Search Documents

By Thierno FALL

This paper describes the study of the work-roll during the hot rolling process thanks to a 3D model built with the Finite Element Method (FEM). In terms of computational cost, that method needs high resources compared to 1D model which are mostly used. However, the 3D model is built to have a better understanding of the work-roll thermal and mechanical behavior during the hot rolling process. The thermal model shows that the highest temperature reached during rolling are within the range of 500°C and 600°C. The thermal field input used to simulate the mechanical behavior of the work-roll shows a biaxial thermal stress state, in the circumferential and axial planes. However, a peak of radial stress is observed in the backup zone. It did not generate plastic strain but could influence the fatigue behavior of the work-roll.

Oct 1, 2019

By Hongshuang Di, Tianyu Zhang, Huiqiang Huang

A CMnSiAl transformation induced plasticity (TRIP) steel was used to study the effect of retained austenite on room-temperature mechanical properties. The steel plates with retained austenite were obtained by hot rolling, cold rolling and subsequent continuous annealing. The starting and finishing temperature of hot rolling are between Ac1 and Ac3. Reduction ratio of cold rolling is 75%. The continuous annealing is carried out at different intercritical temperatures. The relationship between work hardening exponent and retained austenite was discussed. The results show that, the Ac1 and Ac3 were much high because of the alloy elements, and the temperature range between them was wide. Due to the high hot rolling temperature, the grains was hereditarily refined as a result of dynamic recrystallization. Annealing at intercritical temperature of 930 ºC, retained austenite with relatively high stability reached a maximum volume fraction of 25%, a maximum total elongation of 30.2% and a best ultimate tensile strength × total elongation of 20.1 GPa·%. Instantaneous work hardening exponent reflects strengthening mechanisms at different strain stages. The TRIP effect of retained austenite is the main mechanism during deformation. With retained austenite of sufficient amount and high stability, continuous work hardening was observed in the tensile specimen of 930 ºC.

Oct 1, 2019

By Marcus Weldon

We are at the beginning of an era of profound transformation and human progress — a new industrial revolution. This “Automation of Everything” era will be brought about by digital interfaces, data analysis and control of the physical world through networks employing the Nokia Bell Labs Future X1 architecture — networks to support the digitization and connection of everything and everyone with the goal of automating much of life. The interconnection of robots, machines, drones, sensors, processing platforms and people through Future X networks will provide transformative tools for the automation and optimization of factories and warehouses, ports, electric grids, transportation networks, food, healthcare, construction, logistics and supply chain, emergency response, mining, and other physical industries. To date, the level of automation has been modest at best. Automating these physical industries — industries that account for 70 percent of the US Gross Domestic Product, for example — has the potential to drive significant increases in the world’s economic productivity.2 Realizing the potential of this next industrial revolution will require billions of wirelessly connected endpoints for high fidelity physical-to-digital conversion, millisecond response times to tightly control and coordinate machines and robots, and intelligent analysis to optimize real-time decisions — tasks beyond the reach of current networks. Increased levels of automation are already being achieved through the use of 4G advanced wireless access technologies. The untethering of sensors and actuators in industrial environments through the low-latency, high-bandwidth, high-reliability, and massive scale provided by 5G wireless access will complete this evolution, providing an unprecedented ability to digitize, analyze, comprehend and manipulate the physical world at a scale never previously thought possible. These new capabilities will enable us to create digital models of the physical world with ever higher levels of fidelity, further enhancing our ability to improve operational efficiencies and increase productivity and worker safety. Doing this will require a dramatic evolution in network architecture toward massively distributed cloud control and baseband capacity to achieve the required ultra-low latency and ultra-high bandwidth for industrial and infrastructure automation services — the Future X architecture. In early 2019, Nokia Bell Labs will publish a sequel to “The Future X Network: A Bell Labs Perspective”. “Future X for Industries: A Nokia Bell Labs Perspective” will explore how the Future X architecture will automate many of the world’s physical industries, including chapters devoted to electric power, cities, rail, mining, public safety, manufacturing, ports, logistics and supply chain, and an overarching chapter devoted to securing this highly automated world. To give you a small taste of the feast that’s to come, we’re sharing with you an initial installment — “Future X for Industries: Mining” — the Nokia Bell Labs view of how mining will be transformed through a Future X architecture..

Oct 1, 2019

By Wenting Zhu, Liqing Chen, Junjun Cui, Zhenye Chen

In this presentation, a low carbon high strength steel microalloyed with Nb and Ti was processed by thermo-mechanical controlled process (TMCP) containing two stages of controlled rolling. The austenite with various grain sizes was obtained by austenitizing this hot-rolled steel at different temperatures. And the effect of austenite grain size on bainitic transformation was investigated in a dilatometer to reveal microstructural change. The results showed that the microstructure of the hot-rolled steel was mainly composed of granular bainite, lath-like bainite, and martenite/austenite constituents (M-A constituents). With increasing the austenitizing temperature, or increasing the austenite grain size, the microstructure was changed from granular bainite to lath bainite. When the steel was reheated to a lower temperature of 860 ºC, a relatively higher start temperature (Bs) was measured for bainitic transformation. This was mainly caused by the formation of solute-depleted region in the austenite and the promotion of the granular bainitic nucleation. The highest reaction rate occurred at austenitizing temperature of 1000 ºC with fine grain size, while the coarse austenite grain can lead to a sharp increase in the amount of bainite. An analysis was made on the kinetics of bainite transformation which was controlled by the volume diffusion of C atom.

Oct 1, 2019

By Samuel Filgueiras Rodrigues, Clodualdo Aranas Jr., Gedeon Silva Reis, Eden Santos Silva, Fulvio Siciliano

When austenite is deformed above the Ae3 temperature, partial amount of it transforms dynamically into ferrite by a displacive mechanism. After unloading, it retransforms back into the stable austenite by a diffusional process. This influences the rolling load which decreases under isothermal condition or does not increase with decreasing temperature as rapidly as expected under cooling. Plate rolling simulations under isothermal and continuous cooling conditions were carried out on a 0.09 wt.% Nb X-70 steel. Pass strains of 0.2 were employed together with interpass times of 10 s, and 30 s for the cooling conditions and 0.3 with interval of 10 s at 900 °C for the isothermal experiments; strain rate of 1 s-1 was used during the simulations. The mean-flow-stress (MFS`s) behavior of both conditions indicates that dynamic transformation and dynamic recrystallization were taking place during straining. The critical strains for the initiation of dynamic transformation fell around 0.06 while the critical strain for DRX was 0.12. It has been shown that ferrite is formed due to the applied deformation of roughing passes and increases its volume fraction throughout the finishing rolling stage. Under cooling conditions, the ferrite formation is also favored as the temperature approaches the Ae3 line. Such ferrite forms when the driving force for dynamic transformation is higher than the total free energy barrier preventing its formation. This obstacle consists of the free energy difference between austenite and ferrite as well as the lattice dilatation work and shear accommodation work. The addition of Nb retards the retransformation of the ferrite into austenite. Moreover, holding times after rolling increases the amount of austenite available for microstructure control on subsequent stages. The dynamic transformation (DT) mechanism can be used to design improved rolling schedules

Oct 1, 2019

By Michael Breuer, Christian Mengel, Luis Acainas Caballero, Olaf Jepsen

Stability of the hot strip mill rolling process remains a main topic when it comes to processing thin and hard materials. Strip steering especially at the end of rolling and tail out rips are a main source of unscheduled down times in a hot strip mill. Main focus of this paper is the new X-Roll® Guide system to improve mill stability and quality. An overview of SMS group developments in the recent years regarding equipment and control strategies is given. The new side guiding system in the entry area of the finishing mill is introduced and explained with operational examples. The system provides reproducible conditions for the threading process and during rolling. Steering control has a direct benefit on the availability of the mill. New developments of the roll alignment control strategies based on roll force and mill stand entry guide force measurement will be presented. Additionally a camera based measuring system is introduced that generates a direct process feedback of the strip position. It provides together with the roll alignment control the necessary control parameters for adjusting the roll gap and guiding the strip correct centered through the mill. As a summary the SMS group system is explained combining all features.

Oct 1, 2019

By Gerhard Richter, Norbert Asamer, Gerwald Decker

At various stages during their manufacturing processes - from casting to finishing before delivery - semi-finished steel and special alloy products must be cut and surface-treated as well. The requirements for the individual conditioning steps, however, can be quite different. For example, the work piece can be hot, warm or cold. At any rate, the product must always be perfectly prepared for the next manufacturing step - reliably, in the shortest-possible time and at the lowest-possible cost. For cutting and grinding, BRAUN has developed innovative technologies and highly flexible, tailor-made solutions which meet these requirements in the most optimal way. In particular, BRAUN’s cutting and grinding technologies can also be used for large-scale products.

Oct 1, 2019

By Mingyu Ma, Lingling Liu, Liqing Chen, Houlong Liu

In this article, a 444-type heat-resistant ferritic stainless steel containing 0.05wt% Ce and 2wt% (Mo+W) was used as an experimental material and a study was carried out on the effect of rolling processes on the microstructures and texture evolution as well as on the mechanical properties and formability. The rolling processes contain hot rolling at different hot rolling finish temperatures, annealing after hot rolling, cold rolling and subsequent annealing. As for the hot rolling process, two hot rolling finish temperatures, 860 C and 770 C, were adopted, and their influence on the microstructures and mechanical properties was comparatively studied. The results showed that the microstructures after hot rolling and subsequent annealing could be refined by lowering the hot rolling finish temperature. The resultant microstructures after cold rolling and annealing were hereditarily refined. Lowering the hot rolling finish temperature can weaken the -fiber texture in hot rolled or cold rolled ferritic stainless steel strip. However, the -fiber texture was homogeneously strengthened by annealing the cold rolled ferritic stainless steel strip. Enhanced mechanical property and formability in terms of strength and average plastic strain ratio could be obtained by lowering the hot rolling finish temperature of ferritic stainless steel.

Oct 1, 2019

By Anand Kumar Agrawal, Kinzel Klaus Peter, Lorenzo Micheletti, Cristiano Castagnola, Horst Kappes, Andre Oliveira, Björn Rösner, Philippe Bermes

Blast furnaces are widely employed today for iron production all around the world, with a total production of around 1.2 billion tons per year. Its operating principle, which relies on usage of coke to reduce the ore, to ensure the permeability in the reaction vessel, to maintain its flexibility of operation and acceptability for varying qualities of iron ores. The blast furnace route is widely considered as the most economic and efficient route of iron production, however it is based on fossil energy carriers. The blast furnace route has undergone significant developments in terms of energy efficiency in the last decades, which led to a substantial reduction in the use of fossil reduction materials. Being an energy intensive process, competitiveness and cost saving in the blast furnace plant was always strongly related to the saving of energy and hence reduction of CO2 emissions. In addition to this, EU emissions trading system (EU ETS) as a cornerstone of the EU's policy in response to climate change has set new “challenges” for iron production in Europe. Paul Wurth has always been deeply involved in the development of energy saving technologies for blast furnaces. In the following a review of energy saving achievements developed in the last decades will be presented and the potential of available CO2 saving technologies will be summarized. Additionally, an outlook about the potential of future technologies, concepts and their impact on the blast furnace and the steel plant’s energy balance will be discussed. Finally, the replacement of carbon by hydrogen as reduction agent in the steel plant will be reviewed, with special focus on a comparison of costs and incentives.

Oct 1, 2019

By Johan PEERS, François DUMORTIER

Today, solutions to optimize Capital Expenditure (CAPEX) & Operational Expenditure (OPEX) for small capacity Cold Rolling Mills (CRM) as well as for high capacity CRM are available, as extensively described by various Original Equipment Manufacturers (OEMs) & steel makers. A suitable solution for small capacity CRM is to start with a single stand reversing mill (up to 400 ktpy, depending on product mix), which can then be expanded into a twin stand mill (up to 900 ktpy, depending on product mix). The main drawbacks in conventional practice are the off-gauge length in single stand set-up and the long downtime of the mill during the erection of the second stand. For higher productions CRM, it is common practice to directly select a new Pickling Line Tandem Cold Mill (PLTCM), with a high CAPEX. Is there an in-between solution that would allow to start with limited output and CAPEX, without jeopardizing the ultimate expansion goal (1.2 to 2 mtpy), for which PLTCM is the best techno-economical choice? In the absence of a solution, JOHN COCKERILL developed an integrated solution that limits the CAPEX in the first phase of development, without crippling affecting future endeavors through an easy and economically sustainable expansion into a PLTCM, without long production downtime. The solution consists of first installing a twin stand mill, expandable into a tandem mill thanks to a smart design of the line. It is therefore possible to limit the production to 900 ktpy in the first phase of the project and then convert the mill into PLTCM in the second phase to increase the production from 1.2 to 2 mtpy, depending on the market trends and financial capabilities. In summary, JOHN COCKERILL has developed a smart new layout in reversing phase combined with a brand new rolling strategy to optimize productivity and limit off-gauge, compared to conventional solutions (patents pending). In addition the layout enables an easy conversion to tandem mill without high over investments, which is more sustainable financially than the initial purchase of a PLTCM. Long downtimes to allow for capacity extension, detrimental to this phase-by-phase approach, are also avoided. Technical and process description of the new layouts and rolling strategies, together with CAPEX & OPEX descriptions of the phases are detailed in this paper.

Oct 1, 2019

By Afonso Cardoso da Silva, Romeu Thomaz Viana Jr, Emanuelle Garcia Reis, José Herbert Dolabela da Silveira

The Gerdau Ouro Branco Mill, three years after the implementation of its new plate mill, has started to develop high complexity products. The plate mill’s learning curve has been increasingly challenging since products are being developed to their highest grades. This work aims to present the first results of the development of steels of the strength class of 510 MPa produced by TMCP (Thermomechanical Controlled Processing) followed by accelerated cooling. These results show the potential and advantage of the accelerated cooling process regarding to obtain products of high mechanical strength and high toughness, associated with a low equivalent carbon.

Oct 1, 2019

By José Fagundes Jr., Juliano Braz Possatti, Bruno Câmara Vieira, Gabriel Godinho Alves, Bruno Bastos da Silva Murad, Cristina Maria de Oliveira Roque

Driven by market trends, increasing environmental accountability, government regulations and fostered by the Company’s strategic plan, ArcelorMittal Tubarão has developed new steel products to deliver better solutions to fit each customer’s needs. This often translates in higher strength, more complex and dimensionally challenging (thinner and wider) steels to attend a broad array of goals, such as reduction of vehicles fuel consumption and carbon emissions, increase in fatigue performance of heat treated parts, higher load capacity per net weight in vessels or wagons and lower supplying lead time as ArcelorMittal Tubarão establishes itself as a domestic option for so far imported grades. Based on the annual Product Development Plan, a structured workflow involves technical discussions from an operational point of view about safety issues, metallurgical project, steel grade family definitions, offline simulations prior to field trials, deformation resistance and process parameters adjustments and scheduling strategy. As a result of the increasing synergy between the areas, the share of new materials developed in recent years has been sustainably increased up to 15% in 2018, adding value to the final product without impact on hot rolled coil output and with a low cobble index.

Oct 1, 2019

By Débora Cardoso de Oliveira Silveira, Jean-Christophe Huber, Hamzeh Hamadeh, Kateryna Pastel, Guillaume Brosse

The dynamic behavior of oxygen gas flow, determined by the lance nozzle and blow pattern, is a key factor for determining jet efficiency in BOF Steelmaking. The present work compares the performances of Laval and parabolic nozzles with the aid of the Computational Fluid Dynamics (CFD). The Method of Characteristics (MOC) was applied to design a minimum length parabolic nozzle. The results show that the parabolic nozzle generates more uniform and stable jet, with 2% longer potential core and supersonic length and less shock waves. For the parabolic nozzle, the pressure nearby the nozzle wall is higher, which can protect this region from reverse flow of converter gases and offer longer life for the lance tip. Likewise, the flow rate variations would affect less this nozzle. In addition, the nozzle wear was investigated, and the parabolic nozzle has proven relatively less sensitivity to the presence of this deformity.

Oct 1, 2019

By Beatriz Pereda, Ana Clara Fonseca da Silva, Tiago Seixas Bittencourt

Reinforcing steel bars are usually specified based on mechanical properties with flexibility in chemical composition and processing. Most developments, in these steels, are normally focused on alloy and process design to reach minimum cost and conformity to specification. Processing routes using quenching and self-tempering (QST) and accelerated cooling are the most common. Microalloying with V and Nb have been used in rebar. When acicular constituents must be avoided, a combination of Nb microalloying with judicious control of cooling is one of the preferred options. Niobium can contribute to improvement in tensile properties through austenitic grain size control during hot working, precipitation hardening due to carbonitrides or clusters, and hardenability increase. In the present work the alloy design and development processes of a Nb microalloyed steel for rebars are presented. The designed steel has fulfilled the required specification and is under regular production. Austenitic grain size refining – when comparing with the “basic composition” normally used was observed, even without any change in the thermomechanical processing cycle. There are indications that precipitation hardening may also occur. Results indicate that Nb is a good alternative as a microalloying element in rebars.

Oct 1, 2019

By Richard Harvey, Robert Paul Mawer

In recent times there has been an increase in the demand from Steel plants for a technology that offers the most economical environmentally sustainable solution. In terms of blast furnace off gas cleaning this has seen a drive towards Cyclone technology replacing the older Dustcatchers. Cyclone technology can achieve dust removal efficiencies as high as 95% increasing the dust yield at the primary stage of gas cleaning. The dry dust (rich in Fe and C) can then be recycled to the Sinter Plant or Blast Furnace. Capture of dust at this stage also has the benefit that sludge generation from the secondary stage is also reduced meaning less waste to landfill and / or recovery of some of the by-products for further use. Primetals Technologies already offer a state of the art Tri-Axial Cyclone installed on many sites world-wide, however, this paper focuses on a hybrid of this technology, the DustClone. The DustClone is a low CAPEX unit that is essentially a Cyclone housed inside the Dustcatcher. This unit is aimed at operators who may be carrying out smaller scaled shutdowns / repairs that normally have a reduced CAPEX. This paper describes the technology that Primetals Technologies have developed.

Oct 1, 2019

By Wagner Viana Bielefeldt, Felipe Buboltz Ferreira, Antônio Cezar Faria Vilela

The continuous casting machine is one of the most important steel production steps in a melt shop. The tundish, a reservoir between the steelmaking ladle and the mold, has great influence over the steel cleanliness, along with the productivity bid. It must takes into account the quality of the metal and operational safety. Several different variables are related to the tundish process, of inclusionary cleanliness. Some of them are discussed in this paper: the free opening of ladle, tundish inertization, steel temperature in the reservoir and clogging formation, besides a brief topic about castability. Therefore, a critical analysis, with a review from some papers available in literature, is proposed in this study, with its focus on tundish.

Oct 1, 2019

By Lorenzo Bacchetti

Automatic yards with ad-hoc WMS (Warehouse management software), are the key for a modern and efficient warehousing which can face today logistic challenges. WMS boosts the traceability of material while optimizing the storage space. The operations in the yard are safer and logically organized according to algorithms that are specifically adjusted case by case. WMS can easily handle multi-cranes yard avoiding conflicts and increasing accuracy of positioning with decreased number of movements. The synergy of automatic cranes and WMS reduces bottlenecks and speeds up the preparation of deliveries with an overall improvement of warehousing and shipping scheduling.

Oct 1, 2019

By Ronaldo Esteves Ribeiro, Jefferson Felipe Faria Clemente, Carlos Victor Francisco dos Santos, José Herbert Dolabela da Silveira

n recent years, the market for thick plates has been highly competitive, in this scenario the plates quality is a critical success factor. In this process, the quality of the cut in thick plates is one of the important requirements for the customers, by the visual aspect as well as the technical aspect of the plate application. In the shear line, the cutting is done by shearing to trim tips, subdivide plates, trim side edges, remove samples, eliminate defects, etc. The cut is obtained by the penetration of the upper knife in the plate, causing plastic deformation in a certain region and hardening. If the clearance between the knives is adequate, the cracks will be close to the centre of the plate thickness and will result in a good cut quality. This work will present the theory of cutting of thick plates, the types of shearing, the quality of the edge in the cut, the types and the main characteristics of the knives.

Oct 1, 2019

By Karl K. Bagger, Felipe Bertelli

The competitive scenario of steel industry requires studies and developments to improve manufacturing processes focusing on increasing productivity and reducing costs. The practice of coating rolls for cold rolling with the chrome aims to increase the rolling campaign, reducing their wear by increasing the surface hardness, which guarantees a greater homogeneity in the surface of the rolled products. The present paper presents a study on the effect of the chromium coat on a forged steel rolls on the wettability of a SkinPass solution. The hardness of the coated layer and the contact angle were measured for two concentrations of solution on two types of surfaces, comparing the coated and uncoated surfaces. The results show that there is an influence of the coating on the wettability of the fluid when comparison are made with chrome coated and uncoated materials, being verified through tests in Goniometer. The productivity of the coated rolls showed higher productivity than the uncoated ones.

Oct 1, 2019

By Pierre Montmitonnet, Yukio Shigaki, Jonatas Mezêncio Silva

A precise roll stack deformation model of a flat rolling mill is crucial for strip profile assessment as it depends strongly on the roll’s deformation. The need for more and more advanced products with stringent both geometrical and mechanical tolerances (e.g., Advanced High Strength Steels – AHSS), with thinner and harder steel strips, demands more advanced simulation models. The present paper addresses assumptions made in Finite Element Method (FEM)-based roll stack models on some important, yet barely discussed features: What is the impact on precision of the simplifications such as symmetry and anti-symmetry? Should roll neck boundary conditions in bearings be considered as fixed or simply supported? In this paper a hybrid model developed by the authors for a general flat rolling mill is used to assess those questions. This model runs much faster (100x in some cases) than a whole-FEM-modeled 6-high rolling mill with the elastoplastic strip deformation, thanks to its simplifications adopted. This model assumes a steady state rolling condition, and the roll stack is modeled with tridimensional finite elements, and the loads are calculated via a slab method adopting a plane strain state for the strip deformation (especially true for thin strips). An industrial 6-high cold rolling mill is modeled and results on the application of symmetries and different boundary conditions on the roll’s necks are presented. It is concluded that the application of symmetries and anti-symmetries for the 6-high rolling mill is possible for thin strips. And the way the necks are modeled does not impact on the final strip shape, though it influences the magnitude of the roll’s displacement. The coupling of the strip with the work roll applied assuming a symmetry plane of the arc of contact has little influence on the strip shape.

Oct 1, 2019