Search Documents

By R. Chen, K. Xia

In deep mining activities, blasting induced compressive stress wave would be reflected as tensile wave at a free surface around the openings, which would facilitate the tensile failure of the deep rock since it is much weaker in tension than in compression. It is thus critical to understand the dynamic tensile failure of rocks subjected to static tension for deep rock engineering applications. A modified split Hopkinson pressure bar (SHPB) system is adopted to load Brazilian disc (BD) samples statically, and then exert dynamic load to the sample through stress wave generated by impact. The pulse shaper technique is used to generate a slowly rising stress wave and thus to facilitate the stress equilibrium of samples during each test. Five groups of Laurentian granite (with tensile strength of 12.8 MPa) BD samples under the pretension stress of 0 MPa, 2 MPa, 4 MPa, 8 MPa, and 10 MPa are tested under different loading rates. The result shows that the dynamic tensile strength of the rock decreases with the increase of pre-tension stress, which is easy to understand because pre-tension stress weakens the rock sample. It is also observed that under the same pre-tension stress, the dynamic tensile strength increases with the loading rate, revealing the so-called rate dependency that is common for engineering materials. Furthermore, it is found that the loading rate sensitivity of the rock increases with the increase of pre-tension stress. A qualitative explanation for this phenomenon is that more microcracks are generated and activated under higher pretension stress, resulting in a more viscous material. Based on the results, an empirical equation is proposed to fit the data and explain the dynamic tensile behaviour of rock under pre-tension stress. A physical model is used to simulate the dependency of the dynamic tensile strength of rock on the pre-tension stress and the loading rate, which is shown to be in good agreement with the experimental results.

Jan 1, 2015

By L Yang, L Chen, E Hu, D Tang

Online monitoring of particles cumulative percent passing (PCPP) for a target size at hydrocyclone overflow, compared with traditional offline methods, provides PCPP feedback in real time, and is advantageous in enabling energy-efficient comminution, increasing downstream flotation efficiency, and improving upstream resource knowledge. However, existing online approaches are generally costly and bespoke, and some are sensitive to operational changes. Therefore, this study proposes a new low-cost alternative based on accelerometer measurement for online PCPP monitoring in the overflow of hydrocyclones and provides a preliminary experimental investigation under dry condition. The proposed method uses a sensing probe inserted into the overflow pipe of a hydrocyclone to receive particle impact from the incoming slurry, with accelerometers attached to the probe and mounting frame outside the pipe for particle-probe impact detection. As a preliminary investigation before studying particle-probe impact events in slurry, tests under dry condition without fluids were conducted using dry sand particles in free fall from a fixed height. Accelerometer measurements are analysed in both time and frequency domains through root-mean-square (RMS) and fast Fourier transform (FFT). Results show that accelerometer measurements are useful in estimating mass flow rates, which are correlated to the accelerometer output amplitude RMS values in time domain, in a non-linear mapping. Different particle size classes can be identified by examining the accelerometer output amplitude at a known mass flow rate. Different particle size classes feature their distinct signature frequencies (SFs) that can be examined via FFT and the SF is found to be independent of the mass flow rate. The results imply that any PCPP changes can be detected by the change in the accelerometer output amplitude as well as a shift in SF, which demonstrates the effectiveness of using accelerometers to gauge changes in PCPP. Based on the current findings in dry condition, future work will investigate particle-probe impact events in slurry.

Aug 24, 2022

By J. E. Dutrizac, J. B. Sunstrum

Until relatively recent times, virtually all gold was recovered by gravity and/ or amalgamation methods. Although such techniques are very effective on coarse gold, they become increasingly less useful for finer grains especially when the gold is partly enclosed in rock matrix. Throughout the nineteenth century a number of bonanza gold fields were found in the United States, South Africa, Australia and Canada. In every case the abundant supply of gold nuggets and coarse alluvial gold soon gave way to hard rock mining with its inevitable losses of fine gold in the stamp mill tailings. Continuing efforts to develop new technologies capable of dissolving gold from finely ground ore were eventually successful first with chlorination (the Plattner process) and subsequently with cyanidation. Even before the nineteenth century, however, European chemists such as Scheele and Berthollet were aware that gold could be readily dissolved in an excess of free cyanide(1). As early as 1840, a patent was issued to the Elkington brothers for the dissolution of pure gold in cyanide solution and its subsequent plating onto various metals, with or without an applied electrical current. In 1846, Elsner showed that oxygen was also required to solubilize gold or silver in cyanide media(1). Despite the fact that much work was done on the reaction of cyanide solutions with gold, a viable leaching process for gold ores did not quickly emerge although cyanide solutions were used to enhance amalgamation from the 1860s onward. Major problems were associated with the use of concentrated cyanide solutions; the costs of cyanide were excessive and it was difficult to recover gold from the concentrated media.

Jan 1, 1999

By Charles Will Wright

MINERAL production in almost all European countries suffered a sharp setback because of the war. Plants were damaged, transportation facilities disrupted, and labor dispersed and demoralized. Since the war, due to lack of confidence and economic stability, there has been little incentive to rebuild and expand the mineral industries even though a big demand at high prices exists for mineral products. Most mining and metallurgical companies in Europe hesitate to invest their capital because of the tendency towards nationalizing industry, high taxes, and low output of labor, as well as the deficiency of mine supplies and equipment within their countries. In short, they do not have faith in the future, and for these same reasons and fears most of the mining companies in America will not risk capital investment in Europe. In Europe, including the United Kingdom, free enterprise has been losing ground and as a result the foundation of their economic welfare is being undermined. American mining interests willing to take the initiative could help in counteracting this influence if a way were found for them to co-operate with the European producer without too great a risk.

Jan 1, 1948

By M. E. Tyrrell

Research objectives were to determine the reasons for erratic behavior of semisilica horizontal zinc retorts in service; to investigate potential corrective measures including the possible utilization of more refractory materials in the retort body; and to delineate laboratory tests suitable for process control in the manufacture of retorts. Correlation of laboratory test results and data supplied by the cooperating smelters indicated that structural failures due to thermal shock and laminations in the retort body are largely responsible for the erratic behavior of horizontal zinc retorts in service. The most promising modifications made in the retort body and evaluated on a laboratory scale included finer grinding of the plastic clay fraction, substitution of mullite grog for calcined fire clay and grain alumina for silica, plus the use of an organic binder. Lamination-free extrusions having excellent thermal shock resistance were prepared from a mixture composed of 50 percent low-silica Missouri plastic clay through 100 mesh, 25 percent mullite grog through 6 mesh, and 25 percent alumina through 100 mesh. The mix was pugged under 28-inch vacuum with 1 percent ligno sulfonate binder in 12 percent tempering water. Laboratory tests suitable for process control in the manufacture of retorts are described.

Jan 1, 1969

A symposium on pneumatic transportation of solids was held at Morgantown, W. Va., October 19-20, 196'), under the cosponsorship of the Institute ref Gas Technology. Chicago, Ill., and the Bureau of Mines. Objective of the symposium was to present information on developments and projected programs in the technology of feeding, transporting, recompressing, and utilizing gas-solids mixtures Dr. Henry R. Linden, Director, Institute of Gas Technology and Harry Perry, Director of Coal Research, Bureau of Mines, in the initial addresses at the symposium welcomed more than 140 representatives of industry, educational institutions, and government from 16 states, Canada, Great Britain, etc.

Jan 1, 1966

By E. D. Gardner

This paper is the second of a series of three on placer mining in the western United States. The first paper4 discusses the history of placer mining in the Western States and the production of placer gold, geology of placer deposits, location of placer claims on public lands, sampling and estimation of gold placers, and classification of placer-mining methods, together with hand-shoveling and ground-sluicing. This paper deals with hydraulicking, sluice boxes and riffles, recovery of gold and platinum from placer concentrates, treatment of amalgam, and marketing of placer gold. The discussion of sluice boxes and subsequent subjects in this paper applies to all forms of placer mining. The third paper deals with dredging and other forms of mechanical handling of placer gravels, and drift mining.

Jan 1, 1934

A symposium on pneumatic transportation of solids was held at Morgantown, W. Va., October 19-20, 1965, under the cosponsorship of the Institute ref Gas Technology. Chicago, Ill., and the Bureau of Mines. Objective of the symposium was to present information on developments and projected programs in the technology of feeding, transporting, recompressing, and utilizing gas-solids mixtures. Dr. Henry R. Linden, Director, Institute of Gas Technology, and Harry Perry, Director of Coal Research, Bureau of Mines, in the initial addresses at the symposium welcomed more than 140 representatives of industry, educational institutions, and government from 16 states, Canada, Great Britain, etc.

Jan 1, 1966

By Reinol Compañero, Ivy Gonzales, Herman Mendoza, Brian Buenaventura

"The extraction of gold in the Philippines has been a significant challenge for the past decades. Around 70-75% of gold mined in the country can be accounted from the small-scale mining industry which primarily use the traditional cyanidation and amalgamation; processes which have been advocated due to its adverse affects to health and environment. To address this challenge, an alternative clean and sustainable technology was developed for the small-scale miners to recover gold and other metal/mineral values efficiently from Philippine ores. An initial survey was conducted and followed through with extensive mineralogical investigations ascertain the best method applicable. It was determined that Philippine gold occur in ore as (1) very fine particles in the microns range, (2) free-milling, which is in abundance, and (3) locked particles with sulfides --- it was concluded that enhanced gravity concentration and flotation are viable alternatives. A comprehensive test regime was followed to check the response of the ores obtained from different small-scale mining districts across the country. It was shown conclusively that the gold ores respond positively, with recoveries using gravity concentration and flotation of at least 95% and 88%, respectively; exceeding the nominal recoveries using cyanidation or amalgamation. A specific process flow was designed for each type of ore with customized parameters. It was determined that while capital expenditure of implementing these alternative processes is higher than what is currently being used, the operational aspects show that it is much more economical to apply enhanced gravity and flotation. It should be noted that the process developed addresses the critical issue of environmental costs which should be more than enough to justify the shift from the current to the novel and sustainable technologies."

Jan 1, 2014

By W. E. Newton

THE following notes are offered primarily to show that industrial minerals or their products have a much more important place in the metallurgical industry than is perhaps generally realized, and with the hope also that some statement by the metallurgical consumer of the relative merits of various materials for particular requirements or services will l;>e of value to the industrial mineral producer. These notes are not in any way presented as complete. Also, some of the statements made may be debatable. The grouping adopted is as follows: (1) Refractories; (2) Fluxes; (3) Construction materials; and ( 4) Miscellaneous applications. Fuels are not dealt with in the present paper. REFRACTORIES GENERAL: Refractories are materials which will withstand high temperatures with-out melting or becoming markedly soft or pasty. While their primary function is to withstand heat, they are usually called upon to resist one or more of the following destructive influences: abrasion, pressure, corrosion by slags or fluxes, and rapid changes in temperature. Refractory materials may be conveniently divided into three classes: (1) Acid refractories-consisting of silica, or containing silica as their chief constituent. They combine more or less readily with metallic oxides, forming silicates, and are hence termed 'acid'. The most important of these are quartz, quartzite, siliceous sand, tripoli, Dinas rock, and ganister. Most fire-clays, although generally considered neutral sub-stances, contain relatively small amounts of free silica and are, to that extent, acid. (2) Neutral refractories-the term is merely relative in most cases, since, at high temperature, many of the refractories that are classed as neutral will react chemically with a strong base, functioning as a weak acid; or, conversely, with a strong acid, functioning as a weak base. Chrome and graphite are the most nearly neutral of all the commonly used refractory materials.

Jan 1, 1936

By E. Lee

With the growing environmental concern, as well as the increasing concern for sustainability of natural resources, the need of improving the performance and efficiency of today?s crushers is be-coming increasingly important. However, the development of existing crushers requires an extended basic knowledge about the crushing process itself. The aim of the present study is therefore to find the theoretically optimal way of crushing compressively under given circumstances. In the present paper, optimizations have been performed with the purposes of maximizing product yield and minimizing energy consumption. Performed on an ideal crushing stage free from physical limitations, the optimization results have been obtained in terms of number of compressions and their corresponding compression ratios. Complementing earlier results on interparticle breakage (Hulthén et al., 2006), presented here are thus the results from corresponding optimizations with single particle breakage and interparticle breakage. It is concluded that modern crushers are not working optimally in any of the studied aspects for gneiss. In fact, optimizations indicate that a lowering of the compression ratio, as well as a shortening of the crushing sequence, are theoretically favourable. The outcome of this study is therefore highly promising as to giving new ideas and suggestions of improvements in existing crushers, and can even result in redesign of compression crushers.

Jan 1, 2014

By A. Perillo

The process, realized in. the Kivcet furnace, can convert continuously lead concentrates, residues and secondary lead bearing materials into a lead bullion free of sulphur and a discardable slag. The lead recovery can be up to 99%. The long experience of about three years at Portovesme demonstrates the capability of the furnace to smelt a very. high range of lead raws without interruption of the operation. The operating costs are very competitive in comparison to the traditional technology. The work place and environment are clean and new tight regulations for the? hygiene control are met. The Kivcet furnace can be considered as consisting of three parts (reaction shaft, waste gas shaft and electro-furnace) connected with a common hearth. The technical basis of the furnace construction is the application of a number of design elements .which have mostly been used before in designs of industrial furnaces, such as open hearth furnace, refining furnace and other furnaces dealing with liquid meta1s. Refractory wear in the reaction shaft with typical pattern from watercooling soon has been stabilized and since maintained. No deformation of the furnace shell and no leakage of metal or s:l:ag through the bottom is? appeared after three years' operations.

Jan 1, 1990

By M. H. Kersten, G. A. Brady, Jerry W. Ramsey

Anthracite samples were oxidized with nitric acid to prepare products representing intermediate stages of oxidation . Similar oxidizing conditions affected different anthracites to varying degrees as characterized by peptization behavior with 0.1 N NaOH . Techniques used in attempts to separate and characterize the products included esterification , absorption spectrophotometry , sublimation , chromatography , electrophoresis , metal salt formation , and solvent extraction . Mellitic acid , either free or in the form of metallic salts , was identified in the acid- soluble products from 10 tests in which the anthracite was treated with nitric acid for periods varying from 24 to 1,000 hours . pentacarboxylic acid was also found in some products . Other benzene carboxylic acids were not present in amounts detectable by the methods used in this study . The acid- insoluble residue from nitric acid treatment varied significantly in solubility behavior toward different classes of solvents . The most effective ones tried included polar oxygenated solvents and pyridine . Infrared spectra of the extracted material indicated that similar compounds were extracted by the different solvents . Aliphatic amines and aniline peptized the residue and o- toluidine reacted with it . Organic material separated from the residue by peptization with dimethylformamide contained 1 percent ash , consisting of more than 50 percent zirconium .

Jan 1, 1964

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous .sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1958

By Jaffrey Y. Foley

Placer gold and platinum-group metals (PGM) In the Slate Creek area, northern Chistochina Mining District, are derived from silicified and carbonate-altered, Cretaceous-Tertiary (?) dikes and related mafic and ultramafic rocks. Gold In the placer deposits is also derived from Tertiary conglomerate and altered Jurassic-Cretaceous argilllte. The argilllte and Igneous bedrock sources show a unique Ag-Au-Cu-Hg-PGM association that Is attributed to a combination of magmatic, hydrothermal, and supergene processes. The bedrock and placer deposits contain a variety of gold silver-lead-copper and PGM alloys. The observed geochemical, mineralogic, and alteration features are consistent with current geological models for turbidite-hosted gold deposits. No economic gold or PGM lodes were Identified, but several areas warranting more detailed investigation were Identified. Conventional geochemical sampling and analysis of small sample splits weighing between 10 and 30 grams were shown to be unreliable as a consistent means of identifying gold- and PGM-bearing bedrock. Pan concentration of pulverized rock samples was shown to be a more effective, but still Imperfect means of Identifying gold and PGM source rocks. Geochemical data and mineralogic examination indicate that gold and PGM in potential lode sources are very finely and erratically disseminated, are chemically combined with other elements, and may not be entirely free-milling or amenable to simple gravity concentration.

Jan 1, 1990

By Andrea Koschinsky

Numerous hydrothermal vents occur along the Earth?s oceanic spreading axes documenting the reaction of seawater with hot magmatic rocks. The circulation of seawater through the oceanic crust, the interaction with hot rocks in the crust, and the subsequent discharge of hot metal- and gas-rich fluids into the ocean have significant implications for the cycling of material and energy on Earth. Until recently, hydrothermal activity was unknown from the Mid-Atlantic Ridge (MAR) south of the Equator where the MAR is offset by about 1000 km at the St. Paul?s and Romanche fracture zones. During a British cruise in February/March 2005, the first active hydrothermal vent field was discovered on the southern MAR at 5°S. During our follow-up cruise M64/1 in April 2005, the first samples from this vent field were recovered with the ROV QUEST (Univ. Bremen) and analyzed onboard. The high-temperature vent field is situated in a water depth of 2990 m along a line of collapse pits within a large basaltic sheet flow. A diffuse, low-temperature field occurs in a jumbled sheet flow few hundred meters to the east with warm water streaming out of cavities between lava blocks. Here we show for the first time that boiling fluids of ~400°C are emanating from sulfide-bearing vents at a depth of about 3000 m at a slow-spreading Mid-Atlantic Ridge segment. Although this segment is composed of thick basaltic crust, these fluids are dominated by hydrogen relative to methane. Whereas the active chimneys consist of pyrrhotite, chalcopyrite, and isocubanite, the mineral association hematite-magnetite-pyrite occurs in the inactive chimneys suggesting that the fluids became more reducing in present times. The high hydrogen contents and the high temperature of the fluids as well as the change to more reducing conditions are most likely related to a young volcanic eruption event some 300 m east of the hydrothermal field. The presence of hematite and magnetite may indicate that the upflow zone or even the reaction zone at 5°S used to be more oxidized then at other MOR sites, where the hydrothermal fluids are commonly buffered by the pyrite-pyrrhotite-magnetite (PPM) buffer. Consequently, high iron contents and high hydrogen/methane ratios occur in high temperature fluids from basaltic host rocks rather than being restricted to ultramafic host rocks. Faunal communities at the South Atlantic vents largely resemble those from the North Atlantic vents implying that the large Equatorial fracture zones do not inhibit or obstruct faunal exchange along the Mid-Atlantic Ridge.

Jan 1, 2005

Over 500 industrial, academic, and government representatives from Europe, Canada, and the United States attended the first large symposium ever held in this country on fly ash utilization and technology, March 14-16, 1967, at Pittsburgh, Pa. Sponsored by the Edison Electric Institute, the National Coal Association, and the Bureau of Mines, the symposium featured 27 formal presentations by leading reports from the United States and Europe on all major phases of fly ash production, utilization, and research. Representing the three sponsoring organizations were Edison Electric Institute, James D. William- son, The Dayton Power and Light Co.; National Coal Association, James R. Garvey, Bituminous Coal Research, Inc; and Bureau of Mines, Harry Perry. Symposium chairman was John H. Faber of the Bureau of Mines. Gerard C. Gambs, Consolidation Coal Co., addressed the opening session. Moderated by Mr. Garvey, President and Director of Research of Bituminous Coal Research, Inc., the opening session was devoted to a discussion of the nature of the fly ash problem, including availability, specifications, and limitations on its use. Subsequent sessions covered Fly ash marketing, fly ash utilization in concrete and masonry products, specialized uses, and recent developments in basic fly ash research. Others serving as session chairmen were Oscar E. Manz, Associate Professor of Civil Engineering, University of North Dakota; Mrs. Katharine Mather, Chief, Petrography and X-ray Section, Concrete Division, U.S. Army Engineers Waterways Experiment Station; Mr. Williamson, and Mr. Perry.

Jan 1, 1967

By Thomas Fraser, William L. Crentz

"INTRODUCTION Sulfur is a most damaging impurity in many of our American coals. From the older coal industry of Europe and Britain we can apparently learn but little about the problem of preparing and using high-sulfur coal. Although washing has long been established there for controlling ash content, sulfur is referred to rarely, as the important deposits are singularly low in sulfur.On the other hand, widely distributed coal deposits of America differ tremendously in sulfur content. Many of the more extensive beds contain too much sulfur for metallurgical use, and almost everywhere except in the Rocky Mountain and Pacific coast regions sulfur control is at least a potential problem. American coal-preparation engineers are confronted not only with great variations in the total quantity of sulfur in coal but with an intricately varying pattern of the physical and chemical forms in which the sulfur occurs. It must be conceded that the baffling problem of sulfur reduction in coal is as yet substantially unsolved, for there are but few isolated instances in which we have been able to prepare a satisfactory metallurgical fuel from coals containing as much as 2.0 percent sulfur in the raw state.It has been assumed generally that organic sulfur, being chemically combined with carbonaceous matter, is distributed throughout the coal matter and that it remains unchanged in the clean-coal part of the product during washing.Sulfur that may be washed out of the coal is that part that is combined with the iron in pyrite lenticles associated with the coal. In most of our coals it has been found that, besides the visible bands, lenses, and flakes of pyrite, extremely small and even microscopic particles of pyrite 4/ are distributed through the coal matter. Only the free, relatively coarse pyrite particles .are removed by conventional coal-washing devices, and usually most of the sulfur is still left in the product."

Dec 1, 1947

Teleoperation is one method by which an operator can remotely control and monitor a vehicle. The operator monitors the status and progress of the remote vehicle by watching the video transmitted from one or more cameras which are mounted on the vehicle. In the case of an LHD, it will be fitted with three cameras. For a twin-boom Jumbo, four cameras are mounted on the drill, three of which will have remote pan, tilt, 15x zoom, focus and lens cleaning controls. The advantage of teleoperation is that an operator can stand in the drive and send the remote vehicle around a corner, completely out of sight and still clearly see what is happening. This means that an LHD returns with a full bucket and a Jumbo can be operated from a safe distance. Standing in the drive teleoperating vehicles, exposes the operator to passing traffic including the remote vehicle. There are two solutions to this problem. One is to equip the operator with a Nautilus æBuddyÆ jacket which will help to protect them from all vehicles. The other is to move the operator into a safe room or area, away from the fumes, the noise and the traffic. In this comfortable, less stressful environment, the operator will be more productive and less likely to accidentally damage the vehicle. The operatorÆs æsafeÆ room does not have to be a formal control room, it can be any area which has AC or DC power available and is large enough to contain a chair and a 1.5 m x 0.75 m table. The æsafeÆ room can be on the surface or underground, it does not matter to the operation of the Nautilus Equipment. If the LHDÆs, trucks, locomotives, etc are automatically guided from origin to destination, the operator is free to operate several vehicles at a time, performing only those tasks which are too difficult for a computer to do by itself.

Jan 1, 1998

By S. A. G. Poppen, J. Konopka

"Petro-Canada's project investigative and experimental underground work in the Galt coal seam at Kipp, Alberta included the construction of an emergency egress and ventilation raise from surface.The Galt coal seam is 206 m below the surface and covered by 8 m of shale, sandstone and clay beds of the Oldman Formation, 128 m of shale, bentonite beds and sandstone of the Bearpaw Formation, and 70 m of glacial till and basal gravel. Free water was encountered from sand lenses in the glacial till and the basal gravel.Excavation for the ventilation raise was a nominal 2 m diameter and it was lined with a welded, continuous, steel liner of 1.2 m 1.D.Excavation in the glacial till was carried out with a surface bucket drill rig combined with hand mining. Ground support in the glacial till consisted of liner plates and backfill grout. The Bearpaw and Oldman formations were excavated by employing standard raise boring techniques. The individual liner sections of the continuous steel liner were assembled on surface and the entire liner column was lowered into the raise by employing hydraulic lift climbers. The liner column was back-filled with concrete.IntroductionThe Lethbridge Coal Field comprises an area of approximately 1 165 square km in the vicinity of Lethbridge in southern Alberta. Pacific Petroleums Ltd. proposed in a Preliminary Disclosure in January 1979 ""to open an experimental mine prior to development of a producing underground mine with an initial rate of 540,000 tonnes per year"". A 2 900-hectare group of leases in the Kipp-Coalhurst area was selected as the primary target for the Kipp experimental mine. The scope of work for the experimental mine included the construction of an access shaft with production capabilities, the construction of a ventilation and emergency exit raise, drive-ages in coal to yield a bulk sample, gathering of geotechnical information and the testing of experimental mining methods."

Jan 1, 1983