Search Documents

By R. C. Bates

Uranium mine workers? daily exposure to radon daughters was estimated by two methods of sampling, detailed and spot-check. Both methods involve time- weighting measured exposure levels to arrive at an average exposure figure. Random sampling, or sampling without regard for the duration of exposure, has proved inadequate for estimating average exposure levels. During the first phase of the study, the breathing zones of eight workmen in three underground uranium mines were sampled for an entire shift; 20 to 36 radon-daughter samples were collected per man-shift, Analysis of these data indicated that a suitably accurate estimate of the full-shift exposure could be made by time weighting a considerable lesser number of representative radon-daughter samples. This analysis led to the spot-check method of estimating full-shift exposures to radon daughters. Additional detailed studies were made in seven mines to Learn more about the full-shift radon-daughter exposures and to test the spot-check method, In all, 617 radon-daughter samples were taken in 10 underground uranium mines during 26 man-shifts, and the spot-check method was tested 35 times.

Jan 1, 1962

By Thomas P. Mucho

Retreat or pillar recovery mining redistributes the overburden weight onto the adjacent coal pillars in a room-and-pillar section. The additional stress and the resultant energy stored in the remaining pillars can become so great that pillars may bump or violently fail. An investigation at the Gary No.2 Mine was conducted to examine the effectiveness of the thin pillar mining method for mitigating bump occurrences. Field observations were made and instruments were installed to monitor pillar behavior during extraction. Stress monitoring instruments and roof-to-floor convergence stations were installed in pillars and entries and crosscuts, respectively. Results indicated that high pillar stress concentrations occurred in these bump-prone geologic conditions. The thin pillar mechanism, the creation and progressive outby movement of an expanded yield zone, was also monitored through the instruments. The expanded yield zone, a result of using thin pillars in a highly stressed pillar line area, mitigates bump risk.

Jan 1, 2010

By T. F. Mitchell, J. V. Batty, R. R. Wells, R. Havens

"INTRODUCTION )ne of the most important wartime activities of the Bureau of Mines was the search for new sources of minerals necessary to the prosecution of the war. As a part of the investigation of strategic mineral deposits in the United States under the Strategic Minerals Act (Public 117, 76th Cong., 1st Sess., Ch. 190), examining engineers of the Bureau of Mines investigated and sampled various deposits of chrome ore in California, Idaho, Montana, Oregon, and Washington, and those deposits that warranted further study were explored by diamond drilling, trenching, and drifting, as re¬quired. During these investigations, samples were submitted to the Ore Dressing Section of the Salt Lake City Station for metallurgical testing. This paper gives data summarizing results obtained from laboratory ore-dressing studies of the chrome ores submitted.Although the deposits range widely in geographical location, the mineral occurrence of all of them is strikingly similar. Chromium, in all of the ores tested, is present as impure chromite or chromium spinel. Although pure chromite (FeCr204 or FeO.Cr203) contains 68 percent chromic oxide, the iron may be replaced in varying amounts of magnesium, and the chromium may be replaced similarly by aluminum and ferric iron. In studying concentration methods as applied to chrome ores, the composition of the chrome mineral is of fundamental importance, because it is manifestly impossible to produce a high-chrome concentrate from a low-chrome chromite by any mechanical process.In all but one of the ores, the gangue material consists of olivine or altered olivine minerals such as serpentine, antigorite, and chrysotile. The exception, the Antelope or from Montana, has a gangue chiefly composed of actinolite, chlorite, and talc."

Jun 1, 1947

By S. G. McAnally

This is one of a series of papers describing mining and crushing methods and costs at cement plant quarries throughout the United States and deals directly with the methods employed and costs obtained at the Reliance quarry of the Giant Portland Cement Co. at Egypt, Pa., although it is more or less descriptive of the methods used throughout the Lehigh Valley cement district. Systems of transportation vary according to local conditions, such as proximity to the mill, depth of quarry floor with relation to the mill level, etc. Methods of prospecting differ mainly in the type f drills used. Systems of storage, crushing, and grinding vary chiefly in the types of units. ACKNOWLEDGMENTS Most of the information regarding the early history of the Lehigh cement district was obtained from the History f the Portland Cement Industry of the United States, by Robert W. Lesley, the first president of the Portland Cement Association. The writer is indebted also to Charles Clader, Giant Portland Cement Co. quarry superintendent, for valuable information regarding present and past methods and equipment.

Jan 1, 1931

By Gary A. Kingston

Chromium resources in the United States are estimated at 1.8 million tons of recoverable chromium contained in 22.5 million tons of chromite-bearing material. Additional resource is presumed existent in large, but as yet undetermined, quantities of material containing less than 10 percent Cr203. No domestic resources are being mined presently (1969). Excluding transportation charges to domestic consuming areas, the total 1.8 million tons of chromim is estimated to be available, in ore or concentrate, at costs up to $0.64 per pound; 63 percent of the total is available under $0.11 per pound; and 38 percent under $0.08 per pound. It is judged that transportation from the resource areas to the existing market centers would add nearly $0.05 to the cost of a pound of chromium contained in ore or concentrate. Technically effective beneficiation methods have been developed for much of the known domestic resource, and further development might reduce costs of processing these materials. However, at present, domestic chromium resources are noncompetitive with foreign sources.

Jan 1, 1970

By K. E. Tame

A resume of the history and state of the art of physical beneficiation of uranium ores is presented along with a detailed description of research on concentration of uranium ores by attrition grinding. The information on flotation, gravity concentration, electronic sorting, and selective grinding was gathered to complement the study of attrition grinding methods. Both dry and wet grinding procedures were investigated as potential methods of upgrading a variety of ore types, ranging in grade from 0.02 to 0.42 percent U308. A Mardun4 disintegrator that employs high-speed rotating paddles in a cylindrical shell lined with interrupter bars was used in most of the dry grinding studies. Attrition scrubbing devices, which impart a violent mixing or attritioning action to ore pulps, and cylindrical mills, employing rods or punchings as grinding media, were used in the wet grinding tests.

Jan 1, 1961

By Oren C. Baptist

Umiat field contains the largest accumulation of oil discovered so far in Naval Petroleum Reserve No. 4 in Arctic Alaska. The Umiat anticline was tested with 11 wells; 6 produced oil in varying quantities. Behavior of the wells during testing was unpredictable. For example, one well was abandoned as a dry hole after all tests failed to recover any oil, yet an offset well, only 200 feet from the dry hole, produced 400 barrels of oil a day. The main oil reservoirs are less than 1,000 feet deep and are in the permanently frozen zone (permafrost). Reservoir pressures are low, and most primary production will be by expansion of gas-in-solution in the oil. Because of the unusual reservoir conditions and the difficulties encountered in drilling and completing the wells, the Department of the Navy asked the Federal Bureau of Mines to make laboratory studies of the reservoir sand to determine the cause of well plugging and to provide laboratory information, to be used as an aid in estimating oil recovery from frozen reservoir rocks under solution-gas expansion from low-saturation pressure conditions.

Jan 1, 1960

By David L. Bickel

Stress-relief techniques and instrumentation have been developed through many years of research in the Bureau of Mines and successfully used to determine the in situ state of stress in rock. This report describes the Bureau's three-component borehole deformation gauge and the drilling equipment and accessories used with it. Operation and calibration procedures for the deformation gauge are discussed in detail, along with site selection and overcoring procedures. Information and references included in this publication provide a guide to the Bureau's cover-coring method for determining rock stress.

Jan 1, 1985

By W. W. Fowkes

The Federal Bureau of Mines examined a low-temperature tar obtained from a small-scale commercial unit for carbonizing North Dakota lignite for products that might be important to the economic processing of the tar. Tie tar may be divided into three distinct parts: (1) Tar acids, 45 volume-percent; (2) tar bases, 1 volume percent; and (3) neutral compounds, 54 volume-percent. It has a boiling range of approximately 150° to 380° C. (the decomposition temperature) and yields 18 weight-percent as hard pitch. The tar distillate up to 365° C. may be separated as: (1) Tar acids, 48 volume-percent; (2) tar bases, 1 volume-percent; and (3) hydrocarbons, 51 volume-percent. The tar-acid distillate, boiling to approximately 265° C., was characterized in some detail; the neutral fractions and the tar bases were less thoroughly examined. In general, as might be expected of a primary low-temperature tar, the lower boiling fractions are less in quantity compared with the usual high-temperature tar. The homologous series of each major class appears to be rather complete, although some components are present in very small amounts. The tar is quite unstable thermally, and might be more conveniently processed by extraction methods rather than by distillation procedures. The neutral fraction of the tar is highly aromatic, and might be considered as base stock for the production of liquid fuels.

Jan 1, 1961

By Deborah A. Kramer

An economic and technical evaluation of a proposed process to recover alumina by leaching calcined kaolinitic clay with sulfurous acid is presented in this Bureau of Mines report. After the insoluble portion of the clay has been removed by leaching, monobasic aluminum sulfite is precipitated from the pregnant leach solution by partial hydrothermal decomposition. Further heating completes the decomposition to an impure alumina hydrate. This intermediate is purified in a modified Bayer process, which includes dissolving the alumina hydrate in a caustic solution at high temperature and pressure, then decreasing the temperature and pressure to precipitate alumina trihydrate. Calcining the trihydrate produces the alumina product. A cost estimate was prepared for a plant producing 1,000 tons of alumina per day, 350 d/yr. The estimated operating cost is approximately $475 per ton of alumina. This is substantially higher than a comparable estimated operating cost for the Bayer process of $250 per ton of alumina. The proposed process does not appear economically attractive, even as a method to modify a current Bayer processing plant to use a kaolinitic clay feed. High capital costs and high energy requirements make the process prohibitively expensive.

Jan 1, 1983

By H. Kenworthy

The purpose of the study described in this publication is to develop methods for recovering simple master alloys or single metal components from discarded and scrapped S-816 alloy, The Bureau of Mines started this investigation late in 1955 after the need became apparent for a method of reclaiming high-temperature alloys from an ever-increasing accumulation of rejected and wornout jet engine turbine buckets. Laboratory studies showed the following: (1) Pyrometallurgical separations are not selective enough, (2) several methods can be used for effective chemical dissolution of the major constituents of the alloy, (3) a master alloy or complex salts of cobalt and nickel can be separated, (4) chromium, contaminated by several other metals, may be segregated, and (5) more time and effort need to be expended in separating the minor constituents and improving the purity of the major metals removed. Difficult and incomplete chemical separations were attributed to the complexity of alloy composition, as were the long tedious chemical analyses o' products. For determination of several of the metallic components, standard methods of separation and routine analytical procedures had to be considerably modified to achieve satisfactory results. The overall technical problems involved in separating S-816 components do not appear to be insurmountable; however, refinement of several of the methods used in this investigation is desirable.

Jan 1, 1961

By J. A. Eisele

The Bureau of Mines conducted bench-scale cyclic tests to determine the composition of recycled leach liquor in the Bureau?s proposed clay/HCl leach/ HCl sparge process for producing Al203 from clay. The data developed from these tests make it possible to synthesize leach liquors for predetermined steady-state operating conditions when conducting large-scale crystallization tests. The results of two sparge tests were compared. One was a 20-cycle test with a 36-pct-HCl concentration in the mother liquor; the other was a 10-cycle test with a 26-pct-HCl concentration in the mother liquor. The effect of impurity concentrations in the leach liquor on the purity of aluminum chloride (AlCl30?6H20) crystals was determined, but there was poor correlation between this data and results that have been obtained from miniplant-scale work.

Jan 1, 1980

By H. L. Bibbs, H. D. Snedden

"INTRODUCTION The use of beryllium and its alloys has increased rapidly during the last decade. Further expansion of its use is limited; in part, by lack of adequately developed ore reserves. The principal commercial beryllium mineral is beryl, which is found chiefly in pegmatites and produced for market as a byproduct of the mica and feldspar industries. The coarse beryl is mined selectively, sobbed and sorted by hand, and then sold without further beneficiation. The known reserves of coarse beryl are small. No method has been available for concentrating small disseminated beryl crystals, so ores of this type have not been mined or have been left on waste dumps. Disseminated ore in low-grade unmined areas and waste dumps on developed properties is a potential source of beryl, provided a method is developed for its beneficiation.Published literature on the concentration of beryl is lacking in detail or deals chiefly with tests on artificial mixtures of pure minerals, and procedures as given were not applicable to the beryl ores tested at the Salt Lake Station. The testing procedures described in this report are independent developments. By employing these procedures, beryl was satisfactorily con¬centrated from several run-of-mine and dump ores, although these ores wore low in grade and part of the contained beryl was finely crystalline and disseminated.Beryl, quartz, and feldspar, when ground to flotation sizes, are so alike in color and general appearance that they cannot he distinguished by visual observation. The progress of the work depended on rapid determination of the grade of test products by means of the petrographic microscope. Small samples of concentrates and tailings were often cut after each addition of reagents, dried, and examined under the microscope."

May 1, 1947

By Lowell Stroud

Ten natural gases containing from 0.023 to 8.4 percent helium were investigated. In seven high-helium samples, the isotopic abundance of Ne21 was greater than in the atmosphere, being supplemented by 33 to 85 percent of "excess" or "radiogenic" Ne21. The ratio of He4/Ne21(rad) in these gases was evaluated and found to vary between 2.9 x 107 and 5.9 x 107 , a factor of approximately 2. Argon concentrations were determined by the isotope dilution method. The isotopic ratios of Ar40/Ar36 in the high-helium gases were from 5 to 75 times the atmospheric value, with the Ar40 being about 80 to 99 percent radiogenic in nature. The ratios of He4/Ar40(rad) in all 10 gases were evaluated and found to range from 4 to 18. The isotopic ratio of N14/N15 in four of the high-helium gases was essentially the same as in the atmosphere; in three cases it was approximately 5 percent higher than the atmospheric value of 272.0. The genesis of nitrogen and the relationship of nitrogen to helium in natural gases were reviewed and are discussed in terms of a theory for the concurrent generation of nitrogen, helium, radiogenic neon 21, and petroleum (hydrocarbon gases and liquids).

Jan 1, 1967

By Mark Sheppard

This p aver is the second of a series recording the results of tests made at various quarries throughout the United States to determine, (1) the relation between the size gradation of feed to, and product from, primary crushers; (2) the particle shape of crushed product; (3) the differences in gradation and particle shape produced by different types of primary crushers; and (4) the differences in gradation and particle shape caused by crushing different kinds of stone. Primary crushing has received comparatively little attention in the technical literature in spite of the fact that the design of the whole crushing plant should be correlated to the performance of the primary crusher.

Jan 1, 1938

By Robert E. Barieau

A list of 163 references to original experimental PVT data on helium is presented for the period 1895 to 1968. The list is complete as of the start of the Helium Centennial Year, 1968, to the best of the author's knowledge. Citations were keypunched for easy updating and are listed alphabetically by author.

Jan 1, 1968

By J. W. Hunter, J. H. Jacobs

"Approximately 355 tons of nodules from Chamberlain; S. D., ore were processed in the 1-ton-per-day electrolytic-manganese pilot plant of the Bureau of lanes at Boulder City, Nev., in a continuous 3-month operation. The ore, ground to minus 48-mesh, was found to be amenable to leaching with acid directly or after roasting under reducing conditions in a Skinner muffled multiple-hearth furnace.Unroasted ore gave an acid-leach extraction of 84 to 88 percent of the manganese, which after neutralization showed an over-all extraction of between 81 and 85 percent of the manganese. The amount of iron extracted varied, but it was always,enough to permit the use of ammonia for neutralization.Roasted ore showed an acid-leach extraction of 89 to 91 percent of the manganese. A large amount of iron went-into solution, so that it was not economical to neutralize it entirely with ammonia. By neutralizing with calcine to a pH of 5.0 and completing -neutralization with ammonia to a pH of a.5 an over-all manganese extraction of 84 to 86 percent was obtained. The slight increase in. extraction on roasted ore probably would not justify the cost of roasting.Acid consumption averaged 1.75 pounds per pound of manganese extracted. Settling rates of the residue in leach solution were to slow to permit clarification in thickeners, but a Moore vacuum leaf filter proved to be satisfactory. Purification of raw leach solution was .accomplished readily by hydrogen sulfide with a low gas consumption. Electrolysis was normal, without difficulty, and with -current efficiency ranging between 62 and 66 percent.The use of Chamberlain modules for the production of electrolytic manganese would result in an operating cost of 0.8316 cent per pound higher than the cost of producing electrolytic manganese from Three Wids ore."

Mar 1, 1946

By W. H. Pomroy

This report describes research by the U.S. Bureau of Mines to design and in-mine test a rapid response pneumatic fire detection system for multilevel metal mines. The relative merits of pneumatic detection are discussed in the context of typical multilevel mine layouts and environments. The Bureau's prototype system is described, with emphasis on design features that counter commonly experienced and/or perceived operating problems with pneumatic detection systems. Finally, the results of a 3-year in-mine performance evaluation of the prototype system are discussed.

Jan 1, 1990

By Wm. O. Vanderburg

This paper describing the mining practices at the Block P mine of the St. Joseph Lead Co. at Hughesville, Mont., is ore of a series of similar papers being prepared by the Bureau of Mines on mining practices, methods, and costs in the various miner of the United States. ACKNOWLEDGMENTS In the preparation of this paper the writer acknowledges the assistance of R. H. Willcomb, general manager, William Thorson, mine superintendent, and B. P. Bellport, mining engineer, of the Hughesville division of the St. Joseph Lead Co.; and of E. D. Gardner; supervising engineer, U. S. Bureau of Mines, Southwest Experiment Station, Tucson, Ariz.

Jan 1, 1931

By Walter Murphy

For a number of years the Bureau of Mines has been studying the properties of crude petroleums produced in the United States and the Western Hemisphere. A number of reports have been published giving the analyses of crudes from the different field and regions as made by the Bureau of Mines Hempel method of analysis.4/ Several of these reports include analyses off crude oils from the Rocky Mountain region.5/ The search for new fields and new producing horizons in old fields in the Rocky Mountain region has been quite intensive during the last few years, and a number of discoveries have been made.

Jan 1, 1937