Search Documents

By O S. Maluleke

In some deposits valuable heavy mineral quality is poor due to increased mineral surface coatings from higher slimes and more competent sand orebodies. Mineral surface coating can include silica or aluminium rich clay minerals and iron based minerals that render the final product quality off-specification, in this case specifically ilmenite and zircon. Conventional physical beneficiation processes such as magnetic separation, electrostatic separation and gravity separation are not able to remove these surface coatings. Surface dependent separation techniques such as electrostatic separators are affected by these coatings which hinders the rejection of non-valuable mineral from product. Attrition scrubbing is the most commonly used technique to reduce surface coatings, using mechanically induced particle to particle interaction, abrasion and shearing.In many cases it is a challenge to measure the surface removal efficiency of these scrubbing units. Elemental analysis techniques (ie X-ray flourescence) (XRF) in a multi mineral environment are unable to measure surface impurity reduction with enough precision. Mineralogical analysis (in this case Qemscan®) has constraints in terms of sample preparation with highly coated particles being plucked out during block polishing. This paper suggests a combination of laboratory separation techniques coupled with elemental analysis to evaluate the surface removal efficiency. Three different types of feed materials were used to analyse the efficiency of surface removal using production attritioner scrubbers. This approach relates the downstream beneficiation plant’s expected performance with that of the attrition scrubber’s scrubbing efficiency.

Oct 5, 2011

By Alfred H. Brand

New York City contains extensive deep deposits of glacial lake varved silt and clay, often overlain by organic soil. An 18 story building was proposed for Manhattan's upper East Side in one such area where bedrock is approximately 200 ft deep. Various pile and caisson alternatives were considered extending through the glacial lake soil to rock, but all proved beyond the project budget. Laboratory testing showed that the glacial lake deposits were preconsolidated. A test pile program using auger cast piles bearing in the glacial lake deposits proved that such piles could safely carry a load of 60 tons per unit. The auger cast pile scheme was estimated to be more economical than a deep pile alternative. A further benefit was that the vibration-free pile installation procedure posed less risk to adjacent structures which had been founded at shallow depth in fill above organic deposits and were stressed and cracked due to prior settlement. The project was designed with the anticipation that the glacial soils beneath the tips of the piles would produce a building settlement of 1 to 2 inches. The building was constructed in 2001 and 2002. It has been completed and is now occupied. Settlement data show that the building is performing as predicted. The auger cast pile scheme founded in a compressible stratum has proven to be successful and is a very unusual foundation alternative.

Jan 1, 2003

"Guideline Augered Cast-In-Place (ACIP) Pile Specification and Commentary11.0 GENERAL1.1 SCOPEThe Pile Contractor shall furnish all labor, materials, tools and equipment necessary for furnishing, installing and testing Augered Cast-in-Place (ACIP) piles as shown on the Contract Drawings and as specified herein.ACIP piles are commonly referred to by several other names. Some of them are trademarks or service marks owned by Foundation Contractors and some are names that try to describe the installation process. The term “cast-inplace” is sometimes replaced with “cast-in-situ,” especially in Europe. Some common names are Auger Cast Piles, Intruded Mortar Piles, Augerpress Piles, Augered Pressure Grouted Piles, AugerPile Foundations, Continuous Flight Auger (CFA) Piles, Grouted Bored Piles, Augered Grout-Injected Piles, Drilled or Augered Uncased Piles, and Uncased Cast-in-Place Concrete Piles. To avoid confusion, ACIP pile will be used exclusively herein.1.2 PILE CONTRACTOR QUALIFICATIONSThe ACIP piles shall be installed by an experienced Pile Contractor who upon request of the Engineer shall submit evidence of successful ACIP pile installation under similar job and subsurface conditions, including a job supervisor who shall have a minimum of five years of method specific experience.The proper installation of the ACIP piles is dependent upon the procedures used by the Pile Contractor’s field representatives and equipment provided. The Pile Contractor’s personnel responsible for the installation should have relevant experience with the auguring and pumping equipment, experience placing piles under similar site conditions (including restricted headroom if appropriate), in similar subsurface conditions, as well as experience handling the special grout mixes, admixtures, etc."

Jan 1, 2016

The development of Augered Cast-In-Place (ACIP) piles started in the late 1940's when several projects were performed by Intrusion-Prepakt, Inc. utilizing various techniques to place the piling. On some projects, a grout pipe was placed down the augered hole after the auger was withdrawn, and structural grout was pumped into the hole until grout appeared at the surface, after which the grout pipe was withdrawn. In some instances coarse aggregate was placed after a grout pipe was in place, and then the grout was intruded into the coarse aggregate, making a pile using the preplaced concrete method. Another method of forming augered piles used a system of driving or drilling a grout pipe through soils adjacent to the auger once the auger was drilled to the bottom elevation. The tip of the grout pipe was placed in close proximity to the tip of the auger. As the auger was withdrawn, grout was pumped through the grout pipe filling the augered hole from the bottom. After grout was observed at the surface, the grout pipe was withdrawn. In 1951, a patent was applied for by Raymond Patterson describing the above techniques along with a technique for placement of grout using a hollow stem auger and a removable plug or lead bit at the tip of the auger. The expendable plug or lead bit was removed by using grout pressure. The patent was granted in 1956. Around this same time other augered piling con-tractors began operations under licensed arrangements.

Jan 1, 2003

Jan 1, 1997

By BRETTMANN TRACY

Jan 1, 2000

Jan 1, 1998

Jan 1, 2001

Jan 1, 2002

Jan 1, 2004

Jan 1, 2003

By Amy McBrayer, Vladislav Kecojevic, Juan David Valencia Quiceno, Dragan Bogunovic

The mining industry’s commitment to innovation reflects a history of adopting technological advancements to enhance workplace safety, environmental sustainability and vocational training. The objective of this research was to develop an augmented- reality (AR) system for heavy-equipment operators (HEOs) in surface mining. The developed system has the potential to enhance mine safety, training and data-driven decision- making, which presents a significant step toward a more sustainable, effective and technologically driven mining training, contributing to the industry’s evolution and growth. The AR training system leverages Microsoft’s Power Platform and HoloLens 2 capacities to provide operators with detailed and immersive training guides for three mining equipment, including bulldozers, motor graders and haul trucks. AR guides combine speech controls, 3D objects, informative images and explicative videos in the real working conditions to enhance the operator’s learning process. The system has the potential to modify the training structure based on user performance and provides an efficient approach to data collection during training. This project was developed and applied through a case study in a surface mine in the Southern United States.

Feb 1, 2025

By S Marshall, A Fowler

The Augusta underground mine at Costerfield in Central Victoria has been in operation since mid 2006; however, AGD Operations Pty Ltd have explored and undertaken open pit operations in the area for over 20 years. The high-grade, narrow gold-antimony orebody is being mined using both mechanised and hand-held methods, to produce up to 70 000 tonnes per annum at ten grams per tonne gold and six per cent stibnite. AGD Operations Pty Ltd processes the ore on site using gravity and flotation to produce two products; a concentrate which is sold to Chinese smelters and a gravity concentrate which is refined off-site. The circuit achieves up to 30 per cent recovery of gold from gravity methods. There are many challenges in the underground mine, including an orebody with an average width of 300 mm, very poor rock mass conditions in the host rock and variable dips in the ore along strike, between 45¦ and 90¦. The upper levels of the mine have been developed ready for stoping; however, their depths range from 20 m to 70 m below surface in both oxide and transitional material. A major fault structure consisting of mud has been encountered underground and is associated with the orebody causing very poor ground conditions, water inflow and requiring additional reinforcement. The northern limit of the mine is defined by the proximity of historical workings in the South Costerfield mine, which is being continuously dewatered.

Jan 1, 2008

By Nissandro Domingues

Foi avaliada a possibilidade de aumentar a produtividade do aço IF processado via recozimento contínuo. Amostras laminadas a frio desse aço foram submetidas a ciclos térmicos de recozimento em escala laboratorial, empregando-se menores temperaturas de encharque e maiores velocidades de processamento que as praticadas industrialmente. Foram, então, medidas as propriedades mecânicas em tração e caracterizada a microestrutura do aço. A partir dos resultados mais promissores, bobinas foram processadas industrialmente nas mesmas condições simuladas em escala laboratorial. Em amostras dessas bobinas, foi avaliada, além das propriedades mecânicas e da microestrutura, a conformabilidade de blanks visando à garantia de atendimento dos requisitos de aplicação no cliente. Com os resultados obtidos, verificou-se que é possível produzir o aço IF satisfatoriamente, preenchendo todos os requisitos de aplicação, com um incremento de 10% na velocidade de processamento e uma diminuição de até 30°C, na temperatura de encharque. Esses resultados representam considerável ganho em produtividade no processamento do aço IF.

Aug 17, 2017

By Leiner Novaes Arêdes

Após o bobinamento com temperatura controlada, as bobinas são resfriadas até um valor próximo da temperatura ambiente para o processo de decapagem. Há uma bibliografia farta no que diz respeito à temperatura de bobinamento e seus efeitos nas propriedades mecânicas e na microestrutura do aço plano laminado a quente. Contudo, pouco se encontra sobre a influência das taxas de resfriamento pós bobinamento nas propriedades mecânicas e na microestrutura do aço, especialmente nas propriedades finais de materiais que são submetidos à laminação a frio e recozimento. O tempo médio de resfriamento com água é de dois dias. Já o tempo para resfriamento com ar é de sete dias. Estudou-se o efeito das referidas taxas na microestrutura e nas propriedades mecânicas para um determinado aço tanto após a laminação a quente como após a laminação a frio e recozimento.

Jul 30, 2018

By Michel Rodrigue, Sylvain Duchesne, Louis Racine

"LocationThe Louvicourt mine is located 20 km east of Val d'Or in Abitibi, in the northwest part of the province of Quebec. The mine is located on Highway 117 connecting Val d'Or to Montreal and very close to the main railway networkHistoryFive successive exploration attempts by Aur Resources resulted in the discovery of the large Louvicourt orebody in June 1989. Construction of the surface and underground infrastructures commenced in the spring of 1991. Milling operations commenced in July 1994. The entire project cost CDN$290 million, almost CDN$20 million less than initially estimated. The concentrator infrastructure cost CDN$64 million.Louvicourt mine is owned in partnership by Novicourt Inc. (45%), Teck Corporation (25%), and Aur Resources Inc., the administrator (30%).Brief DescriptionLouvicourt mine is the largest producer of base metals (Cu and Zn) in Abitibi-Temiscamingue. Its average daily production is nearly 4300 t of ore, for an annual production of 200 000 t of copper concentrate (28% Cu) and 33 000 t of zinc concentrate (57% Zn). After only a few weeks of operation, it had attained its objectives for the most part, and operations continue to be improved."

Jan 1, 2000

In Australia we usually define "resource" in purely material terms, and rarely relate it to intellect and human capacity. We look at the sheer abundance of our natural resources and are satisfied with the feeling that we don't really need-to rely on using our brains. Certainly our country is fortunate to have the mineral resources it does, but in many ways Australia's worst enemy is its "lucky country" syndrome because we tend to underutilise the great resource we have in the capacities of our people. Raw material exports will undoubtedly continue to contribute a major share of our export revenue, but to harness the riches our country has to offer most effectively we need the vision and planning necessary to bring together our material and human resources. There is a need not only to find, exploit and process our minerals economically, but to turn as much of our mineral wealth as possible into high value products before it leaves the country. In particular we must use our brainpower if we want to maximise economic benefit from and political influence over the strategic minerals which leave our shores. In the past we have been successful in finding and exploiting minerals because our mining industry has been in the forefront of private sector research and development. But if Australia is to have an advantage over other mineral rich countries in insulating itself from the effects of cyclical swings in commodity prices, then the future of the industry must lie even more in technological sophistication rather than depending. on such considerations as size and location of mineral deposits. To survive, our mineral industry must have the foresight and resourcefulness to make its own luck. There are two keys to increased efficiency in exploration and production and in further processing methods: enhancement of the skills of the workforce and continual improvement of R&D.

Jan 1, 1986

Great new drilling results! What's so sinful about being a multi-national company? Overseas protestors flown to Australia for a free holiday How to counter the protectionist danger? Our current economic standing Over-regulation puts a convicted paedophile on the payroll The broken window fallacy Mining - A shared history Aristotle and the camels A brighter future? Something over which we do have far greater control, i.e. leadership within our own industry My challenge to you The expanding gold- producing company of which I am proud to be Chairman, Croesus Mining NL, is by definition a æmultinationalÆ. Our shareholders are based in 36 different countries, 77% of our 107 million shares are held in Australia, 23% are held outside Australia, and include New Zealand holdings of 7%. In September, Croesus Mining presented our company at the Mining 2000 Forum in Melbourne, a city caught up with multinational protestors demonstrating against multi-national companies.  

Jan 1, 2000

By Eugene Guccione

It would be extremely difficult and unfair to compare the United States to Australia when wondering about which of the two countries offers the best opportunities for running a mining operation. However, if somebody would ask "Where is the best place to mine outside the US?"-I'd answer without reservations: Australia. Some of my Australian mining friends will disagree with me for my giving their country such a high rating. And they'll probably accuse me of being an optimist by telling me, as one of them did, that "the difference between an optimist and a pessimist is that the pessimist is better informed."

Jan 1, 1977

The long-term outlook Tor Australla's traditional mining products is for flat demand and continuing low prices. This has come about because of three far-reaching changes since earlier boom days: 1. Continuing declines in intensity of usage of basic mine products; 2. The failure of newer western and third world developing countries to realise growth expectations; and 3. Continued production pressure from third world countries (and first-world primary producers) in an effort to earn foreign exchange and rectify trade balances. These trends have led to a general situation of excess supply and weak demand. In this environment, the prerequisites for survival in the mining sector are first-class mines, modern and efficient production methods, low unit costs, aggressive marketing, and products with reasonable operating margins. Many of Australia's mines meet these prerequisites. Following the A$ depreciation and widespread unit cost reductions, most of these mines will be moderately profitable at current depressed commodity prices. They are well placed to benefit from price rises if these eventuate. A new generation of mines is concentrating on a more profitable product range (gold, diamonds, uranium, mineral sands). Australia's balance of trade remains firmly dependent on the primary mining and agricultural industries (Fig. 1). Despite optimistic talk of high-tech developments, tourism and a resurgence of manufacturing, these will remain a small component of Australia's export structure.

Jan 1, 1987