Search Documents

By JOHN W. KOSTER, JAMES R. FLEMING

The following report is made through the Bureau of Mines as a result of the work under the cooperative agreement with the State geological survey and the engineering experiment station of the University of Illinois. It deals with the use of permissible explosives in the coal mines of Illinois, and is intended primarily to present to mining men the possibility of assuring safer conditions in mining through the use of these explosives. Twenty coal mines in Illinois were using these relatively safe explosives at the time this report was prepared. Of these, seventeen were in Franklin County, two were in Saline County, and one in Montgomery County. In these various fields experience had shown that although black blasting powder was a useful agent in breaking down the coal at the working face, yet it had given such conclusive evidence of its danger to life and property in causing explosions and mine fires that a substitute was sought and has been found in permissible explosives. Each coal mine in Illinois in which permissible explosives are used was visited and a study made of the problems involved. The report deals briefly with the dangers of black blasting powder now in such common use in coal mining. It discusses the development of permissible explosives and their introduction into Illinois coal mines and points out the characteristic differences between permissible explosives and black blasting powder. The present system of blasting and the most approved methods of using permissible explosives are described. Data are given to show that not only has safety and efficiency in these mines been greatly improved, but that the cost of explosives to the miner per ton of coal has been reduced, and that sizes of coal produced from permissible explosives compare favorably with those previously obtained at the same mines with black blasting powder. The successful use of permissible explosives in these Illinois mines as well as in many other mines throughout the country should aid in their introduction into a larger number of mines and bring about that degree of freedom from explosions and fires which should be attained in mining.

Jan 1, 1917

By Herbert Hoover

I HAVE been greatly honored as your unanimous choice for President of this. Institute, with which I have been associated during my entire professional life. It is customary for your new President, on these occasions, to make some observation on matters of general interest from the engineer's standpoint. The profession of engineering in the United States comprises not alone scientific advisers on industry but, in great majority, is comprised of the men in administrative positions. In such positions, they stand midway between capital and labor. The character of your training and experience leads you to exact and quantitative thought. This basis of training in a great group of Americans furnished a wonderful' recruiting ground for service in these last years of tribulation. Many thousands of engineers were called into the army, the navy, and civilian service for the Government. Thousands of high offices were discharged by them with credit to the profession and the nation. We have in. this country, probably, one hundred thousand professional engineers. The events of the past few years have greatly stirred their interest in national problems.' This has taken practical. form in the maintenance of joint committees for discussion of these problems and support to a free advisory bureau in ,Washington. The engineers want nothing for themselves from Congress.. They want efficiency in government, and you contribute to the maintenance of this bureau out of sheer idealism. This organization for consideration of national problems has had many subjects before it, and I propose to touch on some of them this evening.

Jan 1, 1920

By S. Vimalnath

The bioremediation capability of Pseudomonas aeruginosa cells was investigated for the biosorption of lead ions from aqueous solution. The various parameters such as pH, kinetics, biomass loading and concentration of lead affecting the biosorption process were studied. Complete bio removal of lead could be achieved for an initial concentration of 12.4 mg/L at pH 6.2, corresponding to typical industrial effluents. The biosorption isotherm followed Langmuirian behavior and the Gibbs free energy (?G) was determined to be-30.8 kJ/mole, indicative of chemisorption between the functional groups of the bacterial surface and lead. The biosorption kinetics adhered to a pseudo-second order model. The possible mechanisms of interaction of lead with the bacterial cells are discussed. A carbon paste electrode with a coating of biomass was developed for lead ion detection in aqueous solution using cyclic voltammetric technique. Concentrations of lead up to 5x10-5 M could be successfully detected using cyclic voltammetry, which could be improved to a detection limit of 1x10-8 M adopting differential pulse anodic stripping voltammetry (DPASV). Keywords: Pseudomonas aeruginosa, bioremediation, lead, voltammetry

Sep 1, 2012

The effect of the acid anion on chalcopyrite (CuFeS2) leaching has been examined, under care-fully controlled conditions, in a range of acids in stirred reactors and columns at pH 1. Solution speciation calculations were performed to determine possible rate controlling species. The relative leach rates of Cu from chalcopyrite can be explained quantitatively entirely on the basis of solution speciation without the need to invoke any rational relating to surface structure/speciation. The rate of Cu release is first order with respect to Fe3+ activity. The stirred batch reactor experiments at fixed pH 1, Eh of 750 mV (SHE) and 75? showed that chalcopyrite leach rates were rapid in both HClO4 and H2SO4 with 100 % Cu recovery after 73h and 97 h respectively. However, the leach rate in H2SO4 was slower as compared to the HClO4 leach due to a slower increase in the activity of Fe3+ due to the formation of FeSO4-. The presence of Cl- in the leaches (HCl and H2SO4 with NaCl added) led to a low activity of Fe3+, due to the high activity of FeCl2+, resulting in very low leach rates. For the column leach experiments dissolution of Fe and Cu from the pH 1 HCl eluted chalcopy-rite column with quartz proceeded at several times the rate of any other column (chalcopyrite with and without quartz and/or pyrite leached with H2SO4, HClO4, HCl). Three observations indicate that galvanic interactions are not leach rate controlling role: a) The rate of leaching was not uniformly increased for the non-quartz containing columns where the two sulfide minerals, chalcopyrite and pyrite, are in physical contact as compared to the analogous quartz containing columns where they are not; b) there exists a reasonable correlation between the rate of Cu release and the effluent Fe3+ activity for all columns thus indicating that the leach rate is determined by solution speciation; and c) in all cases the proportion of Fe to Cu leached indicates preferential dissolution of Cu over Fe. However, the proportion of Fe to Cu is either the same or greater than expected on the basis of the single mineral columns. This indicates that chalcopyrite is not dissolving preferentially to pyrite.

Jan 1, 2014

By Seetharama C. Deevi, Mohammad R. Hajaligol, Sarojini Deevi

"Carbides and nitrides of iron are being considered as magnetic materials for high-density recording due to their chemical stability and high-saturation magnetization values (> 100 emu/g). Iron carbides and iron nitrides with magnetic properties suitable for magnetic media were synthesized by employing a novel synthesis procedure based on fluidization of powders in reactive atmospheres. Fluidized-bed reactors of laboratory, bench, and pilot scale were employed for the synthesis of iron carbide, FeSC2, by reducing and carburizing U-Fe203 in the temperature range of 300 to 550 ºC. A temperature of 400· ºC and a reaction time of 2 to 3 h are found to be optimal for the synthesis of iron carbide. When the carburization was carried out in a reducing and carburizing atmosphere such as carbon monoxide, nucleation and growth of FeSC2 occurred directly from Fe304 with no intermediate phases such as FeO or Fe. Longer carburization times resulted in the deposition of carbon on the surfaces of FeSC2 particles due to Boudouard reaction, and higher temperatures favored the formation of a mixture of carbides such as FesC2 and Fe3C. Iron nitrides were synthesized by reducing u-Fe203 in the temperature range of 350 to 550 ºC, followed by nitriding in the temperature range of 350 to 550·ºC. The powders were characterized using X-ray diffraction, scanning electron microscopy, thermogravimetric analyzer, and a vibrating sample magnetometer.IntroductionRecent demand for high-quality recording of optical, electrical, and audio signals generated interest in magnetic tapes with high-recording densities as compared to the conventional magnetic tapes based on U-Fe203. At present, commercially available magnetic tapes contain maghematite, U-Fe203, as a magnetic material with a saturation magnetization of90 emu/g and a coercive force of 400 Oe. Recording of signals at a higher density per unit volume of magnetic material demands magnetic materials with high-saturation magnetization and a reasonable coercive force. Although metallic iron particles possess a saturation magnetization of 130 to 150 emu/g and a high coercive force of 1000 Oe, the gradual oxidation of iron-to-iron oxides (of lower saturation magnetization) prevents the use of iron particles for high-density recording. In contrast, iron carbides such as FesC2, Fe7C3 and iron nitrides such as Fe4N and Fe3N possess excellent magnetic properties coupled with good electrical conductivities and high hardness. The carbides and nitrides of iron have generated significant interest as magnetic materials for the next generation of magnetic tapes due to their unique magnetic properties and relatively greater oxidation resistance as compared to metallic iron particles [1-4]."

Jan 1, 1994

By N. C. Joughin

A simplified economic model is derived for the financial return from a new gold mining project. The model is used to analyze the effects of changes in the mining rate, capital costs, working costs, value of the reef and the stoping width. The most effective avenues for improving the return from a new project are indicated. It is shown that those technological innovations which would improve the return significantly, and therefore make it possible to open more mines, are the use of smaller mines, means for improving the mining rate to capital costs ratio for smaller mines, planning and control of mines by computer simulation, an improved mine valuation procedure and means for mining at a decreased stope tramming width.

Jan 1, 2014

By W. G. Deeks

CANADIANS are world leaders in marketing metal and mineral products. Noranda Sales Corporation Ltd. is an international metal and mineral product marketing company operating from Toronto and London, England, where it operates a wholly owned sales subsidiary and is a 50% partner in Rudolf Wolff and Company Ltd., a charter member and the largest metal broker on the London Metal Exchange. Noranda Sales employs 97 people, of whom 52 are university trained and professionally competent in international resource product marketing. We market for 19 companies or divisions in the Noranda Group and 39 companies for whom we act as agent, consultant and purchaser of resource production. Our business in 1976 was 1.5 billion dollars carried out in 45 countries and covering 24 products and materials. Today, ownership of most of the mining industry in Canada has transferred back to Canadians, and this is said with the knowledge that a significant part of the Canadian industry has been Canadian owned and managed from its very early days. Noranda Mines Limited is such an example. It was born in 1922 as the result of a copper-gold showing at Noranda, Quebec, discovered by Ed Horne, a prospector, financed with a grubstake by a syndicate mainly composed of New York businessmen. Shortly after the discovery, when the shares of the company had risen, the syndicate was sold to Canadian interests and, since that time, Noranda has been dominantly Canadian owned and certainly Canadian managed. Today, over 90% of Noranda's shareholders are Canadian, who hold an equivalent percentage of the stock.

Jan 1, 1977

By J. Stiksma, R. Kalanchey, M. J. Collins, G. Owusu, R. Raudsepp, K. R. Buban, L. A. Barta, I. M. Masters

This paper describes the results of testwork for the treatment of Ambatovy laterite ore by a pressure acid leach process, with recovery of the soluble nickel and cobalt values as mixed sulphide intermediate by precipitation with hydrogen sulphide, and subsequent refining of the mixed sulphide to nickel and cobalt metals. These process development studies were carried out primarily in 2004, as part of a bankable feasibility study for the Ambatovy Nickel Project. The Ambatovy orebody is located in Madagascar. The mini pilot plant testwork was carried out in the Dynatec metallurgical laboratory in Fort Saskatchewan, Alberta. The results of the testwork were very encouraging, including nickel and cobalt extractions in the range of 95.5% to 97.0%, and 94.0% to 97.0%, respectively, in the ore leach step with sulphuric acid. High recoveries of nickel and cobalt were achieved throughout the remaining process steps, yielding separate nickel and cobalt metal powders with better than acceptable purity.

Jan 1, 2005

By J. Peterson, D. D. Tannant, J. Todd

"A review of blast designs and improved blasting practices at the EkatiTM diamond mine is presented along with the results of three blast-monitoring experiments. Blast monitoring was undertaken to investigate blast damage mechanisms in the mine’s well jointed rock mass. Rock mass damage caused by production, pre-shear and wall control blasts was measured. EkatiTM uses 270 mm holes for production blasting, and 165 mm holes loaded with a decoupled charge for pre-shearing. The production blasts are loaded with bulk emulsion/ANFO blends. The mine plan involves using 30 m double benches. A 30 m high pre-shear is drilled and blasted prior to the production blasting that is done with sequential 15 m benches. This paper summarizes the monitoring equipment and data gathered to date. IntroductionThe EkatiTM diamond mine is located about 300 km northeast of Yellowknife, Northwest Territories, Canada. The mine is a joint venture of BHP Diamonds Inc. (80%) and geologists Charles Fipke and Stewart Blusson (10% each). The EkatiTM mine is Canada’s first diamond mine and BHP is the operator. The mine is accessed by air and by a winter ice road.The first kimberlite pipe mined at EkatiTM is known as the Panda pipe. The Panda open pit mine will have a total depth of 315 m (Fig. 1), a width of about 600 m, and a 50° overall slope. Initial ore production is 9000 tonnes per day.This paper summarizes the pre-strip blasting and the evolution of the production and wall control blast designs from 1997 to 2000. The initial blast designs and the rationale behind subsequent changes that took place are presented along with the techniques currently in use.The paper also briefly presents an experiment done to measure the rock mass response to blasting. Three blasts were instrumented with geophones, gas pressure sensors and time domain reflectometry cables. A brief summary of the instrumentation and data gathered is included."

Jan 1, 2001

By Albert J. Rambosek

The results obtained in a study of the stress conditions existing in a drill bit-point area and in the underlying rock, when the bit was in full but nonpenetrative contact with the rock, are presented. This investigation by the Bureau of Mines was the preliminary exploratory phase of a long-range program of research on rock drilling to establish criteria for the maximum economically feasible rate of rock penetration. The photoelastic technique of experimental stress analysis was the principal method used to obtain the data. Transparent models and transmitted light were employed to investigate patterns in drill-bit models and isotropic materials under the bit when subjected to a concentrated static load. Comparative stress data for anisotropic rock were obtained by the reflective photoelastic technique. Brittle lacquer and an extensometer were used obtain supplementary information wherever substantiating data were desired to check photoelastic results. The zone of maximum shear occurs along an arc near the contact face of the bit. The stress distribution pattern in an isotropic model rock near the area contacted by the bit was nearly a mirror image of that exhibited within a similar areal zone of the bit. The stress pattern in granodiorite specimens was similar, though not symmetric, to the pattern in the isotropic model rock. The asymmetry of the stress pattern in the granodiorite was attributed to the anisotropic characteristics of the constituent minerals of various sizes.

Jan 1, 1963

By Ramsey Hart

MiningWatch Canada is the only national independent civil society organization with an exclusive focus on mining in Canada and Canadian mining companies operations internationally. In 2005, MiningWatch Canada collaborated with other NGOs to develop the Framework for Responsible Mining: A Guide to Evolving Standards. The project was the result of a perceived need by NGOs and retailers, particularly from the jewellery sector, for a framework that would set out environmental, social, and governance standards for the minerals sector ?providing recommendations for retailers and others seeking to source or invest responsibly, as well as regulate and encourage responsible mining practices?. This paper is a reflection on the Framework that examines key areas of concern and notes where the industry norms and expectations of civil society have evolved. The paper focuses on developments in social issues related to the UN Guiding Principles on Business and Human Rights, new initiatives associated with financial transparency, the UN Declaration on the Rights of Indigenous Peoples. The environmental components of the Framework that are revisited are waste management, biodiversity, energy and climate change, environmental assessment, mine closure, mercury and seabed mining.

Aug 1, 2013

By Willard L. Hunter

The Bureau of Mines studied the effect of temperature upon the reduction of chromite by carbon and the relative reducibility of chromites as a function of their composition. Ferric oxide was also studied to provide comparative data. Pellets weighing approximately 1 gram and containing 70 percent ferric oxide, chromic oxide, or chromite and 30 percent graphite were subjected to closely controlled temperatures under a flow of argon for 15 minutes. The amount of CO and CO2 evolved was measured, and the reduced sample was analyzed by X-ray diffraction techniques. The reduction of Fe2O3 was studied over a temperature range of 600° to 1,400° C, while the reduction of Cr2O5 and chromite was conducted from 9000 to 1,621° C. The temperature above which appreciable reduction of Cr203 by graphite took place was 1,125° C. The temperature at which significant reduction started for three of the four chromite samples was approximately the same, indicating that there was concurrent reduction of iron and chromium oxides in the chromite mineral rather than selective reduction of iron oxides followed by reduction of chromic oxide. Rhodesian chromite appeared to dissociate at a lower temperature with concurrent reduction of iron. Based on the temperature at Which chromite was 50 percent reduced in 15 minutes, Transvaal chromite reduced most easily, followed by Mouat, then by Kampersian, and finally by Rhodesian DFC material. Statistical analysis of test results indicated that the ferric iron content of chromites affects their reduction behavior more than any other constituent.

Jan 1, 1966

By R C, K L. Rees, J S. J van Deventer

In contrast with previously published models for the carbon-in-pulp (CIP) process, the model proposed in this paper incorporates film transfer, intraparticle diffusion, simultaneous leaching, preg-robbing, the loading of multicomponent species, and the effects of fouling and changing cyanide levels. The rationale behind this comprehensive model is that changes in fouling and competitive adsorption along a CIP cascade affect the profiles of gold loading. As it is impossible to quantify all these non-ideal factors, a method is proposed whereby an imaginary species is postulated so as to combine all the competitive effects. A plant survey at the Telfer mine has shown that the mass loss due to a gravimetric analysis of the fouled carbon could be used directly to quantify this competitive effect. The degradation and consumption of cyanide along the Telfer CIP cascade enhance the loading of copper on to the carbon, which should be taken into account when modelling the gold profiles. It appeared that the effect of cyanide itself on the loading of gold was negligible compared with its effect on the copper. Evidently much more research is required on this topic in order to optimise CIP operations exposed to constantly changing conditions.

Jan 1, 1998

By S. Vongpaisal, T. R. Yu

"A set of new blast damage criteria has been developed, with special reference to blasthole mining operations, for assessing damage by incorporating the vibration level, rock properties, site characteristics and the effects of ground support systems. The main objective of this work was to provide a database with reasonable accuracy for use in optimizing blast design, numerical analysis and ground control expert system module development.The new damage criteria allow one to estimate the degree of damage to rock structures in terms of a dimensionless parameter defined as Blast Damage Index (BDI). This allows for the description of blast damage in a unified form, and facilitates the development of codes for numerical modelling to express the degree of blast damage universally. A number of field investigations from several stope production and slot opening blasts at a large underground base metal mine were carried out to verify the developed index. The results show a good correlation between the observed damage and the type of damage predicted from the BDI values.Practical measures are also provided for minimizing blast damage in large underground blasthole mining operations"

Jan 1, 1996

By R. W. Stahl

Coal mining has been revolutionized by the continuous miner. This machine has replaced, or has combined into 1, 3 former operations: Cutting, blasting, and loading. During the 25-year period before this machine was introduced, advances had been made in transportation, but the actual "coal getting" remained virtually the same. As frequently occurs, the multiple-purpose continuous miner introduced a new hazard--more rapid liberation of methane. The coal output formerly obtained from 10 to 20 working places might now be obtained from 1. It is true that circulation of air was generally increased; but the bulk of this machine virtually precludes continuous flow of air across the face, where gas may accumulate. Apprehension about this possible hazard led the Bureau of Mines to test face atmospheres during operation; and Report of Investigations 5288, Methane Buildup During Cutting and Continuous Mining Operations (published in 1956), presents proof that real danger may be present in many otherwise well ventilated mines.

Jan 1, 1958

By C. G. Anderson

The treatment of materials for the recovery of the precious metals imposes many processing and environmental challenges. Sunshine Mining and Refining Company has developed hydrometallurgical technology for recovery of values from refractory precious metal materials. At Sunshine, the industrial focus of these processes has been for the direct recovery of silver without cyanidation. However, recent work has indicated that these technologies can provide a means for treating complex, refractory gold concentrates. This will be the focus of this paper. The practice of pretreating ores and concentrates to make them more amenable to cyanidation is becoming more common. Several pretreatment options for sulfide concentrates containing gold include roasting, bio-leaching, direct pressure oxidation and nitrogen species catalyzed pressure oxidation. The industrial use of nitrogen species catalyzed pressure oxidation has been limited to the Sunshine refinery where its focus has been for the treatment of silver concentrates. Much of the reluctance, outside of Sunshine, to use this type of technology may be based on the perception that high costs are associated with using nitrogen species (e.g. nitric acid, sodium nitrite) to leach. Also, the use of nitrogen species catalyzed pressure oxidation on an industrial scale is unfamiliar to most metallurgical professionals. A summary of pressure leaching processes which utilize nitrogen species as a catalyst is presented in Tables 1 and 2.

Jan 1, 1996

By D. Raghavan

In recent years, the environmental issues related to the landfill shortage received considerable importance. Many polymeric solid wastes have high resistivity to chemical and biological degradation, and options are sought by which these wastes can be recycled and reused, or reduced in volume. The present study investigated the biodegradation of polyethylene by Aspergillus niger, and biodesulfurization of rubber by pure and mixed cultures of Thiobacillus thiooxidans and Thiobacillus ferrooxidans. The fungus, A. niger, was found to metabolize portions of polyethylene. Quantitative calorimetric measurements revealed that the amorphocity of the sample decreased during biodegradation. Removal of sulfur from synthetic rubber samples containing 2 to 15% sulfur, was studied in shake flask experiments and the associated oxygen consumption was studied in Warburg respirometers. The mixed bacterial cultures were more effective in the desulfurization of rubber samples than the pure cultures of T. thiooxidans and T. ferrooxidans. The data obtained in these studies may have far reaching consequence for the development of new effective processes regarding the remediation and management of discarded polymeric packaging wastes and car tire rubber materials.

Jan 1, 1993

By A. O. Dufresne

The mineral wealth of pre-Cambrian rocks in Canada has been the subject of much study by geologists and engineers (members of this Institute), particularly so in the past few years, following discoveries of mineral deposits in areas far a part. This interest is well worth sustaining knowing the numerous rich producing mines within the pre-Cambrian formations, and the vast area covered by its rocks throughout this country. The pre-Cambrian has yielded minerals, both metallic and non-metallic; of these a much diversified list could be made. In more than one district we can point to mining as being responsible for the opening up of new sections, attracting a population into regions which otherwise would have remained virgin land of little commercial value. In these pre-Cambrian formations are found the rich copper deposits of Michigan, producing without interruption since 1845, and from which seven billion pounds of copper has been won; while in Minnesota and the adjoining district, at the head of Lake Superior, are mined iron ores which have rendered possible the great steel manufacturing industry of United States, the base of the economic structure of that wealthy country. The pre-Cambrian has given Canada the nickel-copper mines of the Sudbury district, the silver deposits of Cobalt and the gold camps of Porcupine and Kirkland Lake. With all of these our members are familiar; and it suffices to mention them to bring to mind pictures of the wealth and 'the growing population, in a word the importance of mining in?those sections of the country.

Jan 1, 1926

Blasting is an essential component of most mining operations, and is used to reduce the rock mass to a workable size distribution, as well as to create stable openings and pit walls. Frequently, there is little difference between the designs of blasts to achieve these two functions, though more advanced operations have developed different designs for these very different functions. To assist in the appreciation of how blasting practices can impact on the stability of rock openings and pit excavations, this paper reviews the role of high pressure explosion gases on final block stability. It is assumed that the stability of all surface and underground excavations are, to a greater or lesser extent, controlled by the interaction between discrete rock blocks. Typically, these blocks will be defined by either natural, or excavation induced, jointing.

Jan 1, 1999

A revolutionary development in blasting materials has occurred in recent years. Ammonium nitrate, sensitized by the addition of a small percentage of No. (class) 2 diesel fuel or other suitable petroleum product, has been adopted as a low-cost, efficient blasting agent2 in a wide variety of mining, quarrying, and heavy construction operations. Moreover, the ready availability of the component supplies throughout the Nation, together with the ease of formulating them into effective blasting agents, has made it possible for the blaster himself to prepare the mixes at the site of use. Recently, most established explosives manufacturers have begun supplying premixed AN-FO (ammonium nitrate-fuel oil) or a comparable product to various mining operations. However, many individuals and small business establishments are marketing premixed products prepared in facilities that are often poorly constructed and poorly located. Although these blasting agents have partly or wholly displaced explosives such as dynamites in many applications, there are some blasting operations in which the fuel-sensitized ammonium nitrate agents do not appear to be well adapted. As long as the hazards they present are clearly understood and respected, ammonium nitrate-based blasting agents have important safety characteristics when prepared under competent factory control or field-mixed under equivalent close control. This publication attempts to summarize the knowledge of those hazards and to incorporate practical ways to cope with them.

Jan 1, 1963