Search Documents

By Albert W. Deurbrouck

This report describes the preparation characteristics of the Pittsburgh and Upper Freeport coalbeds in Hancock , Brooke , Ohio , and Marshall Counties , W. Va . Over 4.5 million tons of coal was produced in these four counties in 1962. Most of this production came from the Pittsburgh coalbed . Twelve coal samples were collected for this study , 11 from the Pittsburgh bed and 1 from the Lower Freeport bed . Two of these samples could be upgraded to produce metallurgical - grade coal . The sulfur content of the Pittsburgh- bed coals was generally excessive --as high as 4.9 percent in the raw coal and 3.19 percent in the float 1.30 specific gravity fraction . The rank of the coals in this area ranges from high-volatile A to high-volatile B bituminous .

Jan 1, 1964

By Norman A. M Macleod

FOR the past seven years, all flotation at the Britannia mill has been done in Forrester Air-Lift cells. Prior to 1931, the roughing and part of the cleaning operation had been performed in four 21-cell and two 14-cell M.S. machines. The resulting economies in reagent, power, maintenance, and general operating costs, and the increased recovery, more than justified the exclusive use of the Forrester machine. About three years ago, the possibility of still further improving the efficiency of the flotation section was the subject of considerable discussion and experiment. Arising from these experiments, tests were made of the practicability of using a cell of greater depth than that of any pneumatic or mechanically-agitated machine in common use. Cells were constructed with depths of 7 .5 feet, 10 feet, and 15 feet, and, in all cases, a very definite improvement in operation was indicated. The cell now being used in the mill treats from 5,500 to 6,200 tons of dry feed per day. It is 100 ft. long by 5 ft. wide by 8 ft. deep, and has replaced a total length of over 500 feet of standard Forrester machine. The choice of a depth of 8 feet was governed by the type of blower which was available-in this case, a Roots-Connersville blower, driven by a synchronous motor and delivering 6,000 c.f.m. of free air at 4.0 pounds per square inch. At the Chelan Division of the Howe Sound Company, where a new mill was recently built, all flotation is carried on in cells 10 feet deep, with good results.

Jan 1, 1938

By J. B. Rosenbaum

This report presents new findings and consolidates previously published data to provide a single reference containing a concise and comprehensive description of the Bureau's work on electrolytic chromium. Two separate systems for electrolytic-chromium recovery were developed, one designated as the oxidized system the other as the reduced system. The electrowinning of chromium metal follows the dissolution of chromium from the ore or from ferrochrome and its separation from gangue and metallic impurities. Chromite was first solubilized by pressure digestion at slightly elevated temperatures in an oxidized acid solution using Na2Cr2O7 as an oxidizing agent. Later it was found that a sodium-free electrolyte was preferable, using return-cell anolyte containing H2SO4 and Cr03 as the oxidizing agent. Gangue materials were separated from the soluble metallics by filtration; and, after the Cr+3 had been stabilized, the metallic impurities were separated as crystalline ammonium salts by vacuum crystallization.

Jan 1, 1957

By Alvin Schallis

The. problem of supplying enough magnesia for the American war effort has become highly important. Before hostilities began, only about two-thirds of our, require vents came from domestic sources; now they must supply almost all the magnesia we need. A further burden is placed upon our own supply by the fact that more and more magnesia is being required, not alone to pace the war tempo of general industrial activity, but also to replace chrome ore in refractories and to make magnesium metal. The domestic magnesite and brucite industry is equipping itself to satisfy much of this greater demand for magnesia, but the remainder must be obtained elsewhere. The principal sources of magnesia are magnesite, brucite, dolomite or high-magnesium limestone, natural brines, sea water, salt-works bitterns, magnesium silicates, and magnesium salts. Although dolomite is tae subject of this paper, it should be considered in perspective with all these highly competitive sources of magnesia.

Jan 1, 1943

By C. H. Schack

Extractive metallurgy techniques currently employed to recover silver from primary ores and secondary scrap were reviewed and evaluated to identify and delineate metallurgical problems whose resolution would increase the supply of silver from domestic materials. The survey revealed that practically all primary silver is recovered by froth flotation concentration of various types of ores, followed by smelting and refining of the separate lead, copper, and zinc concentrates. Silver losses during the complex processing are, with rare exception, inconsequential. Furthermore, any silver production gain from base metal ores, which contribute about two-thirds of the total primary silver, is directly dependent no improvement in the market for the base metals. Statistical data on new and old silver scrap are wholly inadequate to make reliable conclusions about scrap processing problems and the possibility of increasing the recovery of silver from the many forms of secondary silver-bearing materials. The available information indicates (1) that efficient silver reclamation practices are employed by the larger users of silver, and (2) that recovery of additional secondary silver involves solution of problems of collection rather than of processing. Several possibilities exist for limited increases in silver production from primary ores by improvement in metallurgical practices. Specifically, research is needed to (1) solve the problem of recovering silver from the copper ores of the Copper Range district, Michigan; and (2) devise economically feasible methods for recovery of silver from presently marginal or submarginal ores char because of grade, location, and frequently complex nature cannot presently be exploited by conventional techniques.

Jan 1, 1965

By John J. Mulligan

Coalbeds were discovered in outcroppings of the Beacon group of sediments on the north end of the Willett Range ( altitude 77 ° 11 ' S , longitude 160 ° 20 ' E ) , Victoria Land , Antarctica , in December 1960 during an investigation undertaken as part of the U.S. Antarctic Research Program under the auspices of the National Science Foundation . Three separate exposures of coal or coaly material were found . Two of the exposures contain , respectively , eight and four beds of hard , compact , finely banded attrital coal ranging in thickness from 8 feet downward to a few inches , and reported to range in rank from mediumvolatile bituminous to semianthracite . The coals are associated with carbonaceous shales containing an abundant assemblage of fossil plants resembling those associated with the Permian coals of Australia and other Gondwana areas . The third exposure , apparently somewhat higher in the stratigraphic sequence , contains only coaly plant fragments scattered through a thin conglomerate and overlying sandstones . A sandstone bed that overlies these coal - bearing sandstones contains abundant logs and fragments of silicified wood . Preservation of features is poor , but one segment of a silicified stem suggests comparison with Rhexoxylon , a gymnospermous tree that usually is considered indicative of Triassic age . The Beacon sediments in this area have been invaded , broken , and uplifted by a massive series of diabase sills and dikes greater in volume than the intruded sediments . The heat emitted by these intrusives must have advanced the metamorphic development of the coals . However , there is no evidence of alteration to graphite , and coal found in direct contact with a diabase sill contains no vesicles or other usual evidences of natural coking . Either the pressure of overlying rocks inhibited the development of coke , or the coals had been metamorphosed beyond the coke forming stage before the igneous intrusion .

Jan 1, 1963

By W. A. SLOAN, G. L. Oldright, J. D. Sullivan, E. K. PRYOR, A. F. HALLET, R. S. Dean, S. L. BROWN, F. S. Wartman, A. J. Thompson

Lack of sufficient publication funds has resulted in the accumulation of considerable unpublished experimental work on copper metallurgy by the Bureau staff . The present report gives extended abstracts of this work , as well as a discussion of the best direction for future efforts . The experimental work reported in this series of papers was done in cooperation with the University of Arizona , Tucson , Ariz . The investigations covered in the third , fifth , and seventh papers were done under the direction of G. L. Oldright and the remainder under the direction of V. H. Gottschalk .

May 1, 1934

In 1960, the Secretary of the Interior, acting under the provisions of Public Law 454, 80th Congress, appointed a Lignite Advisory Committee to aid in programming research on coal (lignite) of the north-central area. The chairman of this committee is the Secretary of the Interior or his delegated representative, and in all meetings held during 1960 and 1961, the Director of the Bureau of Mines, Marling J. Ankeny, has presided. The members of this committee were R. W. Rovelstad, President, Baukol-Noonan, Inc., Noonan, N. Dak. W. E. Keller, Vice President, Northwest Division, Truax-Traer Coal Co., Minneapolis, Minn. A. M. Cooley, Professor of Chemical Engineering, University of North Dakota, Grand Forks; N. Dak.

Jan 1, 1963

By I. Govender, M. C. Richter, N. Mangadoddy

"We present an analysis of trajectory and time averaged data of near gravitational material (NGM) representative coal tracer particles within a magnetite medium passing through a 100mm diameter hydrocyclone imaged with PEPT (positron emission particle tracking) at iThemba labs, Cape Town. The tracking of neutrally buoyant tracers as well as the other NGM allows an empirical study of the approximate dynamical behaviours of both the dense medium as well as the range (size and density) of particles around the separator’s cut size within a partially imaged volume of the cyclone body lying within the field of view of the detector. The study was commissioned as part of a CFD validation study using empirical data from a real-world lab-appropriate system in order to shed light on the inner workings of hydrocyclones and their separation mechanisms. We employ various optimisation and noise reduction techniques within the analysis and follow a detailed investigation of the velocity fields derived from the raw spatial positions with an emphasis on the velocity profile within the forced and free vortex zones. Challenges encountered with this high velocity particle tracking experiment within a highly attenuating environment are also discussed. Various important velocity distributions are shown and compared to theoretical predictions. The power law decay profile of the free vortex and radial velocity scaling with regards to the Froude number are reproduced in line with the static particle approach. INTRODUCTION Cyclones have long been a vital industrial tool for the separation of different classes of particles. These cyclonic separators (with either gas or liquid medium) operate by forcing the solids-bearing fluid at high pressure into a cylindrical vessel causing high tangential velocity fluid rotation as well as, in the case of an “open” (with exit channels open to the atmosphere) cyclone, a central vortex air column spanning from underflow to overflow exit. The fluid is forced to exit the cyclone at two locations, the spigot and the vortex finder, generating the underflow and overflow respectively. The body of the cyclone usually terminates in a conical shape to focus the underflow stream. This geometry and large incident fluid velocity force high density materials toward the wall of the vessel where they are most likely to move along and down the inside wall away from the inlet to exit via the underflow while lower density materials traverse the cyclone body closer to the central vortex and are buffeted by the upward-moving column towards the overflow exit. This separation mechanism is selective of density and size in an interplay between the centrifugal force due to the rotation of the fluid and a drag force acting on the particles."

Jan 1, 2018

By F. F. Aplan, G. Simkovich

"A review is given of the effects of solid state point imperfections upon a number of mineral benefication processes and a metal extraction process. It has been found in numerous flotation studies that small amounts of aliovalent impurities (dopants) in binary compounds may show major effects upon flotation behavior. Both semiconducting and ionic conducting compounds are affected. These effects are also seen in hydrometallurgical studies as well as in electrostatic operations. Additionally, de-copperization of lead melts appears to be strongly influenced by similar defects. It is hypothesized that the effects observed in these studies are present in actual operations and should be considered in designing processes. A few speculations concerning future efforts are advanced. IntroductionImperfections [point (e.g., vacancies, interstials, quasi-free electrons, electron holes, impurity ions), line (e.g., dislocations), two dimensional (e.g., grain boundaries) and three dimensional (e.g., 2nd phases) defects] are generally present in solid materials and these imperfections may, and often do, have important effects upon a variety of properties and processes. In general, one may, in most cases, attain elimination of three dimensional defects by a separation process of one type or another (e.g., gravity, electrostatic, magnetic, flotation, hydrometallurgical etc.,). Thus, this type of defect has rarely been investigated in a systematic fashion. Two dimensional defects are always present in non-single crystal materials but have also escaped systematic studies in processes primarily because the control of such defects is not easily attained. Line defects are non-equilibrium entities which are present in ill-defined quantities so that they present a variable that cannot be easily controlled although through careful systematic experiments one can attain some reproducible relations pertaining to this type of defect.Contrary to the lack of studies concerned with the effects of 1, 2 and 3 dimensional types of defects there has been some activity concerned with point defects and their effects upon a number of mineral/metallurgical processes, especially flotation processes. Thus, this article will present a review primarily of point defects in relation to their effects upon flotation although other processes and defects will also be mentioned."

Jan 1, 1988

By G. Rehder

The release of methane as free gas from the seafloor into the water-column well within the hydrate stability field is a natural process observed today in various ocean settings, such as the Cascadia margin, the Black Sea, the Guayamas Basin, and the Gulf of Mexico. The subsequent dissolution of gas bubbles into the water-column determines the vertical distribution of aqueous methane in the water-column and the upwards methane flux. Understanding this process not only is essential to describing the impact of natural deep-sea gas seepage, but also to assessing the hazard potential from blowouts and offshore exploitation activities, which are steadily expanding to greater ocean depths. Furthermore, the fate of methane from seeps contributes to scenarios of global change in the past and future involving the large scale destabilization of gas hydrates on a. We recently reported on the extended lifetime of methane bubbles within the hydrate stability field due to the formation of a hydrate skin (Rehder et al., 2002), based on in situ measurements of methane and argon bubble dissolution in the depth range 400 to 800 m. More recently, these observations were extended to depths from 900 to 1500 m. Single bubbles were injected from the ROV Ventana into an attached, back-illuminated, flow-through imaging box. The ascent of individual bubbles within the imaging box was recorded with Ventana?s HDTV camera system by piloting the 3-ton ROV upward, at the bubble rise velocity, for up to 400 m of vertical transit. Observed rise velocities were approximately 30cm/sec for all depths. Post-dive analysis of the HDTV video allowed detailed measurements of the bubble shrinking rates. The results of the earlier and new experiments lead to the following conclusions: (A) Methane bubbles released below the hydrate stability field showed markedly enhanced lifetimes, attributed to hydrate skin formation. The change in radius with time, dr/dt, varied from -7.5 micrometer/s above the hydrate stability field to about -1 micrometer/s at the deepest release depth. (B) Bubble lifetime within the hydrate stability field increased with distance in P-T space from the hydrate phase boundary. (C) Before hydrate skin nucleation, dr/dt for CH4 bubbles was comparable to dr/dt above the hydrate stability field. Although variable, the onset time for the hydrate skin effect to occur generally decreased with distance from the hydrate phase boundary (super-pressurization and super-cooling with respect to hydrate formation). (D) Even before the onset of the hydrate skin effect, a slight decrease of dr/dt with increasing depth was observed.

Jan 1, 2005

By David White

This paper is the result of a comparative study of ultimate coal analyses made and published by the United States Geological Survey. This study, at first casually undertaken to devise an acceptable classification of coals based on chemical analyses, was continued in connection with a microscopic examination of a number of the coals. The initial comparisons, made from a relatively small number of analyses, not only confirmed a previous conviction that the elimination of oxygen incident to the development of a coal is economically far more important than has been generally suspected, but also showed that oxygen is very nearly as harmful as ash in coal. The immediate purposes of the present study were: (a) To determine more definitely, from a comparative examination of a large number of ultimate analyses, the relative importance of oxygen as an impurity in various coals; (b) to illustrate the transition between various grades of coal of similar origin-transition mainly due to progressive devolatilization, brought about more or less directly by dynamic influences; (c) to ascertain the relative proportions of oxygen, hydrogen, and carbon in coking coals, especially with reference to a theory tentatively framed to explain the coking quality; and (d) to forecast the probabilities of successfully treating a large number of coals so as to render them amenable, in a softened condition, to satisfactory study under the microscope.

Jan 1, 1911

By A. J. Kraemer

The properties of crude petroleum continue to interest the Bureau of Mines and constitute an important phase of its major studies on the mineral resources of the United States. The Bureau's interest in the subject has been intensified by frequent requests for information on the characteristics of crude petroleum from various producing fields. Since its inception the Bureau of Mines has collected and analyzed samples of typical oils and at present has surveyed and classified crude petroleums from nearly all the known oil fields of the Western Hemisphere. Results of these surveys have been presented in various Bureau of Mines publications. (See bibliography, appendix A, p. 145.) The nature and comparative value of crude oils from various countries and the extent to which these oils may be considered potential competitors for markets are of manifest importance to the petroleum industry in all lands, largely because all crude oils, wherever produced, are either actual or potential competitors for a market with all other crude oils. The numerous discussions of foreign production of oil that have appeared in the technical press in the past indicate the great interest of the United States in this subject.

Jan 1, 1937

By David R. Shields, Michael T. Bracher

"The $330 million (U.S.) Dana-Farber Cancer Institute’s Yawkey Center for Cancer Care (Yawkey Center) sits in the heart of Boston’s Longwood Medical Area. The Yawkey Center is a cutting-edge cancer care facility that houses Dana-Farber’s adult clinical care and clinical research programs. Standing 14 stories above grade, it includes 7 stories of underground parking extending 75 ft (23 m) below ground. The structure is on a 198 by 186 ft (60 by 57 m) site sandwiched between Dana-Farber’s 13-story Richard A. and Susan F. Smith Research Laboratories Building, the Medical Area Total Energy Plant (MATEP), Jimmy Fund Way, and Brookline Avenue, a busy four lane artery through the heart of the Longwood Medical Area. Together with Simon Design Engineering, the project structural engineer, GEI Consultants designed an innovative foundation and excavation support system to isolate the building from ground vibrations generated by the adjacent MATEP power plant. In effect, the Yawkey Center is a 21-story free-standing structure that starts 7 stories below grade.The MATEP facility provides power for 9 million sq ft (840,000 sq m) of occupied space in the medical area. There are six 32-cylinder diesel engine generators in the facility that produce low-frequency ground vibrations in the 10 Hz range, similar to the natural frequency of typical building elements. The resonant response of the Yawkey Center building structure to these ground vibrations would affect the performance of sensitive medical research equipment and cause an unacceptable environment for clinical care.The soil profile at the site consists of stiff clay, fine sand, glacial till, and bedrock consisting of hard metamorphosed conglomerate. In-situ measurements of ground vibrations performed in boreholes showed that there was little attenuation of the vibrations with depth in the soil layers overlying the bedrock, but the vibration amplitude in the bedrock was markedly lower than in the overlying soil. Based on this data, an innovative foundation system was designed to support the building on bedrock located up to 110 ft (34 m) below ground surface, while isolating it from the surrounding soil. This was done by physically separating the below-grade parking garage floors from the perimeter foundation walls to create a free-standing structure supported on the bedrock"

Jan 1, 2012

By N. S. Dalal, X. Shi, V. Vallyathan

"Electron spin resonance (ESRJ spectrum of the hydroxyl (· OH) radical spin adduct with .the spin trap 5,5-dimethyl-1-pyrrolintt-N-oxide has been obtained in suspensions of freshly ground quartz particles. The concentration of the spin adduct (and hence of the • OH radicals) increases with the amount of grinding. The dust's potential for the generation of the· OH radicals is maximum when fresh (i.e., immediately after grinding) and decreases to 50% in about a day on storage in air. Studies involving metal chelates .indicate that the • OH radical formation involves mainly the silica surface and H20 rather than the Fenton reaction. The results suggest that hydroxyl radical reaction(s) could be important in the lipid peroxidation and fibrogenicity by quartz dust, particularly .in acute silicosis. INTRODUCTIONIn this paper we report on our electron spin resonance (ESR) detection of the formation of hydroxyl (·OH) radicals in aqueous suspensions of freshly crushed quartz particles. This work was undertaken with a view to find possible clues to the role of free radicals in the pathogenesis of quartz-induced fibrogenicity, commonly known as silicosis. We noted that while silicosis is one of the major health hazards in coal and mineral industries, the mechanism by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrogenesis are still poorly ·understood (Reiser and Last, 1979; Singh and .Rahman, 1987). It is generally thought, nevertheless, that the action of quartz particles on the biological membranes is the starting point of the silicotic process (Parazzi et - al., 1968). A possible clue to the mechanism of the membrane damage by quartz particles, in terms of the role of oxygenated free radicals, is suggested by the following observations. A suspension of quartz particles in contact with alveolar macrophages has been reported (Gabor et al., 1975; Koike et al., 1982) to initiate an enhancement of lipid peroxidation, defined broadly as the oxidative deterioration of polyunsaturated components of lipids. Hydroxyl (· OH) radicals are known to be capable of peroxidation by abstracting hydrogen atoms from cell-membrane lipids (Halliwell and Gutteridge, 1985) and of initiating lipid peroxidation in lysosomal membranes. (Fong et al., 1973). Arong other lines, it is known that exposure of cell membranes, fatty acids, and unsaturated food oils to ionizing radiation, which generates· OH radicals, causes rapid peroxidation (Halliwell and Gutteridge, 1985). Thus • OH radicals (and also other oxygenated species such as Oi, 10 2, and H20 2) might be expected to play a role in the toxicity of quartz. Earlier studies of the aqueous chemistry of quartz suspensions have reported detection of H2O 2 (Kalbanev et al., 1980), implicating the formation of ·OH radicals as transient species. However, we are not aware of any report of the detection of • OH radicals in quartz reactions, and thus the present study was undertaken. Since it-is known that, because of their high reactivity (hence short lifetime) in aqueous media, the • OH radicals cannot be detected via ESR directly (Finkelstein et al., 1980; Buettner, 1982) we have used .ESR combined with the spin-trap methodology (Finkelstein et al., 1980) for studying the· OH formation. The results show that· OH radicals are indeed formed in aqueous suspensions of freshly ground quartz; thus pointing to ·a possible new clue to the cytotoxicity of freshly formed quartz particles and thereby to silica fibrogenicity."

Jan 1, 1988

By M. Cowling, S. Kumarl, A. W. Piper, R. A. Forsdick, C. Bailei, M. Patell

"The lead-refining process takes place in hemispherical vessels called kettles. In these kettles, lead-bullion is mixed at a certain temperature to remove impurities from the melt. This paper presents steps in a novel method for calculating vortex shape and flow field in the refining kettle using Computational Fluid Dynamics (CFD). First of all a two-dimensional axisymmetric model is used to calculate the vortex shape at the liquid-air interface. Here action of impellers and baffles are accounted for by adding source and sink terms to the appropriate momentum equations. The model includes Yolume of Fluid (YOF) method to predict the shape of interface deformation, i.e. vortex. This strategy reduces the computationally intensive three-dimensional transient simulations to a more efficient two-dimensional model. The calculated vortex shape is then used to regenerate a full three-dimensional grid. This grid is used to carry out steady-state simulation using the standard multiple-reference-frame method of impeller-fluid-baffle interaction within the commercial code Fluent. Simulation results for both stages of the development are compared with experimental data.IntroductionOne of the most important steps in Lead Refining process is impeller stirred mixing of Lead Bullion in hemispherical vessels. During this process, the melt is treated with one or more reagents in order to remove impurity elements such as copper, antimony, silver and bismuth. These impurities react selectively with the reagents and float to the melt surface in the form of a powdery layer, which is then skimmed for further processing. Figure-! shows (a) the lead refining kettle and (b) the schematic representation of involved flow pattern. Stirring of the lead bath using specific impeller designs, which creates a central vortex, provides a mechanism for draw-down and dispersion of the buoyant reactants. Clearly, effective control of the impeller generated vortex and flow pattern is crucial to achieving efficient operating conditions."

Jan 1, 2001

By R. D. Leitch

"INTRODUCTION The general program of the investigation of coal mine drainage which the Bureau of Mines is making includes, among its many phases and objectives, a study of the fate of the acid, content of drainage after it enters natural streams, and the effect of seasonal variations on the degree of contamination of streams. Opportunity for studying these under comparatively normal conditions and variations can readily be found, but there is only a chance opportunity for studying than under extreme conditions. The unusual drought that prevailed during the summer of 1930, however, created a condition of low water favorable to a study of one of the extremes.This report gives the results of an investigation of Bennett Branch of Sinnemahoning Creek, Pa., made under this condition.ACKNOWLEDGMENTSThis work was conducted under the direction, and with the advice, of Dr. R. R. Sayers, chief, Health and. Safety Branch, and of W. p. Yant, supervising engineer, Pittsburgh Experiment Station.DESCRIPTION OF BENNETT BRANCHBennett Branch, as shown in Figure 1, is a tributary to Sinnemahoning Creek. Its source is in Huston Township, northwestern Clearfield. County, from which it flows in a general northeasterly direction through Elk County, thenceeasterly in Cameron County to Sinnoning Creek at Driftwood. The total length is about 37 miles. There are nine towns along the stream that have an average population of about 350. There is no industrial pollution other that from coal mines and very little. domestic, pollution."

Jul 1, 1931

By K Williams, T Donohue, W Chen, T Roessler, A Katterfeld

Wet sticky iron ore poses particular difficulties in every aspect of the material handling process. Material hang-ups in bins, pipes and chutes; carry-back and spillage due to insufficient belt cleaning; clogging of screens; malfunctioning of crushers as well as rat holing of gravity reclaimed stockpiles are all predominantly due to the inherent cohesion and adhesion characteristics of the wet, sticky ore (Roberts, 1993). Limited understanding and quantitative measures on the stickiness of such a material significantly lower the mining operation efficiency.This research aims to investigate the cohesion and adhesion characteristics of the wet, sticky ore on physical modelling, experimental techniques and numerical implementation. Initially, the suitable bridging mechanism that contributes to the cohesive and adhesive forces within the iron ore material was identified (Hering, Martin and Stohrer, 1989; Rumpf, 1958). A cohesion/adhesion energy density factor based contact model was then introduced to describe the stickiness of the material. Secondly, an experimental system was proposed to directly test the stickiness of the material. Such a system is able to obtain both the cohesive/adhesive shear force and tensile force of the material at a specific moisture content. Lastly, the implementation of the proposed cohesion/adhesion model into the discrete element modelling (DEM) software was also discussed. A cohesion/adhesion calibration for modelling wet sticky iron ore in DEM was then conducted to ensure the material modelled in the simulation is reflective of the reality.From the study, understanding of the cohesion/adhesion characteristics of the wet iron ore material is significantly enhanced. Experimental and numerical outcomes can be directly applied for better designing or optimising the material handling processes that involve wet sticky iron ore. Consequently, the mining operating costs can be greatly reduced.CITATION:Chen, W, Donohue, T, Williams, K, Katterfeld, A and Roessler, T, 2015. Modelling cohesion and adhesion of wet, sticky iron ores in discrete element modelling for material handling processes, in Proceedings Iron Ore 2015, pp 387–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Won C. Park

Experiments showed changes in the mineral content of dolomitic oil shale at temperatures and exposure times which bracket conditions encountered during in situ retorting. Laboratory results correlate with cores from a spent in situ retort at Occidental's Logan Wash test site at Garfield County, Colorado. Dolomite, CaMg(CO3)2, decomposes rapidly to form periclase, MgO, calcite, CaCO3, and CO . Both calcite and periclase are intermediate products that can be stabilized by CO atmosphere at lower temperatures, while steam accelerates the formation 2 of silicates. The decarbonation of calcite appears to involve a direct reaction with both quartz and periclase in forming these silicates. Decarbonation preceeds the formation of akermanite, Ca2 MgSi 207, and diopside, CaMgSi 206, within several hours of heating and is followed by the nucleation of forsterite Mg2SiO4, and monticellite, CaMgSiO4. Under in situ retorting conditions, akermanite and diposide are the major minerals above 800°C. Equilibrium is not attained within 200-300 hours. In situ retorting temperatures above 800°C for extended periods of time should reduce potential ground water leaching by the formation of silicate minerals. These silicates are less soluble than free lime, magnesium or alkali oxides. There is a corresponding decrease in the natural pH of these silicates from approximately 12 down to 7.5 to 9:

Jan 1, 1981

By J. J. Demeter

As part of its work on converting coal to fluid fuels, the Federal Bureau of Mines has been studying the synthesis of liquid fuels from carbon monoxide and hydrogen by Fischer-Tropsch synthesis. A fluidized bed of nitrided, fused-iron catalyst has been operated successfully to produce high yields of oxygenated compounds. Trouble-free operation continued for over 800 hours, and the test was terminated voluntarily. About 85 percent of the fresh feed was converted when the unit was operated at a space velocity of 500 hr.-1, a 12:1 recycle-to-fresh-feed-gas ratio, a 300-p. s. i. g. pressure, and a temperature of 252° C. When operating at a fresh-feed-gas space velocity of 1,000 hr.-l and a 9:1 ratio of recycle to fresh gas, conversion of fresh feed was 68 percent, and the product yield was 235.9 grams per cubic meter of synthesis gas converted. The oxygenate and C5 and heavier hydrocarbon yield was 110.6 grams per cubic meter of gas converted, 83 percent of this was oxygenates. The atom ratio of N:Fe of the catalyst, initially 0.455, decreased to 0.288 by the end of the 800-hour experiment. Nevertheless, the yield of oxygenated compounds per cubic meter of H2 + CO converted at the end of the run was approximately the same as that obtained 500 hours earlier with identical operating conditions. X-ray analysis of the discharged catalyst indicated that only ?-iron carbonitride was present. Sieve analysis of the discharged catalyst indicated that only 2 percent of fines was produced during the reduction, nitriding, and synthesis.

Jan 1, 1959