Search Documents

By T. L. Joseph

"IntroductionThe efficiency of ore reduction in the blast furnace and fuel requirements depend upon the degree of uniformity with which reducing gases can be distributed through the stock column and upon the permeability of individual pieces of ore and sinter. If the ore is fine, the major problem in reduction is to get the ascending gas stream to the surface of the ore-Hard, dense ores of low permeability, mined in coarse sizes, tend to improve the permeability of the bed, but unless they are crushed to the proper size they reach the hearth unreduced.Surveys by the Bureau of Mines have shown conclusively that the gas distribution in the upper three fourths of the furnace is far from ideal. Furnace lines, top design, and methods of charging are important, but more thorough size preparation of the ore is necessary to eliminate size segregation at the stock line, which inevitably leads to non-uniformities in gas distribution.Because of the quantity of sinter now produced close study of the characteristics which determine its behavior in smelting is warranted. As the use of concentrates increases agglomeration will become more of a necessity. Improvements in the physical character of the ore burden are particularly important to plants using coke of poor physical quality. In addition to aiding reduction, improved physical properties of the ore burden will permit the use of higher blast heats, which is equally important.Reduction Tests on Fine Sizes of SinterPrevious reduction tests on minus 0.742— plus 0.525--inch pieces of commercial sinters revealed large differences in porosity and reducibility. The results have been published in a former report. 3 Although the physical properties of the sinter, particularly porosity, were found to be of major importance in determining the rate of deoxidization, it appeared that certain chemical properties of the sinter appreciably retarded the reduction of sinters high in silica. This was attributed to the presence of fayalite, which has been identified by Schwartz and by Luyken and Kraeber4 as an important constituent of sinter. Although furnace operators and metallurgists have assumed that iron silicate is more difficult to reduce than hematite or magnetite, definite data on the reduction characteristics of this material were not available. Tests were undertaken, therefore, to develop a method for de-termining the amount of iron silicate present in sinters so that its effect upon reduction could be observed."

Jun 1, 1934

By Jack Smith

New turbine blades designed to resist ash erosion were tested by the Bureau of Mines in a pilot-scale coal-fired gas turbine. After a total of 1,963 hours, the rotor blades were only slightly eroded; and they had an estimated useful life of 20,000 to 30,000 hours. Changes in aerodynamic design of the blades successfully concentrated the ash at the outer casing, but stepped sidewalls for the rotor drum and wear strips at the bases of the rotor blades are still needed to minimize wear at these points. Stepped sidewalls and wear strips did not adequately protect the stator blades. Ash slightly eroded their leading edges, above the inserts, and cut notches into their trailing edges near the bases. Stator blade life was estimated at 5,000 to 7,500 hours. Blade erosion in these tests was less severe than with previous designs, but more efficient combustors and ash separators are required to reduce the amount and size of ash entering the turbine, to achieve acceptable blade life for commercial operation.

Jan 1, 1967

By W. R. Huff

This report describes the development and operation by the Bureau of Mines of a pilot plant designed for using high-volatile A bituminous coal-in-water suspensions as a source of preheated coal and superheated steam in the pressure gasification of coal with oxygen. Figure 1 on page 2 is a block diagram of the integrated gasification process, in which a total of 70 tons of coal was fed from slurry and gasified. The present work included (1) development of equipment and methods both for mixing pulverized coal and water to produce slurry and for pumping and metering the slurry at gasification pressure; (2) development of equipment for heating the flowing slurry and, because slurry that can be pumped produces more steam than is necessary as a gasification reactant, developing equipment for removing and metering the excess steam; and (3) demonstration of the process under actual gasifier operating conditions, at a coal rate of about 800 pounds per hour and gasification pressures in the range 100 to 300 pounds per square inch gage. By using the forced-convection principle, a flow of slurry made from a caking, high-volatile A bituminous coal can be continuously heated to 600° F. in a coil-type heater. The flow rate and concentration of the slurry and the temperature gradient along the length of the heating coil must be closely controlled. In a radiant-type heater, involuntary reductions in flow rate, even momentary, can lead to coking and plugging of the heater coil.

Jan 1, 1961

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1962, to June 30, 1963, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1963; in general, the research reported in these publications antedates the report period.

Jan 1, 1965

By Louis A. Turnbull

An investigation of coal deposits near Cerrillos Santa Fe County, N. Mex., was undertaken 14 the Bureau of Mines in 1943 as part of a general program to determine sources of metallurgical coal for western steel plants. Almost all of the coal used for metallurgical purposes west of the Continental Divide Is mined from the Lower Sunnyside bed in, Carbon County,, Utah. Coke used in western steel plants that is produced from Lower Sunnyside a coal is weaker, structurally, than coke used elsewhere in this country. For this reason, western coal operators and steel manufacturers are anxious to develop new areas of coking coal of better quality then the coal produced from the Sunnyside bed. The objective of investigations of western coals was to (a) develop additional reserves of coking coal to supplement proved reserves in the Sunnyside bed. and (b) develop; if possible, reserves of coal with coking quantities superior to those of Lower Sunnyside

Jan 1, 1951

This section presents highlights of world economic and mineral industry performance in 1982, a year characterized by continued recession, and selected 1983 forecasts of economic indicators of importance to the mineral industry, some of which indicate a modest improvement in the economies of the United States and Western Europe. The U.S. Economy in 1982 In 1982 U.S. gross national product (GNP) in current dollars increased at a rate of 4 percent, but GNP adjusted for inflation (real GNP) declined at a rate of 1.8 percent. Yearend 1982 real GNP was at roughly the same level as in 1980 (table 1). Thus no growth in real terms had taken place in the United States during the 1980-82 period.

Jan 1, 1983

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1962, to June 30, 1963, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1963; in general, the research reported in these publications antedates the report period.

Jan 1, 1965

By R. E. Morgan

This publication presents abstracts of articles and investigations pertaining to the utilization of fly ash. The terms "fly ash" and "flue. ash," as' used in most of the papers, refer to the ash from pulverized-coal firing collected by electrostatic precipitators or mechanical collectors. Several investigators do not define the material on which they report beyond calling it fly ash, but they probably refer to the fine material resulting from burning pulverized coal. A few of the papers report on investigations involving not only the use of fly ash but boiler slag as well. These can be identified by the title of the articles. Bibliographical information and the abstracts are arranged according to the date the papers were published, with the most recent listed first. With the continually increasing use of pulverized-coal firing, profitable disposal of the fly ash is becoming a problem of greater importance to many utility and industrial companies. Also, in recent years, the public demand for cleaner air, and the more highly efficient fly-ash collectors available have resulted in the collection of a greater percentage of the fly ash produced. The solution to better utilization of fly ash has, therefore, been the object of research for some years.

Jan 1, 1952

By Joseph W. Horne

This report presents the results of an investigation by the U. S. Bureau of Mines in cooperation with the State of Colorado, on the yields and properties of oils produced from oil shale, lignite and subbituminous coal using the standard assay method developed by the Bureau for oil-shale testing,. The purpose of this work, which is part of the general study of oil shales being conducted by the Bureau of Mines and cooperating agencies, was to obtain information on the amount and character of the yield of crude oil or tar from different typical oil shales, the yield of light oil or naptha that might be suitable for use in motor fuels, and other products of shale oil. As the west has large resources both of oil shale and low-grade non-coking coals, it is of interest to know the relative yields of tars, light oils, and combustible gases that can be produced from these coals when retorted under conditions similar to those suited for oil-shale retorting. Source of Samples The coal samples were obtained from deposits on or adjacent to the public lands in the States of the Rocky Mountain region. Many of the mines sampled are operating under Government leases or permits. The number of coal samples secured from the various states are: Colorado, 6; Montana, 9; north Dakota, 6; New Mexico. 1; South Dakota, 1; Wyoming, 9. Of these samples, 14 were lignite coal, 16 subbituminous coal, and a bituminous coal. The standard channel method of the Bureau of Mines was used for sampling. Coal samples received at the Boulder Office weighed about twelve pounds each, and duplicate samples were sent to the Pittsburgh Station for proximate and ultimate analyses. The origin of the samples and description of the deposits are given in Table 1.

Jan 1, 1927

By Carl Belser

Approximately 30 million pounds of tungsten trioxide in the form of ferberite concentrates have been shipped from Boulder County. Since 1940, the production has varied considerably, being affected by the emergency needs of World War II and the Korean conflict. During World War II, attempts to stimulate production were made by the Metals Reserve Company by stabilizing the price for a specified period, the Reconstruction Finance Corporation by small mining development loans, and the Bureau of Mines and the Geological Survey, who cooperatively explored some of the district by surface and underground core drilling. During the Korean conflict and continuing through the first half of 1954) tungsten production was being stimulated by a Government-gauranteed price and by financial assistance loans under the Defense Production Act of 1950 to qualified operators of properties that have merited exploration. This combined program has increased production in Boulder County from about 1,900 pounds in 1949 to an estimated 383,000 pounds of tungsten trioxide in 1953. The 1953 production came from 67 properties. One of the problems confronting producers is the need for improved beneficiaton methods. Ores from the area have not been amenable to flotation concentration and gravity methods have resulted in poor recovery, often less than 70 percent.

Jan 1, 1955

By John W. Sweeney

Shales and clays from Illinois were sampled, tested, and evaluated to determine feasibility of producing lightweight aggregate by rotary-kiln methods. Sampling procedures and the 1 ,,,y of the Pennsylvanian shale units are discussed. Chemical, X-ray spectrographic and X-ray petrographic analyses were run on the samples to determine if a correlation existed between chemical mineralogic composition and expansion. Preliminary expansion testing was conducted in a muffle furnace. Rotary-kiln tests were conducted in a 16- inch by 14-foot rotary kiln. The weight of the aggregate ranged from 27 to 59 pounds per cubic foot. Concrete cubes employing the aggregate were tested to determine the qualities of the concrete. Compressive strength of the concrete using the 7-bag of cement cement per cubic yard mix, after autoclave curing for 6 hours, ranged from 2,950 to 6,750 psi. No correlation was found between the chemical, X-ray spectrographic, and X-ray and petrographic analyses and expansion, Sixteen samples made suitable lightweight aggregates in the laboratory rotary kiln. The expansion temperature range of eight of the samples was extremely narrow, and difficulties would probably be encountered in processing these materials commercially.

Jan 1, 1965

By Lee J. Raabe

A specialized loading system for tensile and fatigue testing of wire rope was constructed and installed in the U.S. Bureau of Mine Wire Rope Test Facility in Bruceton, Pennsylvania. The computer-controlled closed-loop servo-hydraulic test system which can apply up to 800,000 pounds of force on the rope while stretching it up to 30 inches will be used in the development and verification of hoist rope retirement criteria for ropes in the 1 to 2 ½ in. diameter range. Characteristics and capabilities of the system are discussed.

Jan 1, 1984

By Vernon Helm, John S. Ball, Welton J. Wenger, William E. Haines

"INTRODUCTION Although the presence of sulfur causes many petroleum’s to be classified as ""low-grade"" because of the difficulties encountered in manufacturing products to meet rigid specifications, the petroleum industry is finding it necessary to use such crude oils to satisfy present needs. As the demand for petroleum products increases, and available reserves diminish, this utilization of high-sulfur crude oils will be accentuated. Programs designed to supplement the supplies of fuel available from petroleum by the manufacture of synthetic fuel from natural gas, shale oil, and coal are in progress. Such fuels, especially shale oil and, less so, oil from the hydrogenation of coal, also contain sulfur compounds which must be effectively removed. Thus, the need for fundamental research on the sulfur compounds that may be expected in petroleum and allied products is becoming greater as the industry is forced to call upon all available resources to meet the demand for petroleum products. In recognition of this need, the Bureau of Mines has inaugurated a long-range program assigned to furnish fundamental data concerning the presence, characteristics, and effects of sulfur compounds in petroleum and its products."

Dec 1, 1946

By Richard A. Allwes

This U.S. Bureau of Mines report presents the results of structural analyses and full-scale physical tests conducted on a steel-set arch and tri-set. The purpose of the analyses and tests was to evaluate the suitability of these structures for use in roof-fall prone areas. The arch canopy test and design procedures previously developed by the Bureau were utilized in this evaluation. Theoretical resistance functions were established for the steel-set arch and tri-set and were representative of the experimental behavior of the structures. The resistance functions were used to determine the energy absorption capacity of the structures and to predict their dynamic response to impact loading. The dynamic tests demonstrated that the arch canopy design procedure is appropriate for tri-sets and yields conservative designs for both steel-set arches and tri-sets. As a result of this work, it is recommended that these two structures may be considered for use in roof-fall prone areas and for rehabilitation work, provided the arch canopy design procedure is utilized for each application and the principles underlying the design procedure are understood.

Jan 1, 2010

By D. O. Hamiltion

The ISMS program provided for the development and demonstration of equipment modifications in both conventional and continuous coal mining systems. This report describes activities during the demonstration of the conventional equipment and includes machine performance, results of data gathering, system evaluation, and recommendations for implementing improvements.

Jan 1, 1976

By Henry Kreisinger, WALTER T. RAY

In its investigation of more efficient methods for utilizing the coals and lignites in the United States, to the end that waste might be avoided, the value of low-grade coals increased, and the life of the nation's fuel resources prolonged, the technologic branch of the United States Geological Survey carried on a study of the factors involved in the manufacture and use of briquets, including the suitability of various coals for briquetting, the cheapest and most satisfactory binders, and the furnace behavior and evaporative efficiency of briquetted fuel. The investigations had their beginning in the work done at the coaltesting plant at the Louisiana Purchase Exposition, St. Louis, Mo., in 1904, and were continued at St. Louis and later at Norfolk, Va. Accounts of various tests and statements of the conclusions to be drawn from them have appeared in a number of bulletins. a In connection with the work at Norfolk, comparative steaming tests were made in stationary, marine, and locomotive boilers with run-ofmine coal and the same coal formed into briquets of two sizes. The tests in a locomotive boiler that are described in detail in this bulletin were undertaken to add cumulative evidence to work done at other places. They were made possible through the courtesy of the Seaboard Air Line Railway Company in supplying both the locomotive and the coal used. During the trials the locomotive stood on a side track in the shop yards of the railway company at Portsmonth, Va. No running tests were made.

Jan 1, 1911

By H. C. Miller

For nearly a score of years the American petroleum industry has faced the problem of maintaining its economic structure while oil -producing potentialities greatly exceeded the increasing market demand for oil and its products . However , the combination of maximum civilian demand with rising defense requirements caused an all - time peak in crudeoil production in the latter half of 1941 , with a daily production (as estimated by the Bureau of Mines ) of 4,139,000 barrels in December - an increase of 16 percent over the daily production of 3,573,000 barrels in December 1940. In the event of a long war , a continuing , steady, and adequate supply of petroleum and its products for military and required civilian needs is essential, and the efficiency of recovery of oil from natural underground reservoirs will have to be maximum. Whereas it may not be possible to increase production in some fields , the output from others may have to be drawn at a much faster rate than formerly . More than 10 years ' experience in operating oil fields under proration control has demonstrated to petroleum engineers that some of the efficiency of recovery of oil from reservoir sands and rocks is sacrificed if the oil and gas are withdrawn at too . rapid a rate . As petroleum is an irreplaceable natural resource for which suitable substitutes probably will not be available in desired quantities for many years , any producing method that jeopardizes the quantity of oil that may be recovered from underground reservoirs must be considered at this time of declared war against aggressor nations as conflicting with the best interests of national defense . At best, the efficient recovery of oil is a complex problem . It involves not only a knowledge and application of the fundamentals of fluid flow through porous mediums, but the sources of energy responsible for the movement of oil and gas through reservoir sands and porous rocks to wells must be known to determine the best practices for extracting these hydrocarbons . Reservoir energy is of two kinds - (1 ) water under hydrostatic head underlying the oil in the extraneous parts of the reservoir system and ( 2 ) natural gas under pressure as "free " gas in the reservoir or in solution in the oil . Inasmuch as the efficiency of oil recovery depends largely on the manner in which reservoir energy is used to move oil through reservoir sands and porous rocks to wells , optimum practices for withdrawing the oil cannot be determined until it has been established that the oil in the reservoirs is being forced to wells by an internal gas expansion, by a natural water drive , or by a combination of gas expansion and water drive . There is a fundamental difference in the performance characteristics of gas - expansion and water - drive reservoirs . In a strictly gas - expansion reservoir the energy available to move oil and gas through the porous formations to wells results solely from gas pressure , which is maximum when the reservoir is tapped by the first well . Pressures decline as oil and gas are withdrawn ; consequently, the energy available for moving oil and gas through the oil - bearing formations to wells decreases with production . Curtailing the oil - production rate or shutting in gas - expansion reservoirs entirely will not act to replenish energy previously used in the production of oil and gas ; in their operation , therefore , it is especially important not to waste reservoir energy - the production of oil with high gas : oil ratios will be reflected in lower ultimate recoveries of oil .

Apr 1, 1942

Four catalytic converters for diesel exhaust systems were tested to determine their effectiveness in reducing the amount of harmful substances discharged into the air. Tests were conducted with four different catalytic converter designs, using two diesel engines as exhaust gas generators. (Of the four noble metal catalytic converters, three are commercially available.) Testing showed that the catalysts varied widely in oxidation efficiency at light to intermediate engine loads, but that all were very effective in reducing emissions of CO, HC, aldehydes, and odor intensity at heavy loads (engine operating modes resulting in high exhaust temperatures). Particulate loading, particulate size, and NOx emissions were generally unaffected by any of the catalysts. The catalysts had one ad-verse effect on exhaust quality--increased sulfate emissions. Because of the potential problem of sulfate emissions, the exclusive use of catalytic reactors for emissions reduction does not appear to be satisfactory. However, when used with a means for subsequent removal of sulfates, a catalyst can function as a key component in an emissions control system for diesel engines operated in underground mines.

Jan 1, 1978

To provide a simple means for rapidly checking methane concentrations at working faces in coal mines while remaining under permanently supported roof. The Approach: A light telescopic probe, through which a gas sample can be pumped Into a methanometer, has been developed. See Figure 1 [ ] How It Works: The telescopic probe consists of sections of small stainless steel tubing encased in sections of lightweight fiberglass tubing. When fully extended the probe is almost 19 ft. long; fully closed it is approximately 5-1/2 feet long. It can be used In either of these positions as well as at intermediate extensions. An approved methanometer is clamped to the probe by a support bracket.

Jan 1, 1975

The Bureau of Mines human factors research program is directed toward reducing accidents and improving the overall efficiency of the person-machine environment interface found in surface and underground mines. The focus of the hum factors program therefore, is to insure that sound knowledge is available concerning human capabilities and limitations, and that this knowledge is applied to the design, of mining equipment, work tasks, and management procedures. The papers presented in these proceedings summarize some of the recent Bureau research in hum factors. The papers focus on two broad areas, human resource issues and human engineering of equipment, tools, and work procedures found in mines.

Jan 1, 1987