Search Documents

By F. E. Brantley, D. M. Yergensen, D. A. Martin

Fluidized - bed roasting was investigated as a means of decomposing gypsum and gypsum mixtures to produce a gas rich in sulfur dioxide and a lime or portland cement residue . Ninety- eight percent desulfurization of gypsum in a 10 - inch fluidized- bed reactor took 1.5 hours at an operating temperature between 1,200 ° and 1,225 ° C. A cement- type residue was obtained but had to be refired at 1,450 ° C before mortar prepared from it met the physical specifications for cement .

Jan 1, 1963

By Osvaldo Guilherme Comineli

While the hot cracking of Cu-containing steels is a serious and widely known problem for the industry, the literature reports that copper only slightly impairs the hot-ductility measured in laboratory. A distinction is drawn between hot ductility and hot shortness and the respective cracking operating mechanism involved at the respective range of temperature. The representability of the laboratory assessment of hot cracking of Cu-containing steels by hot tensile tests compared with actual results in industrial practice is discussed. The effectiveness of the variable affecting in each cracking mechanism and respective temperature range, focused in improving the hot cracking assessment of Cu-steels and the relative importance of oxidation will also be discussed. It is concluded that the hot tensile test in argon might be a good simulation if properly interpreted and that the role of oxidation is secondary in causing hot shortness. A schematic diagram for the hot tensile test is proposed.

Oct 30, 2017

By Canterford J. H, Sparrow G. J, Dyson N. F

Pressure leaching of a bulk flotation concentrate prepared from a complex Cu-Pb-Zn sulphide ore was carried out at 150 and 190¦C under 1050 kPa oxygen overpressure in 1 L and 4 L titanium autoclaves to extract zinc, and to obtain residues for smelting tests and leach liquors for purification and recovery of the zinc by electrowinning. Dissolution of 95% of the zinc was achieved at both temperatures. Copper and iron dissolution and the degree of oxidation of the sulphide sulphur to elemental sulphur or sulphate depended on the temperature of the leach. At 190¦C, a jarosite (a basic iron sulphate) was the major iron-containing material in a residue that contained 17% total sulphur. Its formation was associated with dissolution of 18% of the iron. At 150¦C, oxidation of the sulphide sulphur and dissolution of the iron were significantly less. Only 7% of the iron was dissolved and a residue containing 25% total sulphur, present as a lead jarosite, lead sulphate, and elemental sulphur, was obtained. The formation of small pellets of unreacted sulphides coated with elemental sulphur caused problems during the leaching at 150¦C, and also during scale-up from the 1 L to the 4 L autoclave at 190¦C. At 150¦C the concentrate required two stages of leaching to achieve dissolution of over 90% of the zinc. These problems are discussed.

Jan 1, 1989

By Ataç Başçetin, Hasan Çelt, Hüseyin Onur Dönmez, Kürşat Hasözdemir

Phenolic foams, known for fire resistance, show broader industrial potential, particularly in mining, through property enhancements. Adjustments to the formaldehyde-to-phenol (F/P) ratio, bio-based additives like lignin, and nano-silica improve foam strength and thermal stability. Density modifications allow foams to range from flexible, low-density forms to rigid, high-density supports. In mining, enhanced phenolic foams could reduce coal ignition risks by acting as oxygen-blocking barriers. Current findings suggest these foams offer viable, sustainable solutions for safety in hazardous environments. Continued development could make them essential for thermal and mechanical applications under extreme conditions. This paper aims to provide a comprehensive overview of the mechanical characteristics of phenolic foams, current enhancement strategies, and standardized testing methods used to evaluate foam properties.

Feb 1, 2025

By B Darlington, L Sandberg, O Vallati

The D47 and D39 Mechanical Dynamic Extra bolts (D47 MDX and D39 MDX) have been developed in response to the ever-increasing demand from the mining industry for rock bolts with high dynamic capacity. To prove such capacity, Sandvik has performed numerous in situ dynamic testing with the unique Dynamic Test Rig (DTR) (Darlington, Rataj and Roach, 2019; Roach, Rataj and Darlington, 2019). To complement the collection of testing data, Sandvik, in collaboration with the Swedish Research Institute for Mining, Metallurgy and Materials (Swerim) have performed additional experiments in laboratory condition using Swerim’s new drop test rig. This rig utilises a momentum transfer method to apply a dynamic load to the bolt. The sample falls together with the mass until the support beam impacts stationary dampers and the momentum energy is transferred to the bolt. Part of the charged energy is released by the dumpers while the remaining portion is absorbed by plastic deformation and/or displacement of the ground support element. The D47 and D39 MDX bolts have been tested at Swerim’s test facility with different levels of input energy. Six tests were performed at the specification energy of 36 kJ and six tests were carried out with the maximum allowable energy from the facility, ie 44 kJ. The bolts confirmed their dynamic performance absorbing the input energy without failure. The D47 MDX bolt absorbed up to 33 kJ with 150 mm displacement while the D39 MDX bolt absorbed up to 35 kJ with 162 mm displacement. This work will present an overview of the drop test rig at Swerim’s facility and a collection of results of the test performed on the D47 and D39 MDX bolts. The test method and results will be analysed and compared to the tests carried out with the in situ DTR.

Nov 29, 2022

By M. J. Beus, B. Stewart, S. Iverson

Ore-pass hazards are a significant safety problem in US underground metal mines. From 1975 to 1995, nearly 75% of injuries during pulling or freeing of ore-pass chutes were related to falls of broken rock or the use of hand tools. Risk assessment methods are being used to identify the most probable causes of ore-pass failures and analyse the factors that result in malfunctioning or safety reduction. Static and dynamic loads are being measured in the laboratory and by field testing, with data from test ore passes compared with mine data to characterise true system behaviour. Computer modelling using closed-form solutions, finite element analysis and a newly developed particle flow code are being use to predict loads from ore and waste flow and impact. Preliminary results indicate that dynamic impacts may be much less than expected, as a result of damping factors, normal and shear stiffness and mass frictional characteristics

Jun 19, 1905

By J. Chelsey Dawson

In presenting a thesis on this subject it is advisable to explain a few of the reasons for its seeming incompleteness. World progress has brought us to a position where approximations are not only to be condoned, but regarded as absolute essentials. Production in anticipation of demand is always accompanied by mistakes on the part of the producers. Only through trial and sometimes erring hypotheses may there be evolved the true course and theory upon which the steady triumphant march of world-wide industry depends. The average person likes to have everything placed ?before him in a clear and convincing manner. It is the impossibility of doing this which, in many cases, arises to confound the writer on shales. All that one can do is to present, as lucidly as possible, the known hypotheses' and theories on the subject and leave the reader to study and work out the truth for himself. Many theories have been advanced on the origin of oil-shales ; some may be correct in certain instances and not in others; however, the writer will attempt no decision as to which are and which are not correct, but .will merely point out the relative merits of each. The figures given for reserves of oil and shale in different countries are only approximations and give but a rough idea of the true conditions.

Jan 1, 1925

By D. A. Hill

A survey of the literature on ELF and VLF atmospheric noise has been made. Most measurements have concentrated on the vertical electric field and the horizontal magnetic field rather than the vertical magnetic field which is of interest in transmission between horizontal loops. The limited vertical magnetic field data indicates that the vertical component is generally 10 to 20 dB below the horizontal component. Three laterally inhomogeneous earth models have been analyzed for conversion of horizontal to vertical magnetic field. The rough surface model examines surface effects, the inhomogeneous thin sheet model treats volume effects, and the buried cylinder model treats localized man-made effects. All three models predict the possibility of significant conversion from horizontal to vertical magnetic field. A thin sheet model has also been used to examine transmission from a buried magnetic dipole source. It is found that the predicted fields more nearly model the measured data than does the homogeneous half-space model.

Jan 1, 1982

By H G. Poulos

"This paper sets out a simplified approach by which the practical foundation designer can undertake the relevant calculations to satisfy the requirements for deep foundation design in seismic areas. The following matters are dealt with:a. Design issues that should be addressed;b. Pile design for axial loading, including the possible effects of liquefaction;c. Pile design for lateral loading where liquefaction does not occur;d. Pile design for lateral loading where liquefaction does occur;e. Measures to mitigate against liquefaction effects.The paper is a modified version of a paper presented in 2013 to the 19th NZGS GeotechnicalSymposium, Queenstown, New Zealand.1. INTRODUCTIONConsideration of the effects of earthquakes and seismic loadings is an increasingly important aspect of modern foundation design, and most contemporary standards have a mandatory requirement for such consideration. For example, the Australian Piling Code, AS 2159-2009, states that “a pile shall be designed for adequate strength, stiffness and ductility under load combinations including earthquake design actions”. However, the methods by which such considerations can be undertaken are generally not set out in the standards, and many approaches have been utilized, ranging from very simplistic methods to extremely complex computer analyses. Accordingly, there appears to be scope for an approach that is soundly based but which is neither too simplistic nor too complex.Poulos (1989) has suggested that there are three categories of analysis and design, as follows:1. Category 1: empirical methods.2. Category 2: simplified but soundly-based methods.3. Category 3: more comprehensive methods that are soundly-based, and site-specific.The objective of this paper is to set out a systematic but simplified approach which falls into Category 2 above, and by which the foundation designer can undertake the relevant analyses to satisfy the foundation design requirements for seismic regions. Emphasis is placed on methods that do not require “black box” software or which employ complex soil models in which the physical meaning of the parameters is unclear."

Jan 1, 1900

By C. Özgen Karacan

The methane emission rate into an underground mine environment from overburden strata during longwall mining is impacted by reservoir and geomechanical characteristics of the coal measure rocks in the overlying strata, as well as the presence of any coal seam. The reservoir characteristics and how they change during mining potentially affect the performance of gob gas ventholes, which consequently impacts the efficiency of methane control in the mining environment. This study presents reservoir and elastic properties of coal measure rocks in the Lower Monongahela Group in Greene County, southwestern Pennsylvania, of the Northern Appalachian Basin. Since the source of methane in this region from underground mining is located between the Sewickley coal and the Pittsburgh coal, a specific emphasis was given to this interval. Core analyses were performed in the laboratory to determine rock porosity and permeability. Geophysical logging data (gamma, density, sonic) obtained from two exploration boreholes were used for evaluating formation boundaries, shale contents, log porosities, and geomechanical properties of formations. Permeability was also calculated using density-log data and empirical equations and compared with laboratory measurements and slug tests performed in isolated intervals of boreholes. The results presented in this study can be used as data sources for reservoir studies related to the production and control of methane.

Jan 1, 2009

Argentina follows Venezuela and Mexico as the largest producers of crude petroleum and natural gas in Latin America. Argentina 1S practically self-sufficient in fuels, but relies substantially on imports for its supply of copper, iron ore, ferroalloys, sulfur, and fertilizers. Mining activity is limited and is in an incipient stage of growth, considering the country's potential for mining. Most nonfuel mineral output in 1979 consisted primarily of minerals used for construction, while only 9% are other nonmetallic, and 2% are metallic minerals. Argentina is Latin America's major producer of boron minerals and uranium (yellow cake). Mineral exports consist primarily of borates, uranium concentrates, and of late, some tin. These exports have in the past been shipped mostly to Great Britain. London banks have been involved in arranging financing for St. Joe Minerals Corp. IS planned development of the El Pachon copper deposit (see map), and were being counted upon to also back the development of large copper and manganese projects. The following is a review of Argentine mineral production in 1979: (For 1981, the production of boron minerals is put at 167,000 metric tons and uranium at 300,000 metric tons.)

Jan 1, 1982

By Kenneth L. Maloney

Ten small and intermediate-sized [11 GJ/hr to 264 GJ/hr (10,000 lb/hr steam to 250,000 lb/hr steam)] coal-fired boilers in the upper Midwest have each been tested on both a bituminous eastern coal and a subbituminous western coal. The purpose of this study was to determine the feasibility of substituting western subbituminous coal for eastern bituminous coal as a means of reducing the SO x emissions from this class of boiler and to demonstrate the feasibility of greatly expanded western coal utilization as a means of reducing the use of oil and gas. The scope of this study was such that the representative boiler types were tested on both eastern and western coal for a period of time sufficient to completely characterize their individual emission and operational characteristics.

Jan 1, 1977

By F. McCarthy, W. Zhang, R. McDonald

"The processing of nickel laterites has been a topic of major interest at CSIRO for almost twenty years. During this period CSIRO has collaborated with other researchers and industry in developing a better understanding of existing processes and been actively involved in testing/developing new beneficiation and process options for these ores. The current paper summarises the results of selected studies and highlights improvements that have been achieved. Key topics to be discussed include enhancements in the mineralogical characterisation, beneficiation approaches, improvements in the understanding and application of leaching technologies, the development of synergistic solvent extraction (SSX) for the recovery of nickel/cobalt from laterite leach liquors and the collaborative development of the Direct Nickel process. Future opportunities and key research questions will be briefly examined.INTRODUCTION Nickel laterite ores comprise a significant resource in Australia and according to United States Geological Survey data nearly a quarter of world reserves are located there (USGS, 2016). More specifically, around 95% of Australian nickel resources (laterite and sulfide) are located in Western Australia (Australian Government, 2017). Given the recent closure of Queensland Nickel, essentially all of Australian nickel production occurs in Western Australia and the primary producers of processed nickel products include Nickel West (Kwinana) with ~84,000 t saleable nickel metal in 2016 (BHP Billiton, 2017), Minara Resources (Murrin Murrin) with 46,700 t nickel metal produced in 2015 (Glencore Australia, 2017), and First Quantum Minerals Ltd (Ravensthorpe) who sold 25,882 t nickel as mixed hydroxide product in 2016 (First Quantum Minerals, 2017). The total sales of nickel from Western Australia in the 2015-16 financial year were 175,722 t. The study of nickel laterites at CSIRO recommenced at the time second generation High Pressure Acid Leaching (HPAL) plants were being commissioned at Bulong, Cawse and Murrin Murrin in the late 1990’s. A combination of technical and engineering issues meant that the ramp-up times at these operations were slower than expected and the outcomes resulting from the attendant problems are well documented (e.g. Griffin & Becker, 2000; Reid & Barnett, 2002; O’Callaghan, 2003) while the issues faced at the BHP-Billiton-built Ravensthorpe plant have been addressed by the current owners of this project, First Quantum Minerals Ltd (Piper, 2012)."

Jan 1, 2017

By J. W. Spyker, D. H. Filson, W. H. W. Husband

"Large deposits of sodium sulphate exist in southern Saskatchewan in the brines or muddy crystal beds of alkali Jakes. Currently, more than 300,000 tons per year of sodium sulphate are produced from these lakes and sold as salt cake to the paper industry. Most of the production is obtained from the brines of a limited number of Jakes.The Saskatchewan Research Council was requested to develop a process for recovering sodium sulphate from the muddy crystal beds so that this type of deposit could be exploited in the future. A flowsheet was developed with the aid of phase diagram data and the process was studied on a pilot-plant scale using raw material from three different lakes. Satisfactory yields and product purities were obtained in all cases, and an economic analysis indicated that a 100,000-ton-per-year sodium sulphate plant could produce salt cake at a cost of $12.26 per ton for a rate of return upon investment of 16 per cent at current market prices."

Jan 1, 1966

By A. W. Deurbrouck

The Bureau of Mines analyzed 13 samples collected from three Randolph County coalbeds. The Peerless and Sewell bed samples were generally of metallurgical quality as received from the mines or could be easily upgraded. How-ever, the Lower Kittanning coa1bed samples proved to be quite inimical to upgrading to metallurgical quality.

Jan 1, 1966

By Roland W. Rammler

In recent years, the crude oil reserves of the world have increased at the same rate as the consumption. A Consideration of the global figures suggests that adequate supplies of petroleum will be available during the next decades. On the other hand, it in a fast of economic and political significance that the reserves in the industrialized countries increase much more slowly than in the developing countries. In Western Europe the reserves have even decreased. At the present time, about 70 % of the petroleum reserves of the world are in the Middle East and in Africa in regions in which political arises are prevalent or impending. For the industrialized countries, the discrepancies between the consumption and reserves in various regions of the world are a strong urge to investigate whether oil can be recovered from other sources. The situation will probably not be changed to a large extent by the discovery of oil in the north of Alaska. The main starting materials for the production of synthetic crude oil are coal, oil shale and tar sand. In North America, where the consumption of petroleum increases more rapidly than the reserves, there are enormous deposits of each of the three materials. This fact is another incentive toward the utilization of these unconventional oil reserves, which provide a reliable basis for a supple of energy for a long time to come.

Jan 1, 1970

By Michael J. Beus

This Bureau of Mines report describes field investigations conducted in the Coeur d'Alene mining district of Idaho to obtain data on rock stress and physical properties. The resulting information has been utilized as input to detailed finite-element analyses to establish structural design criteria for deep-vein mine shafts. Measurement techniques include the Council for Scientific and Industrial Research biaxial and triaxial strain cells, the U.S. Geological Survey solid-inclusion probe, and the Colorado School of Mines dilatometer. Physical property testing was conducted in the laboratory on core obtained from each test site. Limited in situ physical property tests were also conducted. Reason-able success was obtained with the CSIR equipment, which was considered the most suitable for stress measurement in the study area. Test sites ranged in depth from 1,200 to 7,700 feet and are described in detail. The stress data were reduced by least-squares linear regression techniques to enable prediction of vertical and horizontal stresses to 7,500 feet. Ratios between the horizontal stresses as utilized for shaft design varied considerably, and a hydrostatic condition is the exception, based on Bureau measurements. Physical properties also varied widely, due to the complex geologic structure. Analyses of the data in terms of the tectonic history of the area show reasonable correlation. Data from previous rock mechanics investigations from the Coeur d'Alene district were also compiled and presented as part of this report to justify any generalizations regarding stress conditions and physical properties of the district as a whole.

Jan 1, 1980

By A. W. BELDEN

Among the investigations that the Bureau of Mines is conducting witha view to increasing efficiency in the utilization of fuels belonging to or for the use of the Government is an investigation of the processesthat take place in a foundry cupola during a melt. Some observations on the results of cupola tests of cokes at the Government fuel-testing plant in St. Louis, Mo., the coke being fromcoal from many coal fields of the United States, have been stated in a previous bulletin.s Especial attention was given to the meltinglosses that resulted from the use of different grades of coke, light and porous or heavy and dense. These losses amounted in one instance to 52.5 per cent of the iron charged and showed, in convincing manner, the need of exact information in regard to conditions in the fuelbed of the cupola.b Melting losses of iron have been fully appreciated but little under-- stood. The fact that these losses were possible with either light or heavy coke led to the belief that by using small charges 80 placed that. melting would take place in that zone of the cupola where the highest heat and the smallest percentage of oxygen prevailed and by confiningall melting to this zone these losses would be eliminated and the economical use of practically any coke produced for metallurgical purposes would become possible. This widening of the field from whichcoke might be drawn for foundry purposes would serve to place the foundryman in an independent position as regards his source of supply, and would tend to conserve the better grades of coking coals, which are being rapidly exhausted, by making the poorer grades available for mixing with them. In order to investigate conditions within a cupola, the Bureau of Mines as a first step decided to install a commercial cupola, to sample the gases during their travel from the tuy~res upward, and to determine the temperature of the fuel bed.

Jan 1, 1913

By Martin Langenderfer, Catherine Johnson, Phillip Mulligan, Kelly Williams

The physical geometry of a charge has a direct correlation to the geometry of the shock wave. This relationship appears strongest within the boundaries of the visible fireball. As the shock wave propagates outward past the limits of the fireball, the theory states that the geometry of the shock wave should even out and become more spherical. This paper investigates pressure vs. time at two distances, one ‘Near Field’ at the extent of the fireball and one ‘Far Field.' The two Fields were instrumented with three free-Field pressure probes from PCB oriented at 0, 45, and 90 degrees to the front face of the charge, in the same horizontal plane as the charge. This orientation allows for the comparison of the shock wave from the face and vertices of the charge. All the pressure sensors were connected to a Data Acquisition System (DAS) recording at 2 million samples per second (2MS/s). Two high-speed cameras, a Phantom and an MREL Ranger II, recorded the detonations for qualitative examination of the fireball, and the shock wave. Three charge geometries were used and compared to the shock propagation of a sphere. The other geometries tested are cylinders, cubes, and tetrahedrons. Charges were made from a PETN based sheet explosive. In the Near Field, a lower pressure is observed along charge vertices with highest pressures from each face. In the Far Field, vertices record a higher pressure, possibly due to the shock waves from the adjacent faces intersecting, indicating that shock pressures do not always even out in the Far Field. This paper will describe the methodology and findings of this experiment and attempt to determine causality for trends in the data gathered.

Jan 1, 2018

By W. G. Hubler

It has been within only the last two or three years that enough progress has been made in preferential flotation to warrant metallurgists in recommending the installation of commercial-sized plants for the treatment of copper-zinc-iron ores. Until the new processes had been worked out successfully, the treatment of this type of ore had proved a stumbling block in the path of metallurgical progress. Separation of lead-zinc ore is comparatively simple. A lead-zinc ore low in iron may be separated and concentrated by gravity con-centration, provided it is not necessary to grind too fine. Owing to the specific gravity of chalcopyrite and sphalerite being so nearly the same, however, their separation by gravity concentration is out of the question. Complex lead-zinc-iron ores in which the several minerals are intimately associated, requiring fine grinding to free them, have been successfully treated by flotation for the past fifteen years. Galena is easily floated, and its flotation, unlike that of chal¬copyrite, is not affected by the reagents used to inhibit the flotation of sphalerite and iron sulphides. When an attempt was made to use the methods of lead-zinc se-paration on copper-zinc ores, it was found that the depressant re-agents added to inhibit the flotation of the iron and zinc minerals would, under certain conditions, depress a large part of the copper. It was also recognized that, in the grinding of copper-zinc ore, soluble salts were generated which were detrimental to flotation unless properly controlled. The main part of this paper will be a discussion of solutions in the grinding circuit in relation to the pro¬duction of soluble salts and their effect on flotation.

Jan 1, 1931