Search Documents

By R. F. Tenney

The performances of four anthracite-burning stokers have been observed under identical 74-hp. steam boilers. Fifty runs of 12 and 24 hours' duration were made in accordance with the test code of the American Society of Mechanical Engineers (ASME). The capacity of each stoker for burning anthracite has been determined, the heat efficiency at each fuel rate has been computed, and the various significant items of hear loss have been estimated. The operating data and results from each run are tabulated in this report in the form used in the test code. The heat efficiencies and most significant operating data for each run are also presented graphically for each stoker to establish the trends with increasing boiler outputs, The tests show that rice anthracite can be burned on stokers adapted to its use at heat-conversion efficiencies of 82 percent or more under continuous firing. These high efficiencies are maintained with fuel inputs 30 percent higher and lower than the peak efficiency rate. Moreover, a heat efficiency of 70 percent or more is obtained at 50 percent of the optimum fuel rate, even though the excess air into the furnace cannot be held below 150 percent.

Jan 1, 1960

By D. W. Zandee

"IntroductionHaving mined an economic mineral bearing rock which is of insufficient grade to warrant direct smelting, upgrading or beneficiation is required to make it an economically viable ore. The first step in effecting the concentration process is comminution or sequential breaking of the rock to allow liberation and subsequent recovery of the desired mineral particles. Desirably the ore could be broken down to the point where the valuable mineral is completely liberated to maximize the chance of recovering as much of it and in as pure a form as possible. The number of energy intensive stages of breakage required to attain this goal depends on many physical characteristics of the ore such as hardness, friability, toughness, grain size, existing fracture planes and particle shapes.Commonly the distinct stages are primary, secondary and often tertiary crushing and finally grinding. To increase the efficiency of each stage of size reduction, pre-treatment sizing is common.Crusher feed is commonly scalped of large pieces or screened for reduction crushers and classified for secondary grindingcircuits.Although crushing and screening is employed for many different products, this chapter reviews current practice in larger tonnage metalliferous ore treatment plants.Current practice is to use large gyratory or jaw crushers for primary crushing and some sort of gyrating or cone crushers for additional stages of reduction. For autogenous or semiautogenous grinding circuits only the primary crushing stage is necessary, the balance of the work being performed in the grinding stage. For conventional grinding circuits using ball mills or combinations of rod and ball mills, secondary, tertiary and even quaternary crushing stages are normally required.Older type crushers such as stamp mills, double rolls, sledging mills and hammermills are no longer common but are used for small tonnage special processes.Important to efficient crushing are a variety of sizing devices such as grizzlies and vibrating screens. Products at different stages must be stored to give surge capacity and allow controlled feeding rates through mechanical and gravity feeders. These storage piles, bins and feeders as well as crushers and screens are commonly integrated into a total facility by means of conveyor systems. Most often these are endless rubber belts driven by simple or multiple drive mechanisms usually consisting of electric motors and speed reducers."

Jan 1, 1989

By Akira Yazawa

The similarities and differences in copper, nickel and lead smelting processes are discussed based on the sulfur-oxygen chemical potential diagrams and the free energy minimization assessments using a thermodynamic software. The prominent features of copper smelting are ascribable to the fact that copper has a strong affinity for sulfur but weak for oxygen and the liquid phase immiscibility between Cu and Cu2S. During the oxidation of sulfides, nickel metal is not stable except at temperatures higher than 1500°C, well miscible with its sulfide, and is oxidized more easily than copper. Metallic lead looks as stable as copper during the oxidation of the concentrate but Pb and PbS. are much more miscible with each other and the vaporization loss is considerable. In the reductive smelting of oxides, the effects of oxygen potential and temperature on the copper contents in slag are not significant due to the monovalent character of copper and the reduction of copper content in slag is not easy in practice. The effect of the slag compositions on the oxidic metal contents of slag is much more significant for lead than either copper or nickel. Due to the immiscible nature between Pb and Fe, high grade lead bullion is easily obtained and lead is more tolerant to impurities.

Jan 1, 1998

By E. Kozeschnik

A new model is presented for the simulation of the evolution of precipitates in a multi-component multi-particle multi-phase environment The mathematical formulation as well as the physical background of the model are briefly introduced and its capabilities are discussed on the example of a precipitation sequence in a complex steel. Keywords: Modeling, precipitation kinetics, nucleation, growth, coarsening

Jan 1, 2003

By W. Linwood Haden

Fullers earth has been mined since about 1920 in southwest Georgia and the adjoining area of Florida. In 1935, the mineral was named "attapulgite" after the source of a sample near the town of Attapulgus, Decatur County, Georgia. Mining and processing of the clay was described in a 1930 publication1 at a time when petroleum refiners were the major users. In the years since then, the uses and users of attapulgite have multiplied, and both mining methods and processing methods have been changed to optimize the clay for the new uses. A comprehensive review of the properties and applications of attapulgite 2 has been published. Only a brief review will be given here to explain the properties being sought and to show how these properties are optimized by mining and processing practices.

Jan 1, 1972

By H. W. Renner

The paper industry is an $80 billion/year business that is the largest consumer of industrial minerals. Paper industry generally refers to paper and paperboard products, including pulp mills. Grades and uses of paper and paperboard are very diverse, including such things as napkins, paper plates, corrugated boxes, magazines, newsprint, currency, and copier paper. Only about 40% of paper utilizes industrial minerals as fillers or coating materials. Minerals are used for both functional and economic reasons. Most often, minerals such as kaolin clay and calcium carbonate are used to improve print quality, brightness and opacity of paper. The minerals can be added as fillers into the paper in the wet end of the papermaking system, or can be applied as part of a coating to the paper. Coated papers are the highest quality paper, being used for magazines, advertising brochures and annual reports. Common uses for filled uncoated paper are books, copier paper, envelopes and many of the Sunday newspaper advertising inserts.

Jan 1, 1993

By Munetaka Iwasaki

Nitrogen strongly affects mechanical properties of steel and therefore we may sometimes modify the various processes for its content. Numerous studies based on the results of chemical analysis of quenched samples were reported with a few exceptions of Hot Sievert method. The technique always poses a risk of uncertainty whether the true content of nitrogen in liquid metal is measured or not. In this study vacuum remelting under relatively low pressure was done to enhance gas phase mass transfer. Total pressure of the melt chamber was about 10-3 pa and electron beam heating was used. Mass spectroscopy was used for the direct observation of the rate of denitrization. Nitrogen molecules or atoms were detected by a mass spectrometer set above the melt. Continuous monitoring of the intensity of the fixed mass number may reflect the transfer of nitrogen from the melt to the vacuum. The results of the new and conventional techniques agree, both technique can be verified.

Jan 1, 1999

By Filiz Sahin

This paper presents a synthesis of TiB2 via carbothermal reduction method using a mixture of TiO2, B4C and C prepared in molar ratio of 2:1:3. Reduction experiments were carried out in a high temperature graphite furnace in a graphite crucible under argon atmosphere at different time (0, 15, 30 and 60 min.) and temperatures (1400, 1500 and 1600 °C). The products obtained were investigated using XRD technique.

Jan 1, 2008

By Michael J. Callow

THE PROPERTY of Mount Isa Mines, Ltd., is located at Mount Isa, Northern Queensland, Australia, at roughly 20" south latitude. It is 600 miles from Townsville on the east coast, the port for Mount Isa, 1200 miles from Brisbane and approximately 1600 miles from Sydney in New South Wales. Living conditions in the camp, though wild and crude at the commencement of building, are now excellent and little has been left undone to provide comfort and attractiveness. The climate being warm and dry, many of the buildings are built on posts, 8 to 10 ft. off the ground, with spacious screened-in verandas. Club houses, stores, school, hospital and ice plant have all been provided by the company as well as modern conveniences, such as running water, shower baths, electric lights, septic tank arrangements, tennis courts and amusement grounds.

Jan 1, 1932

By MATT RENAUD, Mustafa Kumral

Mining corporations have spread their operations worldwide in the last few decades. The reason behind widening operations geographically can be seen as it being part of a risk diversification strategy. Given that the technical, financial and social risks are high, favorable deposits, taxation regimes and legislative frameworks create incentives for international mining operations. On the other hand, international mining activities add the risks of permitting, investing, operating and decommissioning to the corporations. These risks could emerge from defaulting, corruption, resource nationalism, social license to operate, and political and legislative uncertainties and instabilities.

By Yeatman, Pope

FOR many years geologists have felt that mining companies should adopt a more liberal policy in the publication of their reports. The increasing usefulness of the geologist to the mining profession in recent years demands that consideration be given to this question. Prior to 1900, the call for geologists of high reputation by mining companies was probably mainly in connection with lawsuits arising from the interpretation of rights or ownership as defined by the "Law of the Apex," and from problems such as finding the continuation of the vein or whether the vein followed was the main one or a branch. Later, outside of legal questions, the most intensive and general use of their services arose from the search for oil. Geologists to determine the position of the formations

Jan 1, 1938

By Walter W. Focke, Zola Kwela, Willem van der Merwe, Arao Manhique

"The advantages of the de Wet zirconium process for the manufacture of AZST from zircon sand include: Fewer processing steps; removal of radioactivity by leaching rather than by precipitation; alkali reagent recovery in the form of a sodium silicate solution that is essentially free of radioactivity; fewer waste streams and less waste to discard.Here we report on our efforts at maximizing the alkali recovery in the sodium silicate product stream: Milled zircon, d50 ˜ 9 µm, was fused with caustic soda pearls in open reaction vessels at temperatures between 650°C and 850°C. Fusion times of 1, 2, 4, 24 and 336 hours (with intermittent milling) were investigated.For prolonged fusion times the fusion products approached equilibrium compositions. However, the phases Na2ZrSiO5 and Na4Zr2Si3O12 observed at 850°C did not form at 650°C. Since they do not hydrolyse in water they limit the recovery of alkali. For 2-hour fusions a broad spectrum of non-equilibrium reaction-products, that are rich in sodium silicates, is formed. Optimum process conditions, with respect to NaOH recovery, correspond to a 2:1 stoichiometry and fusing for 2-hour at 850°C. At these conditions the alkali recovery is ca. 78% and the zirconia yield is ca. 57%."

Jan 1, 2003

The Bureau of Mines, U.S. Department of the Interior, devised a flotation technique for upgrading chromite in chromium ores and gravity concentrates. The technique consisted of cationic flotation of chromite from a slime-free pulp acidified to pH 2.5 or lower using H2S04 modifier. Flotation results showed that ore containing serpentine as the primary gangue mineral was more amenable to concentration by this technique than ore containing the readily floatable olivine as the primary gangue mineral. Rougher flotation of a chromite ore containing abundant serpertine increased the grade form 19 to 41 percent Cra03 at a chromite recovery of 89.6 percent. Rougher flotation of ore containing abundant olivine upgraded the chromite from 23.4 to 29.6 percent Cr203 at a recovery of 89.4 percent. The technique was also applied to chromite gravity concentrates to further upgrade chromite and to reject silicates. Flotation of a gravity concentrate containing 40.9 percent Cr203 and 4.4 percent SiO2 recovered 90 percent of the chromite in cleaner products containing 44.9 percent Cr203 and 0.63 percent Si02. The combined recovery by gravity and flotation was 87 percent. An economic evaluation of this technique will be undertaken to deter-mine its feasibility for commercial use.

Jan 1, 1980

By D. P. Patil, B. K. Parekh

Water is the mainstay for beneficiation of fine size coal and minerals; however, it is also the least desirable constituent in the final product. The basic concept of the novel process described in this paper is based on the differential surface heat conduction/ absorption capacity of individual particles, which differs for different species of minerals. When a mixture of fine material is exposed to a radiant energy source, the various solids present in the mixture will absorb heat energy depending on their heat-conducting properties and there will be a difference in the surface temperature of the particles. When this differentially heated solid mixture is placed on a moving belt, which is coated with a low temperature melting resin, the hotter component of the mixture will stick to the belt and relatively cooler particles will stay free on the belt and fall off at the end of the belt run. Experiments were conducted with pyrite, coal, and quartz of 6 × 18 mesh particle size. The goal of the test program was to find the optimum conditions at which there exists a required temperature difference between minerals and coal particles by controlling the operating system variables. Preliminary tests results showed that there is a potential for separating mineral matter from coal using the thermo-adhesive separation technique.

Jan 6, 2022

By Natalie A. Sapola, Knox Van Dyke, Jean Rabovsky, Vincent Castranova, William H. Pailes, Melanie McPeek, Deloris J. Judy

"INTRODCJCTJONPlatelet activating factor (PAF) is a glycerophospholipid (1-0-alkyl-2-acctyl-sn-glycerol-3-phosphoryl choline) which has been shown to mediate a broad range of biological activities. 1·3 Its pulmonary actions include contraction of pulmonary tissue,4 secretion of leukotrienes from leukocytcs,5 airway constriction,6 pulmonary edema,7 and enhanced migration of neutrophils into the airspaces of thelungs.8-9PAF can be released from several different cell types, such as, basophils, neutrophils and alveolar macrophages, in response to a variety of particulates or membrane stimulants which include zymosan, calcium ionophore, phorbol esters, chemotactic agents, and endotoxin. 1~1 3 Therefore, PAF may play an important role in the development of pneumoconioses by mediating pulmonary responses of lung cells to a variety of occupational dusts. To investigate this possibility, we determined the effects of P AF on several physiological parameters of neutrophils, alveolar macrophages, and alveolar type Il epithelial cells.METHODSIsolation of CellsNeutrophils were isolated from human blood by dextran settling and centrifugal elutriation.14 Isolated neutrophils (93% pure) were resuspended in HEPES-buffered medium (145 mM NaCl, 5 mM KCI, 10 mM HEPES, 5 mM glucose, and 1 mM CaC12; pH = 7.4). Cell number and volume were determined with an electronic cell counter equipped with a sizing attachment.Rat alveolar macrophages were obtained by pulmonary lavage with ea2+, Mg2+-free Hanks balanced salts solution. 15 Alveolar macrophages (94% pure) were resuspended in HEPES-buffered medium, counted, and sized electronically.Rat alveolar type Il cells were isolated by enzymatic digestion for 35 minutes at 37°C with 40 µ/ml type I elastasc and 0.1 % collagenase and purified by centrifugal elutriation. 16.17 Type Il cells (92 % pure) were resuspended in HEPES-buffered medium for measurement of membrane potential, oxygen consumption, and trypan blue exclusion. Type Il pneumocytcs were resuspended in 0.1 M NaCl plus 0.05 M HEPES (pH = 7.8) to measure cytochrome P450-dependent activities and aggregation. Cell size and number were determined electronically."

Jan 1, 1990

By M. Lundström, J. Aromaa, S. Seisko

"Gold dissolution was investigated in ferric chloride media, promoted as one of the most promising alternatives for cyanide-free gold leaching. The characteristics of gold open circuit potential (OCP) and its relation to gold dissolution rate was investigated. Furthermore, the reaction mechanism of gold dissolution in ferric chloride leaching was discussed. The effect of solution variables, [Fe3+] = 0.02–1.0 M, [Cl–] = 2–5 M, T = 25–95 °C and pH = 0–1.0, on OCP and dissolution rate were studied electrochemically using rotating disk electrode (RDE) and linear polarization resistance (LPR) method with ?cyc = 1000 RPM. The investigated gold OCPs in ferric chloride solutions were found to vary between 597 and 688 mV vs. saturated calomel electrode (SCE) and gold dissolution rates between 1.2·10–5–5.0·10–4 mol s–1 m–2. Increase in temperature (25–55 °C) and ferric concentration (0.02–1.0 M) changed OCP into more positive values, while increase in chloride concentration (2–5 M) decreased it. The logarithm of gold dissolution rate was shown to increase linearly with increasing OCP at the temperature range 25–95 °C, ferric concentration range 0.02–0.5 M and chloride concentration range 2–4 M. A notable increase in the gold dissolution reaction rate was evident at T > 55 °C. INTRODUCTION Currently cyanide leaching is the predominant method used in gold production from primary raw materials (Marsden and House, 2006). However, since the Baia Mare disaster in Romania in 2000, the use of cyanide has been the subject of international concern due to the toxic nature of the chemical posing a significant health threat if exposed to the ecological entities (Hilson and Monhenius, 2006; UNEP/OCHA, 2000). Therefore, several countries e.g., Costa Rica, Czech Republic, Germany, Hungary, Turkey, many states of the USA and provinces of Argentina, have started to ban or limit cyanidation via legislation (Laitos, 2012). Thus, alternative solutions, such as thiourea, thiosulphate, oil-coal agglomerates as well as halides have been investigated in order to replace cyanide as lixiviant (Adams, 2016; Aromaa et al., 2014; Aylmore, 2005; Hilson and Monhemius, 2006; Lampinen et al., 2015). Ferric and cupric chloride leaching have been reported to have advantage over cyanidation being capable to dissolve refractory gold minerals, without pre-treatment such as pressure oxidation or roasting (Angelidis et al., 1993; Lundström et al., 2014; Marsden and House, 2006; van Meersbergen et al., 1993). According to Aylmore (2005), 4% of publications for alternative lixiviants to cyanide in gold leaching were within category oxidative chloride processes including aqua regia and acid ferric chloride leaching. Further, some patents have been granted for ferric chloride leaching of gold (Abe and Hosaka, 2010; Lundström et al., 2016)"

Jan 1, 2018

By Antoine Allanore, Luis A. Ortiz, Donald R. Sadoway

"The steelmaking industry has drastically reduced its energy consumption in the last fifty years, and today’s technologies are considered to operate at their optimal efficiency with respect to energy needs. To cope with new constraints related to greenhouse gas (GHG) emissions, a change of paradigm is necessary. One of the promising technologies that could be deployed to help reach CO2 mitigation targets relies on the intensive use of electricity: molten oxide electrolysis (MOE). This paper presents the key process parameters that need to be tuned to address the practical needs for both high productivity in a steelmaking reactor and for an energy efficient process. Herein we show that contrary to common perception, the electrolysis process for ironmaking requires less energy than today’s chemical reduction route. Furthermore, we prove that most of the energy that must be provided to operate the electrolytic iron production cell is thermal energy which is readily generated by joule heating during electrolysis due to large currents being passed through the electrolyte. The energy consumption of the electrolysis cell is therefore shown to be highly dependent on the cell configuration and the chemistry of the electrolyte. As a consequence, the CO2-impact of the technology strongly depends on both the power production mode and the technological choices for design of the process, including cell configuration. Surprisingly enough, even when the electricity generation is not carbon-free, MOE still appears to be viable from the perspective of reducing GHG emissions providing sound reactor design considerations are made.IntroductionIn the context of greenhouse gas (GHG) emissions mitigation, the steelmaking industry is considering several techniques that could sustain the efforts and progress achieved by this sector in the last decades [1]. A recent report [2] on potential routes for low-CO2 steelmaking highlighted for all techniques both the strong dependency of CO2 emissions on electric power production mode and the need for a decrease in energy consumption per tonne of steel. Incited to innovate with respect to this last criterion, the steel industry considers electrolysis to be a promising technological solution, and in particular the molten oxide electrolysis (MOE) process. This process conducts electrolysis in a mixture of oxides that dissolve the iron oxide feed, which by the action of electric current is decomposed into liquid iron and oxygen gas. The opportunity for reduction in energy consumption during steelmaking by MOE is commonly attributed to the “direct” pathway from iron oxide to liquid metal offered by the use of a molten oxide melt and operation at a temperature above the melting point of iron, ideally 1600°C, to provide enough superheat for tapping the molten iron product:"

Jan 1, 2011

By A. Wahab Khair, Richard D. Begley

"This paper presents results of destructive tests performed on rectangular coal specimen under the influence of two vertical and simultaneous wedge indentation forces. Several wedge designs and spacings were utilized in compression tests. The objective of these experiments was to qualitatively monitor the effect of different wedge designs and spacings on the stress distribution within the coal specimen.Coal samples from the Waynesburg coal seam were cut and trimmed to cubical dimensions of approximately 5 X 10 X 20 cm. These specimen were subjected to parallel compressive forces through two vertically applied wedge indentors. Loading was achieved with a hydraulic hand pump in order to facilitate interferogram construction. The load increments were limited due to the sensitivity of the holographic interferometric technique (holometry) in measuring small displacements; therefore, interferograms were taken only during similar increments in order to allow for a qualitative comparison between different wedge design and spacings. In some cases, interferograms were taken immediately before and after failure of the specimen.Introduction Failure Modes Three distinct modes of failure occur when geologic materials are subjected to wedge indentation forces. As shown in Figure 1, a crushed zone is located immediately adjacent to the indentor while chipping can occur if the fractures initiated in the crushed zone extend upwards to the free surface.. The third failure mode is a zone of intricate frac¬tures located between the crushed zone and the chipping zone. Several experiments have been conducted over the years to better understand crater formation and stress distribution within geologic materials under the influence of an indentor. Generally speaking, crack initiation and propogation observed in these experi¬ments correlate fairly well with wedge indentation theory; however, the nature of the .fractures is greatly influenced by different material properties such as grain size and cleavage planes. In other words, a wide range of behavior has been found in different rocks subjected to wedge penetration. For example, it has been observed that some rocks are merely crushed and indented while others are more prone to cracking and chip formation. Therefore, the development or nondevelopment of chips depends mostly on wedge geometry, rock type and depth of penetration. This work is part of the study associated with opti¬mization of cutting parameters, which is best modeled by using brittle materials and subjecting them to rigid wedge penetration tests."

Jun 1, 1988

By Graham J. C. Carpenter, Marc Charest, Jason Lo

"The method of producing magnesium-based composites with silicon carbide (SiC) particulates embedded in the matrix of magnesium AZ9I D alloy by the squeeze-casting technique are described. This method involves the fabrication of a SiC particulate preform and the subsequent squeezing of molten magnesium into the preform. In this study, alumina, aluminum phosphate and a proprietary binder were used for the fabrication of SiC particulate preforms. The procedures employed in the fabrication of SiC! AZ9ID composites are presented, together with the results of characterization of the composites using optical and transmission electron microscopy. Special attention is given to the reaction products in the bulk alloy and at the interfaces between SiC particles and the AZ9ID matrix alloy.1. IntroductionInterfacial, microstructural and metallurgical characteristics play an important role in determining the mechanical properties of a composite. In theory, reinforcing magnesium with SiC particulates should provide an improvement in strength and modulus of the composite over the unreinforced counterpart. However, many factors resulting from the fabrication process can cause degradation rather than improvements to the mechanical properties. In particular, the interfacial characteristics are known to critically influence the properties of composites [1]. Before evaluating the mechanical properties of a composite, it is always useful to examine the microstructure, which is closely related to the mechanical behavior. This helps to reduce the labor-intensive steps of sample preparation for mechanical property evaluation, which can be particularly difficult as a result of the high hardness of composite materials, as well as providing a wealth of information on the microstructural and interfacial characteristics, particularly the reaction products caused by processing. This information is also pertinent in understanding the factors governing the mechanical properties of the composites.There are many factors which determine the nature of the interfacial characteristics of a SiClMg composites. Qualitative estimations of the interfacial bonding have been performed based on thermodynamics, electronic and electrostatic concepts. In addition, the kinetic conditions during the fabrication play an important role. From an interfacial energy standpoint, the driving force for the formation of a metal/ceramic interface is the decrease in free energy that occurs when intimate contact is established between metal and ceramic surfaces. The simple representation of the energy change per unit area of interface formed (~G) is given by Dupre equation [2]:"

Jan 1, 1996

"Dry crushing trials at pilot scale have shown that the IMPTEC Super-fine Crusher has the capacity to generate ultra-fine products from hard mineral assemblages presenting at either coarse or fine feed sizes. The super-fine crusher was introduced at the 27th International Mineral Processing Congress in Santiago Chile, with results from a range of duties, which demonstrated the crusher’s potentially expansive operating scope. This paper focuses on current preparations to progress the technology from pilot scale to commercial scale within a concrete production plant, where lead blast furnace slag will be crushed to ultrafine sizes to generate an active silica product for use as a supplementary cementitious material, which can replace Ordinary Portland Cement. A key objective of the operation is to demonstrate an economical route to reducing the cost of concrete production, improving concrete quality and reducing greenhouse gas emissions. The paper also highlights the potentially key contribution super-fine crushing can make to the long-term viability of iron ore beneficiation by simplifying comminution flow-sheets and reducing operating costs. There is every indication that the technology has the potential to feature universally in metalliferous and industrial mineral flow-sheets. INTRODUCTIONToday’s IMPTEC super-fine crusher is the successful end product of development work over 19 years and is the third particle size reduction device conceived, built and tested over that time. The concept evolved as engineering design progressively developed a mechanism capable of harnessing a highly efficient combination of fundamental particle breakage mechanisms. Early development trials at pilot scale indicated that super-fine crushing had the potential to establish a wet or dry, media free, low energy route to ultra- fine products from hard mineral assemblages. Having achieved some impressive results from open circuit pilot tests on fly ash and granulated blast furnace slag it became clear that the cement industry may well provide opportunities to apply the technology commercially. Following expressions of interest from local cement and concrete plant operators, IMPTEC negotiated an agreement to undertake commercial trials with a SFC 350 super-fine crusher installed on site at a concrete supply plant in South Australia. Super-fine crushing scope was recently expanded following further expressions of interest from research groups involved in the processing of iron ores. Pilot trials are progressing in these areas."

Jan 1, 2016