Search Documents

By Andrew Scogings

The current edition of The Australasian Joint Ore Reserves Committee (JORC) Code was published in 2012 and, after a transition period, the 2012 edition came into mandatory operation on Dec. 1, 2013. There is a significant change between JORC 2004 (Clause 44) and JORC 2012 (Clause 49) for the reporting of industrial mineral resources and reserves, which should be addressed by ASX-listed players in the industrial minerals space.

By Courtney Chamberlain

The Telfer Project, Australia's newest, largest and most remote gold mine, treats 480,000 metric tonnes of ore grading 9.33 grams per tonne derived from open pit mining operations. Coarse gold is recovered by gravity concentration with jigs and further upgraded using a continuous strake, table and by amalgamation. Remaining gold is recovered in a cyanide circuit and incorporates flat bottom air agitators, CCD and stellar filters for clarification and precipitate removal. Overall recovery into bullion averages 98 percent. The mill incorporates a number of design features which allow for maximum efficiency and security using a minimum number of operating personnel.

Jan 1, 1980

By F. J. Sotillo

"Scrubbing both horizontal (drum) and vertical (attrition) are considered simple unit operations in the beneficiation of phosphate ores. In general, the operating conditions are fixed at high solids content based on the experience of the engineering or equipment manufacturing company responsible of designing this beneficiation step. Nevertheless, scrubbing is a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes, break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Therefore, it is considered that as high solids content as possible should be used to enhance particle-particle interactions (impact and rubbing) without taking into consideration the rheology of the system. However, scrubbing unit operations design requires studying the balance between the increase of particle-particle interactions with the cushion effect that may occur when slimes, clays and fines decrease the availability of free water increasing the apparent viscosity of the phosphate slurry up to that of a paste consistency. This paper presents data from laboratory tests to determine the best operating conditions for the design of these unit operations based on the highest P2O5 grade obtained with the lowest impurities for different size fractions. INTRODUCTION In the beneficiation of phosphate ores, unit operations such as horizontal scrubbing (drum) and vertical scrubbing (attrition) are considered simple unit operations. Therefore, little attention is given to the design of horizontal and vertical scrubbing during the basic engineering studies, and the detail engineering stage, the manufacturers recommending “standard” units and operating conditions based on their experience. Due diligence of several beneficiation phosphate plants at industrial scale indicates that a deficient scrubbing of the phosphate ore results in significant problems in downstream unit operations, such as classification, clarification, gravity separation, magnetic separation, flotation, dewatering, and filtration. Scrubbing is in fact a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes (clays and fines), break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Two phenomena occur, the particle-particle interaction (impact and rubbing), and the rheological effects of releasing significant amount of fines into the slurry. Therefore, high solids contents are recommended to enhance the particle-particle interactions, which may result in a change in the rheological regime of the system due to the slimes, clays, and fines decreasing the availability of free water. This increases the apparent viscosity of the system up to that of paste consistency resulting in a cushion effect that suppresses scrubbing. Under these conditions, not all fines are release and rejected (deslimed), downstream unit operations being affected by the release of clays, resulting in P2O5 losses."

Jan 1, 2017

The Boliden Aitik concentrator in Sweden processes 2,000 tph of low grade copper ore. The plant consists of five grinding lines feeding four bulk flotation banks with a scavenger concentrate regrind mill, and a column cleaner circuit with a regrind mill. The authors installed a model-based expert, optimizing control system to maximize copper recovery in the bulk flotation circuit while maintaining an appropriate copper grade in the cleaner feed. The optimizing control system uses on-line assays and calculates and implements set points for cell pulp levels, air rates and reagent addition rates. It combines the power of a dynamic population balance model which estimates mineral liberation in each stream, an optimizer which computes appropriate set points and a rule-based module which implements the strategy. The benefits have been evaluated over three months. The model-based expert, optimizing control system generates a measurable increase in copper recovery, around 0.5 per cent and an optimized bulk concentrate grade. The need to maintain the optimizing control system and other practical aspects are discussed.

Jan 1, 1998

The past four years since the 2008 MINExpo have been a roller coaster ride for the mining industry, with highs and lows and everything in between. One of the natural consequences of this uncertainty has been a number of significant consolidations and mergers, and this trend has trickled down into the crushing industry. And while there have been some significant changes to this sector of the mining industry, many of the big players have weathered the storm. The following is a look at some of the mineral processing companies that will be at MINExpo. McLanahan Corp. McLanahan Corp. is an example of the changes in the sector. The crushing and grinding stalwart acquired Universal Engineering, expanding its traditional focus on soft mineral crushing to hard rock crushing. At MINExpo, it will be showing off three new pieces of equipment, the LabMill Crusher, the Rocker Tooth Crusher and the Recessed Filter Press.

Jan 1, 2012

By D. K. Adjei, G. Ofori-Sarpong, R. K. Amankwah

"Mercury (Hg) is toxic and has long-term effect on the muscle tissues, the brain and the central nervous system functions due to its bioaccumulation and biotransformation effect. Hg pollution around the world is high and this has attracted much global concern such as the Minamata Convention on Mercury, held in 2013. For several years, mercury has been the chemical of choice for Artisanal and Small-Scale Mining (ASM) gold extraction, accounting for about one-third of the global mercury consumption. A greater percentage of this ends up in the environment through open burning of amalgam, spillage and indiscriminate disposal of waste. To break this wall of mercury pollution, it is very important for the mercury used to be recycled through the use of mercury retort units. This brings into the limelight, the Lantern Retort which tries to synergise the high conductivity of steel and the see-through effect of glass, thus, improving the amalgamation process. A research conducted on improving the original Lantern Retort arrived at an appropriate distillation length of 5.08 cm which was used in redesigning a more efficient retort. The improved Lantern Retort recovered about 98% of the mercury used. INTRODUCTION Artisanal and Small-scale mining (ASM) is an informal mining activities which employ quite simple tools such as pickaxes, sluice boxes, shovels, chisels, metal bars, mattocks and water pumps for mining and processing of gold ores. The artisanal and small-scale mining (ASM) sector has served as source of employment for many people in developing countries including Ghana (Aryee, 2001; Hilson and Potter, 2003; Amankwah and Anim-Sackey, 2004; Amankwah et al., 2010) and has provided a substantial amount of foreign exchange through its activities (Hilson, 2001; Styles et al., 2010). Hentschel et al. in 2003 estimated that about thirteen (13) million people are said to be engaged directly in the small-scale mining activities worldwide. However, an estimated 100 million people are said to depend on this sector for their livelihood mainly in developing countries. In China alone, a projected number between 3 and 15 million people are engaged in artisanal and small-scale mining activities (Hentschel et al., 2003), whilst in Ghana, it is estimated that more than 1,000,000 people are employed directly or indirectly in the artisanal and small-scale mining activities, with 10% being women (Amankwah and Anim-Sackey, 2004; Amankwah and Ofori-Sarpong, 2014). In Ghana, ASM gold production has grown from a low of 2.2% in 1989 to a high of 34% in 2014. This figure is estimated to increase with proper documentation. This indicates that the sector has made significant socioeconomic impact on many individuals and communities as a whole. Notwithstanding the above positive contributions, the sector has also contributed to negative impacts on human, aquatic life and the environment in general due to indiscriminate mercury emission. This ‘pollution wall’ needs to be broken, and several interventions have been put in place including the use of retort units like the lantern retort (Adjei et al., 2014; Amankwah and Ofori-Sarpong, 2014)."

Jan 1, 2017

By D. R. Spears

Conventional round tank thickeners have been widely used in the mining industry for many years. The mining industry was well satisfied with the ability of conventional thickeners to improve minerals beneficiation operations. However, development of improved flocculants (the polyacrylamides) made possible much more rapid settling rates, since polyacrylamides produce large flocs rapidly (unlike starch or inorganics). Traditionally considered to be a slow operation if maximum underflow density was achieved, and therefore there was some justification for the expense. Thickeners required large volumes to permit sufficient time for settling. The oversize not considered a drawback but the initial capital cost was. In high rate thickeners, a bed of thickened material is allowed to build around the feedwell, even above the bottom of the feedwell. The slurry is fed directly into the bed at a velocity that allows the material to be evenly dispersed over the thickener area This more efficient use of settling area allows a higher solids throughput per unit surface area (rise rate). In this paper, high rate thickener rise rates and polymer consumption are compared.

Jan 1, 1998

By Stephen L. Chryssoulis

The detection and quantification of invisible gold by microbeam techniques is discussed. Ion probe microanalysis is used to quantify the gold content of individual sulphide, sulpharsenide and oxide particles with a detection limit of 0.2 ppmw (g/t). The proton microprobe is used to determine the gold concentration of gangue minerals with a detection limit of 2 - 4 ppm. Using these techniques complete mineralogical balances for gold are obtained to assist in the process selection and optimization. A total of twenty gold and gold-bearing ores have been examined. Selected examples are presented.

Jan 1, 1990

By Christopher J. Vise

Although production operations at mines, representing the extraction and removal of the mined material, often appear to receive the greatest amount of attention, the emphasis given to auxiliary operations is continually increasing. This is due to the changing economic, social, and environmental climate in which modern mines must operate. Auxiliary operations can best be described as those activities that are not directly related to the extraction and removal of the mined material, but must receive proper attention if recovery is to take place in a safe, efficient, and socially responsible manner. In fact, certain mining auxiliary operations, such as strata control and ventilation, are considered to be of such importance that they warrant separate sections in this Handbook. Judging from a mine-personnel standpoint, it is not uncommon for a mine to hire the same number or more individuals responsible for auxiliary operations as the number assigned to production.

Jan 1, 2008

By Thomas J. Wright

The evaluation and development of the Eastern North Carolina phosphate deposit resulted in one of the world's largest and most modern phosphate mines and fertilizer complexes at an investment in excess of $90,000,000. The resulting ore beneficiation process showed excellent correlation with pilot plant data. A number of variations from current industrial practices were introduced and projected from bench scale tests through pilot plant to production. Principal among these variations were the following: 1) removal of magnesium by classification, 2) simultaneous flotation of coarse and fine phosphate, 3) the use of saponified fatty acid, 4) utilization of filter wash water for deoiling, 5) utilization of a rougher concentrate for acidulation, 6) calcination of flotation concentrates, and 7) elimination of grinding prior to the manufacture of phosphoric acid.

Jan 1, 1971

By John C. Bowling

Many recent mine developments in North America are located in remote northern regions with extreme winter temperatures in the range of -20oF to -60°F. In addition, many locations are subject to very heavy snowfall. This paper discusses some of the key considerations in the planning and design of mine plant buildings, particularly concentrators, located in these regions. SUMMARY & CONCLUSIONS The subject is considered under three main headings: I. Building Out line and Structural Frame 2. Wall and Roof Materials 3. Foundations The plan outline of a mine plant building will naturally be governed by the scope and layout of the process equipment it contains. The selection of roof profile, on the other hand, will generally depend upon a number of factors extraneous to the process e.g. snow conditions. When these factors are considered for concentrators in cold locations, a flat or stepped roof will usually be more economical and suitable than a sloping roof. The materials normally used for the structural framework of concentrators are the same as used for other industrial buildings, namely steel, concrete and wood. Structural steel, however, is the most commonly used material for concentrators in

Jan 1, 1971

By W. H. Jang

Recent research has demonstrated the utility of the FTIRIIRS adsorption density equation for in-situ study of surfactant adsorption phenomena at the surfaces of reactive internal reflection elements (IREs). The FTIR/IRS adsorption density equation is given by (formula) where r is the adsorption density, A/N is the absorbance per reflection, e is the integrated molar absorptivity, 4 is the bulk concentration of the surfactant, d. is the effective thickness, and dP is the depth of penetration. Previously, the validity of the adsorption density equation had been confirmed only from solution depletion measurements with high surface area powders. Now, FTIR/IRS studies of Langmuir-Blodgett (LB) monolayer films of fatty acid transferred to the surface of a calcium fluorite IRE .clearly validate the reliability of the FTIR/IRS adsorption density equation for quantitative analysis of surfactant adsorption. In addition, it was confirmed from the observed absorption band at 1550 cm-1 that the first monolayer of the transferred fatty acid chemisorbs at the surface of fluorite.

Jan 1, 1994

By M. Hakan Morcali, Onuralp Yücel, Haldun Gürcan, Serdar Aktas, Semih Özbey, Alper Keskin

"This work presents a method for the precipitation of cobalt sulfate by alcohols, specifically ethanol and methanol. The effect of the initial concentration of cobalt, the volumetric ratio of alcohol to cobalt sulfate solution, the addition of sulfuric acid and ammonia, and the effects of common ions on the precipitation percentage were investigated. The performances of ethanol and methanol were compared in terms of the precipitation percentage of cobalt sulfate, and explanations for different performances are offered. In the sulfate-based solution, the alcohol was shown to displace water ligands from the first coordination sphere of the cobalt(II) cations, which led to the precipitation of the cobalt ions as cobalt sulfate heptahydrate. SEM analysis revealed that the particle sizes of the powders produced by this method are smaller than those of commercially available cobalt sulfate. The scientific literature contains no data on the solubility of cobalt sulfate in ethanol. In this study, the solubility product constant (Ksp) for cobalt sulfate was experimentally calculated to be approximately 1.15 x 10-5.IntroductionCobalt sulfate, which is one of the most important compounds of cobalt, is used in the electroplating and electrochemical industries. The addition of cobalt sulfate to nickel-plating baths makes the treated metals brighter, harder, smoother and more ductile (Armstrong et al., 1988). It is also used as a desiccant for lithographic inks, varnishes, paints and linoleum, as well as in storage batteries, e.g., nickel-cadmium (Ni-Cd) and lithium-ion (Li-ion) rechargeable batteries (Kang et al., 2010). Cobalt sulfate is employed as a coloring agent in ceramics, enamels and glazes to prevent discoloration and as a copigment for the decoration of porcelain. In addition, cobalt sulfate has been used in animal feeds as a mineral supplement (Budavari et al., 1996; Kirk and Othmer, 1999).In the past, brewers used cobalt sulfate to prolong the life of beer foam (Kesteloot et al., 1968). Ranchers have dosed livestock with cobalt sulfate or used fertilizer enriched with this mineral to ensure that their animals obtained sufficient amounts of the trace mineral, which is essential to the production of vitamin B12. Cobalt sulfate has also been used in veterinary medication to prevent and treat cobalt deficiency in ruminants, which causes a reduction in feed intake and body weight, accompanied by emaciation, anemia and debility.Cobalt sulfate is a water-soluble bivalent cobalt salt. Cobalt sulfate heptahydrate dehydrates entirely at 420° C, and the dehydrated salt forms red monoclinic crystals."

Jan 1, 2015

By Bror Nyman

Wide settlers are a way to decrease the linear velocities of advancing liquid phases. It has, however, been found unnecessary to risk a proper settler performance by building shallow settlers in order to avoid a so-called interface turbulence due to a too big difference between the linear velocities of the organic and the aqueous phase. This conclusion has been reached from tests using a large transparent settler model, where the behaviour of a clean interface between two advancing liquids has been investigated. Also in a more realistic case, making an organic in aqueous or an aqueous in organic dispersion to move between the liquid phases, no obstacle has been found to use a somewhat more deep and correspondingly ore slowly t10wing aqueous phase. Based on above findings, support can be given to a new trend to build the settlers slightly deeper than what has been typical for the so-called low-profile design. In this way, it is much easier to avoid an excessive air introduction and other severe difficulties, like those caused by crud moving from one stage to another. It is further shown, how gravity can be used to slow down and distribute a dispersion being fed into a settler of a VSF unit. Entrainment levels have been found to be reduced by a careful design of primary dispersion distributors and picket fences of the settler. Finally, it is demonstrated, how outlets from the side of the settler can be used to simplity interstage pumping and to decrease the rotation speed of any pumping device.

Jan 1, 1996

By K. L. Gabby

Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately mercury is recovered along with the silver as mercury/silver/gold amalgam which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness, while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution.

Feb 23, 2014

By Andy Thompson, Frank Perrone

"As part of the Metropolitan Transportation Authority’s $10.5bn East Side Access Project in New York, 3,200 m of tunnel had to be constructed in rock, mix face and soft ground conditions beneath one of the largest passenger railroad junctions in North America, handling over 780 trains per day. The use of risk based decision making tools was essential in developing the bespoke contract framework that was adopted as well as making informed decisions once excavation commenced. This paper will outline the risk management process adopted, discuss the risks and mitigation strategies adopted and comment on the impacts of this approach on the as built Project cost and schedule. In particular, the paper will outline the unique approach used to establish the baseline against which the Contractors performance would be measured as the selection of a Slurry TBM to excavate the tunnels was considered to compromise the effective use of a Geotechnical Baseline Report. BACKGROUND AND CHALLENGES Contract CQ031, Queens bored Tunnels and Structures was awarded in September 2009 to a joint venture of Granite Northeast/Traylor Brothers/Frontier Kemper (GTF JV) for $717.6m following a negotiated procurement process. A robust approach was taken with regard to the management and payment for risks associated with the construction of these tunnels. Risk assessments were carried out during the design phase and a risk register was developed prior to procurement. During the procurement phase close attention was paid to ensuring that the allocation and pricing of known risks, together with mechanisms for managing future risks were clearly defined between the MTA and GTF JV.In comparison to the excavation work in Manhattan, which was performed in competent hard Manhattan schist, the tunnels in Queens were excavated predominantly through soft ground with a high water table and complex environmental conditions. Not only did this require the use of pressurized face TBM technology, a first in New York, but also a re-evaluation of the contractual mechanisms used to manage the hard rock excavation contracts for their appropriateness to the soft ground tunnel work."

Jan 1, 2016

By K. V. Raj, T. Bhowmick

"Control of fugitive dust in high latitude open-pit mines is challenging due to unique atmospheric phenomenon resulting in complicated flow regimes, and atmospheric inversion due to lack of adequate solar insolation during prolonged winter seasons. In this study, two idealized (One conical and one trapezoidal) three-dimensional open-pit mine geometries are simulated for differing seasonal conditions using the CRADLE-CFD package. The airflow is modeled using Standard Kappa-Epsilon Turbulence Model solved by RANS equations. The concept of particle tracking is used to predict the flow pattern of dust particles. For various climatic conditions, and two different pit geometries, fugitive dust particles varying in size (PM0.1 to PM10) and concentration are generated at various locations of a mine and dispersed by the airflow pattern inside the open-pit mine. The amount and location of dust particles inside the pit is reported at various time intervals. The development of atmospheric inversion during the winter season significantly affected the amount of dust retention inside the open-pit domain. While during the summer, airborne dust particles were transported outside the open-pit domain in a short time. INTRODUCTIONComputational fluid dynamics (CFD) modeling of open-pit mines is challenging. In a recent paper, Bhowmick et. al. [1] presented different constraints and challenges in developing a 3-Dimensional CFD model. In order to obtain realistic results from a simulation, however, appropriate values of various inputs are required. Simulation results of a 3D non-hydrostatic model by Shi et al. [2] showed that both the mechanical and thermal forcing are important mechanisms, controlling the development of the atmosphere inside an open-pit. Alvarez et al [3] used a CFD model for predicting dust dispersions in a medium sized limestone quarry, and presented several iso-surfaces of varying dust concentrations using ANSYS CFX. A similar study by Torno et al [4] introduced a more sophisticated parameterization of the dust sources. Flores et al. [5] used an OpenFOAM CFD simulation package to simulate and predict pollutant dispersion in an idealized and an actual open-pit mine in Chile with an intense insolation condition. The model was simulated for three different conditions: (i) air advection (10 m/s) driven mechanical turbulence; (ii) surface heat flux (240 W/m2) driven thermal buoyancy; and (iii) both air advection and surface heat flux driven conditions. The results of the simulations showed that the buoyant currents contribute to the removal of a large percentage of the dust particles. The buoyant currents modify the purely mechanical-turbulence induced flow pattern and reduce the particle residence time, commonly observed in a purely mechanical turbulent flow (non-buoyant case)"

Jan 1, 2015

By Tim Langmaid, Steve Skelhorn, Stephanie Robillard, Allen Mitchell

"The Port Mann Main Water Supply Tunnel project provides a critical water main crossing of the Fraser River for the owner, Greater Vancouver Water District (Metro Vancouver). The project consists of two 60-metre-deep slurry panel shafts and a 1-kilometre-long, 3.5-metre excavated diameter tunnel located near Vancouver, British Columbia, Canada. The initial tunnel lining is a precast concrete steel fiber reinforced gasketed segmental lining. The final lining is a 2.1-metre-diameter welded steel pipe. This paper describes the challenges encountered during tunnel construction and the solutions implemented. Key challenges include earth pressure balance tunnelling at up to 6 bar pressure—the highest to date in Canada—a water-crossing without surface access for the majority of the tunnel drive, ground freezing from a river platform for a critical TBM intervention, and boring through cobbles and boulders in dense glacial till. INTRODUCTION Metro Vancouver supplies drinking water to 18 municipalities, one electoral district and one treaty first nation, serving a population of more than 2.4 million residents. Water is collected in three mountainous watersheds to the north of the Greater Vancouver area, in southwestern British Columbia, Canada. To supply the growing demands of Metro Vancouver’s customers, treated water must be conveyed across two significant water bodies: the Burrard Inlet and the Fraser River. The existing Port Mann water main is one of several key links between the watersheds north of Vancouver and the municipalities south of the Fraser River. The Port Mann Main Water Supply Tunnel (PMMWST) is the first of a series of upgrades, to increase capacity, enhance scour protection, and improve seismic resilience. The new tunnel is 3.5 metres (11.5 ft) in diameter and 1 kilometre (0.6 mi) long. When completed, it will contain a new 2.1 metre (7 ft) diameter steel water main that will help ensure the continued, reliable delivery of drinking water to these municipalities, and will more than double the capacity of the existing 1.2 metre diameter main."

Jan 1, 2016

By R. Mishra

The validity of the concept of mine resistance in ventilation systems is examined. Mine resistance is the proportionality constant relating the head generated by a fan and the quantity flowing through it when the fan is connected to a mine circuit. It is the total effect of all branches in the mine ventilation circuit. Its importance lies in the fact that for new mine projections, and in the extensions of existing mines, ventilation calculations are usually based upon adjustments of the mine resistance. In ventilation circuits with regulation, and/or with multi-fans, simple adjustments of the mine resistance curve do not lead to correct solutions. A ventilation system consists of several interconnected subsystems where one subsystem behavior affects that of the others, and the total system. Through a series of simple but realistic examples, the authors will demonstrate the importance of the systems concept in mine ventilation, and its practical application to coal mine ventilation planning.

Jan 1, 1977

By Tim Arnold

"Justified is a show on FX that takes place in Kentucky coal country. The two main characters, a cop named Raylan and a criminal named Boyd, are adversarial to the very end, yet they manage to maintain a seemingly inexplicable bond of friendship through it all. The final episode ends (spoiler alert) with Boyd asking Raylan why that is. He responds, “If I allow myself to be sentimental, there is one thing I wander back to” Boyd responds, “We dug coal together.” Fade to black.What creates these types of bonds between friends and co-workers in mining? I don’t know about you, but many of my best friends I met in mining. Certainly the people I respect the most in this world are a part of our industry. Good, honest, honorable men and women. And I am not just talking about the leaders of our industry. I am talking about great miners who taught me how to do the right thing and also be productive.I have had the pleasure to work for some great people and the misfortune of working for some of the loudest screamers. What I consider the worst butt-chewing in my life may surprise you. I once worked for a man I respected, because he showed me respect. He went on a business trip and left some instructions. For some reason, I was able to justify to myself that they applied to everybody but me, and I disobeyed them. When he returned he called me into his office and said to me: “Tim, you pissed me off when you did that.” He said it quietly and with no anger. I had lost his respect. This devastated me more than any screaming shift boss ever could have. I learned a lot about values from that conversation.Most of us will spend more time at work than we will with our families over a lifetime. It is natural that tight bonds be created at work. What I believe makes mining special is that these bonds are so strong. They are strengthened by the incredibly hard work our miners do. They work at all hours, on holidays and in all sorts of extreme weather conditions. The physical demands of the job are sometimes exhausting. Our bonds are further reinforced because the work is dangerous. Not only does management watch out for the wellbeing of their people, but each and every one of us looks out for one another. The bonds are made tight because our people are so passionate about what they do, no matter the department or profession. Finally, they are strong because of the thousands in the industry that keep doing the right thing, every day. We make great friends in this industry because of the strength of character of our people. That is why Boyd and Raylan respected one another so much."

Sep 1, 2016