Search Documents

By M. Rudolph, T. Leißner, TU Bergakademie Freiberg, C. Mämpel, R. Möckel, M. Embrechts, T. Leistner

Tin-mining activities have taken place in the region of the German Erzgebirge (Ore Mountains) for over hundreds of years up until 1991. For long times, gravity separation processes used to be the dominating beneficiation approach in those mining districts to recover cassiterite, the main tin-bearing mineral. For fine (< 100 µm) and very fine (< 20 µm) particles these approaches might not represent effective techniques, significant valuable materials could not be recovered and reported to tailings, where it was subsequently disposed. Thus, there are substantial amounts of cassiterite still present in these tailings disposals, most of it as very fine particles with already high degrees of liberation. That fact brings these tailings disposals into focus for potential reprocessing using beneficiation approaches, which are more sensitive to fine and very fine particles. In this paper we present results concerning the laboratory-scale treatment of material from exemplary heaps of the former Altenberg and Ehrenfriedersdorf mining sites using various flotation methods (including conventional froth flotation and oil-assisted flotation). Different size ranges of the material were previously prepared in order to investigate their response to the different techniques. For the study, special emphasis is put on agglomeration flotation, an oil-assisted flotation method. Therefore, an aliphatic oil phase of alkane basis is used to either selectively aggregate or collect the cassiterite particles. Recovery and flotation performance results are presented with respect to different process parameters: various collectors (including sulphosuccinamates and phosphonic acids) and depressants (including sodium fluorosilicate and oxalic acid) regime, oil dosage, agitation time and pulp density during oil/pulp agitation. Furthermore, the oil/particle aggregation behavior is analyzed via particle image analysis and, additionally, collector adsorption characteristics are investigated by contact angle measurements and zeta potential analysis. The data obtained is correlated with the testwork results achieved in order to interpret the flotation response of very fine cassiterite particles.

Jan 1, 2016

By L. Su, S. Liu, K. Jiang, K. Xie

The reduction of iron dissolution and acid consumption is fairly important in the extraction of Ni and Co from laterite ores from both economic and efficiency perspectives. BGRIMM conducted detailed research to investigate the behavior of iron in a nickel laterite leaching process. The mineralogy of Ni and Co was studied. In limonite ore about 76% of nickel is present in goethite while in saprolite ore 79% of nickel is associated with magnesium and silicon minerals. Test work revealed that limonite can be decomposed completely with enough acid concentration during atmospheric leaching. More than 98% of Ni and Co were leached into solution while 85% of the iron was also dissolved with 130-140 g/L iron in solution. Iron precipitates as hematite in the temperature range 250-270?C without neutralization reagents. That’s why limonite is treated by high pressure acid leaching (HPAL) technology to achieve nickel extraction and iron precipitation in the same autoclave. BGRIMM’s test results indicated that the remaining acid in atmospheric leaching solution and acid released by iron precipitation at a lower temperature was enough to leach saprolite efficiently. The so-called inverse leaching technology leaches limonite at atmospheric condition and the leaching slurry combined with saprolite is pumped into an autoclave to leach saprolite at 150-170?C. In the autoclave iron precipitates as hematite without acid consumption. Total nickel and cobalt extractions in the test program were more than 90% with iron content in solution below 8 g/L. In this inverse process iron dissolves in the atmospheric leaching stage and precipitates as hematite in the low temperature leaching stage. Compared with HPAL the leaching temperature is reduced to 150-170 ºC from 250-270 ºC. Compared to atmospheric tank leaching acid consumption is reduced from 850-950 kg/t ore (atmospheric) to 550-650 kg/t ore (inverse).

Jan 1, 2016

By K. Huang, L. Pan

"Darcy’s law has been used extensively to model cake filtration. It is a macroscopic model, in which particle size dominates the kinetics and cake moisture. In the present work, a capillary flow model has been developed from first principles to study the effects of microscopic parameters such as capillary radius, boundary layer slip, disjoining pressure, and surface tension that may be important for dewatering ultrafine particles. Laboratory-scale pressure filtration tests show that dewatering kinetics is strongly dependent on capillary radius, which in turn is influenced by surface hydrophobicity, surface charge, and length scales of particles. The model parameters determined from laboratory-scale filtration tests show that use of a hydrophobizing reagent can greatly improve fine particle filtration due to increased slip and decreased capillary pressure. The kinetics of dewatering kaolin clay is fastest at a pH where the layer-structured particles coagulate with a face-to-edge orientation. The capillary flow model developed in the present work may be useful for designing filters and optimizing operating conditions.INTRODUCTIONIn 2014, Canada produced 2.2 million barrels per day of crude oil from the oil sands resources in Alberta, which is expected to grow to 3.2–4.0 million barrels per day by 2030 (CAPP, 2013). One of the challenges to meeting these projections is the tailings management. At present, the industry uses ?77 km2 of the lands to construct tailings ponds. Significant amounts of the tailings disposed to the ponds are silts and clays that are slow to settle and consolidate, creating problems for reclamation. It is, therefore, the objective of the present work to develop a filtration model that may be useful for developing advanced dewatering technologies that can address the tailings management issues.Darcy’s equation is the governing law for filtration. It was derived as an empirical model by H. Darcy in 1856 while he was studying fluid flow in sand filters (Hall, 1956). Since then, many investigators derived it from first principles. It relates superficial fluid velocity to the pressure drop across a porous medium of known permeability. In filtration, the latter can be related empirically to particle size using the Kozney equation (Yoon, 2005)."

Jan 1, 2016

By A. Pytlik, W. Masny

"Underground mining is subject to various natural hazards such as seismic events, rockbursts, fire, and gas (methane). In general, an increase in the extraction depth causes an increase in the likelihood of these hazards, especially seismic activity and rockbursts. Dynamic phenomena such as rockbursts and tremors have been recorded on six continents: Europe (Poland, Russia, Czech Republic, Germany, and Slovenia), Asia (India, and China), North and South America (USA, Canada, and Chile), Africa (South Africa), and Australia. To select appropriate mine working supports for such dynamic phenomena, the performance characteristics of such support types must be determined under both static and dynamic load conditions.This article presents information regarding the application of rockbolts in Polish underground hard-coal mines. Dynamic phenomena occurring in the mines from 2004–2013 are also characterized. A methodology developed at the Central Mining Institute (GIG) for the laboratory testing of rockbolts is presented. In this methodology, the bolts are loaded by the direct impact of a free-moving mass (up to 20 000 kg) at speeds of up to 1.2 m/s. The facilities at GIG used to test the support under static and dynamic load conditions are characterized, and the results of laboratory tests on yielding bolts with a nominal capacity of 420 kN are presented. These types of bolts are commonly used for reinforcing steel arches and the surrounding rock mass in Polish coal mines. The results of the laboratory testing of yielding bolts are discussed.IntroductionSeismic events such as rock bumps and tremors occur with great frequency during underground mining. These phenomena have been reported in such countries as Poland, Czech Republic, Germany, France, Slovenia, Russia, India, China, the USA, Canada, Chile, South Africa, and Australia (Brauner, 1991; Potvin, Hudyma, and Jewell, 2000; Kidybin??ski, 2003; Driad-Lebeau et al., 2005; Li, Cai, and Cai, 2007; Whyatt and Loken, 2009; Durrheim and Riemer, 2012; Holub, Rušajova, and Holec?ko, 2011). Descriptions of the dynamic events and their effects in the form of damage to or destruction of supports have been presented in many publications, both for hardrock mines as well as for coal mines (Brauner, 1991; Dubin??ski and Konopko, 2000; Heal, 2010; Heal and Potvin, 2007; Simser, Joughin, and Ortlepp, 2002; Kaiser and Cai, 2012; Cai 2013; Nierobisz, 2013; Mark, 2014; Masny and Prusek, 2015). One of the main goals of the research has been to develop methods, criteria, and guidelines for the selection of an optimal and safe support for mine workings located in areas of rock bumps or tremors. Example of such studies include the Canadian Rockburst Support Handbook (Kaiser, McCreath, and Tannant, 1996), or the principles presented in the literature (Li, 2010; Cai, 2013)."

Jan 1, 2016

By Matteo Cortinovis, Giuseppe Gelmi

"INTRODUCTIONEdilmac dei F.lli Maccabelli (hereinafter referred to as Edilmac) has recently developed a special civil engineering application using the Raise Boring technology with the assistance of Inrock MGS (Magnetic Guidance System). Applying the Paratrack Magnetic Guidance System coupled with a directional mud motor to the drill string allows a better accuracy compared to standard drilling, as showed in our tests. This is the first time the Paratrack System has been applied to the Raise Boring technology. RAISE BORING METHOD STATEMENT The Raise Boring technology was born in North America during the Sixties. In 1962, Ingersoll and Robbins were the first companies to produce Raise Boring Machines (RBM). The technology was first used in the underground mine industry, in order to bore ventilation shafts and passes through different levels, thus reducing the cost of haulage. The Raise Boring method is only feasible in stable rock conditions. The Raise Boring method consists of drilling a small diameter pilot hole that reaches a tunnel located at the bottom of the drilled hole. Once the pilot hole reaches the tunnel, a reamer head is installed at the end of the drill string and pulled up, creating the hole with the designed diameter (Figures 1 and 2). The main equipment, which is required to perform Raise Boring activities, is the following: •,An RBM; •,A tricone bit; •,Drilling rods; •,A reaming head; The standard mucking of the pilot hole is done with water or bentonite mud. For the last 30 years, Edilmac has developed a mucking process, which uses compressed air with the addition of foam or a small amount of water for dust control.Pilot hole tricone. The drilling of the pilot hole is usually performed with a tricone bit having a diameter between 11” (27.61 cm) and 15” (38.10 cm) (Figure 3). High strength rods. They generally have a diameter ranging from 10” (25.40 cm) to 12 ?” (32.70 cm) (Figure 4), depending on the length and the final diameter of the shaft."

Jan 1, 2016

By Brian Gettinger, Jim Schlaman, Alston Noronha

"INTRODUCTION The public understanding of green solutions today is based on the definition of sustainability adopted by the Brundtland Commission (World Commission on Environment and Development) in 1987: “development that meets the needs of the present without compromising the ability of future generations to meet their own needs.” Over time this initial definition evolved to identify three distinct factors impacting sustainability that are often referred to as the “Triple Bottom Line”: Economic, Environmental and Social. The triple bottom line approach seeks to drive outcomes that create maximum value for all stakeholders. In the last ten years purveyors of water and wastewater tunnel solutions have found themselves on the wrong side of a politically polarizing issue in the crosshairs of politicians, environmental activists and community groups branding tunnels as expensive, “gray” and not-sustainable. Tunnels under design were stopped and large planned tunnel programs were delayed or canceled. Therefore being sustainable and “green” is not simply using natural vegetation, but creating an asset that meets current and future needs and will not become a future liability. As this paper will discuss, tunnel projects embody a sustainable triple bottom line project well, are equally sustainable as green infrastructure, and have begun to gain awareness for their sustainability. GREEN INFRASTRUCTURE CHANGES TUNNELING LANDSCAPE The green movement quickly swept across the nation in the mid to late 2000’s and was a hot topic in the media and at all the local, regional and national industry conferences. Politicians espoused the benefit of green infrastructure including job creation, urban renewal, aesthetics, property values economics and sustainability. The political microscope was focused the closest on stormwater and wastewater management, particularly in communities responding to combined sewer overflow (CSO) consent decrees from the Environmental Protection Agency (EPA). As communities with CSO problems evaluated their long term control program (LTCP), local government officials and planners began to balk at the huge price tag required for compliance and began looking for alternatives. “Green” infrastructure was proposed as lower cost solution that could be used to offset capital-intensive “gray” infrastructure like new sewers, storage tanks, tunnels, and treatment facilities. In addition, including green infrastructure in a previously negotiated LTCP required a reset on the entire planning process, additional studies and more planning which would push capital investment further off into the future, subsequently delaying unpopular user rate increases. As a result, tunnel projects as well as trenched conveyance and treatment plant projects that had not yet started construction were stopped, delayed or substantially changed."

Jan 1, 2016

By S. V. Ulianov, A. Y. Senchenko, E. M. Kurchevskaya

"A process sample of old copper-containing tailings (-2.0+0 mm) from an iron-ore plant was tested in TOMS institute in order to develop a process for copper concentrate production. The study of tailings material composition indicated that -0.2+0 mm fraction was efficient and contained 97.26% of copper. Copper is predominantly concentrated in chalcopyrite which is present both in free form and in intergrowth with ore and rock-forming minerals. Study of chalcopyrite using an optical microscope and Qemscan SEM determined that the most grains surface was covered with oxide films. Additionally, a lot of grains had micropores on their surfaces that indicated a partial mineral leaching. The oxide films did not make it possible to float copper minerals from head material. It was recommended to apply an attrition operation to restore chalcopyrite floatability. In order to increase selectivity a regrinding stage for a primary copper concentrate was introduced to obtain P80 26 um. Taking these recommendations into account a flotation flowsheet was developed to process the old Cu-containing tailings. The flowsheet allowed us to obtain a concentrate with 23.5% Cu content at 71.5% recovery.INTRODUCTIONStudy of material composition is an important prerequisite for development of a minerals processing technology. Mineralogical study contributes to search for an efficient technology to recover valuables and for prospective methods of minerals processing.The use of such up-to-date analysis methods and equipment as Qemscan and Mineral-C7 allows one to determine minerals size, liberation degree, and mineral associations. Mineralogical data can reveal reasons for hard processing of minerals prior to development of the process.The advanced process mineralogical methods used to study Cu-bearing pond tailings indicated several factors that influenced development of the process. The first one is a barren size fraction which is to be removed from the process in order to considerably reduce the costs connected with grinding. The second is the presence of films on chalcopyrite surface; in this context, a preliminary attrition of the material was recommended. The third factor is finely disseminated Cu minerals in sulphide and in the rock, which predetermined selection of particle size for flotation. All these data led to significant decrease in time required to develop the process technology. The developed process flowsheet based on the obtained mineralogical data is present in Figure 1."

Jan 1, 2016

By H. Staton, XPS Consulting & Testwork Services, T. Deng, M. Kelvin

"Lundin Mining’s Eagle Operation, located in Marquette County, northern Michigan consists of a mine and concentrator that processes a Ni-Cu-(PGE) ore. Mine production began in 2014 and is expected to achieve production of approximately 23,000 tonnes of Ni and 20,000 tonnes of Cu per year. The ore is trucked to the Humboldt Mill, where both a Ni and Cu concentrate is produced.XPS Consulting & Testwork Services (XPS) has assisted the team at Eagle since 2013. Prior to start up, the ore was piloted at the XPS lab in Sudbury, Ontario to demonstrate the concentrator flowsheet and establish flotation operating strategy. XPS consulting metallurgists worked closely with the Eagle team during the commissioning of the plant providing troubleshooting, sampling, metal balancing expertise and support. Finally, a series of monthly composites over a 6 month period was submitted for mineralogical characterization to assess plant performance, identify opportunities for improvement and to provide a baseline for the future operation.Lundin’s investment to test the ores ahead of mining and to team with XPS’s experienced mineral processing engineers to help commission the plant has led to the plant achieving concentrator production targets shortly after startup. The commitment to training and implementation of best practices, and a culture where ongoing testing is the norm, puts the Eagle Operation on sound footing for future operation.INTRODUCTIONLundin’s Eagle Mine is a subsidiary of Lundin Mining located in the upper peninsula of Michigan. The mine itself is an underground operation and the ore is trucked from the Eagle mine site 2 hours to the Humboldt mill.The ore is an ultramafic hosted high grade Cu Ni deposit and exists as either massive or semi massive sulphides. The high resource grade of Cu (2.49%) and Ni (2.93%) make this a valuable ore source. (Owen & Meyer, 2013) A metallurgical team was put together by Lundin to ensure the mill was designed and commissioned to optimize metallurgy in the shortest time from this valuable deposit. The commissioning plan targeted commercial production by Q1 2015."

Jan 1, 2016

By C. Heckman, M. S. Moats, A. Luyima, W. Cui

"Cyclic voltammetry, electrochemical impedance spectroscopy (EIS), and galvanodynamic and chronopotentiometric techniques were used to characterize the effects of DXG-F7®, a commercial smoothing agent, on copper electrodeposition onto 316L stainless steel from a synthetic electrolyte containing 40 g/L copper (Cu2+), 160 g/L sulfuric acid (H2SO4) and 20 mg/L chloride (Cl-) at 40oC. The findings were compared against results using HydroStar® 4208, a modified polysaccharide. The nucleation overpotential and plating potential observed in cyclic voltammetry and galvanodynamic testing showed that neither DXG-F7 nor HydroStar significantly polarized acidic copper electrodeposition. Subtle differences between the additives were found during EIS testing and modeling, but more research will be needed to fully understand these differences. Surface-roughness measurements of two-hour deposits indicate that DXG-F7 and HydroStar produced smoother deposits as their concentrations in the electrolyte increased. No difference in the surface roughness of deposits was detected between the additives. Based on the experimental evidence resulting from the laboratory testing, no significant difference was found between DXG-F7 and HydroStar at 20 mg/L Cl- concentration, with the exception that DXG-F7 dissolves more easily in water than HydroStar. Introduction Cathode deposits obtained from acidified copper sulfate electrolyte(s) without organic additives are often soft, coarsely crystalline and nodular (Sun and O’Keefe, 1992). Therefore, small amounts of organic additives are added to the electrolyte to produce level and dense cathodes during copper electrowinning. The action of organic additives is thought to be due to their adsorption on the surfaces of the newly formed copper grains. Hence, any copper grain that grows excessively fast adsorbs a layer of organic additive, which inhibits growth. The result is a smoother and harder deposit of suitable purity (Sun and O’Keefe, 1992). In part I of our four-part series on the examining of copper electrowinning smoothing agents, a review of previously published work on organic additives used during copper electrowinning was presented (Moats, Luyima and Cui, 2016). In the review, it was noted that many tankhouses had switched from guar to other saccharide-based products such as HydroStar and DXG-F7."

Jan 1, 2016

By J. -F. Blais, M. -O. Simonnot, P. Charbonnier, J. Mocellin, Université de Lorraine INRA, G. Mercier

"Huge amounts of air pollution scrubber sludge have been generated during ferromanganese production using blast furnace. These residues have been historically deposited in ponds near steel making plants. They are very rich in zinc, manganese and lead (5 to 40 %) and also contain aluminum and iron. Considering the market value of these metals, brownfield sites can now be used as secondary resources. These ponds also have to be cleaned up to meet the environmental regulations.We have developed a hydrometallurgical process to recover Zn, Mn and Pb in order to produce valuable compounds of Mn and Zn and recover the final Pb residue by pyrometallurgy. The Zn and Mn compounds need to be pure enough to be economically valuable. Batch laboratory tests were carried out to determine suitable selective leaching conditions. The investigated operating conditions were acid concentration, pulp density and temperature. Optimal conditions to maximize zinc extraction (100 %) and manganese extraction (95.9 %) were found using sulfuric acid and sodium metabisulfide. The final residue contained 14.8 to 23.8 % of Pb. Then, Zn was recovered in the form of ZnO or ZnS by precipitation and Zn metal by electrowinning, while Mn was recovered as MnCO3 with a fairly acceptable concentration of impurities.INTRODUCTIONFerromanganese has been produced by pyrometallurgy in much of Western Europe for centuries. Use of wet scrubber to remove pollutant and dust particles from gas stream was common for most of these operations. Those residues contain high concentration of Zn, Mn and Pb. They have been left to decant in settling ponds installed close to the steel production plants. They now constitute heavily contaminated artificial soils. Those sludges are so contaminated with Zn, Mn and Pb that they can be used for metal production. Currently, no method is available to decontaminate these residues and recover Zn, Mn and Pb. Therefore, an approach considering these brownfield sites as secondary resource is in development. Doing so would achieve two goals, decontaminate the site and produce metals.. (Huot, Faure, Biache, Lorgeoux, Simonnot, & Morel, 2014a; Huot, Simonnot, Marion, Yvon, De Donato, & Morel, 2012; Huot, Simonnot, Watteau, Marion, Yvon, De Donato, & Morel, 2014b)."

Jan 1, 2016

"1.0 INTRODUCTIONThese Guidelines reflect the state-of-the-practice of the Deep Mixing Method (DMM) in North America. DMM is an in situ mixing process that breaks down the soil structure; injects binders, fillers and reagents into the soil; and blends them with the soil. DMM is also commonly referred to as Soil Mixing. The final properties of the treated soil in situ are a function of the composition of the native soils and groundwater, the binders introduced, the mixing methods and energy, and the conditions and time of curing. Treated soils generally have increased strength and stiffness and/or reduced permeability relative to the native soils.This document addresses DMM performed by rotating single and multiple axis mixing tools, rotating cutter wheels at the end of a rigid kelly bar, or trench mixing using a rotating cutting/mixing chain around the perimeter of a rigid bar. Binder may be injected through low or high energy (velocity) jets.The treated soils created through wet DMM are heterogeneous mixtures of binder, water, soil, and groundwater. Treated soils produced by dry DMM techniques are a mixture of binder, soil, and the water already present in the native soil.DMM applications described in this document include•,Earth retention•,Liquefaction mitigation•,Groundwater seepage control and containment isolation•,Bearing capacity improvement•,Deep foundations•,Mass stabilization and contamination containment•,Embankment, levee and dam strengthening, and stabilization•,Casing replacementThis document was developed to address deep foundations applications. Use of deep mixing for seepage control is not specifically addressed. The reader is referred to documents prepared by the U.S. Army Corps of Engineers for additional information. Shallow soil mixing and the use of DMM for stabilization/solidification of contaminated soils performed at depths less than 10 feet (3 m) are mentioned briefly. Jet grouting is not covered by these guidelines."

Jan 1, 2016

"The Detour Lake Mine is located in northeastern, Ontario, approximately 300 kilometres northest of Timmins and 185 kilometres by road northeast of Cochrane. The mill processes a free milling gold ore using both gravity circuit and leaching with a state-of-the-art carbon-in-pulp circuit. The grinding circuit is a conventional SABC circuit with a tonnage of 55,000 mtpd at 95 microns with the addition of pre-crushing upstream of the SAG mill.The present paper will describe the methodology used to successfully prove that gold of the Detour Lake Mine ore is mostly concentrated into the fine size fraction of the blasted rocks. It will describe the various options possible to create value from this ore property.IntroductionThe purpose of this test work was to determine the grade of the pebbles and consider if there was value into discarding the pebbles and replacing the material by fresh feed.1. Pebble samplingThe pebbles were sampled and assayed for grade every day for 3 months. After 3 months of sampling, the results showed that the pebbles only carried 28% of the fresh feed grade. This phenomenon can possibly be explained by the fact the gold is located into area of fracture in the rocks.January-March 2014 – Pebble assay average• Line #1 = 0.222 g. Au/t• Line#2 = 0.275 g. Au/t• Head grade = 0.88 g. Au/t2. Crushing and grinding circuit surveysWith the above information, a grinding circuit survey was planned. The purpose of the survey was to build a JKSIMMET model of the grinding circuit for mill optimization but also to understand the deportment of gold into various size fractions that may explain why there is so little gold in the pebbles. All streams and size fractions was analysed for particle size analysis and for gold.Since Detour has dual grinding lines, both circuits were sample at the end of May. Two supplemental survey of the secondary crushers were also done and a survey of the gyratory crusher."

Jan 1, 2016

By L. D. Roper

"This paper introduces novel comminution flowsheet concepts involving a novel apparatus, eccentric-high-pressure-centrifugal-comminution (eHPCC), and forthcoming advantages to the international mineral processing community. eHPCC is one-machine synergising high-pressure-rolling surfaces, high-intensity-attrition and centrifugal classification. eHPCC has demonstrated: an absorbed power- intensity of 4 MW/m3; receipt of lump feed whilst producing 80% of product particles less than (p80) 120 µm (choke-fed, dry, open circuit without grinding media; an inert comminution environment); tramp metal tolerance, and a minimum embodied-free-energy saving of 15% as compared against conventional comminution (this comparison withstanding 133-times difference in throughput). Furthermore, this paper introduces: process design and operating characteristics of eHPCC (wet, dry, with and without grinding media); reline considerations (vertical-lift without confined-space). The international mineral processing community is invited to consider eHPCC as an alternative to conventional comminution circuits and/ or complimentary so as to enhance existing process flow sheets.INTRODUCTIONEccentric-high-pressure-centrifugal-comminution (eHPCC) was conceived in 2013 (Patents pending) and has the potential to eliminate the in-efficiencies and complexity of conventional tumbling mill circuits. During the development and testing phase eHPCC demonstrated improved energy efficiency and sustainability offsets.eHPCC will compliment any upstream feed source, be it run-of-mine (ROM), primary crushed rock, or any other conventional comminution stream such as tumbling mill oversize. Another novelemerging technology, Conjugate Anvil-Hammer Mill (CAHM) (Nordell and Potapov, 2011), receiving ROM, will be a complimentary open-circuit feed to eHPCC for very high throughput flow-sheets.eHPCC may compliment downstream process requirements through selective mineral liberation. Selective mineral liberation is entirely feasible as the ore is comminuted upon itself (autogenously) in the high pressure zone caused by the synchronous rotating components."

Jan 1, 2016

By E. L. Chanturiya

The research and characterisation for compositional, physicochemical, structural, electrical and flotation properties of various pyrite samples for a copper-zinc sulfide ore was carried out. Various methods were used during the research, such as optical microscopy, X-ray diffraction, electron probe micro-analysis (EPMA), phase emission analysis, routine chemical analysis, auger electron spectroscopy (AES), scanning electron microscopy (SEM), back-scattered electron images (BSE), potentiometry, and instrumental neutron-activation analysis, flotation. Analysis of obtained results established the interrelation between impurity structures and concentration of electric charge carriers in minerals, Butyl xanthate sorption and flotation yield of pyrite. The research concluded that pyrite samples differ by morphology, micro defects of structure, concentration of donor and acceptor impurities (Co, As, Sb, etc.) and conductivity parameters (thermo-electrical force, specific resistance and concentration of charge carriers The peculiarity of pentagon-dodecahedral pyrite is the high concentration of electric charge carriers (electrons) and the more negative surface potential (by 25–75 mV) in comparison to cubic pyrite. The surface of cubic varieties is more active, therefore it is oxidized in alkaline lime medium much faster, than the surface of pentagon-dodecahedral varieties. This phenomenon is caused by high reaction ability, irregular jointing and defects of cubic pyrite. This promotes the increase of calcium ion sorption on its surface and the decrease of Butyl xanthate sorption. According to this, an increase in alkalinity (lime medium) from a pH of 10.0–11.5 leads to an increase of gold content reporting to the tail of bulk flotation. Gold content is increased from 0.58 g/t (?? 9.5) to 1.9 g/t (?? 11.6), which represents an increase in gold recovery of 24.68 to 79%, respectively.

Jan 1, 2016

By W. Jomaa, V. Songmene, O. Mechri, Laval Université, P. Bocher, J. Levesque

"A 2D finite element modelling (FEM), based on pure Lagrangian approach, is developed for studying the serrated chip formation during high speed machining (HSM) of 7075-T651 alloy. The solution was achieved using a commercial software package, ABAQUS/Explicit v6.13. The Johnson-Cooke (JC) constitutive equation is used to describe the work material behaviour. Moreover, the JC damage equation is implemented into the FEM to take into account for the shear localization during the serrated chip formation. Modified Coulomb friction model has been used to characterize the sliding/sticking effects on the tool-chip interface with the friction coefficient and shear flow stress determined by force calibration and machining data, respectively. The proposed FEM is validated using experimental data obtained in HSM of 7075-T651. The FEM was able to predict accurately serrated chip morphology. The intensity of chip segmentation was found to increase with cutting speed.INTRODUCTIONHigh speed machining (HSM) is one of the most used processes for manufacturing aircraft parts with aluminum alloys. For aluminum alloys, the use of HSM increases metal removal rate and reduces the formation of built up edges and burrs. However, it was found that serrated (also named segmented or sawtooth chip) and discontinuous chips can be produced during HSM of some high strength aluminum alloys, such as 7075-T6 alloy (Rao & Shin, 2001). Many parameters were found to affect the segmented/discontinuous chip formation during the machining of aluminum alloys.There are two cases in which the serrated chip can forms: the first is when machining hardened materials (Morehead, Huang, & Luo, 2007), and the second, when machining ductile materials with a cutting speed higher than a critical value (Barry & Byrne, 2002). Different theories and models were developed in order to explain the formation mechanism of such kind of chips. According to Astakhov (2006), the segmented chip formation is attributed to variations in stress and plastic deformation states, and resulting temperatures on the cutting zone. Liyao et al. (2013) stated that the segmented chip formation was mainly attributable to adiabatic shear instability/catastrophic strain localization. Others (Vyas & Shaw, 1999) suggest that the fracture/crack propagation mechanism is at the root of chip generation."

Jan 1, 2016

By Xiqing Wu, Liang Dai, Tao Yue, Longsheng Yi, Ruifang Wang

Magnetic seeding flotation (MSF), i.e. adding magnetic seeds and pre-magnetization-flotation, is a new flotation technology especially for fine particles, which improves the flotation performance by enlarging the apparent size of the particles in a way of magnetic agglomeration. Both the fine coal slimes with a size of 66.68% –38µm and the pyrite slimes with a size of 73.95% –23 µm were investigated by the MSF, respectively. Flotation tests with variable of dosages of magnetic seeds and polyacrylamide were conducted, and some measurements, such as laser diffraction size analysis, magnetic susceptibility by vibrating sample magnetometer (VSM) and infrared spectroscopy (IRS), were also applied in order to probe the mechanism of the MSF. Based on the tests, measurements and calculations it was found that both the recovery of coal and the flotation kinetics of pyrite slimes increased with the additions of the magnetic seeds, and in the presence of polyacrylamide the coal flotation was further strengthened due to a synergetic effect of magnetic seeds and polyacrylamide on the flotation and a relatively larger apparent size of slimes after additions of magnetic seeds and polyacrylamide. The reason for the MSF lies in fact that the presence of the polyacrylamide intensified the adsorption of magnetic seeds on the coal particles and increased the coverage of the magnetic seeds on the coal surface from 0.2 to 1.3 wt%, resulting in increased magnetic susceptibility of coal particles from 9.13×10-9 to 22.17×10-9 m3/kg and thus a low magnetic field strength of pre-magnetization needed for the magnetic agglomeration among the coal particles from 602 to 24 mT prior to proper flotation. IRS shows that polyacrylamide chemisorbed on the surfaces of both coal particles and magnetic seeds, thus acting as the bridging media between particles and seeds.

Jan 1, 2016

By G. O. Oniyide, H. Yilmaz

The South African platinum mines in the Bushveld Complex (BC) have unique features that distinguish them from the gold mines. They have a higher horizontal stress closer to the surface, lower occurrence of seismic activity (caused mainly by pillar failure), and are sited in an area of high geothermal gradient. One of the future challenges of platinum mining is the increasing temperatures as the mining depth increases. High temperatures invariably bring about higher ventilation costs and require different approaches to human factors and ergonomics. Excavation stability would also be another area of concern due to increasing stresses. In this investigation, the effect of temperature on the physical and chemical properties of selected Bushveld rocks (chromitite, pyroxenite, norite, leuconorite, gabbronorite, mottled anorthosite, varitextured anorthosite, granite, and granofels) was studied by means of optical microscopy and scanning electron microscopy using energy-dispersive Xray spectrometry (SEM-EDX). The rock specimens were heated in a temperature-controlled oven a rate of 2°C /min to 50°C, 100°C, and 140°C and kept at temperature for five consecutive days. Samples were allowed to cool to ambient temperature (approximately 20°C) before image capturing. Micrographs of the specimens were taken before and after heat treatment. All the SEM samples were also subjected to heating and cooling on alternate days for ten days in order to observe the effect of repeated heating and cooling on the rocks. The results of the optical microscopy analyses showed minor physical changes in the rocks. The SEM images revealed that cracks initiating at lower temperatures extend with increasing temperature. The chemical analyses showed that the temperature range considered in this research is not high enough to induce changes in the chemical composition of rock samples.

Jan 1, 2016

By G. C. Lindeque

"A downward trend in tyre life on haul trucks at an open pit iron ore mine prompted an investigation into the current tyre management strategy in order to improve tyre life. ‘Best practice’ was compared to the current tyre management strategy at the mine to determine aspects that could be improved. Aspects that showed significant room for improvement included employee tyre awareness, tyre pressure maintenance, and road conditions. For each of these aspects a plausible alternative was suggested.A new tyre management strategy was formulated as a step-by-step guide on how to implement the proposed changes. Each step introduces new initiatives but at the same time builds on the previous step’s success. A sensitivity analyses was performed to determine the impact of the proposed changes, with the variables being the reduction in the percentage of premature tyre failure, and the reduction of the site wear rate.The ‘most likely’ scenario showed an increase in tyre life of 41% for the Komatsu 730 trucks and 105% for the CAT 777 trucks if the entire tyre management model is implemented. This would result in a possible annual saving related to tyre usage of R9.2 million. OverviewThe study focused on the tyre life on the main haul fleet at an open pit iron ore mine. The haul fleet consisted of 17 Komatsu 730 (180 t) haul trucks and 12 CAT 777 (90 t) haul trucks.The haulage operation consists entirely of tyre-based haul trucks. Five per cent of the total mining budget is related to tyre costs. Since 2012 there has been a steady decrease in tyre life as measured in operating hours (Figure 1) due to the high percentage of tyres that fail prematurely. In 2014 a total of 41% of all tyres failed prematurely and 61% were classified as ‘worn out’."

Jan 1, 2016

By L. V. Kin, V. V. Lodeischikov, A. V. Byvaltsev, IRGIREDMET JSC, O. D. Khmelnitskaya, S. V. Petrov

"Irgiredmet Institute carried out the study on the development of gold recovery technology from refractory ore from a Russian deposit. The ore contained 1.1 g/t Au, 1.5% of pyrite and 2.4% of pyrrhotite. The recovery of gold achieved was 84.7% using gravity with generation of high grade recoverable gold concentrate and gravity middling. In the course of lime treatment, cyanidation of the middling followed by tailings detoxification the consumption of reagents was 13.0 kg/t CaO, 95 kg/t NaCN and 72 kg/t Ca(OCl)2 of the concentrate. This was capital intensive.In order to decrease the consumption of reagents, magnetic separation of the middling of the concentrates from gravity separation was added to this flow sheet. Pyrrotite recovered to magnetic fraction, which did not contain gold in accordance to this advanced flow sheet. The mass yield of pyrite goldbearing non-magnetic fraction decreased down to 1.5 times in relative to gravity middling. The slurry filtration prior to and after cyanidation allowed the organization of cyanide solution recycling.The results of pilot plant tests using the developed flow sheet showed that the content of pyrrhotite in the non-magnetic fraction decreased from 59.1% to 11.3%. The reagents consumption was 12 kg/t CaO, 3 kg/t NaCN and 16 kg/t Ca(OCl)2 of the pyrite concentrate. The total gold recovery using this flow sheet was 83.4%. Due to a decreased consumption of reagents, cost efficiency of the process was achieved. Based on the results of this research, a project design criteria was developed. A processing plant with the annual throughput of 2.6 million tonnes of ore is being designed."

Jan 1, 2016

By M. R. MacIver, M. P. Pawlik

"An image analysis method based on chord length distributions is applied to the batch settling of polyacrylamide flocculated kaolin suspensions. Two features of the interaggregate void space, the void chord length distribution mean and the white-to-black distribution ratio are extracted from an image series obtained over the two hour settling experiments. This approach produces three signal values, from two different probability distributions that can be measured as an indication of underlying sediment bed density and aggregation state. Further work is required on the physical interpretation of the signal, the image acquisition conditions, and the parameter selection methods. It is suggested that this chord length based feature extraction technique may be a useful signal to monitor during batch settling or thickening.INTRODUCTIONFew in situ techniques are available that can be used to directly measure aggregate properties within sediment beds in thickeners or secondary settlers. Typical process variables monitored include rake torque and height, bed level and pressure, feed rate and density, underflow rate and density, settling rate, and overflow turbidity; yet these process variables are only weakly related to process dynamics (Concha et al. 2014). Additional process monitoring signals, based on the direct measurement of aggregate properties could improve solid-liquid separation control and allow the extraction of more detailed information from batch settling experiments.Several optical methods exist for measurement of moving suspensions of aggregated solids in the dilute concentration regime, such as focused beam reflectance measurement (Peng and Williams 1994), and the turbidity fluctuation method (Gregory 1985). In the more concentrated region of a thickener, acoustic backscatter penetration and attenuation measured with an acoustic probe and changes in the underlying solid concentration in the highly concentrated, near-bed region of a thickener as a function of height and time (Hunter et al. 2012). While machine vision for froth monitoring has been thoroughly studied with at least five commercialized technologies (Aldrich et al. 2010), its’ application to the study of thickening has been limited."

Jan 1, 2016