Search Documents

By N. Novikov, M. Jastrzebski, N. Kryzhanovskaya, D. Shevchenko, I. Kapran, N. V. Novikov, T. Koehler, B. Zaporozhets

"The PFK FeNi Smelter was re-commissioned by Solway Resources in 2002, ending a long period of economic decline in the adjacent town. In 2009 Hatch was retained to design, supply and install a custom furnace crucible that would accommodate a capacity increase from 34 MW to 40 MW and increase campaign life through binding and cooling technologies, as part of ongoing improvement efforts. The involvement of PFK personnel was critical to the successful integration of the new furnace technology with the existing process and operational practice. The furnace upgrade project was completed in 18 months during 2010 – 2011. Since start-up, the furnace has exceeded production expectations, operating successfully at 42 MW.INTRODUCTIONAfter ceasing operations in the 1990’s, the Pobuzhsky Ferronickel Combine (PFK), located in central Ukraine, was stripped of useful equipment and deteriorated while dormant. The surrounding town experienced a period of economic decline throughout the 1990’s. Solway Industries purchased the complex in 2002 and began a systematic incremental program to re-commission the smelter using both local expertise and specialists from other parts of the former Soviet Union. This led to the re-birth of PFK as a successful toll-smelting complex, and a renaissance for the surrounding economy.As part of the continuing improvement program, PFK approached Hatch in 2009 to study the possibility of a capacity expansion from 34 MW to 40 MW. It was decided, based on the results of the study, to design and install a custom furnace crucible integrating the unique PFK FeNi process with modern Hatch furnace technology. This novel approach had many benefits, including: maximum re-use of existing furnace components (off-gas, feed equipment and transformers), minimal impact on upstream and downstream equipment and building structure, and the retention of a familiar operating regime. The latter was a key factor in the success of the project, as it allowed the extensive operating expertise of the PFK staff to remain highly relevant to the upgraded furnace. This led to minimized capital investment, a rapid start-up and no significant operational challenges switching over to the new equipment incorporating Hatch furnace technology."

Jan 1, 2012

"Some of the tools developed for the processing of nickel laterite ore by resin-in-pulp (RIP) may be applicable to the remediation of metalliferous mine drainage (MMD). In both cases, recovery of metal value and production of a stable waste stream appropriate for long term storage is desired. MMD typically has the additional challenge of management of toxic low-value metals. Seen in this light, innovations in RIP reactor configuration, selective elution strategies and novel synthetic ion exchange resins become useful tools for taking on the MMD challenge in a way that maximizes both environmental and economic benefit. INTRODUCTIONAcid mine drainage (AMD) is a common problem in any country with significant past mining activity. When sulphide containing minerals, tailings or slag are exposed to water, oxygen and sulphur oxidizing bacteria, AMD will result. Abundant and reactive iron sulphide minerals leach first, providing acidity and the ferrous/ferric couple that can enhance the oxidation kinetics of other minerals. If this runoff contacts encounters acid consuming carbonates or silicates, the acidity may be neutralized, but certain heavy metals remain in solution and can continue to be an environmental hazard (Gray, 1997). For this reason, the remainder of this paper will refer to the broader term metalliferous mine drainage (MMD) rather than acid mine drainage. In either case, such drainage, containing high heavy metal concentrations and often significant acidity, is toxic to aquatic life and can lead to significant damage to ecosystems and to public watercourses. MMD is a problem most commonly associated with now defunct sulphide mineral mines, but similarly toxic streams can result from many types of waste, such as poorly stabilized leach tailings, slag heaps, and coal flotation tailings (Johnson and Hallberg, 2005; Lee et al., 2002; Sainz et al., 2002; Schüring et al., 1997). In any case, the management and remediation of MMD is an important ongoing problem for the resource industry, particularly for the many mines in Canada closed before the advent of more stringent environmental standards. MMD remediation represents a significant long term expense for the resource industry. Multi-disciplinary efforts to understand and mitigate this problem range from creation of artificial wetlands (Poulin and Lawrence, 1996; Sheoran and Sheoran, 2006) to sophisticated biochemical reactors and precipitation processes (Hatami, 2010). Certain remediation technologies such as ion exchange offer methods to make a saleable product by recovering valuable dissolved metals. This paper will show how these technologies can help defray the cost of remediation, and offer potential to turn a dangerous waste stream into a useful product."

Jan 1, 2012

By C. Edwards

ABSTRACT: Milling operations in northern Saskatchewan’s Athabasca Basin have produced uranium continuously since 1975. During that period, the Athabasca Basin has been one of the world’s premier uranium camps, yielding more than 660 million lb (299,370,964 kg) of U3O8. In this paper, the author describes former and current milling operations and discusses why and how the milling process has changed and developed over the past 35 years. The author’s considerations for the future of uranium extraction in the Athabasca Basin conclude the paper.

Jan 1, 2012

By Muamer Medusalic, Kim Henley, Lucas Bottomley

The period from 2009 to 2012 has witnessed a large rise in the number of blast-generated fume events in Eastern Australia, where highly visible oxides of nitrogen (NOx) are produced from coal mine blasting. Fume production mechanisms have been poorly understood by mine operators, and practical measures to reduce fume were initially elusive. Over time, data on fume events has been collected and analysis has pointed to a range of contributing factors associated with fume production.

Jan 1, 2012

By Nickolas Vlahopoulos, Nicholas Stowe

A concept has been proposed for the focusing of underwater energy. An array of spherical TNT charges is used to achieve this aim. The goal of the present research effort is to model such a system and identify optional arrangement and detonation timing schemes. A fast-running model is necessary to perform optimization analysis due to the highly iterative nature of most optimization algorithms. This requirement renders the use of sophisticated numerical solvers impractical. An analytical, physics-based model must be developed to satisfy the demands of the multiple charge optimization problem. This model must capture shock propagation speed, pressure-time histories throughout the fluid domain, and multiple charge interaction phenomena. Such a model is presented herein.

Jan 1, 2012

By Sudarshan Martins

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By J. Jung, W. Keller, A. Zucht

"The agitator design for nickel high pressure acid leach autoclaves (HPAL) is critical with regard to the process result, i.e., the recovery rate. Further considerations during the design phase are the avoidance of acid hot spots which reduce the lifetime, due to corrosion of the wetted parts, including components manufactured from titanium. Besides the process knowledge to design HPAL autoclaves, tools such as, Computational Fluid Dynamics (CFD) supplemented by lab testing allow the design of optimized agitation systems. This paper describes the effect that different feed point locations have on instantaneous blending of the reactants. Furthermore, experiments and CFD show where abrasion issues might occur and how to obtain information about the static and dynamic forces acting on internals. We show how simulations can be validated by lab testing to ensure that the CFD models are applied in an appropriate way.INTRODUCTIONAgitated systems in hydrometallurgical processes have to comply with multiple process tasks and in many cases have to withstand extreme operation conditions such as pressure up to 50 bar, elevated temperatures of up to 250°C and exposure to very acidic or alkaline environments and abrasive ores. The process tasks range from instantaneous mixing of reactants, homogeneous suspensions of up to 65% wt. solids with coarse and heavy particles, enhancing the solid-liquid mass transfer for leaching, dispersing large volumes of reactants (gas-liquid, liquid-liquid mass transfer) and moreover to transport generated heat e.g., from exothermic reactions through the vessel walls or internal heat exchangers if required. For economies of scale, agitator systems have reached sizes of 5000 m³ for large open leach tanks with impeller diameters of approx. 6 m, while autoclaves nowadays have exceeded 5.5 meters in diameter with a power demand for a single compartment drive between 300 - 400 kW. In parallel all process industries require a more efficient use of resources, to generate less by-products and higher yields, while ore-bodies tend to be less qualitative and new process routes (e.g. direct leach) are developed. Besides all these facts the mixing solution must be robust and economic. In this paper we want to address our approach in the development and designing of HPAL agitation equipment."

Jan 1, 2012

Since its creation in 1910, the Department of the Interior's Bureau of Mines has pioneered in the development of mineral technology, through research. From the very beginning, research on mine health and safety has been a dominating concern, and a responsibility that expanded markedly as a result of the Coal Mine Health and Safety Act of 1969. Until the mid-1970's research on fuel technology and coal production also was an important part of the Bureau's work. But in the four years following the 1973 oil crisis, Congress established a reorganized Federal energy research apparatus in which all fossil fuel research-encompassing extraction, use, and conservation-was centralized. Today, the Department of Energy houses Federal research on coal mine production technology, while research on coal and noncoal mine health and safety and environmental technology, and on noncoal mine production technology, remains in the Interior Department as a continuing responsibility of the Bureau of Mines. In carrying out its authorized research programs, the Bureau conducts both short- and long-term re-

Jan 1, 2012

By Scott Ellenbecker

Mining has evolved in recent years, taking steps forward in the way that the industry is considerate of the environment and the communities in which it operates. Technology plays a major role in that evolution. Osisko Mining?s Osisko Mine near Malartic, Quebec is developing a new way of doing business. One manager said, ?We are building the Osisko culture,? but the company is doing many things that could become industry changers. Much of the change is driven by mine ownership and management to offer a better workplace and better community relations. Mining equipment manufacturers are changing, too, by engineering products with more operator comfort, fuel economy, ease of maintenance and more cleanly designed machines. And for those drills working close to communities, smaller bore sizes and sound retention are just two changes for the better.

Jan 1, 2012

By Edward Rybinski

Compañía Minera Antamina is a polymetallic mining complex that produces copper and zinc concentrates as primary products and molybdenum and lead/bismuth/silver concentrates as by-products. In 2007, Metso Process Technology and Innovation (PTI) was contracted to increase SAG mill throughput by integrating and optimising blast fragmentation, crushing and grinding for the harder M4/M4A (CuZn) ores. Following the implementation of recommendations provided by Metso PTI, the SAG mill throughput increased from 2750tph to reach an average of 3600tph for the remainder of 2007. Due to continued application of mine to mill integration and optimisation philosophy, by 2010, the concentrator consistently exceeded the target of 4400tph while processing harder CuZn ores.

Jan 1, 2012

By U. Thorley

This paper presents an overview of surface mining activity in the Canadian oil sands and how the mine operators interact with the province of Alberta's Mine Financial Security Program (MFSP), which took effect April 1, 2011. The MFSP approach to reclamation assurance results in the government of Alberta sharing a portion of reclamation liability through the majority of an oil sand mine's life. In order to determine the potential fiscal magnitude of this shared liability, an examination of the expected costs of oil sands reclamation activities through a study of corporate asset retirement obligation (ARO) liabilities and other corporate disclosures is presented. The province of Alberta's Environmental Protection Security Fund (EPSF), which formerly secured oil sands mine reclamation activities is discussed. Reclamation costs in the oil sands are poorly understood. The MFSP provides what it characterizes as a conservative estimate of C$75,000/ha, while corporate disclosures by Canadian Oil Sands Ltd. place expected costs at C$180,000/ha. There is significant risk associated with the apparent uncertainty surrounding reclamation costs.

Jan 1, 2012

By E. Asselin, P. Sauve, H. Salomon-de-Friedberg

"Residues from the CESL Copper process were leached using the CESL Gold process. The kinetics of reaction were confirmed to be fast with over 50% of the gold consistently extracted within 2 minutes of leaching. Final gold extractions under the conditions tested here were between 80-90% obtained within 90 minutes. A model for the CESL Gold process was developed. This model is slightly different based on whether the copper concentrate leach residue was ground or unground prior to leaching: the gold leaching rate constant is approximately twice as fast for the ground samples. Unground residues had a P80 of 13 ?m whereas ground residues had a P80 of 10 ?m. The model predicts a 43% decrease in leaching time for ground residue versus unground residue to achieve the same extraction under otherwise identical conditions. The model was more accurate for the ground samples. INTRODUCTIONTeck's CESL Process (Jones, 1996) was developed to provide an economically attractive alternative to traditional copper smelting. It has since evolved to also deal with copper concentrates containing valuable impurities such as nickel and undesirable ones, such as arsenic, while reducing downstream costs. Effective recovery of gold and silver is essential to the economics of the CESL Process. The Brook Hunt 2007 copper concentrate assay data (Wood-Mackenzie, 2007) were examined to determine the ratio of gold plus silver value relative to the contained copper. As indicated in Figure 1 below, nearly two-thirds of concentrates have 10% or more of their total value tied up in their precious metals content.CESL has extensively examined the recovery of gold and silver at bench, pilot and demonstration scale, which has culminated in the present CESL Gold Process (Barr et al., 2007). The process targets the precious metal contained in the leach residues produced in the copper portion of the flowsheet. This residue has two primary components which influence downstream processing. The major iron-rich fraction (-75 wt%) of the residue is a mixture of various forms of iron oxide precipitates including hematite and jarosite (Sahu and Asselin, 2011). The iron fraction ranges from amorphous to crystalline in nature depending on the compound precipitated, upstream operating conditions and feed material composition. The lesser, but by no means less important, fraction is a mixture of elemental sulphur and unreacted sulphides (principally pyrite).Elemental sulphur formed during the oxidative leach of the copper concentrate reacts with cyanide to form thiocyanate (SCN-) making a traditional cyanide leach approach too costly. Since the SCN formation reaction strongly depends on contact time with the CESL residues (Po, 2007) short contact times were preferred. This factor guided the development work towards the eventual room temperature, pressure cyanidation process which results in near complete gold dissolution in 90 minutes. A recent CESL gold demonstration campaign treating 1.5 t/d of residue from the copper oxidation step achieved an average gold extraction of 91% (96% maximum)."

Jan 1, 2012

By Lv Guozhi, Niu Liping, Liu Yan, Zhao Qiuyue, He Jicheng, Zhang Ting’an, Dou Zhihe

"This paper proposed a new method of Mg and Cl2 circulating for titanium sponge production by direct pyrolysis and thermal reduction process. Effects of pyrolysis temperature, pyrolysis time and partial pressure of oxygen on pyrolysis efficiency were researched, and the crystallite structural transformation of MgO productions at different pyrolysis temperature and time were analyzed by XRD. The experimental results indicates that the pyrolysis temperature and time effects the pyrolysis efficiency obviously, and the reasonable pyrolysis conditions by using MgCl2 in molten state are as follows: the pyrolysis temperature is 1100?, pyrolysis time is 60min and the partial pressure of oxygen is 100%, the pyrolysis efficiency get above 95% at this conditions. The dynamic analysis of molten magnesium chloride pyrolysis reaction shows that, as a chemical reaction process control, the response of the apparent activation energy Ea=70.4 kJ/mol.IntroductionTitanium is a young metal, it is applied in industrial until the Second World War. It is 160 years from the discovery of titanium to the industrial production of ductility titanium by magnesium reduction method in the United States in 1948. As a new kind of metal, titanium and titanium material are better than the traditional metal materials in mechanical properties, heat resistance and thermal conductivity. Titanium is a kind of landmark structure and function material, which is called “space metal”, “Marine metal”, “Intelligent metal” [1-3]. Although the study of new methods of titanium melting get more at present, Kroll method and Hunter method are really applied to industrial production methods for titanium smelting, and Hunter method is already discontinued because of costs at present. The core technology in Kroll method of sponge titanium production process can be ome down to two circulation, namely the cycle of magnesium and chlorine in preparation-process of titanium sponge. In the traditional Kroll method, the cycle is realized through magnesium chloride which is produced by the electrolytic magnesium reduction process in hot molten state. But because investment of equipment for electrolysis method is too high, this method has not been used by most titanium sponge production enterprise in China. At present most titanium sponge production enterprise in China produce titanium sponge by the outsourcing of titanium tetrachloride, but the main disadvantage of this method is that the by-product of magnesium chloride is difficult to deal with."

Jan 1, 2012

By Xinghua He, Shujing Zhu

"Cycled fluidized bed ash (CFBA), a significant portion of fly ash produced from coal-fired power plants and rejected from the ash classifying process, has remained unused due to its high free CaO and S03 content. It is necessary to extend research on the method to reduce the expansion and improve the compressive strength by some effective chemical activator. This paper presents experimental results on the expansion by Le chaterlier tester and the compressive strength. Hydraulic ash-zeolite (HAZ) cementitious material was blended as the chemical activator to study the effects of the activator on the expansion and the compressive strength. The results show that HAZ can not only reduce the expansion, but also increase the prisms compressive strength. Scanning electron microscope observation and X-ray diffraction analysis indicate that the main hydrated products of the sample are calcium hydroxide, ettringite, zeolite and calcite, which can explain the results of the expansion and the strength tests.IntroductionNearly 80% of the electricity in China is produced by coal-fired plants, which results in the production of a large quantity of coal combustion residues, among which coal fly ash is the major component. Because of that the air-pollution becomes heavier as time going on. Cycle-fluidized-bed-combustion systems are retrofitted to meet air-emission standards mandated by China Clean Air Act. Cycle fluidized bed ash (CFBA) will present new challenges for coal-combustion byproduct management. The use of cycle-fluidized-bed ash as a cement replacement in concrete is the most attractive one because of its high volume utilization and widespread construction. However, the replacement of cement with cycle fluidized bed ash in Portland cement concrete usually increases the expansion and decreases the early strength of concrete. In many research of this field, most of them were focus on the activation of pozzolanic activity of CFBA and to make all kinds of blend cement. A number of studies had been carried out on the activation of CFBA using chemical activators. These studies involved using different activating methods including alkali activation and sulfate activation 11, 2]. The former involved the breaking down of the glass phases in an elevated alkaline environment to accelerate the reaction [3, 4]. The later is based on the ability of sulfates to react with aluminum oxide in the glass phase of CFBA to produce ettringite that contributes to the strength at early ages [5-7]. With respect to sulfate activation, the use of gypsum and sodium sulfate had been well studied [5-8]. HAZ is one of HAS sub-products which is a patentd chemical activator made by Wuhan University (ZL98113594.3). It had been used to activate CFBA to produce blend cement in many Chinese engineering projects and time has told us that it is a good activator."

Jan 1, 2012

By S. V. Ketov, V. P. Menushenkov, V. S. Shubakov

"The glass samples were obtained by melting of the oxides mixture SrO-Fe2O3-B2O3(Al2O3) at 1200-1250°C with subsequent quenching of the melt on quickly rotating steel roller. Submicronsized Sr(Fe,Al)12O19 particles were formed in glass-ceramic matrix during the crystallization aging of glass. The aging temperature Tag varied in the range 650-950°C. The submicron-sized hexaferrite powder was obtained by removing of the matrix phases using etching. The samples were characterized by X-ray diffraction, scamiing electron microscopy and magnetization measurements. The glass-ceramic material exhibits very high coercivity value up to 10 kOe. The samples of magnets were obtained by pressing of the hexaferrite powder at RT and subsequent aging in the range 900-1200°C. The aged samples exhibit coercivity value up to 8 kOe.IntroductionStrontium M-type hexaferrites have been widely used in technology and industry mainly for production of permanent magnets owing to their appropriate magnetic properties, chemical stability and low cost [1,2]. The SrFe12019-based compounds are characterized by high magnetocrystalline anisotropy and single easy magnetization axis. The highest coercivity is received for monodomain, defect-free single crystal particles with size D - 100 mn. Finely grained strontium hexaferrite prepared by chemical methods such as sol-gel pyrolysis and oxide glass crystallization exhibits high coercivity up to 6-8 kOe [3-5]. Owing to the partial substitution of Al for Fe in the strontium hexaferrite leading to the increase in the magnetic anisotropy field Ha=2Ki/M,, the increase in the coercivity may be received [6]. The notable results were achieved using the SrO-Fe2O3-AlzO3-B2O3 glass crystallization and formation of perfect submicron crystals of alumina-doped hexaferrite [ 6, 7]. The coercive force of glassceramics reached values of up to 10 kOe. Hexaferrite particles are well faceted and have the shape ofhexagonal bipyramids with truncated vertexes [7].In the present paper, we report results of our investigation into the SrO-Fe2O3-B2O3(Al2O3) glass crystallization, hexaferrite powders and permanent magnets, which were prepared by pressing submicron-sized hexaferrite powders at RT and subsequent sintering at 900-1200°C."

Jan 1, 2012

By Naiyang Ma

"High oil concentration is one of the major barriers for recycling of mill scale of steel hot rolling mills. It is of vital importance to find cost-effective technologies of reducing oil concentration in mill scale in order to recycle the mill scale without causing detrimental effects on production and environment. This paper discusses in-process separation of mill scale from oil at steel hot rolling mills. Formation of mill scale and status of oily wastewater at hot rolling mills are reviewed in the first place. A mathematical model is then formulated to relate oil concentration in mill scale to physical properties of mill scale, chemical and physical properties of wastewater and interacting parameters between mill scale particles and wastewater. From this model, three approaches of in-process separation of mill scale from oil are derived: (1) avoiding contacts between mill scale particles and oily wastewater, and (2) maintaining low oil concentration in wastewater, and (3) collecting mill scale in upper streams of wastewater flows. In-process separation of mill scale from oil might have advantages of lower capital cost, lower operating cost and less additional environmental concerns, compared to other strategies of separating mill scale from oil.IntroductionHot rolling is an inevitable step in producing finished steel products. Figure 1 schematically shows a steel hot rolling process. Semi-finished steel products, slabs here, are reheated first, and then the reheated slabs are discharged from the furnaces and transported on hot rolling trains to descaling units for removing scale with pressurized water. After being descaled, the slabs are rolled by roughing mills. After treated with cropping and the second descaling, the slabs are finally rolled into finished products, coils here, by finishing mills."

Jan 1, 2012

By Klaus Gamweger

"This paper introduces an innovative solution to open and close the tap hole of different furnace types in the copper industry with a slide gate system. Two plates with defined drilled holes are slid against each other, which enables effective starting and stopping of the copper flow as well as throttling. Typically, the copper is poured via a tap hole into a launder system by rotating the furnace into an appropriate position. Control of the casting rate is also performed in this manner. Or, in case of stationary furnaces the tap hole is opened by oxygen lancing and closed manually with a clay- or copper-cone. These procedures show a lot of disadvantages including splashing, oxygen pick-up, and energy losses as well as a severe danger for the working staff. All these problems can be overcome with an appropriate slide gate system.IntroductionThe control of the casting rate of a copper anode furnace usually is performed by rotating the furnace into an appropriate position. This implies that the taping starts with the tap hole at a very high position. Copper splashing and an uncontrolled oxygen pick up are - with several more disadvantages - the consequences. RHI AG has developed an innovative solution for copper applications to open and close the tap hole with a slide gate system which allows also an accurate control of the flow rate. By using this system it is possible to start the casting procedure with the tap hole at the deepest position, directly above the launder. This paper presents this new slide gate system in detail and shows the advantages in production and safety issues."

Jan 1, 2012

The global mining industry will always face significant challenges. Some, though, are bigger than others. What do you consider the major challenges facing the mining industry as a whole and SME in particular? Without a doubt, the major issue in both coal and metal/nonmetal mining industries is the ?graying? of the workforce in all aspects of mining. As the baby boomers continue to age, valuable experience is being lost by industry, government and academia. And there is the potential for SME to lose some of its membership. Now with that said, I should note that, despite the aging of the workforce, SME membership continued to grow by 7.1 percent during 2011.

Jan 1, 2012

Slurry flow, including flow through the charge, through the discharge grates, along the pulp lifters and its discharge from the mill is an important contributor to the efficiency of the grinding process within a SAG mill. Poor transport of finer ground material can adversely affect grinding leading to excess energy consumption and over-grinding of fine material. This paper extends a 1-way coupled DEM-SPH method to three dimensions and applies it to a 1.8 m diameter by 0.6 m long AG/SAG pilot mill. This provides detailed information on the internal flow of slurry within a SAG mill, including the prediction of dry regions and of slurry pooling. Full 3D analysis also allows the pulp flow patterns into and out of the mill via pulp lifter chamber to be investigated.

Jan 1, 2012

By F. J. Hrach, S. A. Gasiorowski, J. D. Bittner

"Separation Technologies, LLC (ST) has developed a processing system based on triboelectric charging and electrostatic separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. In contrast to the other available electrostatic separation processes that are typically limited to particles greater than 75 µm in size, the ST belt separator is ideally suited for separation of very fine (<1 µm) to moderately coarse (500 µm) materials with very high throughputs.. The technology has been also successfully applied to the beneficiation of a variety of minerals including calcium carbonates, talc, and potash. TECHNOLOGY OVERVIEWThe ST separator utilizes electrical charge differences between materials produced by surface contact or triboelectric charging. When two materials are in contact, material with a higher affinity for electrons gains electrons and thus charges negative, while material with lower electron affinity charges positive. This contact exchange of charge is universally observed for all materials, at times causing electrostatic nuisances that are a problem in some industries. Electron affinity is dependent on the chemical composition of the particle surface and will result in substantial differential charging of materials in a mixture of discrete particles of different composition.In the ST separator (Figures 1 and 2), material is fed into the thin gap 0.9 – 1.5 cm (0.35 -0.6 in.) between two parallel planar electrodes. The particles are triboelectrically charged by interparticle contact. For example, in the case of coal combustion fly ash, a mixture of carbon particles and mineral particles, the positively charged carbon and the negatively charged mineral are attracted to opposite electrodes. The particles are then swept up by a continuous moving open-mesh belt and conveyed in opposite directions. The belt moves the particles adjacent to each electrode toward opposite ends of the separator. The electric field need only move the particles a tiny fraction of a centimeter to move a particle from a left-moving to a right-moving stream. The counter current flow of the separating particles and continual triboelectric charging by carbon-mineral collisions provides for a multistage separation and results in excellent purity and recovery in a single-pass unit. The high belt speed also enables very high throughputs, up to 40 tonnes per hour on a single separator. By controlling various process parameters, such as belt speed, feed point, electrode gap and feed rate, the ST process produces low carbon fly ash at carbon contents of 2 % ± 0.5% from feed fly ashes ranging in carbon from 4% to over 30%."

Jan 1, 2012