raw materials disintegration are selective crushing enabling to produce liberation of particles at maximum use of destruction techniques by borders of minerals cleavage. These days, such techniques are usually called special disintegration techniques (Jankovic & Valery, 2015), and they are used in 3–4 crushing stages. The selection of optimal crushing techniques is performed based on the following main parameters:- degrees of crushing, calculated based on granulometric features of raw and crushed products;- selectivity criterion defined according to useful mineral release and slime ability degree; and- traditional criteria (Gazaleeva et al., 2015) of choice based on study of physical-mechanicalproperties of ores gives the comparison of obtained figures with a reference standard or statistic data and the selection of the ore preparation scheme is made on a basis of a similar scheme from the existing production."

Jan 1, 2016

By G. K. Burgess

THE question of the allotropy of iron, in spite of a vast amount of experimental work and perhaps an even greater amount of theorizing, is not yet settled. That there is a definite transformation in iron near 900,° the A3 point, is generally recognized, as well as the fact that the temperature of this transformation is lowered by the addition of carbon and metallic elements. On heating, the transformation Ac3 is always found at a higher temperature than the transformation on cooling, Ar3. Whether the A3 transformation is sharp like the melting point of a pure substance, or extends over a considerable range of temperatures, embracing perhaps as a lower limit the A2 change, appears to be still an open question for pure iron. The nature and identity of the A2 transformation, it would appear from recent publications, has not yet been satisfactorily settled. In the present paper a critical, historical summary is given of the experimental investigations of the location of A2 and A.3 in pure iron, together with brief mention of some of the theoretical aspects of the subject, and an account is given of a series ?of experiments carried out with several samples of very pure iron which were studied by two methods of thermal analysis in the range from 5000 C. to 1,000° C., and which it is believed furnish a contribution of considerable interest as to the location and nature of the A3 and A2 transformations. Great attention has been given to the details of experimental manipulation and to the preparation of the samples, as it was soon found that some of the discrepancies noted in the work of many experimenters may be traced largely to lack of precautions which we have found essential. For example, to anticipate somewhat, it is necessary to provide a suitable practically gas-free furnace, the heating and cooling of which may be regulated to a nicety. To render a minimum the deforming effects on the cooling and heating curves of the poor conduction of the sample, it must be of a form and mass to pass on its heat rapidly and completely to the thermocouple; and finally the sample itself must be freed from gases which, if present, further mask the definiteness of the heating and cooling curves. We, have also varied within wide limits the several factors which may influence the determination of the exact location and shape of the transformation ranges, especially the mass and preparation of sample, rate of heating and cooling, design of furnace; and finally, as nearly as it is experimentally possible, we have worked with a substance approaching pure iron, free from occluded gases and other impurities, and contained within a vacuum.

Jan 10, 1913

By C. G. Dunn

IT is well known that plastic deformation alters many of the properties of a metal and subsequent heat-treatment partially or completely restores these properties.1 In the deformed or strained state, the metal is unstable and tends to change toward a condition called a "strain-free state." The transformation occurs through recovery, recrystallization, and grain growth-processes that may take place singly or in combination. The distortion of the lattice of an individual grain of a metal in a state of strain may be rather complex in nature, because plastic deformation produces: (I) dislocations within mosaic blocks; (2) elastic variations of the lattice spacings; and (3) gross alterations throughout the lattice, especially along slip planes, along composition planes between a grain and its mechanical twins, and along boundaries of deformation bands. These gross alterations are of the nature of bent planes or rotated regions of the crystal lattice and are revealed by a spread in the orientation of the grain. Although we cannot describe these strains and their formation accurately because of insufficient knowledge, we can, nevertheless, use the information as well as possible to obtain a better understanding of recovery processes. In recovery, the lattice of a grain is not made anew as it is in recrystallization, but is improved or mended in such a way that the basic structure remains unaltered. Until recently observations were that recovery produced no marked changes in the shapes of spots in Laue diffraction patterns, whereas recrystallization did, but now it is known for silicon ferrite2 that Laue spots may become quite sharp entirely through recovery. Consequently, the shape of Laue spots alone would not be a suitable test to distinguish between recovery and recrystallization. There is considerable evidence that the micro- structure usually does not change visibly during recovery. Absence of a visible change in the microstructure, therefore, provides a sufficient test of recovery in many cases. However, including this observation in a definition of recovery as a necessary condition (this is usually done) is unfortunate, because recovery may, as will become evident later, produce new grain boundaries that are visible not only in the microstructure but also in the macrostructure. For the present, therefore, let us say that a necessary condition for a process to be one of recovery is that the principal orientation or orientations of a deformed grain be essentially unchanged throughout the transformation toward the strain-free state. Several transformations may occur that fulfill this condition, and the nature of the distortion in a grain indicates what these must be if the lattice is to be mended in part or fully. Consequently, it will be convenient as well as

Jan 1, 1946

By Earl T. Hayes

THIS BIBLIOGRAPHY has been assembled to aid research by the Bureau of Mines, and others on high-purity tungsten. It appears approximately 50 years after the development of ductile tungsten-one of the first metals to be produced in a high-purity form. Requirements of the missile age are ever more demanding that engines rout hotter and space vehicles fly higher and faster. Thus, it has become necessary to reexamine all conventional materials of construction as well as to investigate new combinations. At this stage of our technology we have alloys capable of operation at 1,800° F. and several possibilities of developing some. that will be satisfactory up to 2,500° F. Strength-weight comparisons, detrimental to tungsten at, lower temperatures, disappear at this point, mid tungsten or its alloys appear to be the only metal capable of operation at truly high temperatures. The aim of this bibliography has been to include only references that concern improving the purity of tungsten-from processing the ore to treating the finished metal. In this sense it is a selected and not a critical bibliography. The period front January 1911 through February 1959 has been covered. Because repent literature has the greatest, value, most of the selected items refer to publications issued within the pest 5 years.

Jan 1, 1960

By R. P. D. Graham

It is almost exactly two hundred years since the foundations of the mining and metallurgical industries in Canada were laid. There '."'as nothing spectacular about this early start. It had to do with the most basic phases of these industries-the mining of coal and iron ore, and the manufacture of cast and wrought iron. At several points along the coast of Cape Breton island, coal seams may be seen outcropping quite conspicuously, and it is probable that they had been observed, and possibly worked in a small way, in very early times. However that may be, these coal seams have the distinction of being the first in North America of which there is any printed record, reference to them appearing in a volume by Nicolas Denys which was published in Paris in 1672. Regular coal mining in the district did not commence until about fifty years later, however. The metallurgists started their operations along the north shore of the St. Lawrence river. Here, at many points between Montreal and Quebec, are to be found deposits of bog iron ore, and in 1 730 a furnace for smelting such ore was established on the St. Maurice river. The St. Maurice forges continued in operation until 1880, and throughout that long period they were famed for the fine quality of castings produced, and also for a-superior wrought iron.

Jan 1, 1924

When the Organic Act of 1910 established the Bureau of Mines within the Department of the Interior, the Bureau's programs involved only health and safety research and, education, and fuels testing. As the Federal Government's primary agency for research in minerals, the Bureau has expanded its scientific and technological investigations to mining, processing mineral substances, eliminating occupational health and safety hazards in the mineral industries, economic development, and resource conservation. Today, Bureau activities cover a broad spectrum of programs for meeting the diverse (and sometimes conflicting) needs of mineral industries, government, and the public. In the 1960's, the Bureau initiated programs to resolve environmental problems associated with past mining and mineral processing. In the 1970's, the energy crisis raised the national consciousness concerning our limited supplies of domestic mineral and fuel resources. Dependence on foreign sources of raw materials critical to our national economy and competition from other countries for these world supplies stimulated the need to conserve and use with intelligence the Nation's minerals, metals, and fuels.1

Jan 1, 1977

By Gregory B. Beacher

Analyses have been performed on geotechnical properties of copper, uranium and phosphate (gypsum) tailings materials, with the intent of identifying typical measures of variability within and among sites, and of characterizing such variability for use in reliability modeling of tailings embankments. In all, data from approximately 41 sites were analysed. Fairly consistent results were obtained for within site variabilities. However no one probabilistic model was found to be applicable to all sites. The distributional forms for most of the data sets are regular, and tend toward Normality when spatial trends are removed. At many of the sites sufficient in situ data were available to allow estimates of vertical autocorrelation distances and measurement noise. Available data indicate that variability in pore pressures may have a more important effect than strength property variation. A major problem in interpreting available strength property data results from the unknown drainage conditions during testing.

Jan 1, 1983

By A. C. Fieldner, W. A. Selvig

Information concerning the fusibility of coal ash has become of considerable value to the consumer of coal, mainly in connection with the troublesome formation of clinker resulting from the melting of the ash constituents of the burning coal. The growing interest in such data has led the Bureau of Mines to make a general survey of the "fusing" or "softening" temperatures of the ash from coals of the United States. It is hoped that this information when used together with the large number of coal analyses published 1 by the bureau will assist the consumer of coal in comparing different coals, and in selecting the coal best adapted for his purpose.

Jan 1, 1922

By W. G. Worcester

THE chief object in presenting this paper on bentonite is to attract general attention to one of the least known and most neglected industrial minerals of Canada, a mineral of extensive commercial possibilities, as evidenced by its development and exploitation in other countries, principally in the United States and Germany; countries upon which some of our most important Canadian industries are dependent for their supply of special clays, such as Fuller's earth and activated bentonite. It was in view of these conditions and the knowledge of the presence of large quantities of bentonite in the Canadian West that the work here reported on was under-taken. While the investigational studies have not been completed, the results indicate that among the many samples tested there are some of real merit and industrial importance. While it has been the author's privilege to examine deposits and samples of bentonite from all of the Western provinces, his chief activities in the field and in research studies have naturally been confined largely to Saskatchewan materials. Notwithstanding this, however, this paper is presented in the hope that it may stimulate a more general interest in, and study of, Canadian bentonites as a whole, a matter of such importance that provincial boundary lines should be overlooked. GENERAL CHARACTERISTICS OF BENTONITE According to Schurecht and Donda (1), bentonite is commonly composed of the mineral montmorillonite, (Mg,Ca)O.Al203 5SiO2 .nH2O, though some are known to consist of beidellite, Al2O3 3SiO2.nH2O: where n is approximately 4, and in certain cases the Al2O3 may in part be replaced by Fe2O3. For present purposes, however, it may be sufficient to state that, in general, bentonite is a "soapy' clay-like mineral or group of minerals composed largely of hydrous aluminium silicate, but frequently carrying small percentages of the alkalies, alkaline earths, and free silica, as well as silicates, gypsum, and other admixed detritus such that purification is usually necessary.

Jan 1, 1937

By G. J. Slavens

The Bureau of Mines has devised technology to recover cobalt, nickel, and byproduct copper from domestic lateritic material using an oxidative, ammoniacal ammonium sulfate leach. Nickel, cobalt, and copper were recovered by solvent extraction and electrowinning. To reduce the cost and complexity of cobalt recovery, an alternate method using lig-nite to extract Co3+ was investigated as reported herein. In the first 25 BV (bed volumes) of solution contacted with lignite, 97 wt pct of the Co3+ was extracted in & downflow column at pH 9.3. After 85 BV, the lignite was loaded to 1.5 wt pct Co3+ and further ex-traction was minimal. The lignite extracted cobaltic ammine complexes rather than cobalt ions and was nonselective as to other -metal cations and ammonium ions. Deleterious cations and 80 wt pct of the nonammine ammonium ions were removed prior to acid elution of the lignite. The removal of the ammines prior to elution to produce an ammonium-ion-freeCo3+ eluate was only partially successful. Thus Co3+ removal from ammoniacal solutions by lignite is technically difficult and economically unfeasible. It was also determined that reduction of Co3+ to Co2+ occurred during the extraction-elution process.

Jan 1, 1984

By Wallace W. Key

This report concerns types, quantities, specifications, and uses of non-metallic minerals as a basis for improving their supply, conservation, and utilization. Supply-demand details concerning mineral fillers, rooting granules, and roofing rock used in asphalt are incorporated in this report, along with highlights on production and sales of rooting, floor tile, and other related asphalt products of California. Comparable data for the United States are included. Although large quantities of commercially prepared mineral fillers are used in asphalt for paving and related applications in other States, addition of commercial fillers for these uses rarely is required in California because of the natural tines available. On the other hand, California manufacturers of asphalt products other than having utilize about 300,000 tons of asbestos, diatomite, limestone, mica, soapstone, and other nonmetallic minerals as filler, mainly for reeling and flooring. Also about 500,000 tons of roofing, granules is produced in California, most of which goes into roofing manufacture in California. In addition. A significantly large and growing tonnage of relatively coarse mineral aggregates Ire used on low-angle, built-up, asphalt roofs to produce in attractive surface and offer protection against the clements. Clearly ill minerals used in asphalt products manufactured in California come from local sources, except asbestos and mica--and there are indications that local deposits of those commodities could be utilized in some use categories.

Jan 1, 1966

By Wallace W. Key

This report concerns types, quantities, specifications, and uses of non-metallic minerals as a basis for improving their supply, conservation, and utilization. Supply-demand details concerning mineral fillers, roofing granules, and roofing rock used in asphalt are incorporated in this report, along with highlights on production and sales of roofing, floor tile, and other related asphalt products of California. Comparable data for the United States are included. Although large quantities of commercially prepared mineral fillers are used in asphalt for paving and related applications in other States, addition of commercial fillers for these uses rarely is required in California because of the natural fines available. On the other hand, California manufacturers of asphalt products other than paving utilize about 300,000 tons of asbestos, diatomite, limestone, mica, soapstone, slate, and other nonmetallic minerals as filler, mainly for roofing and flooring. Also, about 500,000 tons of roofing granules is produced in California, most of which goes into roofing manufacture in California. In addition, a significantly large and growing tonnage of relatively coarse mineral aggregates are used on low-angle, built-up, asphalt roofs to produce an attractive surface and offer protection against the elements. Nearly all minerals used in asphalt products manufactured in California come from local sources, except asbestos and mica--and there are indications that local deposits of these commodities could be utilized in some use categories.

Jan 1, 1966

By John J. Henn

Ten proposed processes for the recovery of manganese from domestic resources as a high-grade oxide product are described. Nine of the processes employ sulfur dioxide, sulfuric acid, or a combination of both for leaching. The tenth process utilizes sulfur dioxide to sulfatize the ore at 600° to 850°C before water leaching. In addiction to these ten complete processes, six processes from the patent literature are described. Methods for receovering MnSO4?H2O are also reviewed.

Jan 1, 1968

By McMillan W. D.

Vermiculite is the name of a group of micaceous minerals characterized by their property of exfoliating when heated and thereby increasing many times their original volume. The resulting product has excellent heat-and sound-insulating properties, is used as a lightweight aggregate, and has numerous other industrial applications. Deposits of vermiculite occur in areas of pre-Cambrian rocks of the Llano uplift of central Texas, particularly in Burnet and Llano Counties. Because of the growing economic importance of vermiculite products, the Bureau of Mines undertook a detailed investigation of several deposits in Llano County. This investigation was completed in February 1947. The work comprised topographic surveys of five deposits, drilling with a 4-1/4 inch Parmanco power auger drill, and laboratory evaluation of samples. 342 drill holes, aggregating 4,905.5 feet, were completed, and 377 samples were taken. Laboratory evaluation of the vermiculite comprised expansion tests on both crude and beneficiated samples. The products obtained were compared with commercial-grade vermiculite from Montana.

Jan 1, 1949

By Ivor Hawkes

The purpose of the development described in this report and as stated in the contract work statement is to "design, develop, fabricate, test and demonstrate, and deliver to the government permissible low cost cylindrical stress gauges and associated components capable of measuring change of stress as a function of time in underground coal mines. The cylindrical stress gauges shall be suitable for installation in bore holes". The technique adopted for measuring rock stress changes is to preload a steel cylinder diametrically across the sides of a 1-1/2 in diameter bore hole and detect deformation of the cylinder from stress changes in the rock, by means of a vibrating wire transducer. By calibration, changes in the period (time for one wire oscillation at the natural frequency) of a high tensioned wire stretched diametrically across the cylinder in the direction of load application are related to stress changes in the rock. To completely evaluate the stress field change in the plane of the bore hole, three gauges set at an angle to each other are required.

Jan 1, 1973

By K. Reinhardt

THE idea of burning blast-furnace gases directly in gas-engines, instead of under steam-boilers, as had previously been done, was first put into practice barely ten years ago, almost simultaneously in Great Britain, Germany and Belgium. The pioneers of this movement made their first experiments with small engines. After these experiments had given satisfactory results, and it had been shown that the thermal value of the poor blast-furnace gases, in spite of defective scrubbing, could with safety be directly transformed into mechanical work in the gas-engine, there very soon arose a considerable demand for gas-engines of large power, similar to the large steam-engines employed in metallurgical works. In face of these sudden requirements, the gas-engine builders were placed in a difficult position; for up to that time the gas-motor was considered as suitable for small engines only, and it was generally believed that the limit of size bad been attained with 100 to 150 effective h.p. in a single cylinder. Manufacturers of gas-motors, however, did not underrate the advantages offered by this new field for their manufactures, and it so happened that in Germany the Berlin-Anhaltische Maschinenbau-Gesellschaft, of Dessau, was the first to undertake the construction of a 600-h.p. two-cycle gas-engine, with two cyl¬inders of the Oechelhäuser-Junkers type, for the Hoerder Mining & Smelting Company. The engine was started in 1898, and, with a few improvements and alterations, is still working satisfactorily. This engine worked with astonishingly high of efficiency, considering the period. The builders were therefore

Nov 1, 1906

By R. A. Cattell

With the surrender of the Japanese Imperial Government as a climax to the capitulation of the German High Command , the main objective of the Petroleum and Natural Gas Division pivoted from war assignments to its main normal functions . One of these functions is to give wide public distribution to valuable technical facts which the Division has obtained through research on petroleum , natural gas , helium , and related subjects . During the war years many engineering data and scientific facts could be released only on a restricted basis as reports to war agencies and others immediately concerned . Moreover , many of the wartime reports contained masses of detailed data that were prepared under stress to meet emergency schedules . For peacetime publication and application , these data must be reviewed , correlated , and rearranged so as to present the essentials in proper form . To illustrate , a wartime report of 50 pages might be resolved into one curve in a composite graph for a peacetime publication . Another factor affecting the orientation of the work of the Division is the broader horizon of research revealed by its war activities . Fundamental research and careful engineering analyses are just as important in time of peace as in time of war; in fact , they should be more important to the forward view , because under peace conditions disrupting influences that distract from the orderly acquisition of knowledge are minimized . Therefore , the concerted effort has been not to " salvage " the results of the war activities , but to evaluate them on the basis of their relative importance in the future economy of the country . Where wartime investigations have pointed to peacetime accomplishments , the effort has been to give the corresponding type of work additional emphasis . This adjustment can not be made hurriedly , but many of the necessary preliminary steps on the new course have been taken ..

Jun 1, 1949

By A. Doroudgar, H. Noferesti

Unstable rock failure or rock bursting is one of the most dangerous problems in deep hard rock mines. This type of failure, that occurs uncontrollably, is associated with a significant release of strain energy from the surrounding rock. In this study, the numerical simulation of unstable rock failure was carried out using the three-dimensional explicit Lagranian finite-volume finite difference method to identify the onset and location of unstable failure events in the model. On this basis, a numerical simulation of mine pillars with width-to-height ratios of 0.5, 2 and 3 was performed. A criterion was developed, based on the calculation of the elastic strain energy, to determine the prone areas for the initiation of rockburst in the models. The results of this study showed that, in softer loading systems, due to large amounts of stored elastic strain energy, an unstable equilibrium is established, which leads to the rapid transfer of strain energy to the rock in the form of violent failure. It was also found that the unstable failure starts at the corners and free surface of the model. The new criterion developed in this study may help predict the occurrence of rockbursts in slender pillars and the design of pillars to control human and financial losses caused by this phenomenon.

Nov 27, 2024

By B. Birol, M. N. Saridede

"Slag density is a significant factor in determining the process efficiency of the electroslag remelting (ESR) process, where calcium fluoride (CaF2)-based slag is formed synthetically to refine metal ingots. Although there are some former studies investigating the density of CaF2-containing slags, the prediction models focusing on them are applicable only to some specific systems. The present study aims to build a model to predict density for a wide range of CaF2-containing ESR slags. To investigate density for various slag compositions, CaF2-Al2O3-based and CaF2-Al2O3-CaO-based slag compositions were prepared. Additionally, some minor constituents like FeO, MgO and MnO were added to a 5:3:2 CaF2-Al2O3-CaO slag in order to investigate the effects of these constituents on the slag. The volumes of the prepared slags were measured in a tube furnace at 1450-1550 °C using the sessile drop technique, and their densities were calculated. The results showed that for the slags, density is related to optical basicity, and therefore a prediction model based on an Arrhenius equation was built. The model was tested with data from literature, and its limitations and validity are discussed.IntroductionThe electroslag remelting (ESR) process is a refining method in which a metal ingot is remelted under a synthetic slag. These synthetic ESR slags are mainly composed of calcium fluoride (CaF2), calcium oxide (CaO) and aluminum oxide (Al2O3). Other constituents like iron oxide (FeO), magnesium oxide (MgO), manganese oxide (MnO) and chromium oxide (Cr2O3) are added to this system in relatively low amounts, according to the type of steel ingot to be refined. The prediction of slag properties, such as electrical conductivity, viscosity and density, is crucial for the selection of the synthetic slag in order to obtain the required process parameters, like temperature, the passing time of the molten metal droplet through the slag, and metal-slag separation (Akbari, Reitz and Friedrich, 2009; Hara and Ogino, 1981; Mattar, El-Faramawy and Fathy, 2002; Mehrabi, Rahimipour and Shokuhfar, 2005; Presoly, Korp and Schneider, 2008).As slag density affects metal-slag separation in the ESR process, predicting the density of an ESR slag is important for appropriate refining and improved product quality. Although there are many studies investigating the density of slags (Akbari, Reitz and Friedrich, 2009; Aune, Hayashi and Sridhar, 2005; Hara and Ogino, 1981; Matsushita, 2011; Mills and Keene, 1987, 1981; Seetharaman et al., 2013; Shu, 2007; Shu and Chou, 2013; Sikora and Zielinski, 1974; Xu et al., 2012; Zhang and Chou, 2010), the prediction models built are generally valid for oxide-containing slags (Aune, Hayashi and Sridhar, 2005; Bottinga and Weill, 1970; Mills and Keene, 1987; Seetharaman et al., 2013; Shu, 2007; Xu et al., 2012; Zhang and Chou, 2010). These models were built on either the molar volumes of the constituents (Bottinga and Weill, 1970; Mills and Keene, 1987) or the thermodynamically calculated enthalpy or free energy of mixing, which can be applied to a system containing constituents sharing an ion, such as an O- ion for oxide systems (Aune, Hayashi and Sridhar, 2005; Hillert, 1980; Persson et al., 2007). Some recent studies modeled the density of some oxide slags on their optical basicity (Shu, 2007; Shu and Chou, 2013; Xu et al., 2012; Zhang and Chou, 2010)."

Jan 1, 2016

By David Sutherland

The treatment of a complex orebody requires a thorough understanding of its mineralogy. If there is a poor appreciation of the mineralogy involved, difficulties can emerge with the efficient exploitation of the resource. Recently, there has been a lot of interest in automated image analysis systems, which aim to improve the reliability and accuracy of the data, which can be gathered. In this sense, the paper point out the process mineraloggy for complex ores. Mineral modal analysis a description of texture and liberation studies are the basis of these measurements. They have been applied to a wide range of mineral systems including copper, lead, zinc, silver and gold.

Sep 13, 2001