Search Documents

By H. El-Faramawy, A. Ahmed, M. Eissa, M. El-Fawakhry, T. Mattar, S. N. Ghali, E. M. Kotb

As a result of the depletion of high-grade manganese reserves, it has become necessary to consider the exploitation of low-grade manganese ores. The main problem of low-grade manganese ore is the low Mn/Fe ratio, which makes it unfit for the production of manganese ferroalloys. In this work, a selective reduction technique was used for smelting low-manganese ore in the presence of coke and fluxing material in an electric submerged arc furnace to obtain a rich manganese slag and low-manganese pig iron. The product slag was blended with medium-manganese ore and smelted in an electric submerged arc furnace, in the presence of coke and the fluxing agent, to produce silicomanganese alloy. The influence of reducing agent ratio, charge basicity, and charge Mn/Si ratio on the smelting process was investigated. The optimum conditions were found to be a coke ratio of, 1.35, Mn/Si ratio of 2.0, and charge basicity of 2.5. The silicomanganese alloy produced under these conditions satisfies the specifications for Si16Mn63 and Si17Mn65. The experimental results were applied on a pilot scale, producing a silicomanganese alloy with a chemical composition close to that of the standard specifications.

Jan 2, 2022

By David E. Nicholson

In a Bureau of Mines investigation of the dynamic compaction of mine hydraulic backfills, two basic forms of mechanical vibration inducers were used and compared for effectiveness of compaction. Internal compaction, using concrete probe vibrators of various sizes, and external compaction, using plate vibrators} were studied and evaluated for use in underground stopes. An aluminum plate, which was light and displaced sufficient volume to remain afloat in fluid fill, and a steel plate were both used in the external compaction tests. Efficiency of compaction was better in studies conducted with internal probe vibrators. Tests were conducted in an underground backfilled stope with three different-sized probe vibrators (2-, 4-, and 6-inch-diameter) to determine an approximate area of influence. Results showed the areas of influence to be approximately 3, 4, and 5 feet in diameter, respectively, for the three different probes. Physical properties of hydraulic slurries were determined; preferred grain-size distributions, water exudation properties, and water contents of hydraulic slurries are reported. The best compaction results were obtained with moderately well-graded, fully saturated backfills, with slow rates of water exudation, which were capable of remaining in a semifluid state during the compaction process.

Jan 1, 1967

By W. Zheng

Pipelines can develop stress corrosion cracks in either intergranular or transgranular form. Since the mid-1980s, numerous colonies of transgranular cracks have been found across Canada and many other countries in the world. While the intergranular form of cracking has been well studied in the past 40 years, the mechanisms governing SCC in near-neutral pH environment, i.e., the transgranular form of the cracking, are yet to be understood in greater depth. Over the past ten years or so, a large number of research publications have been available on this subject and this paper summarize our latest progress in understanding the mechanistic aspect of the problem. Better understanding of the role of mill scale surface and the steel metallurgy in crack initiation has been indicated in the recent literature. However, the initiation of SCC in the lab research still relies on loading conditions that are far more aggressive than those encountered in the field. Most crack growth studies in the past are also performed under very aggressive mechanical conditions, which could have prevented the observation of environment effects. However, more recent research at lower K or Delta K ranges seems to suggest a strong role of the environment. Naturally, modeling of growth should reflect the effect of the environment, steel metallurgy, and the changing mechanical properties of the pipe steel with time. For a specific steel in a given environment, the crack growth rates tended to increase with the strain rate, indicated either by the nominal applied loading frequency or by the calculated crack tip opening rate. Future research needs to address the issue of concurrent growth of multiple interacting cracks. More attention should also be given to concurrent initiation of multiple cracks in a colony, as failure is usually caused by a coalesced crack not by an individual crack. The effect of soil environment should not be limited to the chemistry of soil solution; other factors such as cathodic processes, the variation of environment with time and physical conditions of coatings should also be considered as part of the study.

Jan 1, 2005

By Michael P. Hardy

The report described improvements and applications of the Hybrid Computer facility. Improvements implemented under U.S.B.M. Contract H0252035 included expansion of the capability to model nonlinear seam behavior, installation of a color video output display monitor, and further development of software capabilities. To demonstrate the capability of the system, firstly, the influence of nonlinear seam behavior response to the occurrence of coal mine bumps was fully investigated and secondly, the effect of improper mining sequence on bump occurrence was demonstrated. In addition, the system was applied to the analysis of a series of practical coal mine problems. Mines in three coal seams were analysed to investigate the parameters which contribute to the occurrence of coal mine bumps.

Jan 1, 1977

By E. Asselin

Electrochemical polarization experiments were conducted on alloy 625 in ammonia solution between 25 and 225°C and the results were compared with those of an oxygen solubility model. Results confirm that corrosion is under oxygen control, Normalized corrosion rates are determined based on the rate of oxygen diffusion to the corroding surface, and the corrosion rate at 200°C (-9.7 µA.cm-2) is roughly 24 times higher than the corrosion rate at 25°C (0.4 nA,cm-2), An oxygen-solubility model for Supercritical Water Oxidation (SCWO) conditions was generated using the Redlich¬Kwong-Soave (RKS) equation of state, Results of the model confirm many of the experimental observations from SCWO reactors which suggest that corrosion is at a maximum at temperatures just short of the critical point, The RKS/oxygen diffusion model predicts that the corrosion rate at 365° C is ?85 times higher than the corrosion rate at 25' C. Given that a normalized corrosion rate is obtained, this type of model could be useful for selection of SCWO reactor materials.

Jan 1, 2005

By D. J. Donaven, Manuel Gomez, W. S. Landers

Bulk density tests were made on a Western U.S. coke oven plant blend to obtain bulk density control data that would be directly transferable to plant practice . Maximum bulk density values were obtained at zero surface moisture . Increase in surface moisture to about 6 percent decreased the bulk density to a minimum value . Increase in the fine grinding of the blend , at constant surface moisture , decreased the bulk density . The effect of oil on bulk density was observed with five oils at concentrations ranging from 1/8 to 1-1 / 2 gallons per ton . Maximum bulk densities were obtained within the 1 / 2- to 1 - gallon - per - ton range . Essentially the same bulk densities were obtained with petrolatum- and nonpetrolatum- containing oils . Storage effects were observed on samples tested at selected intervals from 0 to 56 days . No significant change in bulk density took place if no surface moisture was lost during storage .

Jan 1, 1964

By Charles E. Green

This study was conducted to identify, evaluate, and develop procedures to minimize or eliminate safety hazards associated with the electrokinetic dewatering process, such as toxic and volatile gas emissions, electrical shock, accidental detonation of explosives, electrochemical corrosion of metal appurtenances, and possibly others. The identification, evaluation, and procedure development were based on pertinent literature, existing safety regulations, interviews with mine personnel, physical and mechanical properties of the electrokinetic dewatering process, and physical characteristics of the material to be dewatered. The electrokinetic dewatering process was described in detail. Potential safety hazards were identified and evaluated. Procedures and/or safety regulations were developed to minimize or eliminate the potential hazards. It was recommended that the electrokinetic dewatering process when used in deep metal mines be properly monitored to obtain additional information on other potential hazards that possibly exist.

Jan 1, 1979

By B. C. Alberts

Planning the use of South Africa's energy resources, especially coal, is of the utmost importance. The State and the mining industry require reliable official estimates of the economically mineable coal reserves for planning purposes. An overview of al the previous reserve estimates is given, with specific attention to the two most recent estimates-those of Petrick and De Jager. The differences between these two estimates are highlighted. The following important aspects are discussed: . the need to update the information regarding South Africa's mineable coal reserves, . the necessity of understanding and agreement between the coal-mining industry and the State department responsible for updating the coal-reserve data, and . the importance of the specific assumptions used in the updating of the data. A downward adjustment of mineable reserve figures is proposed, and the factors that influence the meaningful exploitation of the coal reserves are discussed. A recommendation is made as to how the Waterberg coal reserve should be exploited, and it is concluded that the Soutpansberg Coalfield cannot be exploited economically in the foreseeable future. An evaluation of the status of the coal-export trade is made and compared with the assumptions and targets set at the start of the coal-exportation scheme. The comparison shows the extent to which the exploitation of the coal reserves is being negatively influenced by the current market situation. Recommendations are made regarding planning for the coal-export market, and the aspects that have to be taken into account to keep South Africa in the export market are identified. Reference is made to the fact that the present unrestrained wage and salary adjustments, which show a total disregard of South Africa's poor productivity record, require serious thought and speedy rectification if the country is to survive in the export market. A salary and wage strategy must be developed to suit the specific needs of the Republic of South Africa.

Jan 1, 1987

By BUREAU OF MINES

This report is submitted in accordance with the provisions or une Synthetic Liquid Fuels Act of April 5, 1944 (30 U.S.C. 321-325, as amended), which require that: "The Secretary of the Interior shall render to Congress on or before the first day of January of each year a report on all operations under this Act." Owing to the broad scope of the content and the diversity of interests represented, the Annual Report for 1951 has been divided into two separate publications. Each has been published by the Bureau of Mines as a Report of Investigations, and the respective titles follow: Oil from Coal. R. I. 4865, Part I - R. I. 4866, Part II - Oil from Oil Shale. Identical in each report, the introduction summarizes research progress made in 1951 under the entire Synthetic Liquid Fuels program. A free copy of these publications may be obtained by a written request to the Bureau of Mines, Publications Distribution Section, 4800 Forbes Street, Pittsburgh 13, Pa. The R. I. number and title of the publication desired should be indicated.

Jul 1, 1952

By George A. Burrell, Frank M. Seibert

The Bureau of Mines, as part of its designated duty of investigating the causes of mine accidents, is conducting at its experiment station in Pittsburgh, Pa., a study of mine gases. Some of the work already done in connection with this study is outlined below. A large number of mine-gas samples have been collected under normal conditions in returns and in splits, and at other points in the ventilating current, also at the face, in the goave or gob, in unventilated places, and wherever the air was still. Samples have also been obtained under abnormal conditions, as after explosions and while mine fires were in progress, or from sealed areas behind stoppings and darns where the air had been stagnant for some time. Chemical changes in the composition of mine atmospheres during mine fires have been studied," and conditions peculiar to certain mines have been investigated. The question of the effect of a change in atmospheric pressure on the escape of gas (methane) in coal mines has been studied. Explosives have been fired in both coal and metal mines, and samples of resulting gases have been collected to ascertain the degree to which these gases vitiate the air. A series of samples in mines where gasoline locomotives were being used have been examined in order to ascertain the degree to which the exhaust gases from such locomotives foul the mine air. Experiments have also been performed in regard to the relative effect of carbon monoxide b upon men and small animals. A preliminary report relating to the inflammable gases in mine air has been published. Full reports of the results of the investigations outlined above will be published as soon as all the necessary data have been gathered. The first part of this report deals with the methods used by the bureau in the collection and examination of the various mine gases; the latter part discusses the bureau's methods of sampling and examining natural gas.

Jan 1, 1913

By George H. Bodfish

This paper begins with a short history of air compressors, emphasizing their "roots" in the mining industry. It then describes the types of compressors available, including reciprocal, the various rotary positive-displacement compressors, and the centrifugal. The advantages and disadvantages of selecting a certain type of compressor over another are enumerated, considering customer requirements and operating costs, among other factors. Guidelines to operation and maintenance are discussed, including installation, monitoring and maintenance procedures. Finally, the paper addresses itself to future trends, with special attention being given to the system concept, the increasing use of rotary compressors, power consumption, reliability, packaging and noise attenuation.

Jan 1, 1978

By Youngkook Lee

The precipitation kinetics of NbC in ferrite matrix of the Nb microalloyed steel was investigated experimentally and numerically. The mole fractions of NbC precipitates formed at different isothermal temperatures were measured as a function of holding time by electrical resistivity test and were compared with both a mathematical model based on time-dependent nucleation and growth rates and the hardness. There is a good match among the calculated and measured precipitation kinetics of NbC and the hardness. The isothermal precipitation-temperature-time diagram of NbC in ferrite matrix of the Nb microalloyed steel was newly generated. Keywords: Precipitation, Carbide, Ferrite, Nucleation, Growth, etc

Jan 1, 2003

By M. Kosugi, M. Kawata, J. V. Satur, K. Mitsuhashi, R. Kawarabuki, W. Kracht, Y. Ebisu

Copper concentration is becoming more difficult because remaining copper ores are more complex and of finer copper mineral grain size, making copper minerals harder to float because of the fine particle size required to liberate the valuable species. The purpose of this work was to study the flotation behavior of fine copper sulfide ores at different conditions of agitation and aeration. The experimental campaign was carried out in a laboratory Denvertype flotation cell of 1 L volume modified to be operated with forced air that allows decoupling air flow rate and agitation speed. Four ore samples from Chile were used, all of them containing copper sulfides such as chalcopyrite, bornite, chalcocite, and tennantite, but with varying grain sizes and compositions. Preliminary flotation tests for establishing the flotation conditions of grinding size and collector dosage were conducted before the kinetic flotation tests that were carried out at different agitation speeds varying from 900 to 1300 rpm for gas flow rate ranging from 1.6 to 7.2 L/min. The flotation products were analyzed by ICP-MS and MLA (Mineral Liberation Analyzer). The results showed that high agitation speeds with corresponding air flow rates resulted in better recovery than moderate agitation speed and air flow rate, and an excess in gas flow rate resulted in bad performances. The flotation rates of the fine copper minerals were improved despite the different improvement rates among the fine size fractions. The impact of these operational variables, however, was different when comparing the results for the four ore samples. While it was found that the order of floatability in the four samples was the same, that is, chalcocite > tennantite > bornite > chalcopyrite, the kinetic constants of the copper minerals in the samples were different, indicating that mineral composition in the sample affects the flotation kinetics.

Jan 1, 2018

The primary (sulphide) resources at Aphrodite are refractory in nature, requiring an oxidation process stage to be introduced to facilitate extraction of the gold. The company is investigating the use of pressure oxidation (POX) as the oxidation method for processing of high grade gold bearing concentrate it plans to produce at Aphrodite. POX has been used extensively around the world for the past 30 years and continues to be the favoured option for a number of refractory gold plants currently in the design and construction stages. Initial pressure oxidisation testing investigated the effect of temperature, pressure and grind size on a bulk flotation concentrate prepared from Alpha lode material. The concentrate averaged 47.3 g/t gold and was prepared from a composite of core samples averaging 1.49 g/t gold. Sub-samples of the concentrate were subjected to POX for 1 hour resulting in rapid oxidation during this very short period. Testing undertaken showed that there was a significant increase in sulphide oxidisation at higher temperature (220°C) and pressure (2,500 k/Pa) for the two grind sizes (75 and 20 microns) evaluated. The proposed flowsheet, OPEX and CAPEX are critical aspects for project development.

Jan 1, 2014

By Philip Thompson

"Carefully planned laboratory test programs provide valuable data regarding the amenability of low grade gold ores to heap leaching. The most common laboratory test is the column leach test. The overwhelming problem associated with this type of test is the limit on the test column height. Most laboratories use a three (3) meter (10 foot) high column as a standard test due to building ceiling limitations, sample size limitations, etc. This paper presents a case study in which an ore sample was tested in a 1.5 meter, a three meter, and a six meter high column to determine the effect of column height on the test results. Other important factors such as sample preparation protocol, preliminary bottle roll testing to determine appropriate crush size, column diameter requirements, and leach solution analyses, are also discussed.IntroductionColumn leach testing has been used for years by many laboratories to determine the amenability of low grade precious metals bearing ores to heap leaching. However, the test work can be compromised by poor planning, misinterpretation of results, and extrapolation of data beyond the reasonable boundaries of the experiment. Preliminary test work should be performed prior to column testing. This preliminary work provides valuable information regarding the response of the ore to cyanidation and aids in the design of the column tests.The sample should be screened into various size fractions prior to testing. The fractions are assayed to determine the gold content of each size fraction and of the overall sample. The most valuable preliminary test is the bottle roll cyanidation test which is usually performed on five kilograms of coarse sample in a large rolling bottle which can accept material up to 50 millimeters top size. The residue from this test is screened at different sizes to determine the distribution of unleached gold in the residue. Comparison of the gold distribution in the leach residue with the distribution of gold in the feed at the same size intervals provides an indication of the appropriate crush size for the sample. The overall gold extraction from the sample at the crush size tested is also determined from these data. Lime and cyanide requirements can also be estimated from this test. The viscosity of the bottle roll pulp and the size distribution of the feed and leach residue can also suggest whether agglomeration of the ore will be required prior to column testing. Ores which contain significant amounts of clays (greater than 5 percent) will generally require agglomeration to prevent plugging of the test column."

Jan 1, 1997

By Thierry Bernard

To be able to precisely predict the result of a mine blast before pressing the button is a goal for many blasters due to the environmental and economic constraints of our century. Based on the fundamental fracturing of the mechanism of rocks by explosives, the most recent research in digital modeling, the power of present computers, and the possibilities offered by drones, we have designed a realistic digital 3D simulation model for mine blasts

Feb 1, 2020

By Junli Xu, Xianwei Hu, Kaiyu Xie, Liangxing Li, Zhongning Shi, Zhaowen Wang, Bingliang Gao, Aimin Liu

Al-Ti master alloys were prepared by aluminothermic reduction between the dissolved titanium dioxide and aluminum in cryolite melts at 960oC. The kinetic analysis by differential scanning calorimetry indicated that the apparent activation energy of the reaction of reducing titanium dioxide by aluminium is 22.3 kJ/mol, and the reaction order is 0.5. The products were analyzed by means of X-ray diffraction, X-ray fluorescence, scanning electron microscopy and energy dispersive spectrometer. Results from X-ray diffraction showed that the phase compositions of produced alloys are Al and Al3Ti. In addition, Al-Ti master alloys containing 2-6 mass% Ti were formed at different reduction time of 2-5h in aluminothermic reduction experiment.

Jan 1, 2015

By A. K. Das, S. Pathak, C. Bhanu, P. K. Tripathy

Ferroalloys are integral part of steel melting process. The purpose of using ferroalloys is three fold e.g. killing of steel, modifying the slag composition and steel alloying. Amount of ferroalloys used for alloying is subject to requirements of steel properties e.g. yield strength, ductility, formability etc. Variety of ferroalloys (some-times pure metal) is used by steel industries depending upon their techno-economic feasibility. Size, chemistry and modes of addition of ferroalloys are suitably engineered to bring in operational consistency and cost benefits. Of late, Tata Steel has tried out a few ferroalloys for the first time with interesting results to meet the specific requirements of high strength interstitial free (IF) and micro-alloyed steels. Some of these ferroalloys have been put into regular use with complete or partial replacement of ferroalloys used earlier. Size of one of the ferroalloys has also been modified without any other adverse effects. This paper summarizes requirements of ferroalloys for the steel industry with special emphasis on recent trials.

Jan 1, 2007

The Bureau of Mines has long been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts, the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions1 issued by the Bureau of Mines, and the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. The Government, with the exception of the Tennessee Valley Authority, purchased approximately 5.5 million tons of coal in fiscal year 1971. In connection with these purchases, the Bureau analyzed 4,366 samples. These are published (table 1) for the use of Government officials and the public. Such analyses of delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1972

By C. Isaac Garcia, Sihai Jiao, Anthony J. DeArdo

"A practical model based on the Hill analysis has been developed to calculate the Lankford value of interstitial free (IF) steels and its distribution in different rolling directions, by considering only a few selected texture components. The Texture Intensity Ratio (TIR), i.e. (111 ) /(100), was used in the model to describe texture. By using the new TIR parameter, the texture-based prediction models can be used more easily to predict the Lankford value in a rather straightforward way.IntroductionThe deep drawing capacity of sheet steels is generally indicated by the Lankford value, which is mainly determined by the texture in steels1. Traditionally, various models derived from the Taylor model are employed to calculate the Lankford value from the texture2-4. In such models, the plastic deformation of steel is assumed to be the result of the slip of dislocations in certain slip systems, i.e., by either pencil glide or restraint glide. The slip direction is the <111> direction. In the case of pencil glide, the slip is thought to be possible in all crystal planes with the <111> crystal direction. Assuming the material is elongated in the X1-direction by d n and compressed in the X2 and x3-direction by qd n and (l-q)d n, respectively, corresponding to a deformation tensor"

Jan 1, 2001