Search Documents

By Thomas M. Barczak

This U.S. Bureau of Mines study evaluates factors that influence longwall support and strata interaction. The longwall system is composed of an immediate and main roof structure and three supporting foundations: longwall panel, powered roof supports, and gob waste. The main roof forms a structure that is generally supported by all three foundations, while the immediate roof acts as a beam that cantilevers from the coal face to the powered support. In most cases, shield loading involves a complex interaction of both main roof and immediate roof behavior and is a combination of loads produced from convergence of the main roof and displacements of the immediate roof caused by deformations of the cantilevered roof beam. Since the shield stiffness remains constant for all leg pressures and main roof convergence is irresistible in terms of shield capacity, the shield must be able to control the behavior of the immediate roof or floor structure for shield loading to be sensitive to setting pressures. If the goal is to minimize total shield loading, any active setting force must be offset by reduced passive shield loading to justify the active setting loads. Field data sumest that the typical reductions in passive loading do not justify the required increases in setting pressure in some applications.

Jan 1, 2010

By B. Seymour

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop safe practices for the use of shotcrete as ground support in underground mines, particularly mines operating in weak host rock. As part of this research, tests were conducted with a commercial poly-fiber reinforced shotcrete mix to develop a practical means of measuring shotcrete adhesion strength. Full-scale tests were conducted in a test frame equipped with concrete panels having three distinct surface roughness profiles. Adhesion test fixtures either embedded or epoxied in the shotcrete were overcored into the underlying concrete, and direct tensile tests were conducted to determine the bond strength of the shotcrete cores to the substrate after a selected shotcrete curing interval (1, 3, 7, 14, 28, or 90 days). Measured adhesion strengths typically ranged from 0.5 to 2.0 MPa depending on the curing age of the shotcrete samples. This paper presents the results of these tests, describes the portable test system components, and addresses some of the design issues encountered in the development of a rugged and reliable method for determining shotcrete adhesion strength in underground mines.

Jan 1, 2010

By P. L. Sibrell

Previous research by the U.S. Bureau of Mines has shown that autoclave cyanide leaching of used automobile exhaust catalysts for recovery of platinum-group metals (PGM) is technically feasible. The purpose of this work was to investigate the chemistry of the dissolution of PGM in cyanide solutions in more detail. Where possible, samples of pure, elemental PGM powders or foils were used instead of automobile exhaust catalysts, because of their greater purity. Ultraviolet spectra revealed that Pt and Pd were solubilized as the square planar tetracyanometallate (II) complexes, while Rh was solubilized as the octahedral hexacyanorhodate (III) complex. This explained the poor recovery of Rh from solution by carbon adsorption, solvent extraction, and ion exchange observed in earlier research, because of the higher anionic charge and size of the octahedral complex. Leaching rate studies showed that the rate of solubilization was greatest for Pd, followed by Pt and Rh. Although the rate of chemical reaction was the controlling step for the dissolution of elemental Pt and Rh samples, the rate of pore diffusion was rate limiting for PGM in catalyst samples.

Jan 1, 2010

By F. H. Nehl

The U.S. Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu codeposited. Decreasing Cu codeposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.070 A?h per 150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 ms. Graphite, lead, and stainless steel were evaluated as electrode materials. Square wave electrowinning at 70° C gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10 to 30 pct, and a period of 100 to 1,000 ms gave the following results: Ag concentrations decreased from 34 to 0.1µg/mL, Au concentrations decreased from 54 to 0.2 µg/mL, and Cu concentrations remained almost constant at 560 µg/mL.

Jan 1, 2010

By R. J. Folic

Investigations of the vibrations of a pile in soil are performed on a dynamic model in the form of a prismatic bar of finite axial and flexural stifnesses with a discrete mass at its free end representing the cap. The soil is represented by a system of springs of constant and variable stiffnesses. Oscillation differential equations are derived by means of the Hamiltonian principle for non-conservative systems. The problem is reduced to a coupled system of two non-linear partial differential equations with corresponding initial-boundary conditions. Frequency equations of longitudinal and lateral linearized equations are formed. The paper determines natural frequenc­ies and oscillation modes. It separately examines longitudinal vibrations excitated by a hermonic force acting upon the pile cap, and lateral vibrations excitated by an impulse acting upon the cap. The results of the numerical processing are presented in respective diagrams in dimensionless form.

Jan 1, 2010

By Gary L. Hundley

As part of the U.S. Bureau of Mines program to reduce the Nation's reliance on foreign supplies for critical metals, a procedure was devised to separate and recover critical metals from mixed and contaminated super alloy scrap. The process uses both pyrometallurgical and hydrometallurgical methods to treat the scrap. The mixed scrap is converted to a matte containing 4 to 7 pct S by adding S directly to the molten metal. This matte is then granulated and ground to a minus 35-mesh particle size and leached with an HCI-CI2 solution. This process takes essentially all the Ni, Co, Cr, Fe, AI, and Mo into solution in a 3-h leach, leaving W, Ta, Ti, and Nb (Cb) in the residue. The Mo is recovered from the chloride leach solution by solvent extraction, and the Cr and Fe are recovered together by precipitation. The Ni and Co can be recovered individually by an existing solvent extraction-electrowinning process. The W is recovered by a caustic leach of oxidized Cl2 leach residue.

Jan 1, 2010

By G. A. Kordosky

There are a number of reasons why the solvent extraction of molybdenum deserves attention: 1. The solvent extraction chemistry of molybdenum is interesting and complex, 2. The price of molybdenum is predicted to average about US$ 20.00 / pound in 2010 and, as China, India and other countries develop, the demand for specialty steels will increase putting long term demands on molybdenum supply, 3. Uranium ores often contain significant concentrations of molybdenum[1] and typically yellow cake will have a moly specification which when exceeded brings penalties, and 4. The valuable metal rhenium is a byproduct of molybdenum recovery circuits.

Jan 1, 2010

By Raj Thamburaj

"Over the last few decades, the emphasis on affordability and reduced cost of ownership has necessitated the development of innovative processes to carry out repairs in aero engine components. Conventional weld and braze repairs have evolved into advanced, sophisticated processes using state of the art knowledge in lasers, robotics and materials technology. This paper illustrates past and present scenarios in an attempt to illustrate progress that has been made in this area. The problems encountered in the past have been detailed along with the solutions that have been developed and commercially implemented to address these issues. Apart from technical progress, this presentation also addresses the progress made in business approaches and in Certification/Regulatory issues surrounding aero engine repair. Progress in Technology Repair technologies have also been the embryo from which new and revolutionary manufacturing technologies have evolved as well. Electron Beam Free Forming and LENS are examples of how a completely new manufacturing concept can evolve what was originally only a process to join metals. The current and future potential of these spin offs is discussed providing examples of application. While several problems have been solved over time with the implementation of advanced repair technologies, the demands of the industry have created new challenges. The paper describes these issues, outlines potential solutions and discusses the future of repair technologies in terms of the far reaching influence it is sure to have in design, manufacturing, maintenance management and life extension. Progress in Business Trends.Business approaches to repair and maintenance have also gone through considerable change with the introduction of ""Power by the Hour"" and other similar arrangements between the companies responsible for engine overhaul and the end-users. Program Based Logistics (PBL) is yet another innovation to provide a win-win situation for the repair service provider and the end user. This paper traces the development of these business initiatives and highlights successful applications. Progress in Repair Certification, Regulatory Issues.Understanding of the issues surrounding certification of repairs has also evolved with time and regulatory issues have been clarified considerably. Procedures for analysis and testing are much clearer and ""Check Lists"" are being drafted for certifying repairs on various engine components. The PMA phenomenon has added yet another dimension to the issues regarding certification and these are discussed as well."

Jan 1, 2010

By Kwang-Yeom Kim, Dong-Gyou Kim, Hyo-Kwan Yoon

This study was intended to simulate the blasting model using notched-hole with numerical approach. Numerical analysis approach was applied to compare and evaluate the blasting model using notched-hole and circular hole. To implement non-linear dynamic blasting model, blasting analysis was carried out with AUTODYN code. Behavior of two models was compared and evaluated using AUTODYN and visual analysis and quantitative evaluation based on pressure and stress to verify the effect to induce the destruction territory to the specific direction when blasting with notched hole was attempted.

Jan 1, 2010

By A. E. Petersen

To reduce U.S. dependence on imports of titanium, the U.S. Bureau of Mines has investigated the recovery of titanium from perovskite (CaTi03). Domestic perovskite deposits represent a significant, but untapped, titanium resource. An acid sulfation method was developed that will extract about 97 pct of the titanium and the columbium and 70 to 90 pct of the rare-earth byproducts from perovskite concentrates. A flow-sheet for recovering titanium as pigment-grade titanium dioxide (Ti02) is discussed. Test work performed in developing each unit operation is described. The first three unit operations have been demonstrated using laboratory-scale continuous methods of operation: acid sulfation of perovskite concentrates, leaching sulfation residue to dissolve metal values, and precipitation of titanium oxysulfate monohydrate (TiOS04?HP) from the resulting leach flltrate. Batch testing of other unit operations was performed: TiOS04?H20 redissolution and iron reduction, precipitation of Ti02 by hydrolysis, and regenerating recoverable acid with rare-earth byproduct recovery. Cost evaluation results are provided, indicating that processing perovskite concentrates by acid sulfation may be an economically viable means of producing Ti02.

Jan 1, 2010

By A. L. Martikainen

Booster fans increase air pressure to overcome resistance, the objective being to force adequate amounts of air through distant workings. They are used in areas that are difficult or uneconomic to ventilate with main fans alone. Booster fans are currently permitted in underground coal mines in some countries; the United Kingdom, South Africa, Australia and Canada have been defined as major users. Booster fans are not allowed in the US bituminous and lignite coal mining operations at the present time due to safety concerns. This paper presents the history of booster fan use in coal mines of the United States during the last 90 years. Changes in regulations, as well as advantages and disadvantages of booster fan use, are discussed. Research and petitions for booster fan use are highlighted in order to bring the debate into focus.

Jan 1, 2010

By H. W. Kilau

The U.S. Bureau of Mines is evaluating water spray additives for the purpose of improving respirable dust control during coal mining operations, with particular emphasis on the longwall shearer. Recent field tests of surfactant-polymer reagents at two production longwall operations have shown favorable respirable dust reductions compared with water sprays containing no additive. Gravimetric dust samples obtained by a technician downwind of the shearer while following or preceding the machine showed dust reductions in the range of about 40% to 60% for some of the reagent formulations compared with using water alone. Three polymers were tested: two polyethylene oxide compounds of different molecular weight and hydroxypropyl methylcellulose (HPMC). All were effective for dust reduction, and two were cost effective when used in combination with sodium di(2-ethylhexyl) sulfosuccinate surfactant. How-ever, the use of these reagents requires the longwall operator to be more aware of headgate dust control. Experimental evidence indicates that dust captured by reagent-treated sprays at the shearer can be reemitted in the headgate area if stagcloader-crusher sprays and other dust controls are inadequate.

Jan 1, 2010

When science and the human spirit come together amazing things can happen. This was perhaps never more evident than through the events that unfolded during August and October in a remote desert in northern Chile. On Aug. 5, the main shaft of the San José copper and gold mine near Copiapó in Chile?s Atacama Region collapsed, leaving 33 miners trapped more than 624 m (2,000 ft) beneath the earth?s surface.

Jan 1, 2010

By Dale Preece, Joergen Pilz, Zavis Zavodni

An overland conveyor was constructed at a surface coal mine to reduce the truck haul distance and make the operation more efficient. An important element in this system is a truck dump facility to transfer coal from truck to conveyor. Mechanically stabilized earth retaining walls were employed to accommodate the coal processing equipment, including the crusher, in this facility. These retaining walls are close enough to the pits being mined that blasting induced vibrations must be considered in analyses of the wall structural stability.

Jan 1, 2010

By Dale Zacherl, Andreas Buhr, Rainer Kockegey-Lorenz

"The microporous calcium hexaluminate insulating material SLA-92 has been introduced as an alternative to refractory ceramic fiber and other insulating refractory materials. Key properties associated with this product include: high chemical purity, long term high temperature stability up to 1500 °C, low thermal conductivity up to 1500 °C, and high thermal shock resistance. The properties of the new material and various applications in the steel and ceramic industries have been reported in previous papers. The current paper summarizes the industrial application experiences with innovative refractories based on SLA- 92 and discusses potential new applications in various manufacturing as well as energyrelated industries.IntroductionSLA-92 was introduced to the refractories industry in 1998 by van Garsel, et al. [1] as a new insulating raw material for high temperature applications, followed by investigations [2] of long term temperature stability for this new lightweight aggregate up to 1500°C.SLA-92 was developed as an innovative alternative to commonly used refractory ceramic fibers. It has unique properties regarding chemical purity and mineral composition and is a microporous, silica-free calcium hexaluminate (CA6 – mineral name: hibonite)."

Jan 1, 2010

By Gerrit V. R. Goodman

Future coal mining systems will be able to cut from crosscut to crosscut where advances could exceed 100 ft. However, limitations arise when ventilating such mining systems. In deep advance mining, there would be no workers at the face to advance ventilation tubing or curtain manually. Traditional methods also provide no means for maintaining face ventilation after the miner backs away from the face. U.S. Bureau of Mines research is studying means to provide effective ventilation at cut depths beyond the current limit of 4D ft. Several innovative ventilation schemes are currently being considered. One such method is the use of a jet fan to ventilate a deep cut. A jet fan is simply a freestanding fan using little or no ducting to direct the ventilation flow. Jet fan testing in a 90-ft entry revealed that higher exit velocities and greater penetration depth occurred when various configurations were used to confine and direct the air flow. Additional testing also indicated that 2,200 cfm of fresh air was delivered to the face? 90 ft distant when a check curtain was used to limit entrainment around the fan. Without this curtain, this quantity dropped to only 1,000 cfm. This testing indicated that a jet fan was capable of providing ventilation to a distant face area. It also highlighted potential problems, such as recirculation at the fan and reentrainment in the jet flow. Despite these potential problems, jet fans may be adequate for ventilating cuts exceeding 4D ft.

Jan 1, 2010

Thermal barrier coating (TBC) systems provide thermal insulation to high temperature for aero¬propulsion. A fracture mechanical model developed earlier for multilayer systems is applied on TBC to realize superior performance by enhancement of fracture resistance. Functionally gradient materials (FGM) solution concept is the basis of approach followed here. A few realistic FGM TBCs are considered in the analysis in addition to a conventional TBC as the base case and a hypothetical worst case with YSZ-YSZ interface. Parameters like number, composition and thickness of graded layers and elastic modulus are considered for the analysis and quantitative improvement of fracture resistance of TBCs. The analysis is confined to deep crack with crack size to width ratio as 0.5.

Jan 1, 2010

By E. T. Pecina

Bioleaching is a viable option for the processing of auriargentiferous refractory ores with high arsenic content. The application of mesophilic (A. ferrooxidans and ?L. ferrooxidans?) and thermophilic bacteria of the genus Sulfolobus (S. solfataricus and S. acidocaldarius) as oxidant treatment before the cyanidation of an industrial arsenical pyrite concentrate is presented. The results show that extraction of gold and silver increases due to bio-oxidation caused by mesophilic bacteria and results in a maximum gold recovery of 68%. In all strains studied, biooxidation resulted in an average silver recovery of 50%. The results showed that all evaluated strains were sensitive to solids content (5 to 20%) and average particle size (75 and 38 µm) of the concentrate.

Jan 1, 2010

By W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at, the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-clement method for the evaluation of shaft pillar mining plans and shaft stability. This report, one of three in a series describing the Ross shaft pillar case study, focuses on the premining stability analysis. The two-dimensional computer program UTAH2 was used in advance of pillar mining; results suggested that the shaft would remain stable. Subsequent reports describe parts 2 and 3 of the study. In part 2, borehole extensometers and other instruments were installed to provide data for model verification and shaft monitoring. Results of the recalibrated two-dimensional model confirmed the premining stability evaluation. However, after mining began, great concern developed because of the appearance of cracks and other signs of ground movement over considerable distances from the area of active pillar miping. In part 3, an intense three-dimensional modeling effort using UTAH3 was initiated. The results again showed that the shaft would remain safe. Three-dimensional analyses of alternative pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought.

Jan 1, 2010

By Andrew B. Cecala

The U.S. Bureau of Mines has designed and evaluated total mill ventilation systems at two different mineral processing operations. Both systems have proven very effective at reducing respirable dust levels throughout the mill in a cost-effective manner. A 25,500-cfm system installed at a clay processing mill provided approximately 10 air changes per hour. This system reduced respirable dust concentrations by approximately 40 pct throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 50,000 and 100,000 cfm of ventilation to the mill building, corresponding to 17 and 34 air changes per hour. Average mill-wide respirable dust reductions were 36 and 64 pct, respectively. Not only did these systems reduce respirable dust concentrations and increase visibility throughout the mills, they were also easy to install and required minimal maintenance. A total mill ventilation system provides a general purging of the mill air; the system should be viewed as a supplemental technique to assist other dust control systems in operation.

Jan 1, 2010