Search Documents

By F D Durao, Muge F. H, Rogado J. Q

In the scope of the project named CAPUME II (EEC BRITE/EURAM contract - project MA2M-CT90,-0042(SMA)) for the development of an integrated mine planning system for underground mines, two of the main tasks were the development of a short-term mining planning procedure (module) and a numerical simulator of the mineral processing plant of Pirites Alentejanas - PA. The short-term mining planning module defines the mining sequences by solving a constrained minimisation problem. The ore grade variability is the objective function subject to the geometrical constraints of the mining method and to the maximum of `internal blending'. The optimisation problem is solved by applying a dynamic programming algorithm. The plant simulator is an essential tool of the planning system allowing the preview of metal grades/recoveries of copper, lead and zinc of concentrates streams, given the corresponding metal assays of the run-of-mine ore, defined by the short-term mine planning module. This way, the management can plan the short-term mining operations (the weekly sequence of exploration blocks and the internal planning) in order to fulfill given required conditions, based on a shipment schedule and on a purchaser's formula. In this paper, after a short description of the short-term mining planning module and of the simulation package named SIMUL, a synthesis of the main model development steps and the results of some simulation runs are presented and discussed.

Jan 1, 1995

By J. T. Clancey

The potential inadequacy of natural gas reserves to supply projected requirements in the 1980's has been pointed out.(1,2) As a result, interest has arisen in the development of new, potentially low-cost processes for the conversion of coal into high BTU gas. In June, 1964, the office of Coal Research (U. S. Department of interior) and Consolidation Coal Company (now a subsidiary of Continental Oil Company) entered into a contract to continue work on coal gasification utilizing the Consol CO2 Acceptor Process. Work under this contract has been specifically directed toward the use of lignite as the carbonaceous feed, although the process is also applicable to non-caking subbituminous coals. The primary objective of this work was to establish the technical feasibility in continuous bench-scale equipment, of the novel features of the C02 Acceptor Process. Secondary objectives were the testing of commercially obtainable acceptors and the design and economic evaluation of a commercial facility. The bench-scale process development has been completed successfully and the construction of a large pilot plant at Rapid City, South Dakota, has been authorized. It is the purpose of this paper to review the technology of this new gasification process and to present the current projected economics of a plant producing 250 MM SCFD of pipeline quality gas.

Jan 1, 1969

By John Fred Rivera

Since its inception during the hectic days of World War II, Kaiser Steel Corporation has developed and maintained a solid reputation as a progressive company with an incessant penchant for attempting innovative ideas to improve its stature in the American and world corporate framework. The very latest in technology is aptly demonstrated in the new Basic Oxygen Process recently placed into operation at Kaiser's huge Fontana Steel Mill. Daring ventures such as this and other developments on pollution control devices have propelled Kaiser Steel Corporation into the forefront as the largest steel producer in the western United States. Kaiser Steel's boldness and willingness to attempt new ideas and the very latest in technology is by no means limited to its steelmaking operation. It extends into every phase of Kaiser's corporate structure.

Jan 1, 1979

By Schrade F. Radtke

THE law of our present industrial society is the law of the jungle. By this I mean survival of the fittest. I do not refer to man or animal or the development of superior genetic strain. Rather do I refer to one's product, one's process, or one's material of construction. Each must perform in a superior manner or it is doomed to extinction; it must be steadily improved so that it can meet the competition of ether materials, of other equipment, or other processes. We have before us the classic examples of the horse and buggy vs the automo-bile, cf silk vs nylon, of the steam locomotive vs the diesel engine; in each case, a superior product has virtually wiped out its predecessor. Furthermore, a product, process, or piece of equipment is sold on its performance, together with engineering data which define its •characteristics and performance. For the most part, the present day sales-man must deal in terms of engineering performance of his product; he must know competitive materials -their strength and limitations as well N either old fashioned salesmanship, tradition, nor custom could have saved the horse and buggy from extinction; a superior product which has been steadily and con-sistently improved won out, 'and in turn, this change-over caused a dramatic• change in our whole way of life.

Jan 1, 1960

By Richard Harvey, Robert Paul Mawer

In recent times there has been an increase in the demand from Steel plants for a technology that offers the most economical environmentally sustainable solution. In terms of blast furnace off gas cleaning this has seen a drive towards Cyclone technology replacing the older Dustcatchers. Cyclone technology can achieve dust removal efficiencies as high as 95% increasing the dust yield at the primary stage of gas cleaning. The dry dust (rich in Fe and C) can then be recycled to the Sinter Plant or Blast Furnace. Capture of dust at this stage also has the benefit that sludge generation from the secondary stage is also reduced meaning less waste to landfill and / or recovery of some of the by-products for further use. Primetals Technologies already offer a state of the art Tri-Axial Cyclone installed on many sites world-wide, however, this paper focuses on a hybrid of this technology, the DustClone. The DustClone is a low CAPEX unit that is essentially a Cyclone housed inside the Dustcatcher. This unit is aimed at operators who may be carrying out smaller scaled shutdowns / repairs that normally have a reduced CAPEX. This paper describes the technology that Primetals Technologies have developed.

Oct 1, 2019

By H. Dean

"Mine hoisting machinery, of which wire rope is an essential part, is developing, in Canada as well as in other parts of the North American continent, into highly sophisticated equipment. Heavier payloads are now required to be raised from steadily increasing depths at higher rates of speed and production. These hoisting conditions have, of necessity, brought about a major change in the production of steel roping wires and the wire ropes manufactured from them.Operators and designers of hoisting equipment are requesting a very much more efficient ratio of strength to weight in hoisting ropes, so that heavier loads may be raised from greater depths by ropes which will provide a predeterminable life span on which the operator may depend.The cost of wire rope to the operator is very low indeed, usually less than $0.01 per ton of payload, but the cost of unexpected shutdown periods, due to rope maintenance or change, can be extremely high -particularly in operations where a continuously high rate of production is an absolute necessity. Mine hoist ropes with a higher strength to weight ratio are now being made and used in some areas of Canadian mining, and a general understanding of the performance we may expect from them is required."

Jan 1, 1968

By Milton Gomez, Nico Sutmoller

Low-density cellular concrete (LDCC) was first introduced to the market in the early 1900s and since then has made continuous technological advances. There are two primary types of LDCC: permeable and non-permeable. Both types of cellular concrete offer advantages in different types of geotechnical engineering applications. Because of its unique characteristics of low density, high compressive strength, and high fluidity during placement, LDCC offers an effective solution for a wide variety of engineering applications, and in many cases provides a more cost-effective, labor saving alternative to traditional fill materials. This paper will review the history, characteristics, and technological advances of LDCC, highlighting multiple real-world case studies that showcase the high-performance capabilities of both permeable and non-permeable LDCC.

Dec 1, 2022

By J. W. Rinard

This paper is intended to introduce "non engineers" to one of the more misunderstood pump performance parameters, NPSH (Net Positive Suction Head). This basic presentation and resultant review should provide a practical understanding of NPSH and what its importance is to pump operation and reliability.

Jan 1, 1996

By Stefan Swartling, Rudy Lyon, Donald A. Bruce

"Since their first production application in Sweden in 1995, water-powered, down-thehole hammers (WDTH) have been used throughout the world in many different drilling applications, total lines, over 25 million lineal meters of drill hole. This paper reviews the history and principles of down-the-hole drilling (DTH) in general with both air and water, before focusing on the details of WDTH hammers. A summary of the numerous and considerable advantages of WDTH drilling is provided, with particular emphasis on their superior productivity, smaller deviation, applicability in sensitive/urban conditions, environmental protection and much reduced energy requirements.HISTORICAL PERSPECTIVE ON PRODUCTION DRILLING METHODSAir-flushed drilling with top hammers began in the mining industry in Sweden in 1873, while down-the-hole (DTH) drills, again with air flush (and activation) became operational in 1950. During that same time interval, Simon Ingersoll had patented the first steam-powered, top hammer rock drill to provide higher productivity in blast hole drilling. It is well known that water, as an activating, flushing and cooling medium, has many significant advantages over the use of air. However, it was not until 1973 that top hammer systems (either air or hydraulically activated) for larger rigs were adapted to the use of water flush, typically via “under the head” swivels.The concept of a water-powered, down-the-hammer (WDTH) had been explored prior to G. Drill acquiring the original patent from Atlas Copco in 1988. LKAB, a huge underground mining company owned by the Swedish Government and providing about 90% of the European Union’s iron ore, purchased G. Drill in 1991 and encouraged the commercial development of the WDTH. The first full-scale WDTH production works were carried out for LKAB in 1995, since when over 25 million lineal meters of drilling have been recorded in both underground and surface applications.In 2001, G-Drill was renamed Wassara, which today still holds the worldwide patents for WDTH technology. Regarding North American usage, the first significant application was by Advanced Construction Techniques (ACT) Ltd. during the test grouting program conducted for the U.S. Army Corps of Engineers at McCook Reservoir, Chicago, in 2002. Since then, WDTH has become the tool of choice for specialty drilling and grouting contractors on dams and other major structures throughout the U.S."

Jan 1, 2015

By Frederic Benard

THIS paper constitutes a preliminary report on experimental work done to date on the anode-furnace treatment of blister copper containing relatively high percentages of nickel. The investigation has not been completed but results obtained to date are considered of sufficient interest to warrant publication. Blister copper treated by the Ontario Refining Co. originates from the Copper Cliff smelter of The International Nickel Company of Canada, of which the former is a wholly-owned subsidiary. The blister as received contains from 0.50 to 1.50 per cent Ni, and in this respect differs from that treated by other refineries on this continent. During the anode-furnace treatment, only a portion of the nickel content is removed, and of the amount remaining in the anodes a varying percentage is found in the anode slimes. This necessitates a more extensive treatment than ordi-nary, nickel-free material. Sometimes it is necessary to repeat roasting and leaching operations several times before the nickel content is low enough to permit the slimes to proceed to the doré furnace. This, besides increasing treatment charges, causes greater selenium stack losses and involves a longer tie-up of precious-metal values. Therefore this investi-gation was undertaken with the aim of determining the factors influencing the diversion of nickel into the anode sludge. From experience it was known that by keeping the nickel content of anodes at 0.55 to 0.60 per cent maximum a relatively satisfactory slime resulted. One avenue of attack therefore was developing improved elimination in the anode-furnace treatment so that the anode content mentioned above was not exceeded. Another angle was to improve the solubility, during electrolysis, of the nickel constituent in the anodes, thus decreasing the percentage diverted to slimes. It may he mentioned here that nickel dissolving electrochemically and entering the electolyte pre-sents no difficulty from a treatment standpoint. Both of these approaches were studied and are discussed sepa-rately below.

Jan 1, 1938

By Frederic Benard

THIS paper constitutes a preliminary report on experimental work done to date on the anode-furnace treatment of blister copper containing relatively high percentages of nickel. The investigation has not been completed but results obtained to date are considered of sufficient interest to warrant publication. Blister copper treated by the Ontario Refining Co. originates from the Copper Cliff smelter of The International Nickel Company of Canada, of which the former is a wholly-owned subsidiary. The blister as received contains from 0.50 to 1.50 per cent Ni, and in this respect differs from that treated by other refineries on this continent. During the anode-furnace treatment, only a portion of the nickel content is removed, and of the amount remaining in the anodes a varying percentage is found in the anode slimes. This necessitates a more extensive treatment than ordinary nickel-free material. Sometimes it is necessary to repeat roasting and leaching operations several times before the nickel content is low enough to permit the slimes to proceed to the doré furnace. This, besides increasing treatment charges, causes greater selenium stack losses and involves a longer tie-up of precious-metal values. Therefore this investigation was undertaken with the aim of determining the factors influencing the diversion of nickel into the anode sludge. From experience it was known that by keeping the nickel content of anodes at 0.55 to 0.60 per cent maximum a relatively satisfactory slime resulted. One avenue of attack therefore was developing improved elimination in the anode-furnace treatment so that the anode content mentioned above was not exceeded. Another angle was to improve the solubility, during electrolysis, of the nickel constituent in the anodes, thus decreasing the percentage diverted to slimes. It may be mentioned here that nickel dissolving electrochemically and entering the electolyte presents no difficulty from a treatment standpoint. Both of these approaches were studied and are discussed separately below.

Jan 1, 1938

By D. Reddish

The combination of free standing steel supports, such as arches, and rock bolts (mixed support) has Frequently been in used in UK coal mine roadways when it is considered that the strata and/or environmental conditions would not be suitable for rock bolts solely. However, how such mixed support systems operate is not fully understood. Due to the differences in the support method provided by rock bolts and free standing steel, the total support generated is not simply a case of adding the contribution to the support of the roadway given by the two systems. This paper describes a numerical investigation into mixed support systems when used in coal mine roadways. A series of 2D and 3D geomechanical models are described and the method of modelling the rock bolts and steel supports in coal mine tunnels is discussed. The numerical models described include rock boltd only roadways, steel supported roadways and mixed supported roadways in a variety of geological and in-situ stress conditions. Conclusions are formed that allow an insight into mechanisms of strata reinforcement provided by the support systems modelled. Further to this, a review of the numerical modelling of pre-tensioned rock bolted systems is described identifying the contribution to support efficiency given by the adoption of tensioning in full column resin anchors. The results obtained highlight that the effectiveness of the pre-tensioned load is dependant on the rock mass quality and in- situ stress level at the site where it is to be used.

Jan 1, 2004

By S Ravn

Under platform exhaust (UPE) systems are often designed into metro stations as a means of removing heat generated by trains as they come to a halt in the platform. These systems are designed to extract heat from the brakes and brake resistors directly at the source in order to capture as much heat as possible before it can enter the public areas of the station, or contribute to the temperature build-up in the tunnels. Due to space requirements for the associated duct and air handling units, the UPE plays a significant role in the geometric design of the platform and station as a whole.In recent years questions have arisen as to the effectiveness of UPE systems. However, very little data is available for designers to use when making important decisions on the station designs for new metro systems. This is important as significant savings could be achieved by omitting or re-designing these systems for new build stations; not only due to the capital costs of space provision for the duct itself but also due to the associated operation and maintenance cost of the UPE system.This paper will present recent measurements of the UPE system of the Copenhagen metro together with one-dimensional (1D) simulations, looking at typical dispersion of heat into the station plenum box and air exchange through draught relief shafts as the train enters the station in order to evaluate the effectiveness of the UPE system. The aim of this paper is to disseminate the results of measurements and analysis to increase awareness of the issue and to provide discussion relevant to designers in their evaluation of heat removal systems in new build station designs.

Mar 8, 2011

By Isa Nozari, Asghar Azizi

The extraction of copper from sulfate leaching liquor was investigated using Acorga M5640 commercial extractant in kerosene diluent. The effects of important factors such as the extractant concentration, contact time, liquor pH, and temperature were examined on the separation factor Cu/Fe and the extraction efficiency of copper. The results indicated that nearly 92.32% copper was extracted from the leach liquor at 10% (v/v) Acorga M5640 concentration, 1:1 aqueous/organic phase ratio, 20 min contact time, pH 2.5, and 25 °C temperature. Also, the further increase in the values determined had no positive impact on the extraction of copper. Under these conditions, the separation factor Cu/Fe was obtained about 29.64. The extraction mechanism was studied applying the plot of log(D) – 2 pH against log [extractant] and it proved the association of two moles of Acorga M5640 for the extraction of one mole of copper. McCabe–Thiele diagram was constructed and a single-step extraction process was found to obtain themaximumextraction. Additionally, thermodynamic datawere investigated and the extraction process was endothermic and non-spontaneous at 298 K (ΔH = 27.05 and ΔG = 15.52 kJ mol−1). Moreover, the loaded organic phase was stripped and 80.94% copper was recovered after 20 min using 10% sulfuric acid concentration.

Jul 31, 2020

By M. C. Harris

"Excess Gibbs energy is a thermodynamic parameter which quantifies the difference between the value of the Gibbs energy for a real mixture and that for an ideal mixture. More specifically the partial molar excess Gibbs energy of a species (i) in a mixture is indicated by the change in the overall excess Gibbs energy of the solution as the number of moles of species (i) changes while keeping temperature, pressure and the number of moles of all other species in the solution constant. Generally it is obtained from the activity coefficient which in turn can be obtained for a species in a mixture using a variety of models. The most widely used method is to use UNIFAC. Flotation is probably the most important process in the concentration of minerals and requires the use of reagents such as collectors and frothers. There is abundant experimental data which illustrates that collectors of different alkyl chain lengths will change the contact angle and that frothers of different structures and molecular weights will result in changes in key flotation properties such as froth behavior, surface tension and critical coalescence concentration. In this paper it is shown that there is a strong linear relationship between measured parameters such as froth volume/height, surface tension, critical coalescence concentration and contact angle and the partial molar excess Gibbs energy of the molecules used. Proposals are made to explain these correlations.INTRODUCTIONAs is well known froth flotation is arguably the most widely used process in the separation of minerals. In broad terms the process relies on the use of reagents known as collectors to adsorb onto a mineral surface and thus render the mineral particle hydrophobic. Alkyl thiolates are very commonly used for this purpose. The hydrophobicity is induced as a result of the alkyl group’s molecular structural properties which results in it forming a non-ideal mixture with the process water. Surfactants (or frothers) are typically alcohols and are known to lower the surface tension of the system and also inhibit bubble coalescence and reduce bubble size. Since alcohols are polar they will also form a non-ideal mixture with water. The hydrophobic mineral attaches to the bubble and rises to the froth phase where the valuable mineral is recovered as a concentrate. Frothers have often been characterized using the so-called HLB (hydrophobic-lipophilic balance) number but recently it was shown that the use of activity coefficients (?) or excess Gibbs energy (G ex ), which is calculated using equation (1) is a much more appropriate way to describe the behavior of these reagents in non-ideal mixtures with water (Corin and O’Connor, 2014)."

Jan 1, 2016

By S Chaudari, T Ren, T Harvey

Management of respirable dust on longwall face remains a challenging issue for mine operators, particularly for the new generation of thick seam longwalls. A fundamental understanding of the airflow behaviour around the shearer is critical for dealing with the dust control issue on longwall faces. Computational fluid dynamics (CFD) modelling techniques have been used in this study to conduct a detailed investigation of the air and respirable dust flow patterns around the longwall shearer. Three CFD models have been developed to represent different longwall cutting heights. The results of these modelling studies tallied well with field measured airflow data from different mines. The validated thick seam longwall face model was then used for detailed parametric studies to simulate the effect of various parameters and dust control concepts. The dust control options investigated include various spray configurations, shearer clearer, modified cutting sequences and shearer scrubbers of various capacities to minimise the respirable dust migration towards the walkway area of the longwall face. This paper presents a summary of the results of these CFD modelling investigations.

Jan 1, 2005

By M. S. Klima

A 25-mm diameter dense-medium cyclone was tested to investigate the effects of geometry and operating conditions on cyclone performance when processing -150 I'm coal. The emphasis was on examining those variables (e.g., flow rate and inlet velocity) which impact the separation kinetics (specifically the number of g's and the mean retention time) and the occurrence of apparent bypass. Apparent bypass, indicated by partition curve "tails", results from the short circuiting of the feed coal to one or both of the product streams and represents a loss and/or contamination of the clean coal. This paper presents the results for this series of tests.

Jan 1, 1993

By G Davison, C Rossimel, M Bouazza

Expanding rock bolts anchor within a rock mass more efficiently than non-expanding varieties. This is of great importance in weak ground conditions, where grouted friction bolts perform less efficiently than in good ground conditions. Filling a Split Set with demolition concrete has been shown to double the load-carrying capacity when compared to conventional use of Split Sets. This report details verification of these results by installing and pull-testing 14 Split Sets of varying grout conditions within in a fault zone. These Expanding Split Sets achieved loads double and triple that of ungrouted and normally grouted conventional Split Sets. A literature review and chemical analysis were conducted to understand the expansion process better. It was found that 20 per cent more calcium is included in expanding cement, which is responsible for its growth. Factors most affecting the expansion process were identified. Furthermore, the expansion rate of a bolt outside a borehole was measured and 6 mm of expansion across its diameter was found. The compressive properties of the cement were compared with other types, due to expanding cement becoming uncohesive after the expansion process is complete. When confined within a Split Set, compression testing demonstrated that this grout is just as strong and rigid as normal grout. Finally, the bolts were tested by shear and it was found that the Expanding Split Set (ESS) has a similar shear capacity to grouted Split Sets, which is 70 per cent higher than that of ungrouted Split Sets. These results enabled the mechanism for improved performance in weak ground conditions to be verified. Expanding grout will expand the Split Set into its borehole of varying diameter and lock it into place, creating increased friction and resistance to pull-out. This paper shows that ESSs can be a useful reinforcement technique in weak ground conditions.CITATION:Rossimel, C, Davison, G and Bouazza, M, 2014. An investigation of expanding split sets in weak ground, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 159–170 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018

By S. Banisi, A. Ghasemi, S. Zare, F. Ghorbani, E. Nematollahi

"Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Working at the maximum operating capacity of comminution equipment plays a significant role in the efficiency of the circuit. Appropriate design of cone crusher feed box could result in the choked crushing which is known as a vital factor in achieving target performance. In this research, the non-uniform cone crusher feeding at the Sarcheshmeh copper complex was studied and appropriate measures were taken to solve the problem. The problem resulted in non-uniform and high wear rate of crusher liners and high fluctuations of power draw. In recent decades, the discrete element method (DEM) has been applied successfully to study the effect of different factors on the behavior of particles flow. In this work, various designs for feed box were tested using an in-house developed DEM software called KMPCDEM©. The best feed box design obtained from the simulations was selected, constructed and installed in of the cone crushers. The new feed box design resulted in more uniform feed distribution on the distributor plate of crusher indicated by a reduction of the standard deviation of power draw measurements from 13 to 3 kWh. The better control of the crusher, 49% increase in the crusher throughput and finer and narrower product size distribution were the main outcomes of the installation of the new feed box. Furthermore, the wear rate on mantle and liners of crusher not only decreased but it also became uniform.INTRODUCTION Comminution is the most energy intensive operation which constitutes the major portion of operating and capital costs of the mineral processing plants. Reaching the maximum operating capacity in comminution equipment is a key sign of approaching the nominal productivity of the process. Due to the effect of crusher efficiency on the downstream circuit performance, optimization of the crushing circuits has received considerable attention (Herbst, & Potapov, 2004; Quist, & Evertsson, 2010; Li, Huiqi, McDowell, Glenn R, Lowndes and Ian, 2014; Cleary, Sinnott, Morrison, Cummins, & Delaney, 2017). Improving the performance of crushing circuits not only decreases the capital and operating costs but also increases the efficiency of downstream grinding circuits (Jacobson, Janssen, & Urbinatti, 2010). In cone crushers particles can be subjected to two different modes of compressive breakage; single particle breakage (free feeding) and inter-particle breakage (choked feeding). The maximum efficiency of the cone crusher directly depends on the type of feeding arrangement (Operation Manual, 1977). An appropriate feeding must lead to choked feeding the cone crusher. If the rate and method of feeding the crushers are correctly be executed, the maximum efficiency of the crushers could be available (Jacobson et al., 2010)."

Jan 1, 2018