Search Documents

By Glenn Buchana

El presente texto señala algunos aspectos técnicos y comerciales del dragado del depósito fluvial. Para ello, es necesario conocer el origen y desarrollo del depósito fluvial. El depósito fluvial es una masa de grava superficial, la cual es producto del desmoronamiento y erosión de rocas sólidas que contienen partículas o pepitas de oro, diamante, estaño, platino u otros minerales valiosos que proceden de las rocas o de las vetas. Entre los tipos de depósitos aluviales tenemos: depósitos aislados pequeños y poco profundos, los depósitos de mediana profundidad, depósitos profundos y los marinos. La explotación se realiza a través de tres sistemas: draga cortadora de succión, la dragalínea de cangilones y la planta de tratamiento flotante.

Nov 1, 1979

By Bror Nyman

Wide settlers are a way to decrease the linear velocities of advancing liquid phases. It has, however, been found unnecessary to risk a proper settler performance by building shallow settlers in order to avoid a so-called interface turbulence due to a too big difference between the linear velocities of the organic and the aqueous phase. This conclusion has been reached from tests using a large transparent settler model, where the behaviour of a clean interface between two advancing liquids has been investigated. Also in a more realistic case, making an organic in aqueous or an aqueous in organic dispersion to move between the liquid phases, no obstacle has been found to use a somewhat more deep and correspondingly ore slowly t10wing aqueous phase. Based on above findings, support can be given to a new trend to build the settlers slightly deeper than what has been typical for the so-called low-profile design. In this way, it is much easier to avoid an excessive air introduction and other severe difficulties, like those caused by crud moving from one stage to another. It is further shown, how gravity can be used to slow down and distribute a dispersion being fed into a settler of a VSF unit. Entrainment levels have been found to be reduced by a careful design of primary dispersion distributors and picket fences of the settler. Finally, it is demonstrated, how outlets from the side of the settler can be used to simplity interstage pumping and to decrease the rotation speed of any pumping device.

Jan 1, 1996

By Cagri Emer

In conventional mechanical flotation cells, when the size of particles exceed a particular value, that is of the order of 100 µm for metal sulphides, the recovery of particles decline rapidly. It appears that the turbulence in the agitated vessel is sufficiently intense to rupture the forces of attraction between the particles and the bubbles, so the large particles are flung off the bubbles in the turbulent field. It has recently been suggested, that a fluidized bed would be a very favorable environment in which to contact bubbles and the particles. In a fluidized bed, particles are supported by rising flow of fluid, which separates them from each other and allows them to move freely while remaining close together. In this novel method, bubbles injected into the fluidized bed are able to rise through it, colliding with hydrophobic particles, transporting them to the top of the column where they can form a froth layer that overflows into a launder. The flow in a fluidized bed is generally slow and nonturbulent, and preliminary experiments have shown, that it is possible to collect mineral particles as large as 1 mm and coal particles as large as 5.5 mm. If the upper particle size limit can be extended, there could be significant reductions in the overall energy consumption in concentrators. Calculations show for example that if the top size for flotation could be increased from 100 µm to 400 µm, there would be a reduction in grinding energy of the order of 40%. It is therefore, important to study the mechanism of coarse particle capture in fluidized beds. In this work, the factors governing the capture rate of particles, particularly the particle and bubble size, the fluidization velocity and the superficial gas velocity have been investigated, and the results will be presented.

Sep 1, 2012

By José Luiz Rodrigues Bravo

The production of electrolytic copper with assured quality corresponding to international standards, in a conventional electrorefkery of a custom smelter, is a hard and cautious task, if no advanced technologies for selective control of electrolyte impurities are available. The improper control of the amount of As , Sb and Bi in the anode that enter the tankhouse , attributable either to a bad schedule of concentrate input or to the unavailability of clean concentrates in the international market , as well as the lack of means to maintain the suitable level of these elements in the electrolyte together with other operational circumstances, can result in off-grade copper, as well as affect the starting sheet chemically and physically. This paper presents in a practical way the relationship between the operational conditions and the cathode and starting sheet quality produced at CMSA, covering the period of the last five years of operation, discusses the technologies available in the market for antimony and bismuth removal and compare the results of testwork, achieved in the laboratories of CMSA, using two resins not associated with patented technologies.

Jan 1, 1997

By C. J. V. Wheatley

Recent studies of the mineralisation at Avoca in southeast Ireland, Parys Mountain in Anglesey, and Coniston in the Lake District result in the proposal of a new metallogenetic model for mineral deposits in the Southern Caledonides. A regional pattern of metal zoning exists, an axial belt, including the major copper deposits, being bordered by areas with lead-zinc deposits. Conformable lenticular pyritic zones occur in the central belt, closely associated with acid volcanic sequences and, often, post-dating them. These zones are thought to have been formed in a marine environment, mineral growth taking place below the sediment-water interface, whereas magnetite-rich zones developed under different Eh and pH conditions. Stockworks containing appreciable copper and, in some cases, lead and zinc were developed at a later date, stratigraphically below the pyritic zones, by migrating hydrothermal chloride and metal-rich fluids. Complex lead-zinc-pyrite mineralisation resulted from the reaction between pyritic zones and the final fraction of the hydrothermal fluids. Crosscutting vein-type fissure infilling mineralisation occurs in every mineral field. These deposits apparently comprise a pulsatory metasomatic sequence, closely related to tectono-stratigraphic controls, ore localisation being influenced by the coincidence of suitable structures and pyritic shale horizons. The implications for mineral exploration are considered and it is concluded that the model offers an explanation for the existing pattern of metal zoning; and it may have wide applicability to mineral deposition in geosynclinal sequences.

Dec 1, 1971

By Lyden, Joseph P.

THE Picher Mining Field, fig. 1, which lies between Baxter Springs, Kansas, and Commerce, Okla., is the most intensely mineralized and the largest zinc-lead ore producing area in the Tri-State District of Missouri, Kansas, and Oklahoma. It has a vast lateral extent of underground workings that is unequaled for the observation of the geology of zinc-lead ore bodies in sedimentary horizons; and thousands of churn drill holes in the unmined areas supplement the underground observations with useful data for the interpretation of the geology. This paper is confined to the ore deposits of the Picher mining field. The reader is referred to the bibliography for the general geology of the Tri-State district which has been ably covered by many geologists. The writer was co-author of several publications on the Tri-State district.- This paper is necessarily a repetition of parts of those publications but contains a few changes and additions on the deposition of the minerals. The parts of this paper concerning mineralization maps and pipe slump-structures are not covered in the above publications.

Jan 1, 1950

By WILLIAM SLOAN

B RITISH COLUMBIA in its mining activities is going ahead by leaps and bounds both in development and production. Mineral production for 1925 was $61,492,242 in value as compared to $48,704,- 604 in 1924, or an increase of about 26.2 per cent. This is a new record. It is the first time in the history of mining in British Columbia that we have gone over the fifty million mark. But we have got in the habit of making new records. The year 1924, with its mineral production of almost forty-nine million was a new record. And I am confident that when the mining history of 1926 is written it will be found that we have established yet another new record and that we can report another 25 per cent increase over 1925. What is the explanation? It is not only that the world is settling down, and settling up, after the war. It is not only that in the rebuilding, the refashioning in which all nations are busily engaged, the metals that come from our mines are needed. More than anything else, at least as far as we are concerned, it is because British Columbia has the resources and the fact that the province has been fortunate in recent years in finding men with the enterprise and the vision required to push ahead the labor of their development. From the ranks of our own people in Canada we have prospectors who have faith, energy and requisite knowledge. They are combing our hills season after season and they are of the type of manhood that does not know the meaning of the word quit. More and more these men are learning the importance of the guidance furnished by geological reports, and to an ever increasing extent such reports, thanks to the valuable work of the Canadian Geological Survey, covering areas little known to man, are made available to them-but it is recognized that in the opening up of our Province, containing within itself 372,000 square miles, it is essential that we should have the cooperation of our cousins on this side of the line as well as of our fellow citizens of the Dominion and of the Mother Country.

Jan 1, 1926

By D. W. Frommer

Processing nonmagnetic taconites by selective flocculation-desliming and flotation requires large volumes of water. If impounded without treatment these off-process waters require excessively large areas for containment. To discharge the waste water into natural waterways would contribute to stream pollution and likely would not be permitted. In Bureau of Mines experiments conducted in the Twin Cities Metallurgy Research Center&apos;s 900-lb/hr pilot plant, approximately 85 percent of water requirements for the flotation-based treatment of a Michigan nonmagnetic taconite were met by reclaimed water. Water reclamation of the off-process streams from flotation was accomplished by controlled additions of lime, sodium carbonate, and a synthetic flocculant to reduce turbidities to <1,000 ppm equivalent Si02, while maintaining a Ca(II) content of 516 ppm in the finished effluent. Flotation concentrates of good quality were obtained using the reclaimed water. The cost of chemicals used in water reclamation was approximately equal to the savings in flotation reagents attributed to recycling of the water.

Jan 1, 1970

Discussion of the paper of E. J. Hall and C. W. Drury, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 78, June, 1913, pp. 1059 to 1066. A. M. SMOOT,* New York, N. Y. (communication to the Secretary +) :-The nails method is given in many text books on assaying as a standard method for gold or for gold and silver in ores. It appears to be taught in the laboratories of technical and scientific schools as a standard method, and to some extent it is used by assayers in actual practice, although the class of ores to which it may be applied is limited to those free from reducible metallic compounds, the metals of which would enter the lead button. The experiments of Messrs. Hall and Drury show the inaccuracy of this rnethod for silver, in heavy sulphides, but not so clearly the short-comings with regard to gold. It seems certain that low silver is caused by the solubility of silver in iron-alkali sulphide as compared with its solubility in molten lead; that is, silver is distributed between iron-alkali sulphide and metal in the charge in proportion to solubility at the particular temperature of the fusion. Lead is a fixed quantity in these assay charges, but iron-alkali sulphide increases with increased sulphur, so the more sulphur in the charge, the lower the silver results.

Jan 11, 1913

By L. Alagha, J. L. Corchado-Albelo

To address the U.S. Department of Energy’s critical minerals strategies regarding rare earth elements (REE) in the U.S.A. This study evaluated apatite-rich mine tailing from the historic Pea Ridge Iron Mine (PR) for possible enrichment of REE by the froth flotation process. Comprehensive characterization studies were performed on the tailing samples to quantify the REE content, identify the REEbearing minerals and their liberation behavior. The aforementioned characterization studies were: x-ray fluorescence analysis (XRF), inductively coupled plasma mass spectrometry (ICP-MS), and TESCAN’s Integrated Mineral Analysis (TIMA). The ICP-MS analysis showed that the concentrations of heavy-REE and light-REE were 8000 ppm and 3000 ppm, respectively. TIMA showed that monazite was the major REE-bearing mineral. Additionally, it was shown that monazite and other REE-bearing minerals were strongly locked within larger apatite grains. Findings from the characterization studies suggested that REE could be enriched using phosphate minerals’ direct froth flotation process. Flotation feasibility tests were performed using selected organic and inorganic iron oxides’ depressants, including polyacrylamide (PAM), in-house synthesized hybrid polyacrylamide (HyPAM), chitosan, sodium silicates, and corn starch. Results showed that the depressant’s efficiency at pH 9 was in the following order: HyPAM > chitosan > PAM > sodium metasilicate > corn starch. Zeta potential studies on the selected depressants indicated that chitosan had the highest adsorption on magnetite’s surface at pH 7. Therefore, additional batch flotation experiments using chitosan as an iron oxides depressant were conducted as a function of chitosan dosage. Results indicated that the highest P2O5 recovery of 55% and grade of 28 wt.% were obtained at 150g/t of chitosan. However, the concentrate’s highest total REE enrichment of 1.07% was achieved at a 200 g/t dosage of chitosan. The low enrichment of REE highlighted the complex mineralogy of the PR tailings and the need to implement additional beneficiation strategies before and after the froth flotation process.

Mar 2, 2022

By Xingshi Yang, Ghislain Bournival, Seher Ata

"Particle-laden interfaces are a fundamental research topic in froth flotation since the process involves particle-coated bubbles in both the pulp and the froth phase. In most experimental studies the characteristics of the particle layer in multi-bubble systems are poorly defined. An experimental setup has been developed based on a Langmuir-Blodgett (L-B) trough. The modified trough allowed introducing an air bubble beneath the particle monolayer formed at the air-water interface which made the study of the interaction between the bubble and the monolayer under various pH values possible. The monolayer characteristics of the particles were also studied and compared in terms of surface pressure (?-A) isotherms and packing factor. On compression, the particles formed branched structure at high pH whereas a uniform monolayer was formed at lower pH. Observations related to the behavior of particles during compression and expansion cycles, and the coalescence of a bare bubble with the flat particle laden interface were provided and the implication of the results for flotation process was discussed.INTRODUCTIONFroth flotation is known for its versatility and ability to concentrate low-grade, complex ores. It is considered a physico-chemical process in which particles attach to air bubbles, depending on their hydrophobicity as well as other factors, and are carried to the surface to form a froth layer. Reagents are used to stabilize bubbles and the froth layer (Pugh, 1996). However, particles, which are carried by the bubbles or entrained, significantly contribute to the stability of the froth phase (Ata et al., 2003; Zanin et al., 2009; Bournival et al., 2015a). Their relevance in mineral processing has led to a number of fundamental studies on the effect of particles and their properties on the process of froth flotation.Flotation systems are particularly difficult to characterize due to the broad range of properties of particles (e.g. size, liberation, hydrophobicity, etc.) and inconsistent operational conditions (e.g. changes in water quality, reagent addition, etc.). Several studies have made the use of well characterized particles in laboratory conditions. Such studies allowed the finding of an optimal contact angle for the stabilization of the froth phase (Johansson and Pugh, 1992; Ata et al., 2002). Froths have a large number of bubbles so that individual interactions are not observed. The study of two bubbles allows to determine the stability of the bubbles, with particles, and to some extend the stability of the bubble-particle aggregate (Gourram-Badri et al., 1997; Bournival et al., 2015b). The removing of particles between two bubbles may also be studied from a Scheludko cell (Johansson and Pugh, 1992) or by observing a bubble with a flat interface (Sethumadhavan et al., 2002). However, these systems provide limited information on the arrangement of the particles."

Jan 1, 2018

By B. A. Massey

Sooner or later, we&apos;ll encounter a subordinate, peer, or boss that will test our management skills to the limit. The chances are good that our formal educations have not fully prepared us to effectively handle the situation, and through trial-by-fire, we have learned that the management of people is often as much an art as it is a science. Assertiveness - as opposed to agressiveness - is basically positive persuation. Assertive management techniques can help combine the art and science of managment to sell ideas, accomplish goals, direct the workforce, and generally promote the corporate - as well as our own - objectives

Jan 1, 1986

By C Paoletti

About 15 years ago the debate on the reliability of sampling procedures for agricultural food and feed commodities was initiated by a few brave scientists who questioned the representativeness of what, at the time, were routine sampling procedures established exclusively on the basis of tradition and practical feasibility. Over time several national and international organisations contributed to the discussion, developing standards and publishing papers either to underline the fact that sampling is always a source of error, in itself, which cannot be overlooked, or to minimise the relevance of sampling on the basis of argumentations linked to time and money limitations. The latter dominated, but is nevertheless impossible to accept from both a scientific and a responsible management perspective. Here the author presents an historical overview of these past 15 years, illustrating the most controversial issues, reporting major achievements in food/feed sampling, highlighting milestones, as well as unresolved problems that still need the attention and contribution from the sampling community. The need to incorporate Theory of Sampling (TOS) into food/feed safety assessment (pre-market), as well as into food/feed safety monitoring (post-market) has recently been highlighted, and the practical applicability of TOS to base food/feed safety decisions on representative sampling, has been explored and documented via concrete examples of risk analysis in different areas of food/feed industrial production chains. Now it is time to move forward and ensure that TOS is fully integrated into the well-established Food and Agriculture Organization (FAO) / World Health Organization (WHO) risk assessment approach, in order to guarantee a transparent and correct universal frame for risk assessment and the subsequent management decision-making process. WCSB8 offers the ideal platform to explore the best way to do so, switching from a theoretical discussion of correct sampling principles for food and feed agricultural commodities to practical recommendations in the interest of consumers, worldwide. These 15 years have also been a personal journey of interesting dimensions, indeed a veritable roller-coaster ride in-and-out of the scientific, technological, industrial and (last but not least) regulatory worlds. The start was WCSB2 in 2004, when I flew to Australia to discover if in other areas sampling had been identified as an unavoidable issue and, if so, what the solution was. There, I found a good travel companion who today is still on my side, to assemble the puzzle and explore how to shape the future, to concretely answer to the 15 years’ quest for proper sampling in the assessment and monitoring of food/feed safety.CITATION:Paoletti, C, 2017. Assessing and monitoring food and feed safety – a 15 year quest for proper sampling, in Proceedings Eighth World Conference on Sampling and Blending , pp 39–44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By A. T. van Zyl, M. Mthenjane, M. J. Cole

Growing global concern over the impacts of climate change, attributable largely to fossil fuel energy sources, has led to the widely shared goal for a ‘just transition’ to cleaner energy and reduced dependence on carbon-based fuels. As the world’s 14th biggest CO2 emitter and being particularly vulnerable to the impacts of climate change, South Africa must embark on a just transition pathway. This paper reviews expected coal mine closures and associated community vulnerabilities and local governance challenges in South Africa. Decommissioning schedules for all coal-fired power stations and operating coal mines are plotted, and 69 mining host communities and 21 municipalities are mapped, classified, and described. Community socio-economic profiles are measured using a set of SDG indicators and census data and municipalities assessed through financial audits. Our research shows that five coal-fired power plants (8.9 GW) and 15 coal mines (29.5 Mt/a) will probably close by 2030, and a further four plants (14 GW) and 23 mines (106 Mt/a) by 2040. Thus, the shift to cleaner energy will likely occur without the premature closures implied by the just transition. The impact of mine closure on the 2.5 million residents of host communities will be significant, particularly as levels of income, employment, and education are already very low and many municipalities are in financial distress. The South African approach to the just transition needs to take local realities into account and the narrative must support an effective transition that does not undermine energy security and economic growth.

Jun 5, 2023

By N Power, R Hassell, E Jones

Wiluna Mining Corporation are progressively re-entering the old Wiluna underground mining complex. The existing underground was abandoned in 2013 by previous owners and left to flood with water levels reaching above the East Pit portal and Happy Jack Pit portal and up to 300 m below surface in the Bulletin underground. Re-entering the mine commenced in 2017 with dewatering of the Bulletin decline. The underground development had been previously supported with friction bolts, with weld mesh in places. Until mid-2021 rehabilitation requirements were based on an external visual inspection of the installed ground support scheme. However, several incidents involving falls of ground due to corroded bolts have occurred during this time, showing that this approach was inadequate. The challenge the operation faced was should the entire decline be rehabilitated, the implication being not only a large rehabilitation cost but also the impact of severe delays to the mining schedule. The question was asked can the operation better understand the level of corrosion damage and potentially optimise rehabilitation requirements. A proposal to use a systematic approach to assess corrosion by environmental condition mapping, visual external corrosion assessment, and internal corrosion assessment via borehole camera inspections was provided and accepted by Wiluna Mining Corporation. The objective of this work was to produce a three-dimensional map showing the degree of corrosion on the reinforcement systems in the capital infrastructure, this would then be used to risk assess and prioritise rehabilitation requirements. This paper summarises the approach, methodology and results that provided the Wiluna mine planning team with information to enable planning of resources and budget to justify priorities of rehabilitation.

Nov 29, 2022

By Fouad Faraj

For every blast pattern, zones of unique material types need to be classified before mining. Most material types can be summarized into different kinds of ore and waste. Blocks generated from blasthole assays are too small to be selectively mined, so areas with a single material classification meeting the mine’s selective mining unit must be defined. Current industry standard practices are to manually draw ore/waste dig limits, but this process is subjective and results in quantities of dilution and ore loss that can be improved upon to enhance the profitability of mining operations. In this study, two weeks of production data from a homogeneous copper (Cu) porphyry and heterogeneous manto-type Cu deposit were used to assess the variability in the hand-drawn dig limits of 20 geologists, mining engineers and ore control specialists, which were compared with the optimal ore/waste delineation. The profit for 20 distinct hand-drawn dig limits for the homogeneous mine varied by 3.7 percent, from $10.5 million to $10.9 million, averaging at $10.8 million. The percentage was nearly double for the more heterogeneous mine at 5.9 percent, from $17.9 million to $19.0 million, averaging at $18.6 million. Using the optimal ore waste delineation, the profit increased to $11.0 million (1.9 percent increase) and $19.3 million (7.0 percent increase) for the homogeneous and heterogeneous deposit, respectively. The natural variability, diggability requirement and selectivity are identified as the main drivers of ore loss and dilution. Recommendations are provided for reducing the subjectivity in manual hand-drawn dig limits by integrating dig limit optimization algorithms as a tool to assist practitioners.

Oct 1, 2024

By R H. Yoon, M Gupta, A Noble, K Huang

Froth flotation is the most commonly used separation technology in the mineral industries. Given the complexity of the pulp and froth phases as well as the multitude of operational parameters that influence flotation performance, purely fundamental models with strong predictive capacity are limited. As a result, accurately modelling modifications to an existing flotation circuit are challenging, particularly when using empirically-derived models from a different operating configuration. Despite these complexities, a recent publication by the authors (Huang et al, 2022) has shown that flotation rates can be accurately predicted from a first-principles model that incorporates hydrodynamic parameters (eg pulp density, superficial gas velocity, feed flow rates etc), surface chemistry parameters (eg contact angle, zeta potentials and surface tension), and size-by-class liberation data. Circuit simulations using this model were shown to be effective in predicting experimental graderecovery curves from the size-by-class mineral liberation matrix. Since the model is derived from fundamental characteristics of the flotation system, it can be used to simulate alternative circuit configurations with varying degrees of recycle. Conventional flotation circuits are operated in a closed-circuit configuration by routing the cleaner scavenger tails (CST) back to the rougher feed to provide an additional opportunity to recover the slow-floating particles. This widely-used flotation strategy has been under constant debate, and several researchers have provided evidence that open circuit configurations provide higher separation and better circuit control (Konigsman, 1985; Bulatovic et al, 1998; Thompson, 2016). Recently, Finch and Tan (2021), used linear circuit analysis to show that open circuit configurations have a fundamental advantage when stage recoveries are high. Given the limitations of these prior studies, the objective of the current work is to further evaluate the merits of the open circuit configuration through a detailed circuit analysis and simulation study incorporating the first principles model described above.

Aug 24, 2022

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck

"Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27% of the respirable coal mine dust can be attributed to longwall shield movement. Developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine their ability of foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used; compressed air (CA) and blower air (BA). Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For CA foam in 3.3 m/s (3.3 m/s (650 fpm)) ventilation at 3 minutes after application, 98% of agent A was intact, while 95% of agent B was intact on the roof. At 30 minutes after application 94% of agent A was intact while only 20% of agent B remained. For BA in 3.3 m/s (3.3 m/s (650 fpm)) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 minutes after application 74-92% of foam agent A remained, while 3-50% of foam agent B remained. CA foam seems to remain intact for longer durations and is easier to apply than BA foam. However, more water drained from the foam when using CA foam which demonstrates that BA foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control. INTRODUCTION NIOSH personnel have visited many longwall operations at various geographical locations in the U.S., conducting benchmark surveys to characterize current operating practices and dust control measures in use. Sources of respirable dust generated from the longwall face have been identified as: intake (10%), stage loader (20%), shields (27%), and shearer (43%) [1]. Dust generated from the shearer, armored face conveyor, and the stage loader can mainly be controlled by water sprays and increases in ventilation air quantities, however, research has demonstrated limited effective controls for dusts generated by shield movements [2]. One possible approach to mitigating shield dust generation is to apply a layer of water or foam to the shield-roof interface. Once this interface is blanketed with foam or water, dust will be less likely to become airborne and contaminate the airways over the personnel walkways. Though water is an abundant and common dust control measure, roof applications have limited success because water is unable to remain in-place in adequate quantities for the necessary duration between application and shield advance. Past and current testing of foam for material properties has shown that it has longer applicability times, ranging from 10 to 60 minutes [3] and has shown better performance for dust control, ranging from 19-96% improved efficiency over water [4, 5, 6, 7, 8]. The majority of this foam dust control research has focused on dust control efficiency at the longwall shearer or continuous miner cutting drum."

Jan 1, 2017

By Peter Zhang, I. BERK TULU, Morgan M. Sears, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

Ground falls in longwall gateroad entries remain a concern in modern longwall operations. The gateroads are subject to changing horizontal and vertical ground stress induced by longwall extraction. These stress changes can result in failure of the strata around an entry leading to large deformations of the entry roof, floor, and ribs. The gateroad support systems are required to control the failed strata while maintaining safe access to the longwall face and unimpeded ventilation. This paper presents research that was conducted to better understand the stability issues in gateroad excavations and to develop procedures for evaluating support and layout alternatives for longwall gateroads. Using the results of a field-monitoring program and numerical model analysis of case histories, a conceptual model of gateroad support needs was developed. The conceptual model formed the basis for developing a set of equations that can be used to estimate likely roof sag and support loading for given roof geology and longwall-induced loading conditions. The developed equations were used to compare predicted gateroad stability to field study results, showing satisfactory agreement. The calculation procedures are used to demonstrate their application in assessing support alternatives at a case study mine. It is concluded that the developed analysis procedures provide realistic assessments of likely ground stability and can be used to evaluate alternative gateroad support systems at operating longwall mines.

May 13, 2021

By Peter Zhang, I. BERK TULU, Morgan M. Sears, Heather Dougherty, Ted Klemetti, DYKE MARK VAN, Gabriel S. Esterhuizen

Ground falls in longwall gateroad entries remain a concern in modern longwall operations. The gateroads are subject to changing horizontal and vertical ground stress induced by longwall extraction. These stress changes can result in failure of the strata around an entry leading to large deformations of the entry roof, floor and ribs. The gateroad support systems are required to control the failed strata while maintaining safe access to the longwall face and unimpeded ventilation. This paper presents research conducted to better understand the stability issues in gateroad excavations and to develop procedures for evaluating support and layout alternatives for longwall gateroads. Using the results of a field-monitoring program and numerical model analysis of case histories, a conceptual model of gateroad support needs was developed. The conceptual model formed the basis for developing a set of equations that can be used to estimate likely roof sag and support loading for given roof geology and longwall-induced loading conditions. The developed equations were used to compare predicted gateroad stability to field study results, showing satisfactory agreement. The calculation procedures are used to demonstrate their application in assessing support alternatives at a case study mine. It is concluded that the developed analysis procedures provide realistic assessments of likely ground stability and can be used to evaluate alternative gateroad support systems at operating longwall mines.